Cisco Switching/Routing :: 2960G No LANBase-Routing Feature?
Feb 3, 2013
one of our switches (WS-C2960G-24TC-L). When I try to turn on the lanbase-routing feature using sdm prefer lanbase-routing, it gives me an error (Unknown command). I tried "sdm prefer ?", and lanbase-routing wasn't there (only qos, default and dual IPv4 & IPv6). The switch is running on image C2960-LANBASEK9-M version 12.2(50)SE5.We have another switch (WS-C2960S-24TS-L), running on image C2960S-UNIVERSALK9-M version 12.2(55)SE5, and I can enable lanbase-routing feature. If I upgrade the WS-C2960G-24TC-L to version 12.2(55)SE5, will it be able to do inter-vlan routing? Or is the switch itself totally limited to VLAN configuration only?
View 4 Replies
ADVERTISEMENT
Oct 23, 2011
I have used all the ports on my 24 port 2960G and need to extend it with another 2960G. These switches do not have trunk ports so what is the best way to stack them and have all 5 vlans on both switches.Can I just use a port Channel trunk etherchannel ?
View 7 Replies
View Related
Dec 26, 2011
Cisco let us try a CISCO C3750X- 24T-S Stack (2 switches) ->> IpBase Sofware licence We've 2 Hyper-v 2008 R2 and one SAN Netapp FAS2040 connected via Iscsi.All was working well with this stacks.Hyper-V see Nas Iscsi interface without problem. Even with basic stack config (no Vlan, ect...).Then, after this test period, we bought a C3750X-24T-L stack (2 switches) to replace the stack lent by Cisco.This one is LanBase Software.
With this stack, hyper-v work very bad ! We've got a lot of Iscsi error in the eventvwr.I can't access luns.So, is there a difference between LanBase and IpBase for a iscsi use ?I put the 24T-S config on the 24T-L switch without pb. So config is the same on both stacks...Also i've got a "TestPortAsicLoopback" = "Failed" on the new stack...I've tried with other stack cables. Not better.
View 4 Replies
View Related
Jan 21, 2010
I have the following issue; I am getting a duplex mismatch between a Cisco 2960 TT-L Switch running IOS 12.2(35) LAN Base Image (Gig0/1) and a Cisco 6506 Switch running IOS 12.2(33)SXH Adv IP Services (Gig2/19).
I have tried several combinations of the duplex/speed settings on both sides but the only that works is setting duplex/speed AUTO on the Cisco 2960 which ends up autonegotiating to HALF duplex and 100Mbps.
View 9 Replies
View Related
Jun 14, 2012
i have a cisco catalyst 2960g and for some reason out of the blue, some interfaces go down and then up. It started doing it after a power cycle.
View 1 Replies
View Related
Dec 30, 2011
I have 2960G that in rommon status.I need that the switch work in 0x2102 (regular mode).I don't have a backup to configutratuio in my PC.I do wr before the switch go to rommon (startup config).What to do in order to the switch will be in 0x2102 (regular mode) with the same configuration( before the switch go to rommon)?
View 1 Replies
View Related
Jun 26, 2012
I have a few 24-port Cisco 2960G Switches (model WS-C2960G-24TC-L) that I upgraded to IOS Release 15.0(1)SE2 using the web interface. I am now trying to upgrade those switches with the new release, 15.0(1)SE3, however I seem unable to do it, I have tried this on two switches so far, both have been upgraded to SE2 just a couple months ago or so, and both of them will not accept the SE3 upgrade, basically, I can select the tar file in the web browser and click "Upgrade" but when I do the status never changes from "Loading the tar file to the switch". I have tried multiple times from multiple computers using many different web browsers, including IE6 which is listed as supported. I have let it go for as long as 1.5 hours but to no avail.I also had a few idential switches here that had never been upgarded to SE2, I have had no problems loading SE3 onto them using the same method so it would seem that the tar file I have downloaded is valid.
View 5 Replies
View Related
Oct 24, 2011
I have got a catalyst cisco 2960G series switch and via this switch I want to creat serveral vlans. I am getting a dhcp IP from a router and I want to setup my own vlan networks.
I plugged in the Ethernet cable that came from the dhcp router to port 16 of the cisco switch and configured the ports 1,2 and 3 for vlan 1, 2 and 3
the dhcp router has given me this IP 192.168.10.158 defautl gateway is : 192.168.10.1
when I plug in a PC to port 1 or 2 of the cisco switch I still receiving the IP from range 192.168.10.* but not from the range that I configured for the vlan 1 or 2.
Below is my startup configuration:
no file verify auto
spanning-tree mode pvst
spanning-tree extend system-id
[code].....
View 28 Replies
View Related
Jun 7, 2012
I have a 2960G that I keep on the bench as a work switch. I assigned an IP address to it. The techs have had trouble imaging workstations using GHOST. Do any config changes need to be made to enable multicast to work? Everything is in VLAN1 at this point and the GHOST server is also the DHCP server.
View 1 Replies
View Related
Dec 20, 2011
I got problem with wake on LAN software.. The software unable to ON all pc's remotely if sitting under different vlan. Everything is ok if using the same vlan. Below are the network diagram & switch configuration.
Layer 3 switch Intervlan routing configuration
ip forward-protocol udp 7
!
interface Vlan4
description vlan Client-WOL
ip address 172.22.51.253 255.255.254.0
ip access-group Deny_HTTP_Vlan1 in
ip helper-address 172.20.1.246
[code].....
After configured all the switches with the above setting, the software still cannot wake all the pc's using LAN. Base on sniffing, i can't find UDP port usage by the software. Attached here with print screen from wireshark.
View 7 Replies
View Related
Jun 11, 2013
I recently changed jobs and at the new location we are primarily running Catalyst 2960G series switches with the exception of one 3750. All of the switches are setup in a cluster with the 3750 being the cluster master. My question is what is the benefit of switch clustering? The entire network seems to be a bit over engineered for the our needs and I am hoping to scale it back a bit. For example, the the network was setup with VOIP QoS when there were no plans to even use VOIP. Also what procedures would I want to follow to disable the cluster to avoid any major outages? Assuming there is no real need for a cluster.
View 1 Replies
View Related
Jun 7, 2012
I'm trying to decide what switch to use as a core for 500 users. I'm currently looking at either 2 x 3750X stacks or 2 x 4500s with dual SUPs and PSUs, both options will provide the number of switchports required without the need for additonal access layer swiches. Which switch option is best to go for here? All of our services will be located in our data centre which will be connected using 2 1000Mbps MPLS circuits. I wont need any advanced L3 features and we are not likley to scale over 450 users. Also is it ok to use the dual switch stacks or chassis to provide the collapsed core/access layer or is it best to have a dedicated core (using one of the above options with less switchports) and having a dedicated accesss layer using 2960Gs for example. Our structured cabling terminates in a single comms room so we wont need to distribute switches throughout the office.
View 3 Replies
View Related
Oct 23, 2012
i had made a software upgarde on the switch 2960G series have no any passwords, when I fished the upgrade process after rebooting the device i found it need a UserPw to access device manager. i tried to use the default PW "cisco" but it dosen't work too.. after that i tried the password recovery process to rest the PW, but noway, but now i have addition problem, when i try the cmd orders "flash_init , load_helper , dir flash" to beginning the password recovery process it shows the following:
The system has been interrupted prior to initializing theflash filesystem. The following commands will initializethe flash filesystem, and finish loading the operatingsystem software:
flash_init boot
switch: flash_initInitializing Flash...flashfs[0]: 554 files, 19 directoriesflashfs[0]: 0 orphaned files, 0 orphaned directoriesflashfs[0]: Total bytes: 32514048flashfs[0]: Bytes used: 15540224flashfs[0]: Bytes available: 16973824flashfs[0]: flashfs fsck took 10 seconds....done Initializing Flash.
switch: load_helperUnknown cmd: load_helper
switch: load_helperUnknown cmd: load_helper
switch: load_helperUnknown cmd: load_helper
[code]....
After that the problem updated
because I tried to install the IOS by Xmodem to reload the missing flash file.After finsh the TAR file loading and reboot the switch.......the LEDs of mode and Giga ports are lighted amber and not blinking, i tried many times to follow the steps to connect the switch by the emulator and consol cable by holding mode button and connecting the power cable at same time the device does not work, the switch now still not blinking, now i try to read and understand how can i remove the corrupted files and install a new IOS for this switch?What shall i do.
View 1 Replies
View Related
Jun 21, 2012
I am unable to configure an interface using the "ip igmp filter <profile #>" command on a 2960G running 12.2(58)SE2. The switch allows me to create a profile using the "ip igmp profile <profile #>" global configuration command. It also lets me enable filtering with the global "ip igmp filter" command (which I didn't see in the documentation). But, the command is not accepted when configuring an interface. "ip igmp ?" does not even show "filter" as a valid auto-complete when in configure interface mode, and the command is rejected if I try to enter it.
I verified the command worked on a much earlier version of IOS, so it must have broken somewhere along the line. I'm wary of moving up to 15.0(1)SE. Is that a major IOS change?
View 5 Replies
View Related
Jun 20, 2012
I have a Cisco 2960G switch and one of the ports was configured with srr-queue bandwidth limit 90 - I need to remove this bandwidth limiting from this interface. [code]
View 2 Replies
View Related
Dec 5, 2011
I have a requirement to monitor downstream data feed from a remote site and feed it to multiple destination devices for recording. The source data will be fed into a port on a Cisco 2960G switch then, using the monitor function, be forwarded to multiple interfaces. This works fine for normal Etherent II traffic. We tried a test using a device that generates IEEE 802.3 Raw packets ('type' field is used as a 'length' field) but found that while the traffic appeared to be accepted by the input port with no errors it was not forwarded to the destination ports, even when using the monitor function. I did try the 'encapsulation replicate' feature with no luck. It does not forward these packets even if I set all the ports into a common VLAN and let the switch just perform a normal switch function (non monitor).
if it is possible to get the IEEE 802.3 raw packets to pass through the switch and if it is, how to or what I need to do to make it work?
View 13 Replies
View Related
Jul 24, 2012
My Cisco Catalyst 2960G-24TC-L is broken.Yes,I think it's broken.
1.Always dispaly : “ !!! WARNING: The switch is not usable !!! ” “Unable to create l2trace server process, socket_open() failed”.
2.All GigabitEthernet is missing .
Switch(config)#interface ?
Async Async interface
Auto-Template Auto-Template interface
[Code].....
View 5 Replies
View Related
Mar 27, 2012
Our database server is connected on cisco swich 2960G gigabitEthernet 0/38.while showing the interface command the total output drops is a large value..Is there any issue with this value.I think this is one of the reason for slow access of the server.
cisco6#show interfaces gigabitEthernet 0/38
GigabitEthernet0/38 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is 58bc.2746.45a6 (bia 58bc.2746.45a6)
[Code].....
View 5 Replies
View Related
Aug 8, 2012
Multicasting. The configuration is I have a 6506 as my core switch receiving multicasts from an interface assigned to VLAN10. I have a monitor port setup with a PC running Observer which says multicasts are being received on the core switch. On a different interface on the core switch I have a 2960G switch connected to it and this interface is on VLAN 10. The 2960G switch has a workstation connected to it that needs to receive the multicasts. How do I configure the 6506 and/or the 2960G to process the multicast traffic?
View 0 Replies
View Related
Mar 25, 2013
i have 2 no of 3560G in our core, now my requirement is to establish the redunent network like for the edge 2960G using stack or some other way ...
View 6 Replies
View Related
Jul 5, 2012
We run a network of several 2960G and 3650G switches in a network with a number of VLANs. One one particular VLAN (let's call it VLAN 10) it appears that non-broadcast traffic (i.e. normal unicast traffic) is being copied to every port in VLAN 10 only on one switch . The traffic is not crossing trunk ports and does not appear on other switches that have ports in VLAN 10. We first spotted this by noticing that a UPS port had an unusual amount of activity on our port througput graphs:
This traffic at 4 am is not expected and this profile is repeated across all ports in VLAN 10 on this switch (a WS-C2960S-48TD-L stack running IOS 15.0(1)SE3)\iffed one port using local SPAN (the UPS port) and discovered that this traffic was not broadcast, which was running at a normal low rate at all times. The traffic appeared to be unicast traffic from other ports of the sort you might see on a hub. It was from various hosts that live on VLAN 10, most (not all) of the conversations had one end station homed on the 'problem' switch. There are about 800 non-broadcast packets per hour and this is a busy VLAN so it does not account for all the traffic on the VLAN.
View 3 Replies
View Related
Jul 4, 2012
I am unable to access a series of switches connected together through a management vlan. I receive the message "The server xx.xx.xx.xx at level_15_access requires a username and password." Entering the username and password fails and the same username and password message returns. I am able to ssh into the switch with the username and password that fails trying to access the switch with the browser.
How can I check the username and password for access with the browser?
I am trying to monitor switch performance. Is there a good way to monitor switch performance with the command line interface?
View 2 Replies
View Related
Feb 11, 2013
I just got a Cisco 2960G 24-port gigabit switch so that our HP servers can have a Gigabit connection to the network. I moved 2 servers to it (HP Proliant DL380's) but they don't actually seem to be able to achieve even close to 1000Gbps. I ran same some LAN bandwidth tests and it was showing only around 200-300 Mbps between all of them. I also ran a network stress test utility, LAN Tornado, and it was showing packet loss as high as 60% when on gigabit, and only .07% when on 100Mbps.
-Both the NIC's and the switch ports are set to 1000/Full
-Currently using Cat5e cabling no more than 25Ft in length (I know Cat6 would be better but Cat5e is supposed to support Gigabit)
-All servers are on the same VLAN
Here are the port statistics when running just a stress test @ 10Mbps that had a 45% packet loss. What's odd though is when I set the servers and switches to 100Mbps, I get less than 1% packet loss.
GigabitEthernet1/0/16 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is 203a.07ff.7e90 (bia 203a.07ff.7e90)
MTU 9000 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
[Code].....
View 2 Replies
View Related
Feb 25, 2013
I had a bad power surge yesterday that took out a 2960g switch and the APC UPS that it was connected too. when plugged in the fan comes on and the syst light stays amber and the rps, stat, duplex. and speed light stay lit and the port lights for ports 21-24 stay lit. plugging it into the console on boot I cant even see rommon, so i dont think its even booting. I would like to find a pinout and voltage guide for the connector comming off the power supply so I can check the voltages coming off the power supply to tell if it is a bad PSU or if it took out the main board.
View 2 Replies
View Related
May 22, 2013
I have a query regarding attached Network Design
PC---2960---3750(One Routed Port and All Switched Port)------------------------ 3750(One Routed Port and All Switched Port)-----2960------Internet
I have many Vlans on left side of image , Right Side of Image is having internet connection via Modem, and local connectivity between VLAN works fine but Other Vlans Except Vlan1 is able to Access Internet.Note that 3750X did not have NAT Feature ,How should I able to get Internet on Other Vlans (10,20)
View 4 Replies
View Related
Oct 18, 2011
I am facing an isssues with 7609 for LAN switching , based on LAN (VRRP/HSRP) feature.Actually we are having ES+ cards (on 7609) and we are using multiple groups(say 350 vrrp groups) running on the router . the routers are connected as router 1>>> mux(which is working as switches)>>> router2
my questing are
1. does their will be "multicast packets" (for VRRP/HSRP group) "from backup router to Master router", when in stable state( ie when Master and backup are already chosen) , or the packet from backup to master should be unicast.I know for sure, the packet from master to back is multicast packets denstination to Multicast IP packet and To MAC address.I am not sure but I think from backup to master it should be multicast
2. what is frequency of these packets( from backup to master)
3. As i have multiper group on a single interface ( we are using q-in-q), when the connectivity from router's is broken, then does all the groups will muticast their active roll in the lan sengment "at once" or it will be in a groups say 100 groups at once, and after few ms few 100's and sone ( as is on OSPF or RIP)
we are in between troubleshooting I hope we get the ans( Actul problem we are seeing in the router's that we have 2 ports on active routers and 2 ports on standby router , but we are not seeing muticast on 1 port on standby router where as all other 3 ports are seeing multicast packets) [code]
View 5 Replies
View Related
Oct 26, 2011
I have been looking to find out the list of features that the IP Base IOS has for the 3750X series switch. What would be ideal is a comparable list but essentially I need to know which of the LAN Base/IP Base/IP Services has SSH functionality.
View 1 Replies
View Related
Sep 9, 2012
Full feature set for IP Base with the 3750x.I just wanted to verify that I could create a routed port, turn ip routing on, and create static routes as well as a default route. From what I can find, there shouldn't be a problem with this on the IP Base Feature Set, I just wanted to verify. Or any link for the Features of IP Base on the 3750x.
View 3 Replies
View Related
Jul 22, 2012
We are going to be rolling the 4500 switches out and I wanted to know more about how to use the wireshark featue. Any documentation on how to use this?
View 2 Replies
View Related
Oct 12, 2006
Had problems with voice quality on VoIP with 4500 series switches and the qos dbl feature (which gets enabled by the auto qos feature)?? I have had a couple of customer complaining about voice quality and our voice team spent a lot of time investigating; I had ruled out the network infrastructure because it was all QOS enabled. The voip people came up against a blank so I looked at the network once more and disbaled dbl with hope more than anything else. Mysteriously the voice quality issues the customer was having have now disappeared. Not sure whether a coincidence (though I have done this on two customers now) or something to with with dbl. There is nothing on this on cco.
View 3 Replies
View Related
Dec 13, 2011
I've a 3750-48ps-s running ios version: c3750-advipservicesk9-mz.122-46.SE.bin
I've tried to configure ipv6 on an interface but it does not give me the option.
How do I know if my ios is IPv6 capable?
View 1 Replies
View Related
Dec 19, 2012
i want to know of the IOS verstion of cisco switch which support STP,some one told me that this feature is activated by deafalut if it not activated,how to turn on this Feature.i am using cisco 2960 Switch.
View 2 Replies
View Related
Jan 7, 2013
I have a 2911 router with 15.1(4) Ios Version. I need to enable the evaluation sna feature but when I try to enter the command "license feature snasw" but I get an error, the command "License feature" does not exist.
View 3 Replies
View Related
