Cisco Switches :: SNMP On SF-200 24P
Feb 14, 2013I need to SNMP on Cisco Smart switch SF-200 24p. I cannot find any option on administration to turn snmp service on.
View 2 Replies
ADVERTISEMENT
Cisco Switches :: Retrieving ARP Table From SF300 Switches Using SNMP?
May 22, 2012I'm setting up an SNMP poller to retrieve the ARP table (ipNetToMediaPhysAddress) from my SF300 switches. I can retrieve the table from SF300-24P and SF300-48P switches running Firmware Version 1.0.0.27, but get garbage for the MAC address when retrieving that same table on the same model switches running Firmware Version 1.1.1.8. Is there an outstanding defect on this code level? How can I retrieve the table showing the IP address to MAC address mappings?
View 1 Replies View RelatedCisco Switches :: VLAN Management Via SNMP On SG300-10 Switches
Aug 7, 2011Any snmpset commands to add, modify and delete vlan table entries on SG300-10 switches? I checked url... however this information is apparently only valid for catalysts. The latest firmware is installed and the provided MIB files are used.
View 8 Replies View RelatedCisco Switches :: How To Configure SNMP On SG300 Using CLI
Feb 3, 2013how to configure SNMP on the Cisco SG300 switches? I have the SG300-10P. I am not fully familiar with the new command line interface on this device, it was easy on the IOS but finding it a nightmare on this one.
I put the following command in but it didnt work.
snmp-server view Interfaces interfaces included
snmp-server community ACB123 ro 10.x.x.x view default
I tried to follow the guidelines on the cisco website but thats all Web interface based, i can only access the switch remotely via CLI.
Cisco Switches :: 300 Series Snmp Backup
Aug 22, 2011we are trying to do an automatic backup of our switches config trough snmp.my script can easily backup cisco 2950-2960-3550-3560 using snmp.but I dont know the mib to use to backup the cisco small business serie 300 switches.
View 6 Replies View RelatedCisco Switches :: 200 Series SNMP Support
May 28, 2013Am I correct in thinking that 200 series swiches now support SNMP using v1.3?
View 1 Replies View RelatedCisco Switches :: SPS224 - How To Save Config Through SNMP
Jun 5, 2011I have Linksys SPS224. I've learnt how to change some parameters through SNMP. But this changes are applying to running-config, and, when switch reboots, all loose.
How can I save this changed running-config to startup-config through SNMP?
Cisco Switches :: SGE2010 How To Trigger Backups Via SNMP
May 15, 2011I have been trying, so far unsucessfully, to trigger backups to a TFTP server of our SGE201 switches. I have testesd TFTP backups via the web interface, and that does work. I need SNMP as I need a scriptable method to trgiger the backups on a regular schedule. I am running the SNMP query from a RedHat Linux server. So far I have the following query work out, but it is failing: [code] The error I am getting is generic, and the same query failed on multiple switches running Software Version 3.0.0.18. The switch is set with the community having full SNMP-admin access from the server's IP address.
View 3 Replies View RelatedCisco Switches :: SG300 Optical Monitoring Snmp-mib?
Apr 10, 2012I was positively surprised to find the optical transmit/receive values using the show fiber-ports optical-transceiver detailed command on a SG300-10.
Now I'm wondering if there is also a SNMP-MIB to query these values? I've already tried the CISCO-ENTITY-SENSOR-MIB used by the larger devices running Cisco IOS, but this didn't work.
Cisco Switches :: SF300-24 Snmp Get Mac-address Information Not Available?
Feb 21, 2013Im sitting with a few cisco sf-300 24 switches and i'm trying to get the Mac-addresses the switch have learned from each computer connected to the switch.
View 2 Replies View RelatedCisco Switches :: VLAN Port Membership Via SNMP On SG300-28
Sep 4, 2011Any snmpset commands to modify port vlan membership on SG300-28 switches? I checked [URL] however this information is apparently only valid for catalysts.
The latest firmware is installed and the provided MIB files are used.
Cisco Switches :: Track Down SNMP MIBs For Linksys By SRW2048
Oct 25, 2011I am trying to track down the SNMP MIBs for the Linksys by Cisco SRW2048. Please note that this is the model before the complete CISCO rebrand of the product. I have SNMP walked, browsed etc etc and I just can't pull CPU and RAM usage. Any working view of those two stats? I'm using OpManager by ManageEngine as my NPM platform.
View 1 Replies View RelatedCisco Switching/Routing :: 3750 - Enable SNMP On Switches?
Dec 26, 2011I want to enable SNMP and track the status/ of the interfaces in switches.
We have Two- cat 3750 (L3 switch) and Nine-cat 2960 (L2)
How to configure the SNMP. any Links provides the required info with an example of configuring snmp will be really useful.
we have OPEN NMS, SPLUNK, MYSQL monitoring tools.
Cisco Switches :: Linksys SPS224 / Creating VLAN Through SNMP
May 30, 2011I have Linksys SPS224Trying to create VLAN through SNMP. Issueing the string to create VLAN ID=100 with name "VLAN100"
snmpset -c private -v2c 10.254.2.144 .1.3.6.1.2.1.17.7.1.4.3.1.1.100 s VLAN100 .1.3.6.1.2.1.17.7.1.4.3.1.5.100 i 4
It reports
Error in packet.
Reason: (genError) A general failure occured
Failed object: iso.3.6.1.2.1.17.7.1.4.3.1.1.100
In same time changing the name of existing vlan snmpset -c private -v2c 10.254.2.144 .1.3.6.1.2.1.17.7.1.4.3.1.1.23 s VLAN23 and even deleting the existing vlan snmpset -c private -v2c 10.254.2.144 .1.3.6.1.2.1.17.7.1.4.3.1.1.510 i 6 are successful.
How can I create new vlan through SNMP?
Cisco Switches :: SG300 Port Counters Via SNMP / Do They Work
May 24, 2013I've got an SG300-10 connected back to back (trunked) with a Cisco 3560X switch, across a fibre link and am seeing some big inconsistencies in terms of unicast data transferred across the ports between them.
During a night time window of 4am - 6am I run backups which involves a large copy of files, that almost saturates a GigE link - we can see from the 3560X end that the link is running at a bit over 800MBit/sec of throughput, sustained. The duration of this transfer is consistent with the size of the files being transferred (ie just over an hour, and is what I'd expect for a data transfer of about that amount). Back-of-the-envelope calculations indicate that the 3560X is measuring this data throughput correctly.
However on the SG300 end of the link, which is also being polled by the same application (Cacti), I'm observing spikey counts of only around 20MBit/sec during that window. These counters are very obviously incorrect - there's a huge amount more data moving across the port than that. The incorrect calculations are showing on both the trunk port out of the SG300 (uplink) as well as the interface where the NAS is connected in (which is an access port).
Cacti is polling the OID: .1.3.6.1.2.1.2.2.1.16.57 which translates to IF-MIB::ifOutOctets.57 = Counter32.I'm running version 1.3.0.62 but this problem is not new to this release - previous releases and 1.2 based releases also had this problem.
It looks like multicast traffic may be being counted correctly (that's only a suspicion though), however what I am certain of is that there is a very large discrepancy with the unicast traffic counts.Is this OID the correct one to be using for this switch?
Cisco Catalyst 2950 - GigE Switches With 64bit IF-MIB SNMP Counters?
Oct 18, 2011which models of HP ProCurve or Dell PowerConnect support 64-bit IF-MIB counters, or for that matter any other manufacturer (Zyxel?) (snmpv2 or v3, OID .1.3.6.1.2.1.31.1.1.1.6)I believe pretty much any Cisco Catalyst above a 2950 do, however don't believe any of the SG series do. I realize I could pick up a 2960G for $1500-2k and be good to go, but I forsee a larger switch purchase in the future, but still could use a switch in the meantime that was able to allow accurate monitoring of closet uplink bandwidth?
View 1 Replies View RelatedCisco Switches :: SG500-28P SNMP Query For Individual Port Power Output?
Aug 26, 2012Is there a way to ask the above switch how much power it's supplying to various ports?I've found some stuff in POWER-ETHERNET-MIB, but it's only the main power supply and the up/down status of the various ports.
It looks like what I want is
[URL]
but my SG500 tells me:
snmpwalk -v2c -cpublic serverswitch 1.3.6.1.4.1.9.9.402
CISCO-SMI::ciscoMgmt.402 = No Such Object available on this agent at this OID
Cisco Switches :: SF-300-08 SNMP Setup Doesn't Show Any Groups In Add User Pulldown
Jun 1, 2012I'm setting up a new SF-300-08 with SNMP.I have defined Groups OK.But, when I go to Add User, the Group pulldown is grayed out and I can't add a user.
View 1 Replies View RelatedCisco :: LMS 4.2.3 And ASA SNMP V3 Not Working
Feb 27, 2013I have ASA running version 8.2.5 and using snmp v3 as below;
snmp-server group Authentication&Encryption v3 priv
snmp-server user SNMP_TEST Authentication&Encryption v3 encrypted auth md5 cisco123 priv aes 128 password123
snmp-server host IN 10.10.10.110 version 3 SNMP_TEST
LMS device credential is as per above SNMPv3 config.Can't get this to work. Digging aroung but no avail. I also try this on ASA 9.1 but same result.
Cisco :: LMS 3.2 With SNMP V3 Not Working
Jul 30, 2012My network is currently running with SNMP v2 configured in easch devices. With snmp v2 our LMS 3.2 server is working fine. However we have planned to migrate our network to snmp v3 . I have configured my few devices for SNMP v3 and added them to my LMS server.
Except DFM module these new SNMP v3 devices are working fine in all other modules. In DFM these devices are reflecting under "snmp timeout" group. I checked with device center -> management station to device; where the SNMP v3 connections are showing "okey"
following are tyhe configuration i have done in my devices.
snmp-server group v3g v3 priv read testr write testw
snmp-server user v3u v3g v3 auth md5 test123
snmp-server view testr iso in
[Code].....
Cisco AAA/Identity/Nac :: How To Get SNMP V3 On ACS
Nov 22, 2012is it possible to get SNMP v3 on a Cisco ACS ?
View 1 Replies View RelatedCisco VPN :: SNMP VPN 3000
Mar 3, 2011I'm not finding where set the snmp community on VPN 3000. I need read flow date on Ethernet interfaces. but I'm able only get traps from VPN 3000 to a system snmp but I don't get read from snmp community to VPN 3000.
where and how to I can configuration the snmp community on VPN 3000.
Cisco :: Monitor PAT Bandwidth With SNMP?
Apr 4, 2012Is is possible to monitor bandwidth utilization of a PAT on an ASA? We're running version 8.2.
View 1 Replies View RelatedCisco AAA/Identity/Nac :: Is There Any SNMP Or Other Notification Available In ACS 5.1
Dec 27, 2010I have not used the ACS5.1 yet so watch out for the easy questions
1) Is it possible to generate report for the users who are inactive for say last 30 days? Customer is looking to audit these users to see if they really need access to any device.
2) Are there any known issues while assigning the priviligaes level to users. In current implementation of this customer users are always logged into priv 1 though they are assigning the priv level of 5. I understand with ACS 4.x we can enable the exec process and assign the priv under user/group policy. What are the configurations that customer might be possiby missing in this case?
3) Is there any SNMP or other notification available in ACS 5.1 where admin can be notified at the time a particulat set of user logs in.
Cisco :: LMS 2.6 Syslog / SNMP Notification?
Apr 3, 2008I am only able to get InfoAlarm messages sent to via email notifications.My switch is sending logs to Cisco Works.Example:
13. 10.10.0.1 10.10.0.1 Apr 04 2008 10:34:41 EC 5 UNBUNDLE Interface GigabitEthernet1/4 left the port-channel Port-channel2 *
14. 10.10.0.1 10.10.0.1 Apr 04 2008 10:34:41 EC 5 BUNDLE Interface GigabitEthernet1/4 joined port-channel Port-channel2
But I only recieve infoalarm messages:
ALERT ID = 00000UE
TIME = Fri 04-Apr-2008 11:04:00 PST
STATUS = Active
SEVERITY = Informational
MANAGED OBJECT = 10.10.0.1
MANAGED OBJECT TYPE = Switches and Hubs
EVENT DESCRIPTION = 10.10.0.1: Cisco Configuration Management Trap:InformAlarm; 10.10.0.1: Authentication Failure:MinorAlarm;
My switch is setup as:
logging source-interface Loopback0
logging 10.10.100.111
snmp-server enable traps bridge newroot topologychange
snmp-server enable traps syslog
I do not recieve critical or warning syslog messages.
Cisco Firewall :: SNMP Server On PIX IOS 7.2 Over VPN
Sep 4, 2011I have a simple query for the issues I m facing currently.I have @ remote site remote site PIX firewall which is configurd to get the Snmp poll on the server locate outside via site to site VPN.There is another snmp server located also in inside which I’m not managing it .
========================================================================
below are the command for the snmp configured on PIX.
snmp-server host inside x.x.x.x community XXXXX ---This is not managed by us
snmp-server host inside x.x.x.x community XXXXX
snmp-server host outside y.y.y.y (private IP tunneled though VPN) poll community YYYYY ---Managed by us
snmp-server host outside y.y.y.y poll community YYYYY
[code]....
there are 2 snmp community & server defined in snmp-server host command for 2 different IP address belongs to snmp server and we can only define one global snmp-server community for any one of them .Question is how the snmp community take a precedence currently I am able to ping from my snmp server from outside to the PIX firewall outside interface over L2L VPN but somehow the snmp server is not listening when i do port query on 161 por!.
Cisco Firewall :: Max SNMP Hosts On ASA 8.2?
Nov 13, 2012Seems like something simple, but can't find on Cisco.com. What are the max SNMP hosts allowed on an ASA 8.2 code? That would be Polls and Traps?
View 1 Replies View RelatedCisco :: (WS-C3750X-24T-S) Fan Status Via SNMP?
Feb 24, 2013requesting information via SNMP from my two stacked C3750X, running IOS 12.2(55)RE5. The stack is up and running and everything is just fine. There are three PowerSupplies installed with a PowerStack, also running like expectet.My problem ist to get the status-information about the chassis-fans. I couldn't find any information about the OID and the search results only in some non-useful information about the MIBs from Cisco which delivers only three information about installed fans (and fan-containers), so I guess these are the information about the fans included within the powersupply?! The chassis-fans are installed and the LEDs are green for all four fan-mounts, up and running.
View 4 Replies View RelatedCisco :: 881 / SNMP Number Of NAT Translation
Jan 5, 2012I am looking for the SNMP OID to monitor the sh ip nat translations on a cisco 881.
#sh ver
Cisco IOS Software, C880 Software (C880DATA-UNIVERSALK9-M), Version 12.4(24)T, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Thu 26-Feb-09 06:01 by prod_rel_team
[code]....
Cisco Routers :: RV 120W SNMP Set
Sep 27, 2011I have the RV 120W router, and can not seem to get SNMP Set to work. I though I would just check here, and make sure it is supported, and if it is, are there any special config settings I need to use?
View 2 Replies View RelatedCisco :: 1242 AG To Manage Via Snmp
Apr 10, 2012Setting up SNMP on my Cisco AP's (1242AG Lightweight). How do I manage these via SNMP? It doesn't appear there is any settings within each AP for SNMP but only on the 4400 controller. What I am trying to do is setup Solarwinds Alerts, so when an AP goes down, I get notified of it. How or where this gets setup on the 4400 or the AP. I'm guessing there is something probably on the 4400 that I setup.
View 3 Replies View RelatedCisco Firewall :: Does 8.4(2) Support Snmp V3
Oct 13, 2011Does 8.4(2) support snmp v3?
View 1 Replies View RelatedCisco :: 6500 - SNMP Time Out
Jun 29, 2011A customer observes SNMP timeout problems on a Cat6500 with IOS 12.2(33)SXI. As a result every 2 days (more or less) all interfaces are marked DOWN and a couple of minutes later all interface are up again - but in fact there is no interruption, it is just the snmp request getting a time out. the customer does not have problems with IOS 12.2(18)SXF14.
In the Bug Details the "Known affected versions" lists the following beside others:
12.2(33)SXI
12.2(33)SXI1
12.2(33)SXI2
[code]...
Now I am confused; both IOS versions are listed as affected (12.2(33)SXI and 12.2(18)SXF14) but the customer does have problems only with one version. Is the customer hitting this bug or is it another one ?
He upgraded 2 Cat65xx on which he observed the problem to IOS 12.2(33)SXI6 and the problem is gone; is this just a coincidence or is CSCed52841 really fixed in 12.2(33)SXI6. This version is not listed as affected but on the other hand, "Fixed-In" lists only these 3:
12.1(22.3)E1
12.2(17d)SXB5
12.2(18)SXD
Before going to upgrade around 50 Core / Distribution switches the customer wants to be sure with the IOS version. Tracing the issue is not that easy because the failure occurs only from time to time.