I have a 3750G switch in my production network that only has VLAN 1 on it. All ports are in a default state and VLAN 1 is disabled. The switch is passing traffic but shouldn't having the default VLAN shut down cause the ports not to pass traffic? If I start to create VLANs will that cause the switch to stop passing traffic?
View 4 RepliesWe have 3 VLAN in our cisco 3750G switch. VLAN 1 10.1.0.0/24 for domain network, VLAN 2 10.2.0.0/24 for student and VLAN 3 10.3.0.0/24 for public. We have one printer 10.3.0.206 in the VLAN 3 and want to allow student server 10.2.0.253 in the VLAN 2 to access the printer. How can we configure access-list? Here is current configuration.
ip access-list extended publicaccess
permit icmp any any
permit ip any host 10.2.0.253
permit tcp any any established log
deny ip 10.3.0.0 0.0.0.255 10.1.0.0 0.0.0.255
deny ip 10.3.0.0 0.0.0.255 10.2.0.0 0.0.0.255
Between our hosting and a customer we have an extended vlan, traveling on a fiber, between two cisco 3560 switches.The thing is, that we want to create one or more vlans inside that extended vlan, in some way if possible?
View 3 Replies View RelatedI have two networks at two sites with a dot1q trunk between the two L3 switches at both sites (no routers involved)
SITE A - Cisco 3750 L3 - VLAN ID 50
10.10.50.0/24
SITE B - Cisco 3750 L3 - VLAN ID 50
10.20.50.0/24
I would like to extend the SITE A VLAN to SITE B so that I can move hosts from SITE A to SITE B without needing to change their IP address but the vlan ID is already in use. Obviously the easy solution is to change the VLAN ID for one or other of the sites but both sites contain hosts that run 24/7. Is there a way to join two VLANs with different IDs together.So for example I create a new VLAN 60 at SITE B and associate it with VLAN 50 at SITE A.
i need to solves this little problem on 2960S lan BASE but i dont know if it is possible.
Uplink port config for gi 1/0/28 is:
switchport mode trunk
switchport trunk alloved vlan 10,11
but on interface gi 1/0/1 i want to have data from vlan 10 tagged as VLAN 20.
At this time i have solved this issue very primitively
I have set up gi 1/0/2 as int mode acces, acces vlan 20 and i have connected gi 1/0/2 with gi 1/0/3 with eth cable. int gi 1/0/3 is switchpor mode acces, switchport acces vlan 10
I am trying to setup a L2tpv3 VLAN-to-VLAN tunnel.My setup has two Cisco 890 router with Cisco IOS Software version 15.0(1) M4. These routers are connected directly on FastEthernet port 8.
One linux machine is connected on FastEthernet port 0 on each router. The two linux machines are on same vlan. I am trying to establish a vlan-to-vlan tunnel between the routers and send traffic between the linux machines.
I followed the case study 11.4 from [URL] and configured the l2tp-class and pseudowire-class. However, the vlan interface configuration is different on 890 router.
I configured a vlan interface as follows.
(config)#vlan 200
(config)# interface FastEthernet 0
#shutdown
#switchport access vlan 200
(config)# interface vlan 200
I don't see the 'xconnect' command in this context. What's wrong with my configuration?
We have a low bandwith (15-20 Mbit/s) to the ASA from our Client vlan. If i connect the Client to the same vlan as the ASA is, the bandwith (90 Mbit/s) is good.
Here are the Layer 3 Design:
Client -> vlan 2 - Switch - vlan 7 -> vlan 1 - ASA 5505 -> ISP
The Layer 2 Design:
Client -> Gig2/0/13 - Switch - Gig4/0/43 -> Eth0/1 ASA5505 -> ISP
IP Address:
Client: 172.16.2.10Vlan2: 172.16.2.1Vlan7: 172.16.7.1ASA: 172.16.7.2
I assuming the switch has a problem with routing ?It is a stacked Switch with following members:
switch 1 provision ws-c3750g-12sswitch 2 provision ws-c3750g-24tsswitch 3 provision ws-c3750g-24tsswitch 4 provision ws-c3750x-48
And we have following error message in the log from the switch:
%PLATFORM_UCAST-4-PREFIX:
One or more specific prefixes could not be programmed into TCAM and are being covered by a less specific prefix, and the packets may be software forwarded I first get the idea that the switch is overloaded with router traffic. Thats why i assuming i have to check the sdm templates, but i'm not sure if this resolves the issue.
Here are the relevant config:
ASA Interface on the Switch:
interface GigabitEthernet4/0/43description ASA-inside LANswitchport access vlan 7switchport mode accessspanning-tree portfast
Client Interface on the Switch:
interface GigabitEthernet3/0/1switchport access vlan 2switchport mode accessswitchport port-securityswitchport port-security aging time 2switchport port-security violation restrictswitchport port-security aging type inactivitymacro description cisco-desktopspanning-tree portfastspanning-tree bpduguard enable
[code]...
I have an RVS4000 version 1 with firmware 1.3.3.5. I have two VLAN's setup:
VLAN1 - 192.168.1.0/255.255.255.0
VLAN10 - 192.168.10.0/255.255.255.0
Ports 1 through 3 are configured for VLAN1 and right now I have one PC connected directly to port 1 and nothing connected to ports 2 or 3. Port 4 is configured for VLAN10 with a managed switch (also configured on VLAN10) connected to it. There are 4 wireless access points connected to the switch.
On the Setup->Advanced Routing page of the RVS4000 I have the Inter-VLAN Routing option set to Disabled. Yet when I connect to one of the wireless access points and receive a 192.168.10.x address, I can ping the PC connected to port 1 which has a 192.168.1.x address.
Also, I would like VLAN10 to not have access to the Management GUI on the RVS4000.
I'm creating 3 vlans, one private ip addresses and the two for two blocks of public ips. After creating them devices on the same network are able to talk to each other on the private IP but not on the public ips.
View 1 Replies View RelatedI am currently tasked with setting up a network, pretty much from scratch, that requires some fairly hefty VLAN deployment. My hardware on hand (already existed so can't can't change anything easily) 5x ESW-540-48 Switches, 1x3750g switch, 1x2811 router. I don't believe the router should be required as the 3750 is capable of intervlan routing. [code]
Now at one point I actually had the VLAN's *working* in that I could specify an IP address and could ping to and from it! However DHCP wasn't passing despite numerous attempts with DHCP relay and IP-Helper configurations.Also I was having issues with VLAN 1 as the native VLAN, the ESW switches don't allow you to do much with them, as they 'weren't created by the user'. So tried switching that out to VLAN11 also but with very little success there (I had to change the native vlan on all trunks to VLAN 11)All the 10.x.x.x addresses need to be able to communicate with each other.All the ESW switches need to be able to handle their respective VLAN's as well as VLAN 1 (for Printers and wireless access points distributed around the building).
We have a server that we remove from the rack. The only role it has is to give out DHCP on the wireless network. I tried enabling the built in DHCP server on the Airespace 4112, though a Catalyst 3750G, but I dont get an address when I'm connected to the wireless network even though the range is enabled. If I set an static IP on my wireless card I can access the network. I also tried enabling DHCP on a Sonicwall that is connected to the Catalyst 3750G.
Do I need to link the DHCP scope to the wireless network? Is there anything on the switch that would be blocking DCHP since it on a VLAN? I have the last four ports in a VLAN for the AP's and the internet connection to the Sonciwall.
i'm going mad on following problem. I'm trying to get 2 networks seeing each other while one of the network is a non VLAN network and the other one is a VLAN network.They should use the same interface so i added VLAN e0/0.122 to the interface e0/0.Send a ping from my asa to both gw-IP's made me happy at first. In second in figured out that i cannot reach any client in the other network. For testing purpose i created an permit acl to any/any for both networks, but the packets still get dropped by the default implicit rule. (deny any/anyMaybe i'm to stupid for this
View 10 Replies View RelatedThere are 5 VLAN's and all can communicate through all the different subnets, but VLAN5 can not communicate to the RVS 4000.
VLAN Smart Port set to switch and router - this is not working What Smart Port configuration should be set up to talk to the LAN port on a RVS4000?
VPN is set up and connected, but when trying to connect to the client can not connect to remote networks.
Has any come across show ver memory details on 3750G-48PS as below, One of our Catalyst 3750G running software 12.2(44)SE2 shows unexpected DRAM as below:
cisco WS-C3750G-48PS (PowerPC405) processor (revision F0) with 0K/12280K bytes of memory. This would equate to around 11MB memory which does not seem right... Is it a known IOS bug?
Before I implement the VLAN setup I have configured I want to make sure I did all of it correctly.
Router SG300 L3 Router 192.168.0.93
VLAN10 - Servers
VLAN20 - Building B FOH - 192.168.2.1
VLAN30 - Building B BOH - 192.168.3.1
VLAN40 - Building A - 192.168.4.1
Port 24 - 28 Set as Tagged VLAN 10,20,30,40
#
Port 24 Internet Traffic
Port 25 Switch 1 Building B
Port 26 Switch 2 Building B
Port 27 Switch 3 Building B
Port 28 Switch 4 Building A
On the Sonic wall I have a static route for the 192.168.2.0, 192.168.3.0 and 192.168.4.0 networks going back to the 192.168.0.93 Router. All the Switches on the up link port are set to trunk with tagged VLAN 10, 20, 30 & 40 setup. On each port for each switch I have the ports untagged to the VLAN the devices should be on.
I have setup a DHCP relay to the DHCP server and associated each interface 192.168.2.0, 192.168.3.0 and 192.168.4.0 . Am I missing anything else? Did I do this correctly?
In my company we are re-arranging the network and the servers, and a consultant is insisting to split our network to three V-lans using cisco SF 300-48P 48-Port 10/100 PoE Managed layer 3 switch as this:
1- Forefront TMG server
2- DC(AD,DNS,DHCP), ERP, File, servers
3- the rest of our workstations
i used the web access page to configure the vlan's but i couldn't find a way to assign IP address to Vlan port i searched a lot and read a lot of the posts and they mentioned changing the switch mode to layer 3URL
DHCP = win2008r2
scope 1:
172.16.1.51 - 172.16.1.200
sub net 255.255.255.0
router: 172.16.1.1
scope 2
172.16.3.51 - 172.16.3.200
Sub net 255.255.255.0
router: 172.16.3.1
Nic1 = 172.16.1.20
Nic2 = 172.16.3.20
[Code] ......
Coincidentally when i tried to configure router 877 as an adsl router i found that a vlan configuration is included. my question is what is the benefit of using vlans in router ??? i studied that we use it in switches for the purpose of network enhancment from broadcasts and netwrok segmentation. why we use vlans in routers ?
View 9 Replies View Relatedwhat the difference between L2 Vs L3 VLAN? in know in which situation i use L2 Vlans but i don't know that about L3 Vlan.
View 2 Replies View RelatedIm planning for a network upgrade.77.110.87.112/28 - is assigned to selected users and configured manually.(note: they are public IP which our ISP assigned)192.168.1.0/24 - is assigned to users that are not allowed to use internet services and configured manually. I have CISCO 1841 Router connected to the internet and CISCO SGE2000-G5 24ports layer 3 switch that is connected to cisco 1841 router.i want to create vlan in layer 3 switch. [code] i want all vlans would still ping to each other and file/printer sharing is available.kindly check if my network upgrade plan is correct, how am i going to configure those vlan in my layer 3 switch and to connect to the internet.
View 12 Replies View RelatedI have a customer who is on thr 192.168.254.x subnet and is using a Cisco 881 as their gateway.
They wish to create a second VLAN for the 192.168.253.x subnet.
The Cisco has Dialer0 configured for an ADSL connection.
I have partly configured the router but need some info regarding router a device on the 192.168.253.x subnet to the internet.
configure routing to the internet on the new VLAN and assist in setting up a DHCP server on that vlan. I have attached a copy of the current config.
I have a 3560-8PC in which the mgt vlan randomly (twice in one day or 2 weeks later) goes into the down state and will return w/o any interventaion 15-20 minutes later. Int G0/1 is the uplink to a 3750. I dont think its a layer1 issue at this time since i have seen it work just fine for over 2 weeks and drop again. I don't see any errors on the 3750 either.
WS-C3560-8PC 15.0(2)SE C3560-IPBASEK9-M
LOG:
----------------------------------------
.Oct 20 19:34:37.533 EDT: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changeds tate to up
[Code].....
I was reading a QoS walkthrough earlier to try to solve my problem and I noticed that in IOS, you can specify "match vlan" in a class map. This is not available in NX-OS. I'm not doing any routing on the 5K so I cannot match on ACL, and port where traffic is received is a trunk sharing other types of traffic I'd like to classify elsewise.
How can I match traffic on a per-VLAN basis?
I have the Cisco Router 861 whit the IOS c860-universalk9-mz.150-1.M7.bin. I have created a Vlan, but when I create a second vlan, I have this message: "Vlan can not be added. Maximum number of 2 vlan(s) in the database.
I need to add more than two vlan.
In my network i have two 6509s connected with L3 etherchannel. i have created saparate vlans in the two 6509s with different switches.now i want to use one vlan in 1st 6509 in the 2nd 6509 how can i use ...
View 1 Replies View RelatedI have a couple of Nexus 5ks that I want to put QOS on for the servers running behind it but also have voice running across it. Voice doesn't play well with jumbo frames so I'd like to put QOS only on the voice vlan.
View 1 Replies View RelatedWhy I got below error message when config Private VLAN?
Error: while enabling/disabling service: private-vlan, err: Private-vlan is not allowed in F2 VDC (0x40e4005d)
I am working in my lab and I was adding a new L2/3 vlan
vlan 555
name test
int vlan 555
ip address 1.1.1.1/24
no shut
I have also ensured that this vlan is added to the port channel going to my Nexus5K's. I added the vlan to the 5K's and also ensured that vlan 555 is traversing the peer link. all is good there. I have also placed a device on a interface on the 2k as a access switchport on vlan 555
Here is my problem, the L3 interface will NOT come up on the 7K
LAB-DSW01# sh ip int brie
IP Interface Status for VRF "default"(1)
Interface IP Address Interface Status
Vlan555 1.1.1.1 protocol-down/link-down/admin-up
I have gone throug just about everything I can think of and I am still unable to get this L3 interface to come up. I have other L3 interfaces on this device that are configured exactly the sameway without any issue at all. All the existing interfaces are working properly, it's jut this new interface that I am trying to add.
I am running version 6.0.1 on the 7K and 5.2.1.N1.4 on the 5K.
Any "best practices" or recommendations on how to migrate from a fixed router (3745) to vlan routing on Catalyst 4507 switches in order to minimize the disruption to the network.
View 4 Replies View RelatedI have a network with a Catalyst 3750 as the main switch and then some Catalyst 2960 switches that are plugged in to that. I have a server running windows server 2008 with a couple of virtual machines running in Hyper-V. I created 4 VLANS listed below and gave the 3750 the following IP Address.I would like the 3750 to only be configurable from VLAN 40 but currently every VLAN can connect to it, I noticed in the standard web page settings there was a setting for "Management VLAN" but it was set to 1 and would not let me change it, I kinda assumed that was for the management port in the back.-Now the tricky part, I was trying to set up routing between the VLANs and so far I have only been able to get a sort of "all or nothing" routing to work. I can turn IP routing on and add two or more VLANs to the routing and it works fine. But what I was hoping to do is create a couple of "junction vlans" that would only route to one or two other vlans. For instance, I wanted to create a VLAN 100 that routed to VLAN 20 and 30 but nothing else. I also want to route VLAN 1 just to VLAN 30, and so on. I am able to do each one of the cases but only one, it seems like the switch only supports one "routing table" am I missing something or is this just a limitation of the switch?
View 2 Replies View RelatedI have a network with several catalyst 2960 switches and one catalyst 3750. I have created two VLAN and set up the proper routing and everything is working fine there. I have a client/server application that used multicast in the initial start up for the client to determine available servers, the issue is one of my clients is on a different VLAN then the server. I am able to route the multicast using MVR as long as both the server and the client are plugged into the 3750 by creating a static route, making the server a source port and the client a receive port. Unfortunately I need the client and the server plugged in to different 2960s. My question is how do I establish multicast routing between the two and perferably do it dynamically (always route multicast traffic from one VLAN to another).
View 2 Replies View RelatedDoes Catalyst 3550 switch support inter vlan routing ?
View 12 Replies View RelatedI have a DC topology based on 2 layers, access and aggregation, based on 2 pairs of N5548Ps, both without L3 Daugher Cards. My intent is to use the aggregation N5K pair as L3 inter VLAN layer, so I configured all the VLAN default GWs there. The 2 layers are interconnected via vPC, in a double-sided vPC topology for some N2Ks and some vSwitches. The point is that, despite connecitivity is working fairly ok, for some applications, like file transfer via either FTP or HTTP, between hosts in different VLANs, the performance is too poor. The file transfer starts ok, but after a while it becomes lower and lower. ICMP is working, but I can see some strange random behaviour, like having some packets taking more that 20 ms (sometimes 40 or more), whilst average is 2 ms.
I read through some articles saying that until you don´t have the L3 license (the one coming with L3 Daughter Cards) you can expect some weird behaviour on L3 level. Is that true?. What can I do apart of purchasing L3 Daughter Cards?. Can I enable L3 Basic license at the moment (I don´t need dynamic routing for now).
Here some excerpts of what I´m saying:
PING results:
10000 packets transmitted, 10000 packets received, 0.00% packet loss
round-trip min/avg/max = 0.809/2.496/57.559 ms
System version: 5.0(3)N2(1)
License and features on the N5Ks:
switch# sho license usage
Feature Ins Lic Status Expiry Date Comments
Count
--------------------------------------------------------------------------------
FCOE_NPV_PKG No - Unused -
FM_SERVER_PKG No - Unused -
ENTERPRISE_PKG No - Unused -
[code]....