Cisco Switches :: System LED On SG300 Switch Constantly Flashes
Jan 18, 2013
My problem is that the switch all of the sudden doesn't boot up anymore. The System LED constantly flashes, after probably 40-50 seconds or so it constantly lights for a second, afterwards all the lights on the ethernet ports light up for a second and the process starts all over again! The console messages:
Device configuration:Slot 1 - SG300-10PDevice 0: GT_98DX3033B (AlleyCat2)
-------------------------------------- Unit Standalone --------------------------------------
Tapi Version: v1.9.5Core Version: v1.9.519-Jul-2012 17:55:03 %INIT-I-InitCompleted:
[Code].....
View 3 Replies
ADVERTISEMENT
Mar 19, 2012
I have a Cisco SG300 switch on which trunks are configured. I have a server which sits on the switch via a trunk link of four network cables (4 Gbps total)on which LACP is enabled. I'm having trouble connecting to the server using VNC from a computer on the network. It doesn't happen all the time though, it's just random.
On looking at the logs of the switch, I saw something unusual. The trunk that connects the switch to the server is constantly removing all the member ports and adding them back again after a few minutes interval. That causes the trunk link to flip on and off all the time. What could be the reason that's causing it to happen? I know it could be the network cable but I'm using brand new cables and the server also is brand new.
View 6 Replies
View Related
Oct 15, 2011
I have a SF 200-24P Cisco switch that seems to be rebooting constantly, When i connect it to mains power it seems to go through a startup cycle, in this order - i have tried this with no network devices attached and the same thing happens
1. Fan starts - continously runs
2. Very quick flash of all RJ45 ports.
3. After about 30 seconds, any network devices connected have an acticity light
4. After about another 45 seconds, all ports light up including the activity and POE orange LEDs for about 5- 10 seconds then go off.
5. About 10 seconds later the ports all light up again and stay on for about 5 seconds.
6. All ports go off and the cycle keeps repeating continously.
I have tried pinging the switch without success.I have also tried disconnecting all devices from each port with no success.At no time does the system LED on the left light up.I have tried resetting to factory default with reset pot on the left side.This is a brand new shipped switch from our cisco supplier, could it be DOA?
View 1 Replies
View Related
May 9, 2011
I have a question, does the SG300-28 support VTP and STP?. I want to add it to my network's VTP domain so I don't have to manage vlans manually on the SG300-28 and also be able to configure STP to keep my network loop free.
View 2 Replies
View Related
Sep 10, 2011
I am having an issue with LAG configuration on a Cisco SG300 52 switch. I have connected four Ge ports on the switch to the four NICs of a Dell R710 Server on which I installed Windows Server 2008 R2. Without LAG configured, these ports would forward traffic to and from the Dell server fine.However, if I configure LAG on the ports with LACP enabled, then they would not forward any network traffic. Debugging shows that the ports are up but their forwarding status show N/A. Am I missing any configuration? Can I configure LAG on edgeports?
View 2 Replies
View Related
Oct 12, 2011
Mgmt Vlan 1 (default) Data VLan 10 (with access to internet) Is there a way to have a PC attached to a SG300 switch such that it can both access Vlan 10 for data and Vlan 1 for managment ? The PC's port clearly needs to be untagged PVID on vlan 10. I have tried adding vlan 1T and setting the port as a trunk port but to no avail, The switch is currently level 2. I am guessing this might not be possible in level 2 without setting the mgmt vlan to 10 ?.
View 3 Replies
View Related
Feb 3, 2013
i have a SG300-52 Switch, route mode is enabled, and it is using the latest IOS.I have created 4 Vlans in this switch, till this point its OK, but once i try to give ip addres to the created Vlan either from the GUI or CLI the switch is not responding. i have to go and manually reset the switch using a pin.
View 8 Replies
View Related
Mar 4, 2012
i was trying to set up a new SG300-52 L3 switch for switching and Vlan. The problem is that the vlans on this switch cannot get their DNS resolved. Probably a stupid thing i can't get to see, but i think it is a simple solution given switchin is not my expertise.So my setup:
- ISP Wan router: LAN ip 10.0.0.1, DMZ: 10.0.0.2 -> i have to use this router for ISP support. But it suckes, that's why we use own router for firewall, port forwarding etc.
- Nice Router: WAN: 10.0.0.2, LAN: 192.168.1.1
- SG300 L3 switch
This works. I can ping switch, nice router, ISP router and google's ip from VLAN 5.But i cannot ping google using host name. From within SG300 i can. So it has something to do with SG300 not doing DNS right.My Client on VLAN 5 has ip 10.1.1.5 / 24, default gateway and dns pointing to switch: 10.1.1.1.I have put an entry in DNS servers in SG300: 192.168.1.1 active (pointing to Nice router). On client leave default gateway pointing to switch. But put DNS server : 192.168.1.1
View 11 Replies
View Related
Oct 10, 2011
I have a recently purchased 28 port SG300 switch. Everything is working well. Unfortunately there is so much traffic flying around that a 10MB half duplex device is struggling to function as it is overloaded. Removing some of the sources of traffic fixes it.
Fortunately I only need to access that device from one PC on the network. That PC however needs to access everything else on the network.
Is there a simple way to shield the slow device from everything except traffic from the PC ?
The switch is in Level2 mode at the moment. Everything is on a single sub net.
View 2 Replies
View Related
Sep 1, 2011
We have 2 separate networks here, 1 for data (192.168.0.x) and 1 for VOIP phones (192.168.3.x).
I need them to both be connected to different ports on a switch (Cisco SG 300 10 port managed switch) which is then linked to another switch (Cisco Catalyst 2960 48 port switch). Then on this 2960 switch I want the link to be split back into the 2 separate networks. I think that I need to create 2 separate VLANs and assign them to different ports.
View 2 Replies
View Related
Feb 8, 2013
What does "ip routing" do on the CLI on the SG300? When I do this, I see it enables ip forwarding, but there is no mention of this in the CLI manual. I'm just trying to figure out what I would use this for, and if I should leave it enabled, or disable it. I have several different SG300 switches in L3 mode, and they are set up in a multi-vlan environment...
View 2 Replies
View Related
Oct 22, 2011
I've seen lots of posts from people having problems routing traffic between two vlans with some complicated examples. Any simple step-by-step example for an SG300 switch (in layer 3 mode) to configure two vlans and sending traffic between the two vlans without an external router?
-VLAN1 10.10.10.0
-VLAN2 10.10.20.0
I've tried to do this through the GUI and can't seem to make it work. I'm missing something in the GUI.
View 6 Replies
View Related
Sep 11, 2012
I discovered on a pair of SG300-28P.
On a second switch (ver 1.2.7.76) when I unplugged the power cord, to my amazement the switch turned right back on (about 1 second later), with the power cord removed. To verify that the power is indeed coming from POE, the upstream switch (ver 1.1.2.0) that is the same model (sg-300-28p), shows all 7 Ethernet ports connecting the two drawing from 2700mW, to 3000mW.
While the second switch is powered from the first over POE, the POE does not work on the second switch to power anything, and the system summary mentions something about "PoE Power Information on Master Unit".
Is this a stacking operation, and is POE on the second switch NOT supposed to work when powered over Ethernet from an upstream switch?
View 2 Replies
View Related
Apr 28, 2013
I have inherited a custome with a bunch of SG300's in their LAN room and one out in the warehouse.I need to setup a VLAN and the genius before me did not label which LAN room switch the warehouse unit plugs into. Is there a tool/method I can use to find which switch, and port this warehouse switch is connected to?
View 2 Replies
View Related
Dec 5, 2012
I am having some issues with getting DHCP Relay to fuction properly over our SG300-20 Switch.Out current layout is as follows. Hanging off the SG300-20 are a pair of Clustered Checkpoint Gateways with VLAN'ed interfaces in Both of our 2 VLANs, a 3COM 4200G In VLAN1 which has the DHCP server (And all the other Servers) connected to it, and a Pair of HP Procurve 2520's Stacked in VLAN 2 to provide PoE for our Phones/connectivity for our PCs.The problem is I cannot get the DHCP Relay to fuction from VLAN 1 to VLAN 2. If I assign an address in VLAN 2 manually to a device connected to the Procurves, everything works fine. I am able to reach both VLAN 1 and VLAN 2, but DHCP aquisition fails even if the device is connected directly to a port assigned to VLAN 2 on the SG300. The SG300 is running at Layer 3 currently also.
Here is a copy of the running config:
--------------------------------------------------------------------------------------------------------------
switch4db24f#show running-config
vlan database
vlan 2
exit
interface range gi8,gi16
switchport default-vlan tagged
[code]....
View 6 Replies
View Related
Aug 30, 2011
Our customer use catalyst switch that spanning tree be PVST+ mode.I take SG300 connect with this catalyst switch.Does it support ?If it support,how to config on SG 300 ?
View 1 Replies
View Related
Mar 9, 2012
I have two switch SG300-10 that need to be interconnect togheter with a simple redundant "cable fail safe" configuration.My idea is use the two uplink copper port of the first switch, connected to the two uplink copper port of the second switch.
How to create a working setup configuration? The first setup that i need, is with only one VLAN1 for all ports,
The second setup is with the VLAN1 assigned to the ports 1-2-3-4 of all the two switch, (linked togheter by uplink ports)
and the VLAN2 assigned to the ports 5-6-7-8 always linked togheter with the same uplink ports.
Is possible use the two uplink port at the same time, as cable fail safe? or use a uplink port 1 for the first group and the second uplink port for second group?
I need to use this configuration for audio cobranet transport, and i need to test the correct configuration for the primary and secondary audio stream, if can work togheter on the same VLAN or i need to separate the two stream, from start to the end.
View 1 Replies
View Related
Apr 1, 2012
I have my network with severals SG300 switches.I have one of them like my core switch working in layer 3 mode. With 2 vlans and vlan interfaces to each vlan.Everything is working ok.But now i have to connect one 3com unmanage switch that have host from vlan 1 and 2. How should i connect this switch to my Cisco sg300 switch?
[code]...
View 2 Replies
View Related
Aug 29, 2011
These are our first switches and seems like GUI is lot different than the online. Out intervlan routing is o not working. I am absolutely sure that I setup the switch in L3 mode since it allows me to create mutiple interfaces. I am hoping that this GUI issue is related to interVLAN routing.
Below is the blog I started for InterVlan issue [URL]
This is the link for online simulator and what I see in its IP tab. I know this switch is not SG300. [URL]
This is what I see on our switch.
Our switch version
switchd64684#show version
SW version 1.1.0.73 ( date 19-Jun-2011 time 18:10:49 )
Boot version 1.0.0.4 ( date 08-Apr-2010 time 16:37:57 )
HW version V01
View 1 Replies
View Related
May 26, 2011
1) I have a Cisco SG300-28P. I plan to add a SG300-52. Would it be possible to manage the new switch through the SG300-28P web browser ?
2) There are 2 fans in the POE model SG300-28P. How many fans are they in the non POE switch SG300-52 ?
View 2 Replies
View Related
Feb 8, 2012
Can I connect a single Cat5e cable between two SG300-28 and link them? If so what must I configure?
View 1 Replies
View Related
Jul 25, 2012
I have SG300-28P that I am using as layer-3 switch. Recently I ran in to SG300-52 switch and even though loading same firmware doesn't give me option to do layer-3 switching. For SG-300 I see options in GUI to create vlan interfaces under IP information section, while SG300-52 has IP information option only under the management section.let me know if these are 2 different hardware types and L3 is not possible on SG300-52. If its possible to enable L3 switching on SG300-52?
View 2 Replies
View Related
Nov 21, 2011
I'm replacing 2 3COM 4500 Swithes with the SG300-52 Cisco switch. We have 3 VLANs, 10, 20, 100. The switch is set for Layer 3 and I have setup DHCP relay. what settings i should set on the Cisco for the following setups:
3COM Setup
#
interface GigabitEthernet1/0/1
[Code].....
View 2 Replies
View Related
Jan 1, 2013
We have several of the SG300 Serices switches. We use them to route VLAN traffic to Remote Offices, Internet Connections, and WiFi Access Points.In one remote office we have a SG300-10 setup to route the HQ Network and the remote Office Subnet. The SG300 is Connected to HQ via Fiber and has multiple Tagged VLANs on it. If I do speed tests over the Fiber Link on the Incoming Tagged Netwotk I get Decent performance, 80Mbs. If I switch to a networtk that is not priginating from HQ, and have the SG300-10 route packet, I get dismal performance. 15-20Mbs.
I Fireded up a New SG300-28P FW v1.2.7.76. Added a the HQ VLAN 101 and new VLAN 1025 . Mapped some Tagged and untagged ports for each. Switch was connected to HQ Network as untagged VLAN 101. I put a laptop on an Untagged VLAN 101 port. Ran some tests, cam back with 750-850Mbs. Great. Put the same laptop on a Tagged 101 Port, Configured the NIC for Tagged VLAN 101, Same test, same Speeds, 750-850Mbs.I then Configured laptop for Tagged VLAN 1025. Connected to tagged VLAN 1025 port. Ran speed tests, resuts were 15-20Mbs!
I then Configured laptop for Untagged VLAN 1025. Connected to unagged VLAN 1025 port. Ran speed tests, resuts were 15-20Mbs!It was only the Laptop and the Connection to the HQ net on the SG300-28P. Why is the performance of this unit soooooo poor when it needs to route?Other Switches have FW v1.0.0.27 or FW v1.1.2.0. They have Similar speed issues. All Configured for Layer 3.
View 10 Replies
View Related
Dec 18, 2011
does the SG300 switches can be used with Microsoft NLB in Multicast mode?I know on traditional Catalyst switches you can statically "map" IP's to mac's and then to multiple ports but this doesn't seem to work correctly on the SG switches - it gives an error about the mac not being not Unicast?
View 2 Replies
View Related
Aug 7, 2011
Any snmpset commands to add, modify and delete vlan table entries on SG300-10 switches? I checked url... however this information is apparently only valid for catalysts. The latest firmware is installed and the provided MIB files are used.
View 8 Replies
View Related
Aug 20, 2012
I'm going to have several SG300-28P switches to setup. I'll need to create multiple vlans for data, voice, and wireless traffic. I have the following questions in setting up this configuration:
VLAN 1 Management
VLAN 100 Data
VLAN 200 Wireless
VLAN 300 Voice
1) For managing the switches via IP, will LAN1 be the default management network? Should I create a seperate VLAN for managing the switches?
2) For uplinking the switches together, I plan to trunk a port to connect the switches together. What's the configuration on the trunk port to forward all vlans from one switch to another?
3) On some ports, I want to configure a trunk for two vlans (Data and Voice) where the phone has a pass through for PC. The phone supports tagging for the PC and the VoIP traffic. For example on port 10, would VLAN 100 and 300 be set to tagged?
View 3 Replies
View Related
Jan 19, 2012
I'm having alot of trouble trying to connect more that one LAG between two SG300-52 switches.Basically i have configured both switches with the same vlans. For 2 of the vlans i would like to connect them together between the two switches using LAG. Switch1 has Vlan 5 (ports 1-12) & Vlan 10 (Ports 25-36) with LAG configured on ports 1-2 and ports 25-26. I have setup the second switch identical to the first. But when i connect the LAG's there is no connectivty. If i disconnect one LAG the other starts working.Can you only have i interconnect LAG between switches?
View 1 Replies
View Related
Apr 22, 2012
I have two SG300 serie switches and two Gigabit connection between them. How do I configured these two links to work toghether like a one 2 Gigabit channel?
View 2 Replies
View Related
Aug 4, 2011
In the last month or so I have had to reset my router every 30 min or so this is very annoying and would like to know what could cause the problem.
View 2 Replies
View Related
Aug 19, 2012
We have a 3750x switch with some issues on the arp. Our servers become unreachable for some time, buy when I clear the arp cache, I am able to ping the server again. I have tried adjusting the arp timeout but I don't think doing so would be the permanent solution.
View 9 Replies
View Related
Jul 23, 2012
I'm watching a video streamed from my laptop and the signal is constantly being dropped. I suspect the D-Link DES-105. I have another Ethernet switch on the system as well but it is a Gigabit unmanaged switch from D-Link and has worked well with video streams. I've removed the DES 105 from the circuit and videos play fine. Should I dump to DES-105 for another Gigabit switch? SOme say I have a bad cable somewhere but I have tested all and have not found a problem.
View 2 Replies
View Related
Jul 19, 2012
On my SG300 I set up LAG for the last two ports.
I then plugged them into my SRW224G4P, once I do that I get dropped packets.
I was thinking maybe doing firmware upgrades to both switches?
View 3 Replies
View Related
