Cisco Switching/Routing :: Clarification On ARP 1700 Received More Than 30 Entries
Apr 15, 2013
As a matter of fact i am new to this field .I have cisco 1700 series router which has ea0 and FE 0 port
E0 connected to LAN and FA0 for ISP ,both are configured wit publisc ip.and ststic route to ISP. (E0 connected to switch and fa0 connected to ISP MUX)
When i issued sho arp command i have received more than 30 entries of MAC and IP address . I am wondering how i received this much mac in arp table.
View 5 Replies
ADVERTISEMENT
Nov 30, 2011
I just replaced my older D-Link with a DIR-601. I decided to try the email feature, so I set the option to "On Log Full". Within an hour I had 5 emails. I noticed that they were mostly entries reading "DIR-601 local0.debug udhcpd[18594]: UDHCPD Received a SIGUSR1". The "Debug Information" option isn't checked.
View 1 Replies
View Related
Jan 25, 2012
What’s the maximum bandwidth (ADSL/internet) supported by ISR 800 series routers … particularly 891 security model.
View 23 Replies
View Related
May 19, 2013
I currently have a 3560G switch running c3560-ipservicesk9-mz.122-58.SE2 I have a spare 3560 V2 switch I want to configure and have ready in case of a failure. This spare switch is running c3560-ipbasek9-mz.122-55.SE5 My plan was to pull the IOS image from the current switch and upload it to the spare that way I have an "idnetical" switch. From what I have read, there are some feature differences between "ipbase" and "ipservices". However, when I run the show license command on the production switch, I get an unrecongnized command error. So that throws into my confusion as if its running an ipservices image, shouldn't it have a license file?
View 4 Replies
View Related
Jul 12, 2010
We want to configure the "mac-address-table synchronize" command on our 6500 series switches to ensure that the CAM tables on our DFCs are in synch with the PFC on the supervisor modules. url...it is recommended that we disable the routed MAC purging with the mac-address-table aging-time 0 routed-mac global configuration command. What is a routed mac entry? Are there any issues with running that mac aging-time command?
We also plan to run this command "mac-address-table aging-time 14400" to keep our ARP and CAM tables on the same aging time to reduce unicast flooding on our network. Can we run this command with the "routed-mac" command above?
View 2 Replies
View Related
Jan 23, 2012
We currently have a main network running through a static broadband connecting using a Cisco 1700 ADSL router, everything is working fine locally.
We are looking to rent some space in an office nearby so im going to order another business adsl connection with static IP for this site and i currently have a spare 1800 router.My question is can the cisco routers connect up like a VPN connection so both sites work together and will the connection remain online constantly so from the remote office we can access all our servers from the main network?
Also how does the IP addressing work on 2 sites. The main network uses 10.120.21.x and DHCP is assigned from a cisco router. Does the remote network assign from the same DHCP server or would the remote sites cisco router need to be setup to give out DHCP to local machines. If so what would be the best IP setup to use.
View 9 Replies
View Related
Apr 4, 2013
I have the ME3400 deployed in an the following design. 8 100Meg ports connects to Cisco 2955s, and the 1Gig port uplinks to a Cisco 3560. My CDP neighbour table only shows an entries for the uplink Gig port. If I look at the CDP stats in the show cdp Interfaces Fastethernet 0/1,, I see CDP packets being sent every 60, but nothing returning.
View 4 Replies
View Related
Jul 15, 2012
How many VMs can a pair of 5548s support? Remember, for each VM, I will have an ARP entry in the 5500 ARP Table (assume 5500 is the L3 default gateway).
View 3 Replies
View Related
Sep 11, 2007
On occasion I will have to clear the ARP cache on a 6500 when a customer swapeeds out a firewall or firewall NIC. The ARP cache will show the MAC of the previous device and will not update until either the ARP table refreshes dynamically (currenty at default time) or it is cleared manually.
Sometimes I need to clear it manually and sometimes is is refreshed dynamically when the new device comes up. Inconsistant issue....
Under what circimstances will an ARP entry NOT be refreshed when a firewall or firewall NIC is swapped out.
View 2 Replies
View Related
Jan 13, 2008
Just a very quick one. Is there any physical limitation to how many ARP entries a 6509 and sup720 can have?
View 4 Replies
View Related
Feb 26, 2012
I was looking for a way to connect an AUX port from a 1700 router to a 6500 switch module console port, to see the output of the Switch's on the 1700 router, in case there is a network downtime, I could see what's going on in the switch, what cable should I use ? Also, is there is any kind of documentation for this type of config what have I seen is very few info.
View 2 Replies
View Related
Dec 1, 2011
I have a question concerning about how many ospf and bgp route entries does 3945E isr g2 router support?
View 6 Replies
View Related
May 21, 2012
One of our client wants to know "How many route entries a 2821 router or 881 router can support" Such as the 3750 can support 11k routes in ‘desktop routing’ mode. But I want to know the limitations on routers.
View 1 Replies
View Related
Jan 11, 2012
I obtain this message on Nexus 7000:2011 Dec 22 03:37:53 NNN %STP-2-RECV_BAD_TLV: Received SSTP BPDU with bad TLV on port-channel1 VLAN0020 and following with err-disabled port ?[URL]
View 3 Replies
View Related
Mar 27, 2012
We have Cisco IP phones behind a 2600 series router:Most of the time when the PBX receives a packet from the phone, the source IP of the packet is set to the public IP of the router (1.2.3.4) as expected. However, once in a while, we get packets (at the PBX) with the source IP set to the private IP of the phone (10.0.0.12).The router is configured by our provider, and they can't give us any explanation for this behaviour. Is it safe to assume that PAT is not configured properly at the router?
View 2 Replies
View Related
Mar 25, 2013
I have a Catalyst switch that is redistributing some static routes into OSPF. These are received on a Nexus 7K and appear in the database however the 7K does not add them to its routing table, one of the routes is ignored and not added. I haven't got a clue why this is happening.
The routes on the Catalyst are as follows with ID of 172.30.255.22:
ip route 172.24.59.0 255.255.255.0 10.56.7.46
ip route 192.168.168.0 255.255.255.0 10.56.7.62
on the 7K the database shows:
172.24.59.0 172.30.255.22 1374 0x80001a44 0x1a48 0
192.168.168.0 172.30.255.22 1374 0x80001a45 0x6c5b 0
The routing table shows:
sh ip ro 172.24.59.0/24IP Route Table for VRF "default"'*' denotes best ucast next-hop'**' denotes best mcast next-hop'[x/y]' denotes [preference/metric]
172.24.59.0/24, ubest/mbest: 1/0 *via 172.30.253.10, Po7, [110/20], 20w4d, ospf-NCC, type-2
sh ip ro 192.168.168.0/24IP Route Table for VRF "default"'*' denotes best ucast next-hop'**' denotes best mcast next-hop'[x/y]' denotes [preference/metric] Route not found
View 5 Replies
View Related
Dec 6, 2012
I am receiving this error after connecting a copper adapter on a GBIC blade in a 6509. Here are the results from the show Interface. I am waiting to confirm the device on the other side settings but as far as I see I get UP and Up for protocol and line respectively.
GigabitEthernet2/11 is up, line protocol is up (connected)
Hardware is C6k 1000Mb 802.3, address is 0009.11e4.f3ce (bia 0009.11e4.f3ce)
Description: RCPBSDEV
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
[code]....
View 3 Replies
View Related
Nov 16, 2011
Cisco LMS 4.0: Is able to forward SNMP traps (ver. 2c) received from device registered with it to a configurable IP address? • Traps contain the original Device Agent IP to identify the source (Not the IP of LMS)?• Is possible to configure one logical IP address or Domain Name for redundant LMS:Cisco Security Manager 4.1:Is able to forward SNMP traps (ver. 2c) received from device registered with it to a configurable IP address?• Traps contain the original Device Agent IP to identify the source (Not the IP of Security Manager)? • Is possible to configure one logical IP address or Domain Name for redundant Security Manager?
View 0 Replies
View Related
Sep 3, 2012
Most of the 4500 Switches in our network are giving the similar error for so many ports
%C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 1 times)Packet received with invalid source MAC address (00:00:00:00:00:00) on p t Gi2/6 in vlan 100
Its impossible to do a wireshark packet tracing for all the ports.
View 2 Replies
View Related
Feb 14, 2012
Issue I am having with a Cisco 4507? Below is the error i am receiving.
Feb 14 10:06:09 EST: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 508 times)Packet received with invalid source MAC address (00:00:00:00:00:00) on port Po10 in vlan 112
Feb 14 18:44:06 EST: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 119 times)Packet received with invalid source MAC address (00:00:00:00:00:00) on port Po10 in vlan 112
Feb 15 00:51:06 EST: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 366 times)Packet received with invalid source MAC address (00:00:00:00:00:00) on port Po10 in vlan 112
[Code]...
View 9 Replies
View Related
Jul 26, 2011
I have an old modem Cisco 1700 with ADSL as backup connection. I have configured PPPoA, the sync is OK and connection is UP. I get Wan IP et Gateway, (routes automatically added). I have added NAT and routes but impossible to go out.I try to ping an external IP but no response.
version 12.2
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname cisco-modem(code)
View 7 Replies
View Related
Nov 27, 2012
Is there a Table which the list the route table entries on Cisco ISR Router especially ISR 1921 Router.
View 3 Replies
View Related
Sep 13, 2012
I have an Acer Aspire one that connected perfectly to the internet until I did a reformat. Now it only works if through a wired connection or if the internet does not have a password protection. I have tried on 2 different locations with secure wireless and both have the same result. Packets are sent but not received. All other devices in either location are able to connect to internet through wired or wireless connections.IP address is at 192.xxx and DHCP is enabled, TCP/IP is set to obtain automatically and I deleted and downloaded the newest drivers from the Acer website twice. I also did a winsock reset and tried to clear the arp cache? One of the issues I am getting when I run the diagnostic is "warn default gateway address could not be resolved via arp". I'm not sure how to resolve that.
View 1 Replies
View Related
Sep 19, 2012
I have got two L3 switches, Cat3550 and Cat3560X. Cat3550 is present at head office and Cat3560X at the branch office. Both connected by 10MB LES link and have VLAN74.
[code]...
View 2 Replies
View Related
Jan 15, 2011
I have a really weird issue with my cisco catalyst 3560G.
-device: cisco catalyst 3560g
-ios: 12.2-53(SE) IP SERVICES
scenario: configured IPv6 iBGP link between this switch and a router. the router is announcing 1 (test) route. the switch sees the route properly, but doesn't add it to routing table (the route never gets to be "best path", although it should be).
View 15 Replies
View Related
Mar 6, 2013
I have 3 WLC's currently running version 7.0.116 and a WCS on version 7.0.220. I am looking at upgrading the versions and am uncertain as to the compatibility.
1. Upgrade the WCS to 7.0.240, and upgrade the WLC's to 7.3. Resulting in my WCS just not able to manage the "new features" in the latest WLC code?
2. Upgrade the WLC's to 7.3 resulting in WCS completely unable to manage the WLC's? I am aware there is WLC 7.4 code however I've read there is an issue with 1142 AP's rebooting.
View 2 Replies
View Related
Apr 10, 2013
Recently I came across a wireless design whcih I ws not able to understand.The design is:
1. Two wireless LAN Controllers 5508, each with 25 AP license. AP load (5APs per Contorller) shared between the WLCs and congured with Backup Controller option.
2. The design has a Data Center Switch 3560x series, on which the two WLCs, Cisco Prime Infrastructure and Cisco MSE were connected. I've attached the design here.
3. The Data Center Switch is configured with DHCP pool for the wireless clients. The IP Address of the Data Center Switch is : 10.xx.xx.2 and Default Gateway is: 10.xx.xx.1
4. On the WLC, the Management Interface is configured with the IP Address: 10.xx.xx.21 for Controller 1 adnd 10.xx.xx.22 for Controller 2. But, their DHCP Server is configured with IP Address: 10.xx.xx.1 but not with 10.xx.xx.2 .
This means, all the DHCP requests are pointing towards the Gateway of the Data Center Switch.Is this the correct configuration?I have seen the Wireless Clients getting the IPs allocated from the DHCP Pool, even though the Management Interface's DHCP server configured with Gateway IP address 10.xx.xx.1 .
The DHCP configuration for the Data Center Switch is:
ip dhcp pool xxxxxx
network 10.164.220.0 255.255.254.0
default-router 10.164.220.1
The Management Interface configuration on the WLC is:
Interface Configuration
Interface Name................................... management
MAC Address...................................... 2c:54:2d:72:b5:40
IP Address....................................... 10.164.220.21
IP Netmask....................................... 255.255.254.0
IP Gateway....................................... 10.164.220.1
External NAT IP State............................ Disabled
[code]....
View 2 Replies
View Related
Jan 28, 2013
Basically I need to upgrade the license for Base-AP count to add 100 more AP's however my vendor has provided hardcopy of license as below:
-LIC-CT5508-UPG
-AIR-CAS-3KC-K9
-AIR-WIPS-AP-5
-L-NCS-1.0-100-ADD
My understanding is rigister LIC-CT5508-UPG/PAK number on cisco site and get .lic file however what is the use of other PAK where do i register this files with? Moreover , we do have NCS , MSE in place which is centralised devices.
View 2 Replies
View Related
Mar 28, 2012
we are observing the no. of conn thru asa 5580 is getting increased and one a fine day it will stop sending/receiving traffics.firewall# show conn count 1900000 in use, 2000008 most used As per the datasheet of this asa, the max conns permissible is 2 million (20 lacs). and the output shows that currently 1900000 connections are there and 2million+8 connections are most used.when i run " show local-host | include host|count/limit ", below are the outputs showing for max connections..
local host: <172.x.x.x>,
TCP flow count/limit = 35857/unlimited
TCP embryonic count to host = 25
UDP flow count/limit = 0/unlimited
local host: <DC01>, TCP flow count/limit = 306/unlimited TCP embryonic count to host = 8 UDP flow count/limit = 736807/unlimited
local host: <DC02>, TCP flow count/limit = 246/unlimited TCP embryonic count to host = 2 UDP flow count/limit = 582010/unlimited
local host: <172.y.y.y>, TCP flow count/limit = 1/unlimited TCP embryonic count to host = 0 UDP flow count/limit = 308412/unlimited
These are the top 4 connections, i wonder should we consider only the tcp flow count or udp as well ?
View 4 Replies
View Related
Sep 21, 2012
I have a 1905 series cisco router, when I run "sh int" command it gives me following details -
MTU 1500 bytes, BW 1544 Kbit/sec, DLY 20000 usec,
reliability 254/255, txload 7/255, rxload 151/255
Encapsulation PPP, LCP Open
Stopped: CDPCP
Open: IPCP, loopback not set
[code]....
let me know the significance of txload and rxload.This router is used for MPLS connectivity.Link is working OK..but I'm not able to understand exactly what is the above txload and rxload signify.There is also one peculiar phenomena occuring, when my reliability goes down then rxload also goes down or might be vise versa.
View 2 Replies
View Related
Dec 19, 2010
I have two sites with a dedicated, point to point, LAN, site 1 has a Cisco 1700, LAN IP: 192.168.0.101; Site 2 has a Cisco 1800, LAN IP: 192.168.1.101.From site 2 I can ping the router on the other side: 192.168.0.101, but nothing else on that network
From Site 1 I can't ping the other network at all,Both sites ping fine to their respective local interfaces. I also noticed, when trying to ping site 2 from 1, the "WIC ACT/CH" light blinks, otherwise it's off.
Site 1 has it's own web connection through COMCAST, site 2 is set to route through site's 1 connection to go out. The only thing the routers are doing are the actual connection between sites, and in the case of site 2, routing web traffic to 192.168.0.100, which is a Sonicwall on Site 1.
This was all working just fine, for a long time, up until yesterday, when the problem I described started happening.
View 1 Replies
View Related
Oct 1, 2011
The wan routers are 2600 and 1700. Conversions between the two? Pros/Cons of one versus the other? Regrets or horror stories for one versus the other?
View 3 Replies
View Related
Oct 23, 2012
I have an 1700 cisco Router and a ADSL connection to Internet.How may I use it on my home network?There's any configuration that I should to do?
View 3 Replies
View Related
