I have two switches that always are with yours CPU in 39 or 40 %. the switches are:
IOS (tm) C3500XL Software (C3500XL-C3H2S-M), Version 12.0(5)WC3b, RELEASE SOFTWARE (fc1)
I think it's very strange the CPU always in 39 or 40 %. neither all ports of the switches are busy there are 6 ports free in each switch. 40 % I think it is a high value for CPU maybe because my IOS version 12.0 ?
How do I find interface to which an ifentry is associated with in Cisco IOS Catalyst switches ?
#sh snmp mib ifmib ifindex does not seem to work
As per information from the Cisco document , the command was introduced in IOS version 12.2(T) and higher [URL] The IOS version the switch I am working on is 12.0(5) The relavant info from #sh ver is as given
Cisco Internetwork Operating System Software
IOS (tm) C3500XL Software (C3500XL-C3H2S-M), Version 12.0(5)WC17, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2007 by cisco Systems, Inc.
Compiled Tue 13-Feb-07 15:04 by antonino
Is there any way I can find that in an IOS prior to 12.2(T) ?
im trying to find out what is the latest ios version for 3500xl switch for upgrade it .
View 4 Replies View RelatedI am having a Cisco 4507 switch. The CPU on the switch is running between 50% to 60% constantly. To troubleshoot I collected some logs using debugs & show commands.
debug platform packet all receive buffer
show platform cpu packet buffered
debug platform packet all count
show platform cpu packet statistics
show processes cpu sorted | exc 0.00
show platform health
show platform cpu packet statistics
show platform health output shows the below process crossing the target value.
%CPU %CPU RunTimeMax Priority Average %CPU Total
Target Actual Target Actual Fg Bg 5Sec Min Hour CPU
Stub-JobEventSchedul 10.00 13.41 10 47 100 500 13 13 10 5462:52
K2PortMan Review 3.00 5.35 15 11 100 500 4 4 3 1799:47
What I need to know is, though these process are running in Low Priority, will there be any issue if the CPU goes high due to these process.
We are running Cisco 6509-e and we are running load test and when traffic reach 80 mbps switch start reponding very slow. I checked CPU usage and it was using 100% and connection to the switch from outside to inside are 80K. once connection dropp Cisco release CUP and it start responding normal. [code]
View 4 Replies View RelatedI have one Catalyst 4503 with Supervisor 7L-E 10 with IOS - XE 03.02.00.XO. . One of its gigabit interfaces is connected to a Internet link of 1 Mega. In terms of QoS i would like to limit the total bandwidht of this gigabit interface to just one 1 Mega and simultaneous i want share bandwidth between traffic classes with bandwith percent up to 1 Mega and not 1Giga.
View 1 Replies View RelatedI have just finished installing LMS 4.2 on a new VM (Windows 2008 R2 Standard Edition SP1). I have already reloaded the server, all LMS services have correctly started. However, the process CS_sm_server.exe still using 100% CPU.Windows 2008 R2 Standard Edition SP1
View 6 Replies View RelatedWe have two offices connected using Site-to-Site VPN (IPSEC) as shown:(IP ficticius)Office 1 - We had to use 2 routers since we have a range of valid IPs: From a host in office 2 we normally ping 192.168.102.1 (gateway at office 1),But when pinging a host inside office 1 (eg: 192.168.102.8) 50% of packets have been lost.Could it be a hardware problem?
View 1 Replies View RelatedI am working at a client site that is an MPLS customer. The customer has an MPLS circuit that runs between their Main HQ and their Disaster Recovery site. I have been asked to analyze and report as well on the way the Qos Policy is written, and to provide any recommendations on how they can improve performance.There is a statement within the Qos Policy as it exists at each end on the 3825 routers. The statement is called "shape average percent". Here is the policy from one side:
policy-map QoS
class COS2_traffic
set dscp af31
shape average percent 12
bandwidth percent 13
[code]....
What does this statement mean and how is it different than the the "bandwidth percent" statement?
Im running ASA 8.0(3) on Active/StandBy failover pair.Last night I realized the CPU usage of my production ASA was 99%,,, on the ASDM Firewall Dashboard I can see counters like this:
Dropped Packet Rate (ACL Dropped) = 6000+ (more than 6 thousand)
Scanning Attacks = 18600+ (more than Eighteen thousand)
I went on the ASDM and checked the RealTime Log viewer and I have about 30 entries per second of these:
4Oct 19 201111:35:12401004Shunned packet: 10.64.10.1 ==> 10.64.0.1 on interface NewLAN
[code]...
after IOS upgrade to 15.x on Cisco2811 MEM util raised from 20% to 43%. Is it critical?Which level of MEM utilization is critical?
View 6 Replies View RelatedI have an ASA 5520 with a CSC-SSM modul,the problem is when i am logging in to my ASDM, on the content security monitoring, it's showing the CPU and memory are at 100%(CSC) but when i directly connect csc-ssm MODULE it comes down,so is it problem with ASDM , java OR csc.
View 5 Replies View RelatedWhenever i try to download an exe file from the internet, its just get stuck at 99%. It doesn't happen with .rar or any other file. Not to mention, I was able to download net fremwork 4.0 exe installer though. I tried these things: Used different browsers. Used different download managers. Disabled firewall and AV.
View 1 Replies View RelatedI have ATT DSL and pretty much every night, I lose a large portion of the Internet. I cannot ping these sites, while the rest of the net works fine. The other night, I could not ping major domains like ATT, CNN, MSNBC, BBC (a chronic missing domain). On the other hand, I could get Yahoo fine and go to a streaming audio site and run music perfectly...but about 90% of the Internet was unreachable. Could not load their sites nor ping them in command line. The other 10% worked flawlessly.
View 12 Replies View RelatedI installed a CSC-SSM-20 module on ASA 5510. After policy services have been enabled, services works well for a few minutes, after that the cpu usage's module rise to 100% and all http traffic is wholy blocked, till the cpu usage go down.This happens very frequently and traffic stay blocked for such a long time that it makes the csc-ssm module unusable. It's disabled right now. ASA version is 8.2(1)and CSC-Module version is 6.6.1172.0.
View 1 Replies View Relatedwhenever I setup URL filtering in 1841 router with policy-map type http and zone-pair command, I experience 100% CPU spike. is there any workaround?
View 1 Replies View RelatedWe have a client that has a large number of AIR-AP1252AG-N-K9 installed in the network with power injectors. We have seen a about 48% failure rate of AP's failing with all 3 red lights on the unit. Once I get the AP in the lab I'm unable to get any response from the console, therefore unable to troubleshoot.
View 3 Replies View RelatedTrying to update my firmware 1.00.01 B15 to 1.00.01 B17. I downloaded the firmware to my desktop (using mac os X 10.5.5) and connected my computer directly to port 1 on the back of the router. I used the Firmware upgrade tool under the Administration tab to upload the new firmware file. The update progress starts but fails at 98%
View 4 Replies View RelatedI am buying a Nexus 5K (N5K-C5548UP-FA) with the layer 3 card (N55-D160L3 - Nexus 5548 Layer 3 - Daughter Card).The switching capacity of it is 960 Gbps but I know I should expect less doing the Layer 3 function (it will only be used with static routing).What switching/routing capacity should I expect? How can I estimate it? What else should I consider?
View 1 Replies View Relatedwe've had an issue with our network, we have 2 6509 connected with redundancy, which are connected with 2 x 4900 Switches, from which are connected to a ESX Chassis for visualization, the thing is that the ESX stopped working, and the 4900 switches, and the main core were suffering from overload, they hang on it very well, in order to stop the overload, one of the links to the ESX Chassis were disconnected from one of the 4900 switches. The CPU usage from the 4900 and the core(6509) went down below 40%, and then they started to migrate the virtual servers from the chassis to another 2 chassis that were added right after. They were actually working well, but suddenly the 6509 changed to the other supervisor after everything was OK. We were wondering what could have been the cause of this, maybe the virtual servers migrations, maybe the overload from the ESX ? We also had a few question, is there any need to reload the cores every few months as a planned task ? Because the cores have been up for more than 1 year. And also is there any kind of of tool to monitor the CPU status, or the status overall from the cores or the switches ?
View 3 Replies View RelatedI am facing an isssues with 7609 for LAN switching , based on LAN (VRRP/HSRP) feature.Actually we are having ES+ cards (on 7609) and we are using multiple groups(say 350 vrrp groups) running on the router . the routers are connected as router 1>>> mux(which is working as switches)>>> router2
my questing are
1. does their will be "multicast packets" (for VRRP/HSRP group) "from backup router to Master router", when in stable state( ie when Master and backup are already chosen) , or the packet from backup to master should be unicast.I know for sure, the packet from master to back is multicast packets denstination to Multicast IP packet and To MAC address.I am not sure but I think from backup to master it should be multicast
2. what is frequency of these packets( from backup to master)
3. As i have multiper group on a single interface ( we are using q-in-q), when the connectivity from router's is broken, then does all the groups will muticast their active roll in the lan sengment "at once" or it will be in a groups say 100 groups at once, and after few ms few 100's and sone ( as is on OSPF or RIP)
we are in between troubleshooting I hope we get the ans( Actul problem we are seeing in the router's that we have 2 ports on active routers and 2 ports on standby router , but we are not seeing muticast on 1 port on standby router where as all other 3 ports are seeing multicast packets) [code]
I would like to know if Catalyst WS-C3750G-48TS-E recognizes and understand Cisco VSS ( Virtual Switching System) . Is there a List available which tells us which Old Catalyst Switches or current switches understand Cisco VSS?
View 3 Replies View RelatedWe are in the process of switching our infrastructure of our routing/firewalls/vpns over to cisco. We are switching our first location and one of the issues I'm struggling with is windows authentication pass-through for internally hosted web pages. Meaning, user inside our network has the 2921 as their default gateway, they try to access a web page that is hosted on the internal network but is secured with windows authentication. In the past, because they are logged into the domain internally, the website authenticates and loads. After switching to the Cisco, it asks for a password even though they are logged in.
Because its the web server that actually authenticates I'm not sure why the router isn't allowing that to happen, but I can't think of anything else that could be causing this behavior.
Does the nexus 7010 support virtual switching yet? All of the posts I have found from about a year ago say that it is going to be supported, but there were no dates listed. I heard the same thing from Cisco a while back, but haven't followed up with it.If it is supported finally are there any configuration guides available for it?
View 7 Replies View RelatedI have the following devices :
-1 VM Host
-2 Layer 3 switches
I would like to provide full redundancy for all vlans being used by VM Guests on the VM Host as well as the management vlan being used by the VM Host.I have created two LACP etherchannel connections on the VM Host. Each etherchannel from the host consists of 4 ports spanning a single NIC. One etherchannel connection goes to a trunked etherchannel connection on switch 1, and the other etherchannel connection goes to a trunked etherchannel connection on switch 2.Switch 1 and switch 2 have an etherchannel connection between them that carries all of the vlans in the topology.Vlan 2 is the managment vlan. Vlans 3, 4, and 5 are vlans that VM guest systems will be using for normal data traffic.
I intend to use switch 1 as the VRRP active router and spanning-tree root bridge for vlans 2 and 3.I intend to use switch 2 as the VRRP active router and spanning-tree root bridge for vlans 4 and 5.The spanning-tree configuration is using multiple spanning-tree with two instances. Instance 1 has vlans 2 and 3 associated and Instance 2 has vlans 4 and 5 associated. I would like to have this topology be fault tolerant to the point where if one of the etherchannel links between the host and one of the switches goes down, (for example, if switch 1 was powered off) traffic will be automatically redirected through the other functional link. I believe that my VRRP configuration would allow for a fairly quick failover of layer 3 services, but I am not certain that my design will be functional at a layer 2 level.
What I am uncertain about is how spanning-tree will converge. I am assuming that the virtual switch on the VM host will not be forwarding any BPDUs being sent by either switch. Would either of the links connecting to the host be considered a redundant link by either switch?Would the link between switch 2 and the host be inactive for all vlans in MST instance 1 during normal operation?Conversely, would the link between switch 1 and the host be inactive for all vlans in MST instance 2 during normal operation? Would all links remain active for ALL vlans? Would this mean that some traffic may travel through switch 2 to reach switch 1 instead of going directly to switch 1?
As per my understanding 6509 all slots are dual channel, so 9 slot * 40 per slot (20 g in and 20 g out) = 360 GB How cisco claim the 720 ?? What about the 6513 chassic switch fabric connection?
View 5 Replies View RelatedIt is said that the switching fabric of WS-C3750X-24T-E is 160Gbps.Could any body tell me what is switching fabric, any relevance or difference from forwarding rate?,Is there any document to know how will the switch reach the 160Gbps full switching fabric performance?
View 5 Replies View RelatedI got Two Distribution Switches of Cisco 3750G. Each Distribution have two 3750G switches stacked. I also have one Cisco 3750V2 Access Switch connected to both Distribution. When I am checking for redundancy, I can only get redundancy test pass for one link not atall for other. If I have a link up with Distribution 1 only then its fine; but disappointment with Distribution 2 link. I can see that the switch priorities of Dist 2 is not correct ie. Master's priority is 10 and Member's is 15.
My question is that due to misconfigured priorities on Distribution 2 stack switches I am failing with redundancy if ONLY Dist 2 is up and Dist 1 is down.
I am seeing a strange situation on my 6500 switch?By having snmp walk on '1.3.6.1.4.1.9.9.109.1.1.1.1.3' (== cpmCPUTotal5sec), I came to know that there are two processor and the cpu util for switching processor is gone to 88 % and some time creeps to 99 %.
snmpwalk -v2c -c "removes" sw6500 '1.3.6.1.4.1.9.9.109.1.1.1.1.3'
SNMPv2-SMI::enterprises.9.9.109.1.1.1.1.3.1 = Gauge32: 12 (--- this is for CPU of Router Processor )
SNMPv2-SMI::enterprises.9.9.109.1.1.1.1.3.3 = Gauge32: 99 (--- this is for CPU of Switching Processor )
but when I do sh process cpu on the console, all looks normal as it shows cpu utilization of RP. why the value is so high on the switching processor ?
It is understood that sub-50 ms ERPS convergence can be achieved with certain HW/SW combinations.
1) What are the platforms supported (and with what FW/SW) has this been tested ?any results that can be shared?
2) Link failure detection in GigE on Copper is slower compared to GigE over "pure" Fibre; so no sub-50ms would be possible with Copper ring ports.is sub-50ms convergence achievable with "combo SFP ports" ?
Lucien is a customer support engineer at the Cisco Technical Assistance Center. He currently works in the data center switching team supporting customers on the Cisco Nexus 5000 and 2000. He was previously a technical leader within the network management team. Lucien holds a bachelor's degree in general engineering and a master's degree in computer science from Ecole des Mines d'Ales. He also holds the following certifications: CCIE #19945 in Routing and Switching, CCDP, DCNIS, and VCP #66183
View 1 Replies View RelatedMy management has tasked me to give them a high level overview of the different switching we can choose for our new building.
This is what I know so far.4 Closets, each closet has 450 ports,One MDF room that is will contain one UCS Chassis and a Nimble iSCSI SAN.
I am working on the spreadsheet and it looks like this (Not totally filled):
2960s3560x3750x45064510Approx cost (Each, 48PORT, POE+, 10G uplink, Dual PS, IP BASE)
6K7K8K45K75KMax Capacity192432432192384Backplane speed206464520520ProLeast ExpensiveStackable to 9Stackable to 9ProDual PSDual PSDual PSDual PSDual PSProLayer 3 opt
Layer 3 optDual SupsDual SupsConExpensiveExpensiveConNo Dual PSConLayer 2 OnlyCannot stack more than 4
For the MDF I would like to use 2 Nexus 5548's with FEX's, and the layer 3 daughter board. For the IDF's I was thinking of two 4010's.
I configure HSRP on Router 2951 as a primary router, and Router 2811 as backup router. But when I am switching off my Primary router the backup router is taking 2 mins to take over form primary router.
[code]....