In my environment we have 3750x switches running ios 15.0 (1) SE2. We have port security mac address sticky configured on all our switch ports. I noticed that we have several interfaces (on different switches) that are up but have not captured the MAC address from the workstation. Here is one example:
interface GigabitEthernet2/0/11
switchport mode access
switchport port-security
[Code].....
I work at a hospital and we have 3750X-48P switches in stacks in various locations throughout the hospital. We have noticed that when an EKG machine is plugged into one of the ports on some of these switches and the EKG machines are set manually to 100/Full, the ports are no longer usable until the switch is restarted. The switch is configured for auto. If the EKG machine is set to auto, it will work and not cause problems. The link on the interface will show up/up and there will be output packets increasing. However, there will be no inputs on the link and the port is unusable. Unfortunately, even when the device is removed, the port becomes unusable for any device. Is there any way to fix this problem without rebooting the switch?
View 5 Replies View RelatedIs there a switch that handle its 24/48 ports at 10 Gbps with copper?. I have checked 3750 X but just handle 2 SFP with 10 Gbps.The requirement is to use this switch as CORE and connect 12 switches (access) using its uplinks at 10 Gbps with copper ( in this case 3750 X can be used).using copper at 10 Gbps the distance is still 100 m?
View 9 Replies View RelatedI have been reading the postings on this site trying to retrieve the MAC address for the client devices (computers, printers) attached to our switches. We have approximately 500 switches and I need to map the mac address to the switch. It appears the OID information is for SNMP v2. We are restricted to using only SNMP v3. I have tried using the Cisco SNMP Object Navigator without any success.
View 2 Replies View RelatedI have hardcoded 1GB ports on 3750X to 1000 and full duplex for all servers connected. THe ports are not coming up with this speed and duplex settings. If I configure them to 100, I am able to see the port is up. Whereas if i connect the same servers to 2950 switches, i can see the ports working fine with 1000 speed ..we have tried with the latest universal IOS as well
View 7 Replies View RelatedWe are having an odd occurance happening to our 3750x stacks. For no apperent reason ports will become unusable. Doing a shut/no shut on the ports has no effect. The weird thing is that the indicator lights will stay solid green even if there is nothing plugged into them. We had this happen a couple months ago and a reboot fixed the issue. But as it has happened again makes me think that is was not a fluke. As of right now it only effects a few ports.
current code we are running is Version 12.2(53r)SE2
we have just purchased a few 3750x's that we intend to add to our 3750g stacks. We've purchased the 10gb uplink modules, C3kx-nm-10gt, but when they are installed they are not appearing in the switches web gui nor can you configure them correctly. If we upgrade a 3750x to 15.0.1 they seem to work fine. All of our current 3750g's are running 12.2(58)SE2 IPBASE so we don't really want to have to upgrade them all to 15.0.1
Are we missing something or do the 10gb modules only work properly with ios 15.0.1?
I need to tear down an existing port-channel on a 3750X running c3750e-universalk9-mz.150-1.SE3.bin. This port channel is currently down down. It has three ports in it that will be added one each to three existing port-channels, I am assuming as long as the "channel-group" command is exactly the same as it is on the three existing port-channels I should be ok just adding the new port. One point to note is that the three existing port-channels all have three ports so this will be adding the fourth port to each port-channel. I know after reading that it is a best practice for load balancing to use either 2, 4, or 8 ports for a port-channel. Also what is the command to see all ports that are in a port channel?
View 1 Replies View RelatedIt seems I have seen this before (and even done it once a few years ago).. but it has been a while. I have a stack with a Cisco 3750 stack that I have to replace a member.The replacement switch is a 3750X.
I think I have to upgrade the IOS of the older switch to be the same as the 3750X.
Current switch: WS-C3750G-48TS 12.2(46)SE
TO BE ADDED WS-c3570X-48 15.0 (1)SE2
It seems to me there was a way to upgrade the older switch IOS from the newer switch or downgrade the newer switch with the older IOS.I dont have the Cisco account to download updated IOSs.
my company pay a switch 3750 X. WS-C3750X-24T-E. It uses IP services basically but I failed to configure InterVLAN routing. why interVLAN routing doesn't work on my switch?
View 10 Replies View Relatedwhile i am configuring a port on switch .The switch reloads.After reload the show version says
System returned to ROM by bus error at PC 0x458F6C, address 0x0
show version from the effected switch is
Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(58)SE2, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
[cODE].....
can I make the stacking of these two switches WS-C3750E-48PD-SF and WS-C3750X-48PF-L. Both have universal IOS.
View 11 Replies View Relatedif we can stack the 3750G switch with a 3750X switch ?
View 7 Replies View Relatedwhen enabling multicasting on layer 3 interfaces the CPU becomes fully utilized , is there any specific configuration should be enabled to reduce this .
Config :
Inetface vlan 100
ip pim sparse-dense
ip igmp version 3
[Code]......
The process "HL3U bkgrd proce" is causing high CPU usage issues in a switch 3750X-24T-L. The IOS is 15.0.2-SE2.
show platform ip unicast failed route and adjacencies displays a lot of entries, I've seen up to 1200.
After restart HL3U bkgrd proce takes around 10 - 20 % CPU, some hours later 99%.
A coupe of times we got logs like this:
%SYS-3-CPUHOG: Task is running for (2136)msecs, more than (2000)msecs (172/73),process = HL3U bkgrd process.
-Traceback= 0x1BE9C3Cz 0x27E103Cz 0x27E0F64z 0x50DCF8z 0x50DE98z 0x503BD0z 0x4F7718z 0x1FF0A18z 0x1F46DECz 0x1F4816Cz 0x1F48698z 0x1F499C8z 0x1FF15D0z 0x2000430z 0x1FF55B4z 0x1FF5FA4z
[Code].....
I have a 3750X 24 port switch (with NM-1G network module) running IOS 15.0(1). Is there any benefit or reason to plug in the included Stack Wise cable and loop it back to itself in a single switch installation?
I don't see any recommendation in the documentation. The data sheet indicates a single switch is a non-blocking device so I'd think there's no bandwidth advantage like there is when connecting an actual multi-switch stack and needing to close the loop for the full 32 Gbps stack bandwidth.
About an hour ago I had the master switch on one of my 3750x (WS-C3750X-48PF-S) stacks crash. The only two items we've found that could have caused this issue are the roughly 1.3 million big buffer misses and several of the following in the syslog
SLT:WARN:No exporter configured for smartlog! I do not have smartlogging turned on, nor is there a netflow exporter configured
sh logging smartlogsmartlog is disabledsmartlog exporter:smartlog pkt length: 64 Total pkts processed: 0Total DHCP Snooping pkts processed: 0Total DAI pkts processed: 0Total IPSG pkts processed: 0Total ACL pkts processed: 0
I did not see any traffic spikes prior to the crash.
This stack has been stable since it's last IOS upgrade from 12.2(58)SE1 to 12.2(58)SE2 back in October 2011 so this has me a little worried.
I've 3750X switch that isn't loading email. then I went to rommon mode and accidently for "format flash". after that I loaded 15.0 SE2 s/w on it using tftp server but it doesn't boot up with that image. flash had only .bin file after I loaded it from tftp server.
since it wasn't booting up, I did format flash again and thought to load image again from tftp server but now, it doesn't load image from tftp server.
I have a 3750X four-switch stack acting as the core of a fairly simple LAN. All I need to achieve (and this seems inordinately hard, but it is entirely likely that I'm just being dense) is to get access to the internet through my core switch, through the firewall and out through my VSAT. I've spoken at some length with the firewall providers (Cyberoam) and they tell me all I need to do when I migrate onto my new system (Cyberoam is currently in place at the entrance to our existing LAN) is change the local IP address of the Firewall, plug in the new switch to the LAN port, and away I go. Tried that, didn't work, so obviously I'm missing something.
View 22 Replies View RelatedI am looking for a way to bind between a switch interface (cat 3750X) and a DHCP server reply.The switch can operate as the DHCP server .a PC connected to interface Gi 1/0/1 will lways get IP address 10.0.0.1 because it is connected to interface Gi 1/0/1, a PC connected to interface Gi 1/0/5 will lways get IP address 10.0.0.5 because it is connected to interface Gi 1/0/5 and so on... (no matter the source MAC address who sends the DHCP request).
View 8 Replies View Relatedi am seeing very high utilization on a random basis on the stack. and the logs indicate me that there is a pattern where there is a stack power cable shows inserted (which was never unplugged) followed by sudden spike in the utilization.
001018: *Mar 6 16:21:22.138: %PLATFORM_STACKPOWER-6-CABLE_EVENT: Switch 4 stack power cable 1 inserted
001019: *Mar 6 18:18:37.982: %SYS-1-CPURISINGTHRESHOLD: Threshold: Total CPU
[Code]......
In change network topology, we are going to assign PC's Gateway as Switch (3750X) IP Address rather than server IP Address. Currently we have configured all Sytems's Gateway is Internet Server IP Address which we are going to replace with Switch IP as Gateway.Issue is while connecting specific application like team viewer in which application tried to send keepalive message to the live server and in case of switch/router IP as gateway. Connection doesn't established. However it is working fine when Internet Server IP treated as gateway.
View 1 Replies View RelatedWe have a 3750X VTP Server and the rest of the switches are clients.
Due to cabling issues, we have a switch (Switch F) that we can't connect directly to the 3750X so we have it connected through another switch. Everything is set to VTP client with the correct domain and password but this not-directly-connected switch isn't receiving any VTP VLANs.
Anything I need to do on Switch D so that Switch F can receive the VTP updates?
I would like to know if it possible to create a policy map in order to redirect the traffic ( 80 , http, 8080) to a proxy.
My current equipment its a 3750X using a IP Service License ,I was reviewing some options but i want to be sure before implement in production.
We have 9 x 3750x switches with 5-nonPOE and 5-POE. There is a limitation with 4 POE per stack with Stack Power.
Can we combine all 9 to one stack since there are only 4 POE?
Or, is the 4-switch limitation applied regardless if they are mixed with POE and non-POE?
I have a LIII Switch Cisco 3750x ,with diffrent Vlans , Some users are in Vlan 102 (10.10.2.0) and Some Users are in Vlan1 (10.10.1.0) , now i want to restrict the Vlan102 users to access Vlan1 , i am pasting my configuration below , how to create a access list .
interface Vlan1
ip address 10.10.1.36 255.255.255.0
ip helper-address 10.10.1.36
[Code].....
I want to limit the bandwidth going to remote site on the switch connecting to our netapp.We have a 4 port channel group setup on our 3750x switch going to our netapp storage. We have a Wan 100mb link to our remote site and we want only 60MBs of that link to be used for Netapp traffic all other local traffic needs to use the full amount of the bandwidth to the netapp.
Is possible to allocate bandwidth in this way and how would I go about this? We dont have access to the routers for the link and they plug directly into a port on our cisco.
Two Cisco 3750X can be stacked together to ensure redundancy.Is the attached topology feasible for access layer redundancy?
View 5 Replies View RelatedI have a 3750x 48port POE switch that I installed a second power supply in. But it doesnt power on. Am I supposed to enable it in the switch somewhere? I've plugged it into a couple different outlets so I know that's not the problem.
View 4 Replies View RelatedI'm trying to get an IP_ADDR set on the management port in SWITCH: mode but for some reason the port seems disabled. PC shows connection unplugged. MGMT_INIT is not a valid command (not listed under '?' ). Bootloader version is 12.2(53R)SE2 FC1.
View 4 Replies View RelatedWhat are the options avilable to add a cat3560 g switch to a stack of 3750x switches.?is there a connector avilable ?or is it possible to trunk via fiber ? cat 3560 has 4 sfps and 224 10/100/1000 ports with poe. cat 3750 stack has a 10 gb up link . What are the possible options?
View 6 Replies View RelatedIn change network topology, we are going to assign PC's Gateway as Switch (3750X) IP Address rather than server IP Address. Currently we have configured all Sytems's Gateway is Internet Server IP Address which we are going to replace with Switch IP as Gateway. [code]
Issue is while connecting specific application like team viewer in which application tried to send keep alive message to the live server and in case of switch/router IP as gateway. Connection doesn't established. However it is working fine when Internet Server IP treated as gateway.
i have a stack of 3750x, with minimal configuration. there are two vlans, and two vlan interfaces with IP addresses. when i ping out from this switch to another host, it picks vlan1's ip address as the source automatically. i tested this by doing two pings with extended options using each vlan's interface as the source, and got different results. how the switch decided to use the first vlan's ip address as a source.
View 11 Replies View Related