Cisco Switching/Routing :: 3750e InterVLan With RVS4000 Gateway
Jan 4, 2012
I have a RVS4000 connected to my cable modem which I use as my gateway, the IP address of the RVS is 192.168.3.254
I have a 2811 with 3 subinterfaces of which I can ping all of them from my PC which at the minute is in VLAN 1, the only network that can connect to the outside world is VLAN 1, how can I enable the other 2 vlans to connect to the internet?
My set-up details are
Router
interface FastEthernet0/0.1
description *** Data Network***
encapsulation dot1Q 1 native
[Code]....
View 1 Replies
ADVERTISEMENT
Oct 17, 2011
Can I have use a Gateway-to-Gateway IPSec tunnel whereby a user can surf the Internet using his local Internet connection and at the same time connect through the IPSec tunnel to a remote subnet using RVS4000 routers?
View 1 Replies
View Related
Dec 8, 2012
I need to use cisco 3750E switch on core. I want to know whether BGP is supported on this model or not?Currently i have c3750e-universalk9-mz.150-2.SE/c3750e-universalk9-mz.150-2.SE.bin" preinstalled. and i checked BGP is not supported on this IOS image.
View 7 Replies
View Related
Jul 4, 2012
upgrading our small office network. We currently have about 75 employees with probably 125 devices on the network. I'd like to create about 10 vlans for the different departments and then configure intervlan routing as needed. Currently we have all unmanaged switches and it's just a huge broadcast storm on the network. We are upgrading our Cisco 800 router to an ASA5505 sec. Plus license. I need some recommendations on switches. Of course, this needs to be done as cheap as possible.... Is there a way to use the ASA to configure all the vlans and intervlan routing and access lists and use a cheaper switch to provide the access layer to hosts?
View 4 Replies
View Related
Mar 12, 2013
Quick question here. Using 3750E series switches with multiple VLANS configured. These switches serve as our 'core'. I have SVIs configured for the different VLANs and add inbound ACLs in each of the SVIs to control traffic between VLANS. This switch also terminates a P2P Ethernet link which connects to our Colo facility. The port used for this is configured as an L3 port. I noticed today that I was able to send traffic across this L3 link that I thought should have been blocked by an ACL I had in place but it wasn't. So the traffic flowed from a port in say VLAN 20 across this L3 link (assigned with an IP address). Would this traffic flow not cause traffic to be checked against an ACL applied in the inbound direction on the SVI of VLAN 20 (int vlan 20)? Traffic does get checked when routing between SVIs. Why would it not get checked when routing between SVI and L3 interface?
View 2 Replies
View Related
Aug 5, 2012
I'm trying to configure intervlan routing between a cisco 2801 router and HP/Amer switches. Using int fa0/1 and subinterfaces I was sure I had it configured correctly, but I cannot ping the default gateways when I place a host in a particular vlan. Below is what I have configured.
HP switch - port 9 connects to fa0/1 on 2801
ip default-gateway 10.1.100.1
trunk 9 Trk1 trunk
trunk 10 Trk2 trunk - to another switch
[code].....
View 4 Replies
View Related
Nov 21, 2012
I am using a 3750 as a default gateway for multiple Vlans on a few 2960 switches. The trunk lines are configured and working and I have assigned ip addresses to each of the Vlan interfaces on the 3750. My issue is that I can only ping the ip address on the Vlan interface of the 3750 if I have a working computer plugged directly into the Vlan on the 3750. I only have 3 vlans on the 3750 that have hosts directly connected (vlans 2, 10 and 40) the other vlans ( 20 and 70) don't have any clients plugged into them on the 3750 but the hosts reside on 2 different 2960s that connect via trunk ports. How do I keep the vlan interface on the 3750 switch pingable when I don't have hosts directly connected in that vlan on the 3750? (yes, I have enabled ip routing on the 3750)
View 5 Replies
View Related
Apr 16, 2012
I have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net. My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20,I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2),my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to,go out to the internet.
View 3 Replies
View Related
Dec 11, 2012
I implemented access list on cisco 3560 switch but it never works. I want to block access from network B to Network A and allow from Ato B
Network A. 10.0.12.0/24
Network B 10.0.24.0/24
The configuration is
interface Vlan1
description Data VLAN
[Code].....
View 14 Replies
View Related
Sep 5, 2012
On cisco and am having some issues with intervlan routing. I have followed the vids and manuals but just can seem to get this working. I have the following network lab set up.
Vlan 10 = 10.70.1.9/24
Vlan 20 = 192.168.0.1/24
ME2400 firmware
ROM: Bootstrap program is ME340x boot loader
BOOTLDR: ME340x Boot Loader (ME340x-HBOOT-M) Version 12.2(35r)SE3, RELEASE SOFTWARE (fc1)
[Code]...
View 4 Replies
View Related
Jan 31, 2013
I am in the process of upgrading our network switches and wondering if the .lic file will work with the new software or if I have to rehost for the move to 15.0. Its a remote site and I would like to get some solid info before I pull the trigger.
Also which IOS should I be upgrading to?
c3750e-ipbasek9-mz.150-2.SE.bin
or
c3750e-universalk9-mz.150-2.SE.bin
[Code].....
View 2 Replies
View Related
May 22, 2013
my company pay a switch 3750 X. WS-C3750X-24T-E. It uses IP services basically but I failed to configure InterVLAN routing. why interVLAN routing doesn't work on my switch?
View 10 Replies
View Related
Dec 2, 2011
I've been working with these two Cisco devices in my home off and on for several months now but I just can't take it anymore, I'm about to throw them away and go back to Linksys router.
I have a Cisco 2600 Router with only one Ethernet card in it so I have to trunk from my 3550 Switch to that device. I'd like to have my ISP and all users plug into switch and all trunk back to the router's sub interfaces. Currently, I have started over...again, and am unable to simply get the router and switch to ping each other if I put sub-interfaces on the router. See my configs:
2600 ROUTER:
Router#sho run
Building configuration...
Current configuration : 555 bytes
[code]......
3550 SWITCH:
Switch#sho run
Building configuration...
Current configuration : 2302 bytes
!
version 12.2
[code]..........
Port F0/24 is in VLAN 1, as are all ports but Port F0/1 which is my desktop PC. I mocked it up in Packet Tracer and it works just fine. This is just a simple setup and I'm making sure I can ping between switch and router before I move to each next step.
View 40 Replies
View Related
Nov 20, 2012
have 2 3750's one is an 3750E the other one is a G... Since they are 2 different versions Do I need to correct ios for each for example my 3750E switch i would have
IP BASE
c3750e-ipbasek9-mz.122-53.SE2.bin and for my 3750G switch should i use
IP BASE
c3750-ipbasek9-mz.122-53.SE2.bin
Which would be 2 separate images
View 4 Replies
View Related
Nov 13, 2011
Can I get a stack cable longer then 3m?
View 1 Replies
View Related
Apr 4, 2011
We're seeing "OutDiscard" error on a LAN switch connected to newly migrated Cisco IP phones. All the other error counters are clean except for the OutDiscard. (please see attached "show int count err" output.) [URL].
According to the link above, the common cause of such discards can be to free up buffer space.(Am I seeing a switch buffer issue?) How to identify/resolve the cause of the OutDiscard.The switch is 3750-E running c3750e-universalk9-mz.122-44.SE6.bin
View 1 Replies
View Related
Apr 16, 2012
I am seeing on my 3750E series switches (WS-C3750E-48TD). I have multiple VLANs configured on here, one which is used as a 'workstation' VLAN. I have an inbound ACL applied to the VLAN interface *(int vlan 50 to be exact). This list is admittedly long at roughly 6000 ACE's. Now I just recently installed these switches as they replaced some 4507R switches which we moved to our new centralized DC. Here is the issue I am having. This same ACL was applied to the same VLAN interface on the 4507s when they were doing the work of the 3750s. What I used to be able to do was actually edit the ACL by removing it with no ip access-list extended WS-In and then followed up by the ip access-list extended WS-In ......and the lines I wanted in the ACL. I know I could use the line numbers to edit the ACL but this worked OK for me. When I would do this on the 4507R, the ACL was still applied to the interface but traffic never seemed affected by the removal and re-adding of the ACL. I did this by copying and pasting the ACL into a terminal window. It seemed as though on the 4507 the ACL was not compiled until the entire thing was in loaded in and therefore traffic was not processed by the ACL until the load was done
View 3 Replies
View Related
Oct 30, 2011
I have a 3750E stackable swtch and I need to configure neflow on it. Are there any IOS versions that support netflow on the 3750E? Is there any possible to configure netflow on a 3750E? I do not see any netflow commands available on the switch?
View 2 Replies
View Related
Oct 18, 2011
i have 2960 l2 switch connected to the ASA 5505. for some or the other reason i am not able to do intervlan communication. have done trunk mode on both ends on the switch as well as on the ASA and native vlan 1 allowed. the trunk is up up i am able to ping only the vlan 1 ip from the switch to the ASA for the vlan 2 i am not and similar for vlan 3.
config on the ASA
ASA Version 8.2(1)
!
hostname ciscoasa
[Code].....
View 2 Replies
View Related
Apr 11, 2012
what is difference between Cisco catalyst 3750e 48 and SF300-48p.
View 3 Replies
View Related
Feb 11, 2013
How do i enable InterVLAN MultiCasting. I have a WS-C3560G-24TS as my core switch and it does InterVLAN Routing. I have a Server VLAN (70) and Workstation VLAN (71). I have a server that i have set up to deploy images to computers. Up to this point i have only done one computer at a time, so unicasting was ok. I would like to be able to Multicast to multiple computers, but am unsure what i need to do on the switch (if anything) to enable this.
View 2 Replies
View Related
Aug 29, 2012
We are trying to figure out how to configure this properly and so far we are stuck. We have a VMWare server with two different vmnics each on a different VLAN. We have each of these vmnics connected into their own switch port on a 3560G along with the appropriate VLAN membership for said ports. We have an additional port on this same switch in trunking mode connected to our firewall to a NIC that has an IP address in the respective VLAN networks. This port is also set for dot1q encapsulation. Each VLAN also has an IP set on the switch that is in the appropriate VLAN. We are having issues in this configuration getting the one VLAN to talk to another.
I know if we were in all Cisco mode then we would use ROAS to do this inter-vlan communication. How to make this happen short of changing hardware?
View 7 Replies
View Related
Oct 3, 2012
can I make the stacking of these two switches WS-C3750E-48PD-SF and WS-C3750X-48PF-L. Both have universal IOS.
View 11 Replies
View Related
Dec 6, 2011
I have 3750E swiches with IOS v. 12.2(55)SE3. Couple servers connect to ths switch, after ping of IP this servers I can see mac addresses in mac address table.
For instance:
sw1#show mac address-table vlan 20
Mac Address Table
-------------------------------------------
Vlan Mac Address Type Ports(code)
---- ----------- -------- -----
When ip generate traffic to this server this mac address appear in table again on shot time (less than 10 seconds).
View 4 Replies
View Related
Nov 30, 2011
I had a lot of problems with TCAM table in the past and made changes in SDM ended whit that. But now want to be proactive and anticipate the problems in my TCAM table.
If the my template is "default desktop" they support a number of indirect IPv4 routes of 2k. I wanna know automatically by my management tools if this number reaches 1.9k.
That way I can take corrective actions before the problems starts on my network.
View 5 Replies
View Related
Mar 10, 2008
After I added the 3rd 3750E to my stack on Sunday I can no longer save my configs with 'copy run start' or 'write mem':
#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
nv_done: unable to open "flash:/config.text.new"
nv_done: unable to open "flash:/private-config.text.new"
nv_done: unable to open "flash:/multiple-fs.new"[OK]
[code]....
my flash seems to have plenty of space:
57409536 bytes total (24203776 bytes free)
View 4 Replies
View Related
Apr 22, 2012
We tested a QoS in a Cisco 3750E, IOS: 12.2(58)SE2.Voice traffice in the correct Q without any problem, but all the others traffic the Defualt Q (0), tried to capture the traffic and tcp/udp port are correct.Any thing wrong with my ACL or DSCP - CoS?? ( that ACL works fin on 4500 and 6500) [code]
View 3 Replies
View Related
May 3, 2013
I am not able to find the exact bug for Cisco 3750E stack - Debug Exception (Could be NULL pointer dereference) Exception (0x2000) error. Closest i can find is CSCsa72400 which only affects ver 12.2(20)SE4.All the stacks (3 switches) are running 12.2(50)SE3, It appears that the switch 1 crashed and reloaded. My hunch is its software but i cant find any related bugs. It could be hardware issue as well ?
View 4 Replies
View Related
May 30, 2012
I have a device which will be sending voice and data packets and is able to mark the packets with DSCP values. Voice, 18 and Data 42.If this was a straight through network, I'd be clear on how to handle this, but.....I will be putting this traffic into a VLAN to isolate it from some other traffic on the network. What is the best way to prioritize this traffic inside the VLAN? Will the Cisco switch look at and respect the DSCP values inside the VLAN and prioritize accordingly inside the VLAN? Or, do I need to do some sort of DSCP to 802.1p mapping? Another option I would be fine with would be mapping the DSCP values for voice and data to two different VLANs and then giving the voice VLAN priority over the data VLAN .... I'm using 3750E switches.
View 7 Replies
View Related
Oct 25, 2011
What is meaning backup on HSRP statas?There are 5 vlans.The other four vlans aren't backup status.Only one of five vlans display messeages. When I reload Catalyst3750E-1,debug log. [code]
View 6 Replies
View Related
Apr 22, 2012
Can we stack a 3750G-12S-S switch with a 3750-E-24TD-S switch?
View 4 Replies
View Related
Jul 6, 2012
I am trying to setup intervlan configuration and stuck on a problem. Here are the details:
1. Switches Catalyst 3750-x (as core switch) and Catalyst 2960S (as access switch)
2. Both switches have VLAN 20 and VLAN 1 on their database and both are active. BTW, after I figure out how to properly configure interVLAN routing the native VLAN 1 will not be used anymore. This is just an initial test.
3. VLAN 20 SVI interface (IP 192.168.20.200) on 3750 is up and can be pinged from catalyst 2960.
4. VLAN 1 SVI interface (IP 192.168.170.200) on 3750 is up and also can be pinged from Catalyst 2960.
5. Catalyst 3670 can ping a client computer (IP 192.168.20.10) connected to Catalyst 2960.
6. IP route enabled on 3750
7. Trunking is enabled on etherchannel connecting both 3750 and 2960
8. Client computer in VLAN 20 (connected to 2960) can ping VLAN 20 SVI interface 192.168.20.200 on switch 3560.But, the client computer in VLAN 20 can not reach any computer in VLAN 1 and vice versa. Strangely, the switches which these computers are connected to can ping each other or any connected client copmuters without any problem as described above.
View 8 Replies
View Related
Nov 7, 2012
9x3750E stacked switch (WS-C3750E-48PD-SF0) (15.0(1)SE2
C3750E-UNIVERSALK9-M)
2x10Gbe uplinks from EMC NAS
At a basic level, we have found that the 10Gbe uplinks have slow read performance with or without a port-channel configured (2-3 minutes for a 700MB file to desktop from the NAS) We switched back to testing a 1Gbe and the read speed is normal. Another anomaly is Win7 / 2008 machines read speed is fine from the NAS while the 10Gbe uplinks are in production?!
Write speed is great on 10Gbe. Only read speed is affected!! the switch is not reporting anything abnormal. We looked at SMB/SMB2 as another possible cause...
mls qos is enabled on the switch but not sure if this is affecting performance.
Is the ANY config that I need to carry out on the interfaces to get the read speed working as it should for both Win7 and WinXP. (MTU is 1500 throughout the enterprise, NAS included).
View 1 Replies
View Related
