Cisco Switching/Routing :: 4506 Switch Is Not Booting With New IOS
Apr 7, 2012
Yesterday I've faced a Problem that is not letting me boot with the new IOS.
Actually I'm planning upgrade IOS which supports SSH. As part of plan I've downloaded the new IOS image and uploaded via TFTP server to the switch.
After uploading to the switch. I've verified image and MD5 hash also. Everthing is fine. Then after I set the boot variable for the newly uploaded Image.
When I'm rebooting the Device it is not taking the new IOS. It's booting with the OLD image. Even It's not showing any error message while rebooting (ACTIVITY FILE ATTACHED FOR YOUR REFERENCE) I can't take risk by deleting the old IOS.
View 1 Replies
ADVERTISEMENT
Aug 13, 2012
i facing problem with my switch cisco 3560G, when it power on only System light is green and noting happen. i check with serial cable ( Console) but noting happen no booting.
View 2 Replies
View Related
Oct 24, 2012
i am facing time daely issues on cisco 2960 s series switch while booting .It is taking time for electing masrer and sleeve for stacking.can i disable the election process for stcking while booting.
View 4 Replies
View Related
Dec 6, 2012
We have sup engine 6L(WS-X45-SUP6L-E) on two 4506 switch. both switches connected in LAN (HSRP primary and Secondary).
We are going to replace it with Sup7LE. What is the best procedure to get this done with minimal outage?Any other important thing to be noted ? Note : We have Lincence for SUP 7LE
View 2 Replies
View Related
Jul 7, 2012
One of my customer had a problem with A/C and the room temperature reached almost 50 C. We came to the site and saved the configuration, took a backup and shutdown the switch.
After the A/C problem is resolved, we tried to power-on the switch .. and we found that it is going to the rommon.
I put "boot" command to boot from the bootdisk, but I am getting the following error:
Code...
I tried to search it, But it is resulting in that most probably it is a hardware failure on the SUP.
View 6 Replies
View Related
Jul 17, 2012
I have 2950 switch booting through MOnitor Mode.Analyzed there is no Cisco IOS image in flash.
View 1 Replies
View Related
May 14, 2013
We want to permit certain mac addresses on the cat 4506 switch wherein only those mac addresses will get access to network.
Configuration Planned: For testing purpose we have created mac access list on cat 4506 and deny laptop mac address in this access list. The mac access group is applied to the port where the laptop is connected to cat 4506.Even after applying the mac access group on the port, the laptop is able to ping the vlan ip of cat 4506 [code]
laptop with ip address 192.168.10.2/24 connected to port 2/1 is able to ping 192.168.10.1 even after applying the mac access-group
Note-we have tested same configuration on cat 3560 and its working fine. We apply the mac access-group command on interface and clear the arp-cache and we are not able to ping vlan interface ip. The moment we remove the mac access-group,ping starts again.
View 4 Replies
View Related
Nov 30, 2011
I have three 4506 switches with vlan 4 set as the management vlan. Switch 1 is connected to switch 2 and switch 3.
I can access switch 1 and 2 using telnet from the management vlan and both switches reply to pings. But from switch 1 or 2 I cannot ping or telnet switch 3. If I plug into switch 3 and I can ping and telnet switch 3 but not switches 1 or 2.
It is as if the management vlan 4 is not being passed to/from switch 1 and 3. The configs for the uplinks from switch 1 to 2 and 3 are the same. And the configs for switches 2 and 3 look the same apart from the port settings.
I have over 40 vlans running all that work fine between all the switches.
View 28 Replies
View Related
Oct 4, 2012
I have a problem with a newly bought ws-x4548-rj45v+ i've plugged in the module but when i do show modules all , it show as unsupport
Power consumed by backplane : 0 Watts
Mod Ports Card Type Model Serial No.---+-----+--------------------------------------+------------------+-----------1 2 Supervisor IV 1000BaseX (GBIC) WS-X4515 JAE1048GAXQ2 48 10/100/1000BaseT (RJ45) WS-X4448-GB-RJ45 JAB064806WN3 48 10/100/1000BaseT (RJ45) WS-X4448-GB-RJ45 JAB063005DB4 0 Unsupported module WS-X4548-RJ45V+ JAE1545056U
M MAC addresses Hw Fw Sw Status--+--------------------------------+---+------------+----------------+---------1 0007.0e64.f880 to 0007.0e64.f881 5.2 12.2(20r)EW1 12.2(46)SG Ok2 000b.5fa4.da20 to 000b.5fa4.da4f 1.0 Ok3 0009.e844.d760 to 0009.e844.d78f 1.0 Ok4 ccef.4815.9bf0 to ccef.4815.9c1f 2.0 Unsupport
View 2 Replies
View Related
May 25, 2013
A 4506 Switch reboot several times a day for no reason, I have been trying to upgrade the software . Normal operation of more than ten days , Still there reason to restart . CPU and memory usage is normal
Switch output information below:
HKZ-SSL-4-NAN-4506#sh ver
Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500e-ENTSERVICES-M), Version 12.2(54)SG1, RELEASE SOFTWARE (fc1) [ code].....
View 3 Replies
View Related
Jan 17, 2013
My management has tasked me to give them a high level overview of the different switching we can choose for our new building.
This is what I know so far.4 Closets, each closet has 450 ports,One MDF room that is will contain one UCS Chassis and a Nimble iSCSI SAN.
I am working on the spreadsheet and it looks like this (Not totally filled):
2960s3560x3750x45064510Approx cost (Each, 48PORT, POE+, 10G uplink, Dual PS, IP BASE)
6K7K8K45K75KMax Capacity192432432192384Backplane speed206464520520ProLeast ExpensiveStackable to 9Stackable to 9ProDual PSDual PSDual PSDual PSDual PSProLayer 3 opt
Layer 3 optDual SupsDual SupsConExpensiveExpensiveConNo Dual PSConLayer 2 OnlyCannot stack more than 4
For the MDF I would like to use 2 Nexus 5548's with FEX's, and the layer 3 daughter board. For the IDF's I was thinking of two 4010's.
View 12 Replies
View Related
Dec 19, 2011
I am implementing a guest wireless network to work alongside my internal network. The guest network will use the existing switching network and will be separated by VLANs. I have the ASA set so that traffic can get to it and out to the Internet. I can set up a workstation on the same VLAN as my guest network and can route inside my network (strictly doing this for testing purposes). Where I am having problems is with the Catalyst 4506 switches and the ip routing. I had two separate "ip route" statements defined on my switches.
ip route 10.200.2.0 255.255.255.0 10.200.2.254
ip route 0.0.0.0 0.0.0.0 10.100.100.254
I have discovered that the traffic is always following the default route despite the fact that my IP address on my test workstation falls in the 10.200.2.x network. I was looking at documentation and found that it is possible to set up policy-based routing on the core switches. Can you have two "ip route" statements defined like this to segreate traffic or do I have to use PBR for routing (or a combination) in this case? If I define PBR then how does that impact my existing routing? I need to make sure that I can still route the existing traffic while I'm configuring this change.
View 9 Replies
View Related
Aug 27, 2012
We have 2 sites, each with 2 x 4506 switches which will be connected togther using an etherchannel. The switches will provide access ports for client devices and will be configured with HSRP to provide gateway redundancy. SW1 will be HSRP active.2 metro ethernet links will be installed in each site which will connect back to our HQ sites. OSPF will be used over the backbone to provide resiliency and to allow shortest path routing to each HQ and to prevent traffic over the HQ to HQ link.
The 4506 will be trunked togther with an SVI for providing OSFP adjacency.For the traffic flow from SW2 to HQ2, traffic will hit SW1 and then route back to SW2 and then to HQ2. Is this the best way to do this? Should a second link be connected between switches just for routing or should something like GLBP be used?
View 6 Replies
View Related
Nov 17, 2012
Yesterday a coleagu accdently removed the CF card from the router now the router does no longer want to boot completely. It extracts the image from the CF card but when it has to initialize the configuration it stucks there for hours. Can it be that the startup config is somehow corrupted?
When i try to tftpdnld is says that the mac address is illegal.
The first line of the cookie looks like 04 ff 08 86 ff ff ff ff ff ff ff ff ff ff ff ff
System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)Technical Support: [URL], Inc.PLD version 0x10GIO ASIC version 0x127c2801 platform with 196608 Kbytes of main
[Code]......
View 7 Replies
View Related
Feb 3, 2012
I have a 6500 that keeps booting into Rommon, even though it has a valid image file on the sup-bootdisk, and the config register is 0x2102. When it reloads I see this on the screen: [code] It seems like the repeating error is "error - on read during ELF program load". I can boot the system off of a CF card, but I'd like to use the sup-bootdisk.
View 11 Replies
View Related
Nov 3, 2012
I tried to upgrade the IOS on my internal AP and now I am in a reboot cycle. I have tried to manually boot the old and new IOS images from the rommon but neither are working. here is the output I am getting:
ap: dir flash:
Directory of flash:/
2 -rwx 6563840 <date> ap801-k9w7-tar.124-21a.JY.tar
4 drwx 256 <date> ap801-k9w7-mx.124-21a.JA1
152 -rwx 548 <date> env_vars
153 -rwx 2775 <date> cpconfig-ap801.cfg
154 -rwx 2775 <date> back_up.txt
155 -rwx 3763 <date> config.txt
[code]....
View 2 Replies
View Related
Aug 11, 2012
I'm having an issue with 2 of my 3560s which are not booting. The last thing I did on both switches before it hangs was:
>write erase
>reload
restarted as normal
[Code]....
I've tried powering-off the switch and pressing the Mode button and power on. I got to swtch: mode switch:reset
It restarted past the POST but just hang halfway at the same bootp-up process as shown on the attached. The SYST LED is Green color when it hangs.
View 9 Replies
View Related
Oct 25, 2012
I bought a CISCO SG200-18 switch. I added the Switch to my LAN and started the Switch (as described in the manual). The Switch starts the booting procedure (green blinking status LED) After a while, the LED starts to blink orange and green, instead of steady green.
In generally the Switch seems to work. I can access my whole network, but not the web interface of the switch itself. I also can't see the switch in the ADSL / DHCP rooter.
I also tried to boot the switch only connected to the PC. But ping on 192.198.1.254 is not working. The switch is in the same subnet like my other LAN components.
Subnetzmaske . . . . . . . . . . : 255.255.255.0
Standardgateway . . . . . . . . . : 192.168.1.1
I exchanged the switch. But the new switch shows the same behavior.
View 3 Replies
View Related
Aug 22, 2012
I have a new cisco 1941 router that I am setting up with pxe-booting. I have never setup pxebooting before and i have this setup so far ip dhcp pool Admin
-option 66 ip 192.168.1.4
-option 67 ascii pxelinux.0
and i can pull an ip but it keeps getting hung up when it comes to the TFTP part.
View 4 Replies
View Related
Jul 3, 2012
An ASA 5505. Device boots to rommon #0> and stays there. The complete boot record follows:
CISCO SYSTEMS
Embedded BIOS Version 1.0(12)13 08/28/08 15:50:37.45
Low Memory: 632 KB
High Memory: 507 MB
[Code]....
View 15 Replies
View Related
Aug 31, 2012
CiscoSwitch1(4506) has 3 VLANs(12,13,14) and Switch2(4948) has 3 different VLANs(22,23,24) and IP routing has been enabled in both switches with SVI interfaces for each vlan. intervlan routing is works fine.Now there is a requirement to connect these switches together. Vlan 12 on the Cisco switch 4506 has to be made available from vlan 22 from Switch2(4948). basically Vlan 12 is having a multicast source (225.0.0.0 & 226.0.0.0) which should be accessabile from vlan 22 of cisco switch 4948.I got 2 ideas
1) Create a trunk between these switches and configure L2 vlan(12) in cisco 4948...i know theoritically it should work but what my concern is Ip routing enabled in both switches will it create any issues? is it a gud solution to this requirement?
2) Create a separate IP network on the ports connecting to both switches and set up routes to the networks.ex- console(config)#ip route 192.168.10.10 255.255.255.0 192.168.20.1.
View 8 Replies
View Related
Mar 8, 2013
I am configuring multicast in a environment where I have a 4506 at each site (4 total) and a 6506 as the core. Each 4506 is connected via layer 3 to the 6506. I have a mix of 3560s, 3548s, and 2960s connected to the 4506s and the 6506 via layer 2 trunk
I have multiple multicast sources and hosts communicating at a time (multiple cameras sending video / multiple computers receiving video). So this is not a scenario where there is 1 sender and many receivers. This would be many senders (~50) and some receivers (~10)
Sample Diagram:
->3560
|
6506 --> 4506 --> 3548
| |
| --> 2960
|
4506 --> 2960
|
-->3548
I configured ip multicast-routing on each of the 4506s and on the 6506. IGMP snooping is on by default on the 3560 and 2960 switches. CGMP is on by default on the 3548 switches.
I set up PIM sparse-dense mode and IGMP version 3 on each of the layer 3 interfaces for the 4506s and 6506 where they connect and on each VLAN that is sending or receiving multicast. Multicast is working throughout the network, however I am looking to verify the configuration as I scale this out to more clients on the network.
#1 - Is it correct to us sparse-dense mode in this configuration?
#2 - Do I need to configure a rendezvous points using AUTO-RP? (ip pim send-rp-announce INTERFACE scope TTL). Not sure here if I need to designate this and what to choose. Right now I do not have this and it is working, but documentation seems to infer that I need to designate this.
#3 - Is there any other configuration settings I should be considering? I hard to find real world configurations of multicast as examples or people that know multicast routing well.
View 3 Replies
View Related
Mar 3, 2013
I have a brand new 3650x switch that I was configuring via console and left it on overnight; this was friday night ( I forgot to keep the air conditioner on). When I returned Sunday afternoon and checked the switch I realized that the SYS and STAT lights on the front were not on, however the Leds on the PS module were still on. I powered it down and turn it on again but still there are no lights on the front. The PS OK and AC OK leds on the PS module are on but I noticed the leds on the two fan modules are not green or even amber; they are off.When I first turned on the switch I remembered distinctly that there were loud noice and if all fans were in overdrive mode for a few seconds then the went to normal. I'm not gettgin this loud noise phenomenom.
View 9 Replies
View Related
Jul 23, 2012
One of the 6500 was going in bootrom mode, so I have formated the flash disk using the other Cisco 6500 switch and copied IOS file to the boot disk. But the 6500 booting failed.
View 6 Replies
View Related
Jan 4, 2013
I am currently running a 4506 with a sup V engine. I have purchased a sup 7 engine. Is there a guide on how to perform this task. I am sure I need to do an IOS update as well.
View 2 Replies
View Related
Jun 11, 2012
We are attempting to PXE boot from clients obtaining their DHCP lease information from DHCP pools configured on our 4506. The PXE server, and the client are configured in separate VLANs. We have configured option 66 to point to the PXE server IP address, and the bootfile option to point to the PXE boot configuration filename. On the client side SVI, we also have configured the ip helper-address command to point to the PXE server (which also acts as another DHCP server for redundancy).
The PXE boot continuously fails stating it is unable to find the configuration file. If we remove the DHCP pool from the 4506, and allow the client to receive their DHCP lease info from the secondary server (Windows 2k8 - same server as PXE server), they PXE boot with no issues.
We have no problem obtaining DHCP info, just completion of the PXE process.
View 6 Replies
View Related
Mar 19, 2013
Does SUP 7E is comatible with IOS? It came with IOS-XE preloaded and there are no IOS software listed under downloads.
View 3 Replies
View Related
May 8, 2013
I have 4506 with below sup, my requirement is to enable netfolw , but as i came to know that it is not supported in this sup, is there any additional option which can be explored to get the netflow working without replacing sup.
Card Type Model
-------------------------------------------------------------+-----------------------
Sup 6-E 10GE (X2), 1000BaseX (SFP) WS-X45-SUP6-E
View 4 Replies
View Related
Feb 29, 2012
today I received a Cisco 1841 Router with a problem i have never seen before. Maybe this my 1st really,really broken Cisco Router. When I power the Router on, the fan and all lights turn on (green) and that's it. Nothing changes, also after minutes of wating. On console i don't get any messages and I already tried every BAUD rate possible. Switched the router off/on again and again. And no, it's obviously not a console problem of my computer, because i tried with different routers.
View 3 Replies
View Related
Dec 5, 2011
I have a 4507R with a WS-X4515 supervisor V. It was booting into rommon mode, so I attempted to boot to an IOS image from TFTP. The boot process hangs at at the end of the below output and the then the status light blinks orange. I left it sit like this overnight, and it remained the same.
rommon 23 >boot tftp://x.x.x.x/cat4500-entservicesk9-mz.122-53.SG2.bin
Tftp Session details are ....
Filename : /cat4500-entservicesk9-mz.122-53.SG2.bin
[Code]......
View 9 Replies
View Related
Dec 12, 2012
I have a Catalyst 4506e that works fine but if reload, it boots in rommon mode. I can start it with a boot command, but by default, i must type a command. My config-register is 0x2102.
View 5 Replies
View Related
Feb 28, 2012
I have a cisco 7606-S with dual RSP720-3CXL. Devices reloaded and now none of the RSPs are booting.When I have tried to take the console using only one RSP, card going to rommon mode after that it hangs. I guess its firmware is corrupted.
View 4 Replies
View Related
Oct 24, 2010
We have just purchased and installed a 4506-E chassis. It contains a supervisor, two POE blades and 3 non-poe blades. Version is 12.2(53)SG1. Anyhoo, one of the ports isn't providing power to an IP phone. We can plug the phone into any of the other POE ports and it works fine. Is there a way to test an idividual port for POE problems? What could the problem be? The port works for normal data but will not provide power.
View 12 Replies
View Related
