I am in the process of trying to replace a modem/router,the switch does not work with the new modem/router although if I connect the modem/router directly to my computer it works fine,so its not a router issue.I suspect that the settings need to be changed in the switch to allow the new router to work ?
View 1 RepliesWe just purchased 8 managed switches POE to swap out our existing in preparation for our new phone system. We installed them all after configuring with static IP. Deployed... and all but two work fine. Any tips for troubleshooting why two of them do not work? There are a couple other switches in the building. Could it be that a switch "upstream" from the two non-functioning switches is causing an issue? If so, how do I find out? When we put back the two "dumb" switches all was fine.
View 1 Replies View RelatedI have had the switch for about 2 years and recently moved. The manual specifies:
38400 bps and 8-n-1 serial port settings using DB9F to DB9F cable.
I have done this and tried using multiple machines/ports/cables as well as several peices of software (minicom, PuTTy, hyperterminal) and none give me any output from the switch at all.
The trouble is that in its original config, it had 1 port locked into its own VLAN for management with port security and an obscure RFC1918 IP address which I cannot recall for the life of me.
At this point, I have no access to TCP/IP management so serial console is my last hope and is not working.
I want to replace an existing 3560 Switch with another switch of the same exact model and IOS. However, this switch that needs to be replaced is the VTP Server of my LAN at this location. When I replace the switch I will just use the same exact running config but I'm concerned about the vlan.dat file. Do I need to copy that file over to the new replacement switch and if so, what is the best way to do that?
View 5 Replies View RelatedI have a stack of 2960S (c2960s-universalk9-mz.122-55.SE2.bin) and the master has failed (used to have a priority of 14). The second switch has become master (priority 1) as can be seen below: [code]
If I connect a new blank 2960S (same IOS) through the stack ports, will the master sync its config to the new one without causing problems?As I understand the new blank switch will also have a priority of 1 and will by default be numbered as 1. So if the config is correctly synced and I later on want to make switch 1 the master, I need to set the priority: [code]
I need to replace a faulty fan unit on the catos WS-6509 switch. this Catos switch does not support show inventory so any other catos commands which will show me this part id?
View 2 Replies View Relatedmy timer warner router connect to a swith (linksys), and the swith connect to 2 computer. When i restart one of the computer, the internet don't work, but the networking is working, i need to reset the modem by unplug and unplug the line of one computer (so only one computer is hook up to swith and then to the router).... after i got the internet connection from that computer, then i can hook up another computer successfully. But after I reboot one computer, the internet connection won't work again
View 1 Replies View RelatedHow to replace fan incisco 2811 router in live or down condition?
View 2 Replies View RelatedMy home router is an aging D-Link DGL-4100 and I am looking to replace it.My max budget is ~$250 USD.
I use 2 Ubiquiti Unifi UAP-Pro APs in my home for WIFI access, so I have the WIFI aspect of my home network covered completely. All wiring in my home is either Cat5e or Cat6, my switch is a gigabit HP ProCurve 1810G-24, and my cable modem is a Motorola SB6120 (Comcast cable broadband). I have 7 IP cameras (security system), 4 streaming media players, several PCs, a server, and several other network connected devices. I am the only resident.
I am looking to maximize my WAN to LAN (& LAN to WAN) throughput while maintaining a very secure network. I also want the router to have reliable VPN. If it is a wireless router, I would most likely not utilize the WIFI feature, probably turning off the WIFI radios and just use the router functionality.
I don't have the time/patience to build a PFSense (or similar) box and learn the software, so am only considering an off-the-shelf solution. Yes I know that PFSense and Untangle are great, I simply don't have time to learn them presently or in the foreseeable future.So, which router for wired performance and security would you recommend?
In change network topology, we are going to assign PC's Gateway as Switch (3750X) IP Address rather than server IP Address. Currently we have configured all Sytems's Gateway is Internet Server IP Address which we are going to replace with Switch IP as Gateway. [code]
Issue is while connecting specific application like team viewer in which application tried to send keep alive message to the live server and in case of switch/router IP as gateway. Connection doesn't established. However it is working fine when Internet Server IP treated as gateway.
We use a 3825 router to screen alot of the junk from the internet side or our firewall. Its worked well for the last 4 years buthas rebooted multiple times in the last month for no apparent reason.At this point I think I would prefer to replace it.Our current internet link is 100Mbps and this router handles that quite well. Is there an equivalent that I should replace it with, or should I just buy another 3825 ?One with an OOB management port would be nice.
View 6 Replies View RelatedOur one of the Client need to replace CISCO 831 router with high end router , there will be around 60 to 70 users accessing this router for Internet surfing. Right now 831 having 3 Ethernet and 4 Fast Ethernet Ports.
View 4 Replies View Relatedin my lab environment, I have a site-to-site VPN between a Pix515E and Cisco 3845 router, using AES-256/DH-5/SHA for isakmp and AES-256/SHA/PFS group5 for the site-to-site VPN, I can only push about 26Mbps IPSec traffics (tested with Iperf). CPU on the Pix515E is running at 96% utilization
Now if I replace the Pix515E with another Cisco 3845 router, I can push about 100bps. Why such a big difference between the data sheet and actual real world
[code]...
ISP Cable in Smart box. 4 cat 5 cables from various rooms in house to feed cable ready TV's and one from my computer room. Can I connect all cat 5's to switch that is connected to cable modem located in Smart box and connect Wireless Router to cat 5 in the computer room and expect router to work properly?
View 4 Replies View Relatedhow do I hook up a router and a switch together to my cable modem
View 3 Replies View RelatedI had an issue yesterday with no internet access on my desktop computer; the message said "Network cable unplugged" so I called AT&T tech support for assistance. I have 2 Dell computers; a desktop and a laptop which I use wirelessly in the house.After doing several things from disconnecting the router to try and determine if the problem was with my router or an ethernet cable AT&T determined a port on my router which is 6 years old could be going bad and recommended I replace my router.I contacted Linksys yesterday; spoke to tech support for my WRT54G router and was given 2 model recommendations. One was a Model E900 N300 and a more expensive model; an EA2700 N600. There is a price difference of $40.00 USD between the 2 models. I could probably get by with the E900 N300 for $49.99 but the guy at Linksys was putting the pressure on me to buy the more expensive one for $89.99. I told him I'd have to think about it.
View 5 Replies View RelatedI have a 7606-S router ( non redundant ) with SUP32 and i wand to replace it with RSP720-3C-GE , i am asking about the procedure?
-shall i switch off the router ? or just removeSUP32 and insert RSP720 ?
-are there any steps should i do before the upgrade ?
-i am planning to take the router out of service during the operation, how much down time it will be ?
difference between a gigabit switch router and a normal router google email harvesting edited by moderator:removed email addy to protect from spam
View 1 Replies View RelatedI've had my network up and running for several years with no issues. Last week I upgraded my router to a Dlink 826L and now anything connected to my downstream Dlink DSS16+ can't be accessed.
View 3 Replies View RelatedI have a Cisco 1921 to replace our current router which is constantly freezing. We have a couple inside servers, one is a web server and application server which needs to be RDP'd to by a couple of clients outside of our network. I cannot get this to work no matter what. I know it's not the server's setup as when I plug the network back into the old router, it works just fine.
All clients have access to the internet, and I can successfully ping/resolve hosts from both the router and a client computer connected. I cannot, however, rdp using neither our public IP, nor our hostname. The hostname does resolve to our ISP assigned IP, but the server cannot be contacted, leading me to belive this is a NAT issue. [code]
I have a Cisco ASA5505 with Frontier ADSL. I broke into their crappy little modem and obtained the settings needed to replace their modem with a 2621 router with a WIC-1ADSL module. I have a static IP from Frontier which is on my ASA5505 and the Dialer interface on the 2621 gets its address from Frontier via DHCP. There are devices behind the ASA which I need access while in the field, IP Cameras, Seed Treater, etc., so I have Anyconnect running on the ASA and can access everything from my laptop, iPhone and iPad from whereever. The issue arises when my laptop is in house and communicating with my parent company and I try to make a cell phone call off the network extender. The call is choppy since there is no QoS and the data is strangling the voice. Since I have control over the 2621, I added another network and NAT it into Frontier without them knowing. I have since placed the network extender on this network as well as a WAP200 that is wide open for my customers when they are in the office. Doesn't fix the problem but...
I have now added Evertek Wireless internet with a static IP also but they use a reservation based on the MAC Address of my interface of the ASA. This plugs directly intot the ASA via ethernet (I would assume their antenna is just a wireless bridge). I set route tracking on the Evertek side and use the Frontier as a backup and all devices on my NAT network still funcion on Frontier DSL and all my nornal data traffic is out Evertek. The issue is that the Evertek Wireless is not very fast or reliable (today in during a snow storm, it could barely keep an internet connection). And I had a problem with Anyconnect using either connection. I got that working. But think that the "ip address x.x.x.x y.y.y.y dhcp setroute" on the Evertek side messed things up from a routing standpoint when I would connect from the outside on the Frontier side. For testing, I switched the tracking around and now the connection on the Frontier side does not work but that is besides the point.
Frontier is going to try out an ADSL/2 connection next week which brings up another issue; all Frontier connections come into my buidling on a single 4-pair wire so if they go down, all my internet except the Evertek goes down. I have a Raven Slingshot coming for installation shortly that cannot go down; it will provide RTK (sub-inch accuracy GPS) to my customers that have auto-steer and auto-shutoff capabilities in their tractors via cellular data modem. So, while they are planting their crops in the field, if my connection goes down, their tractor will not function.
I also had a Cisco UC320W but it died a few days after it went off warranty so I replaced it with a Dell Server running 3CX IP PBX that supports Cisco SPA525G2 and SPA501G IP Phones. There is a 3CX iPhone app that allows me to receive calls while in the field, it uses a proprietary tunnel that I have open on the ASA. With 4-pair coming into my building, I will be left with a single 1-pair for phones so I am considering a SIP provider instead.
Can/should I move the Evertek ethernet to the third ethernet interface on the 2621 and track the Frontier DSL against the Evertek (backup) on the 2621 side and use the ASA to track the ADSL/2 against the 2621? Should I acquire an 1841 (or some other device that suppports the HWIC) with a ADSL/2 card and use HSRP between the 2621 and 1841? Is that even possible?
I have a 2651 that has an adsl1-wic that I am using as my DSL router. I recently acquired a 2801 that I want to replace the 2651 with. I configured the 2801 the same way as the 2651 but on a reload I get the statement that says
Setup: New interface NVIO placed in shutdown state
When I do a show interface all of the interfaces show up except the NVIO and I don't have any connectivity to the outside world. I am using Nat since I have a /29 and using nat pool overload. What am I missing? I am running IPVOICEK9-M 12.4.25c on the 2651 and adventerprise 12.4.24.T on the 2801
I have had the Netgear 3300 Dual Band for three years. Everytime I wanted to access using my laptop, I had to choose between 2.4G and 5G connection. For about a month now, the 5G does not show up. It doesn't show up as a network to select no matter what device I use. I have reset the router and updated the firmware. Both connection lights are blinking. I recently purchased and IPhone 4 and still I do not have the option of selecting 5G.
View 4 Replies View Relatedinstall a new N600 Wireless Dual Band Gigabit ADSL2+ Modem Router - Model DGND3700, to replace a Thompson Speedtouch USB Modem.
PC Windows XP Home Premium Media addition - Main PC X2 Laptops Win7 & Vista - fully working on wireless no issues.
I have managed to get two laptops working wirelessly with no problems, my main problem is the master pc needs to be able to use this router as well, but I cannot get it to work via the Ethernet cable!! I can get to to the Routers config page, I have done the following:
unplugged and removed the speedtouch modem, the old dial up connection is still available on the pc along with the speedtouch software and driver, I left this in place just in case the pc needs to revert back to the speedtouch modem, if I am unable to resolve this issue.
I have set the ip address on the PC to static and input the relavent Subnet and Gateway I can ping the Routers address 192.168.0.1 even though I have reserved the PC's Mac address and IP Adress I am unable to get to the internet. I have tried setting up a new internet connection via windows wizard.
when i look into the nework connections section in windows the local area connection is 100mb and there seems to be another connection which looks like another internet connection this indicates I am connected however I still cannot get an actual google session running.
I am looking to replace my current WAG54GS Gateway with the EA6500. Problem is the new one does not have a built in ADSL2+ modem (I am in the UK and my ISP is Demon Internet). I therefore need to purchase a separate Modem to connect to the router.
View 9 Replies View RelatedI need to replace a dying Netgear FWAG114 wireless router, and the E4200 gets good reviews so I've been looking into it. I'm a software developer running 6 servers plus 3 laptops and 5+ other devices (iPad, Wii, Droid phones, BluRay...). I prefer to use a trusted PC list (enter MACs for all trusted devices) rather than WEP or WPA - is this available with the E4200?
I don't need VPN, but I do run a number of web servers, app servers and databases, so port forwarding is important - I notice the E4200 provides port range forwarding and single port forwarding - I assume this replaces the Rules and Services feature in Netgear - right?
Do you see any potential problems, given my needs, in using the E4200?
I've recently bought a wag320n modem router to replace the two wire device fitted to my bt business broadband. This router supports a guest network..
View 1 Replies View RelatedI own an HP Pavilion dv6 Notebook PC and recently purchased a Cisco E1500 to replace my aging WRTG54 wireless router. Since installation of the new router I keep getting dropped from my LAN and the internet with "connectivity issues" ... this only occurs on my notebook PC and not the other wireless devices I have in my home. I’ve done some searching on the internet and this seems to be a generic problem with the Broadcom 802.11b/g/n card the notebook uses. I have 2 questions:
1) Is there an easy way to adjust either the card or the router to deal with these issues and if not then
2) what is the best notebook card to replace the Broadcom with to assure these issues go away.
Region : Malaysia
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.1 v0005.0 Build 120926 Rel.27100n
ISP : TM
I am having difficulty setting up the W8968 to replace the router given by TM for the Unifi connection.I tried updating the firmware of the modem router and used quick setup to configure the device as a wireless router using PPPoE, but still couldn't connect to the internet using the WAN port.I noticed there was a guide for TD-W8960N to set up TM Unifi but the web interface is too different from the W8968 interface.
I have a Linksys WRT54G router; have a cable internet connection through the router; and two wired desktops, one running Vista (32-bit) and the other XP. I would like to replace the XP machine with a wired desktop running Windows 7 (64-bit).
View 8 Replies View RelatedWe have upgraded our switch and since then Remote web workplace and owa are not working
View 1 Replies View RelatedMy laptop has both wireless and wired connections but i have been operating on wireless. yesterday the red light which shows my wireless connection on has gone out and it will not switch back on so i have reverted to wired. can you tell me why my wireless switch will not switch back on?
View 1 Replies View RelatedI want to connect a 6911 IP Phone to a SG 300 switch. This is my scenario: vlan 3 data, vlan 9 voice, vlan 10 admin.I have a trunk on port 10 of the SG 300 (vlan 1 untagged, vlan 3,9,10 tagged) and it is connected to a switch 3560, this switch has all the L3 configuration of the vlans and the SG 300 switch has an IP on the admin vlan (10).Also i added the OUI of my IP phones an created an LLDP Policy. Right now I have a 7941 IP Phone working but 6911 is not working. Iam using the new version 1.1.0.73 that supports CDP.
Also I noticed that even when my PC and IP phone receive IP address they can not ping each other nor the SG 300. They only can ping the default gateway or IP addresses in diferent vlans but connected on 3560 switch.