Cisco Switching/Routing :: How To Let Nexus 5548UP Act As DHCP Server

Nov 14, 2011

it's possible to let the Nexus 5548UP act as a DHCP server? (or if it will be possible in future releases)

View 3 Replies


ADVERTISEMENT

Cisco Switching/Routing :: Nexus 5548UP With 2232TM Fabric Extender And Server Teaming

Oct 11, 2012

Need clarification on the VPC with 5k and 2248 Fabric Extenders. My question  is can each fabric extender uplink to two different 5ks, and  at the same time, have servers connected to two both fabric extenders with a VPC.So basically, the server NIC will team with two different fabric extenders, and each fabric extender will connect to two different 5k's.

View 3 Replies View Related

Cisco Switching/Routing :: Nexus 5548UP VPC Configuration

Jan 26, 2012

I have followed every piece of cisco documentation I could find on this and I still can't get vPC configured to actually work.  The VLANs stay in a suspended state so no traffic flows across.  Below is my configuration:vrf context management  ip route 0.0.0.0/0 10.86.0.1vlan 1,vlan 86  name I.S_Infrastructure,vpc domain 1  role priority 1000  peer-keepalive destination 10.86.0.4,interface Vlan1,interface Vlan86  no shutdown  description I.S._Infrastructure  ip address 10.86.0.1/24,interface port-channel1  switchport mode trunk  vpc peer-link  spanning-tree port type normal,interface Ethernet1/1  switchport mode trunk  channel-group 1 mode active,interface Ethernet1/2  switchport mode trunk  channel-group 1 mode active ,interface Ethernet1/3,escription Connection to Mgmt0  switchport access vlan 86  speed 1000.

View 8 Replies View Related

Cisco Switching/Routing :: Change Airflow Of The Nexus 5548UP?

Aug 6, 2012

is it possible to change the airflow of the Nexus 5548UP in the field by replacing fan and power supply or must the correct airflow been ordered.

View 9 Replies View Related

Cisco Switching/Routing :: Nexus 5548UP / Two Management Interfaces For N5k

Jan 10, 2013

I have a Nexus 5548UP that would be managed by two organizations. Is it possible to set IP addresses for mgmt0 and an SVI (or an L3 interface) without using the L3 daughter card? I don't want to route between VLANs, just to separate management traffic.

View 4 Replies View Related

Cisco Switching/Routing :: Nexus 5548UP / L3 Cannot Do Inter-VRF Communications?

Aug 28, 2012

I'm trying to get a node in SVI1 on VRF1 to speak to another node in SVI2 on VRF2 to reach each other.  After hours of failure, I went to outside resources.  Everything I read on the internet says it's not possible on this platform and at least one TAC engineer seems to agree.
 
I just can't believe such a high-end data center switch is not capable of handling such a basic feature.

View 1 Replies View Related

Cisco Switching/Routing :: Replacing C4507R-E With Nexus 5548UP?

Jul 25, 2012

We currently have an environment with a 4507 as the core switch connected to four stacks of 3750e's in the wiring closets. A pair of Nexus 5548UP's also hangs off the 4507, but at the moment more or less dedicated to a certain purpose..The 5548UP's have the L3 daughter card installed.
 
My question is: Can a pair of Nexus 5548UP's do a C4507's job? Would we be able to decomission the 4507 and replace with the existing 5548UP's + FEXes?

View 1 Replies View Related

Cisco Switching/Routing :: Nexus 5548UP VPC Domain With 1x L3 Card

Apr 9, 2013

I can't find anywhere whether it is possible to create a vPC domain with 2 Nexus 5548UP switches, where only 1 Nexus 5548UP has a L3 daughter card.

View 3 Replies View Related

Cisco Switching/Routing :: Nexus 5548UP To 2248 Design

Aug 10, 2012

This past networkers I was at the Cisco booth discussing how the 2248 can connect to the 5548 and have server connectivity.  It was told to me that now, as of a fairly recent NX-OS release, you can have the 2248 going dual-homed to both 5548 via VPC and then have a server connected to both 2248 and be in active-active mode.  Is this correct?
 
When we first deployed our 5548 and 2248 we had to put the 2248 in a straight pin mode, where it only had connections to one 5548 and then the server would dual connect to the 2248's and be in active-active mode.  I was told that this changed with an NX-OS release however documentation still seems to be fragmented on what exactly is the case. 

View 3 Replies View Related

Cisco Switching/Routing :: Nexus 5548UP - Management Interface

Apr 21, 2013

How separate is the management interface on a Nexus 5548?
 
In context - what's the risk of having a layer 2 only Nx5K in a DMZ and running the managment ports down into an internal managment VLAN, to form peer-keepalive links and software upgrades.

View 4 Replies View Related

Cisco Switching/Routing :: Nexus 5548UP - FCoE QoS Configuration

Dec 6, 2012

I am looking to implement a QoS policy on a pair of Nexus 5548 UPs. FCoE is a factor here. I have created the following configuration and would like to get a few pairs of eyes to take a look at this for a quick sanity check.
 
How to make sure this config is valid. Also, I realize I'm applying an MTU of 9216 to all classes right now, this will be phased out incrementally.
 
class-map type qos match-all class-platinum
  match cos 5
class-map type qos match-all class-gold
  match cos 4
class-map type qos class-fcoe
  match cos 3
[code]....

View 1 Replies View Related

Cisco Switching/Routing :: Add 2 X Nexus 5548UP Switches At Site 1

Mar 5, 2013

I have 2 sites located approximately 30 kilometers apart.  I will call them site 1 and site 2.The sites are connected by a Layer 2 1GB fibre connection.I would like to add 2 X Cisco nexus 5548UP switches at site 1 and connect these 2 X Cisco nexus 5548UP switches via GLBP
 
I would then like to add 2 X Cisco nexus 5548UP switches at site 2 and connect these 2 X Cisco nexus 5548UP switches via GLBP.I would then like to connect the 2 X Cisco nexus 5548UP switches at site 1 and the 2 X Cisco nexus 5548UP switches at site 2 via GLBP.

View 3 Replies View Related

Cisco Switching/Routing :: Nexus 5548UP With L3 Card / Inter-VRF Not Possible?

Aug 28, 2012

I just received a Nexus 5548 to configure as the core of the Datacenter LAN.  Is it true that the VRFs created cannot talk to each other???  I can't seem to find any documentation on how to do this and at least one TAC engineer half-heartedly believes it's not possible, either.
 
Basically, I'm trying to get an SVI in VRF1 to be able to talk to an device on another SVI in VRF2.
 
I can't believe this high-end switch, that is so capable in every regard, cannot handle this feature.

View 1 Replies View Related

Cisco Switching/Routing :: Nexus 5548UP Switches - Load Balancing?

Mar 10, 2013

The best option for load balancing between 2 X Cisco nexus 5548UP switches located at one site and connecting to 2 X Cisco nexus 5548UP switches located at another site.
 
The sites are connected via a 1GB fibre connection. I am unable to use GLBP until GLBP is supported in further software releases.

View 1 Replies View Related

Cisco Switching/Routing :: LLDP Chassis Discovery On Nexus 5548UP?

May 1, 2012

I'm seeing several error messages like these in the logs of my Nexus 5548UP switches.

2012 Apr 24 16:39:41.470 SSV_5K_SW2 %LLDP-5-SERVER_ADDED: Server with Chassis ID aaaa.bbbb.cccc Port ID mgmt0 management address X.X.X.X discovered on local port mgmt0 in vlan 0 with enabled capability Bridge
 
2012 May  2 05:05:00.627 COR_CCO-NX-5548-UP_01 %LLDP-5-SERVER_REMOVED: Server with Chassis ID aaaa.bbbb.cccd Port ID aaaa.bbbb.cccc on local port Eth1/1 has been removed
 
2012 May  2 05:06:40.328 COR_CCO-NX-5548-UP_01 %LLDP-5-SERVER_ADDED: Server with Chassis ID aaaa.bbbb.cccd Port ID aaaa/bbbb.cccc management address NIL discovered on local port Eth1/1 in vlan 0 with enabled capability None
 
I will say that these 5548s are serving as the distribution layer for a UCS chassis (2x 6120 FIs) but didn't know what kind of visibility the Nexus would have into that - the chassis keyword is what's alluding to this in my mind, and I'm seeing these messages whenever interfaces that connect downstream to the fabric interconnects are brought up or down.

View 2 Replies View Related

Cisco Switching/Routing :: Nexus 5548UP Connectivity With Router 2811

Aug 15, 2012

In the existing network we have Cisco 2811 router connected to Corporate MPLS cloud. Cisco 2811 is connected to Catalyst 6509 switch(set based IOS with MSFC card). Along with that we have two Catalyst 5509. We are upgrading the access layer by replacing catalyst switches with Nexus 5548 & 2248.
 
For a purpose of testing I have connected 5548 & 2248. Created cPC and ether channels between two. SVI and HSRP configuredon 5548. I am terminating 2651 (test router) on 2248 port 101/1/1. On 5548 I have enabled EIGRP on vlans. I am unable to ping to 2651 from nexus switch 5548 and vice-versa. I can see both devices on CDP but I do not see eigrp neighborship formed.
 
What configuration should go in 2248 and 2651 in order to establish a connection between two? If test is successful then I will connect 2811 to 2248 during actual migration. I assume that in testing if it works for 2651 then it must work on 2811 router.

View 67 Replies View Related

Cisco Switching/Routing :: Nexus 5548UP Change Peer Keep Alive Link

Apr 19, 2013

I have a pair of Nexus 5548UPs that have some high priority servers running on them.  Servers are ESX hosts running Nexus 1000v's.  Each host has multple connections in a VPC to both 5548s.  We have been having intermittant ping loss and slowness of traffic to the VM's on these hosts.  I was poking around trying to figure out what the issue could be and found that the peer-keepalive command was not set to send the heart beat across the mgmt0 interface.  I would like to change this to point it accross the mgmt0 interface. Any tips or advice for me on making this change with production servers running on the switches?  I do not want to cause any loss to any systems when I make this change. [Code] ..........

View 3 Replies View Related

Cisco Switching/Routing :: Nexus 5548UP - (Physical Address Changes) Messages In SolarWinds

Dec 9, 2012

We have recently upgraded oor LAN and we are using couple of Nexus5548UP switches in the core with 2960 stacks as access switches. Each access switches stack is connnected to both core switches with link being port-chanels and VPCs. All is working fine, but our SolarWinds management platform (NPM) is being flooded with "Physical Address changed" events. Here is an example of messages:
 
NSW_Core_2 - Ethernet1/7 Physical Address changed from 000000003811 to 73616D653811
NSW_Core_2 - Ethernet1/7 Physical Address changed from 200B82B43811 to 000000003811
 
For each interface I have messages like these repeating.I am not sure what those messages means or if there is actually anything wrong. Performance of the network is good, there are no errors on any interfaces and I do not see anything related in the switch loggs.

View 4 Replies View Related

Cisco Switching/Routing :: Nexus 7018 Support Dhcp Server?

Oct 26, 2011

Can I configure a DHCP Servero on the Nexus 7018?

View 2 Replies View Related

Cisco Switching/Routing :: Enable Jumbo Frames On Single VLAN (Nexus 5548UP)

Sep 17, 2012

We are currently using two Nexus 5548UP's as our Datacenter Network Core.  I have a pretty simple objective:  I would like to enable Jumbo Frames on a single VLAN only(VLAN 65).  This VLAN is used strictly for backups.  I do not want to enable Jumbo Frames on the other VLANs(VLANs 1-10).  Im not sure what the best way to do this is.....or if it is even possible but I am hoping to get some configuration examples.

View 7 Replies View Related

Cisco Switching/Routing :: Nexus 7010 New Users Were Not Getting Ip Address From Dhcp Server

Jun 8, 2013

We  have 2 nexus 7010 switches configured with HSRP in the network. For all  the vlans core1 is Master and Core2 is standby. In the current setup we  have external dhcp server and dhcp relay is configured for all the  vlans on Master and standby switch. The setup is running the IOS 5.2
 
Activity Done: During  the Maintainacne activity, we isolated core1 switch in the network by  disabling the vpc/keepalive and all the uplinks from access switch. The  core2 switch was master for all the vlans.
 
Issue observed: It  has been observed that new users were not getting ip address from the  dhcp server. The ethereal capture showed that dhcp server was not  getting the dhcp requests from the core2 switch. We disabled the dhcp  feature in core2 and enabled again with dhcp relay again configured on  vlan interfaces .even after doing this no change was observed in  behaviour. Finally we got core1 back in network by enabling all the  links.
 
Observation: The  moment VPC link came up between the core switches, users started  getting ip's from dhcp. Then we started enabling all the uplinks on  core1.Core1 again become master for all the vlans and users continued  getting ip’s. Network running fine.
 
Further Testing

1. For  one of the vlan, core 2 switch has been made primary and for new users  checked the dhcp functionality and it was working fine. The aim was to  identify if anything wrong on core 2 related to dhcp relay

2.Again  we changed the priority for this vlan and made core1 master for the  same. This time we disabled this vlan on core1 and tried new user with  core 2 became master and dhcp functionality worked fine for new user.  Actually in this case we have simulated the same behaviour when we  observed the issue with only difference of VPC was not available during  the issue time as core 1 was isolated form network 
Inputs needed.

Is  there any known behaviour for dhcp functionality when VPC is  unavailable? If we see the test scenario2 (wherein core1 was master for  the vlan and we disable this vlan on core 1 and core 2 was able to relay  dhcp requests for new users in this vlan.) it was actually same as  scenario we observed during issue time..

View 7 Replies View Related

Cisco Switching/Routing :: Allowing DHCP / ARP Broadcast Through Nexus 3048TP?

May 8, 2013

I have a 3945 with a basic DHCP configuration applied to it. This 3945 is connected into one of the access ports of my nexus switch. I'd like to simply have the 3945 hand ip addresses out to other clients connected to the nexus switch. I have zero experience with nexus & haven't been able to turn much up through searching the net.

View 1 Replies View Related

Cisco Switching/Routing :: Nexus 7000 - Ip Dhcp Snooping Binding Table Is Empty?

Sep 14, 2010

I've configured ip dhcp snooping on several vlans I want to monitor and the binding table doesn't seem to be building.eature DHCP is on, global ip dhcp snooping is enabled, VLAN snooping is enabled on the vlan's I want to monitor and my trusted interfaces are also configured. Alas no binding entries in the table! 7K is running 4.2(6).

View 1 Replies View Related

Cisco :: Nexus 5548UP 2248TP To 3650G Vlan1 Trunking

Jun 4, 2012

Got an odd problem with trunking, all vlans except vlan1 trunk perfectly. Link is from a pair of dualhomed FEX 2248TP's to some 3650G Switches. Nexus running - version 5.1(3)N2(1) 3560's running - 12.2(53)SE2 & 15.0(1)SE2

View 3 Replies View Related

Cisco Switching/Routing :: Nexus 5k To 2k To 10gig Server Connectivity?

Nov 11, 2012

We are in the plan of implementing a new 10gig network. For this we have chosen the Nexus 5596 and 2232 pair. What are the transceivers/accesories I should order for connecting 10Gig servers of NC552SFP dual port NICs to the 2232 in High availability (NIC 1 to 2232PP 1 and NIC 2 to 2232PP 2). Should I order the FEX SFP+ uplink conector to conect 5k and 2232 also (or its aded to the Nexus box itself) ? Also, is it fine to have Nexus 2232 in floor 2 and Parent neus in Floor 3 (say seperatd by a max of 400meters)?

View 1 Replies View Related

Cisco Switching/Routing :: Nx 5548UP After Reboot Log Shows Vpc Down

May 23, 2013

We have a Nx5548up pair connected to FI6248 via a vPC. We had to reboot a FI (in order to configure more FC ports) ; following that reboot, we meet many issues.The first log shows the vPC down showing the FI rebbot.2013 May 23 12:31:45 sw-n5kup-fr-eqx-01 %ETH_PORT_CHANNEL-5 PORT_INDIVIDUAL_DOWN: individual port Ethernet1/2 is down

View 1 Replies View Related

Cisco Switching/Routing :: Nexus 5548 VPC To Dual NIC Server With LACP

Apr 1, 2012

We are planning to have attach topology with nexus 5548 using vpc. Let me know if this i possible. I want to configure dual NIC linux server using LACP active mode to connect to two 5548 in VPC for redudancy as well as use of full access layer bandwidth. On nexus this will be access port in single port channel in single VPC link.

View 1 Replies View Related

Cisco Switching/Routing :: Configure New Server With Nexus 5548 Switch

Jul 15, 2012

My Name is senthil i need to configure new hp sever with Nexus 5548 how to config.. server side everything finished just i need only
 
Config tips for Nexus 5k for New server

View 2 Replies View Related

Cisco Switching/Routing :: Nexus 7009 Need To Configure DCNM Server To Get License

Jun 18, 2012

We've gotten two Nexus 7009's in and I'm starting to configure them when I found I couldn't add VDCs.  I found there was no license installed but the only licenses I found that came with them are "Cisco DCNM for LAN Enterprise Lic for one Nexus 7000 Chassis".  So my question is this - do I need to configure a DCNM server to get the license pushed to these two 7009s or should there be another PAK for each chassis that I can register and get my enterprise services?

View 1 Replies View Related

Cisco Switching/Routing :: 1941W No IP From DHCP Server With Ip-helper

Jun 12, 2013

I've a Cisco 1941W router which is DHCP server for data-VLANs and uses ip-helper for voice-VLANs. [code] I don't know why I can't have IP from wireless voice VLAN whereas it is OK and wired voice VLAN and conf is the same!

View 4 Replies View Related

Cisco Switching/Routing :: Configure 881 Router To Act As DHCP Server?

Jul 9, 2012

Is it possible to configure an 881 router to act as a DHCP server to 4 VLAN's each with a different scopes all through a single ethernet interface? 

View 2 Replies View Related

Cisco Switching/Routing :: DHCP Server Catalyst 3750

May 28, 2013

I have customer who has as Core Switch one Cisco Catalyst 3750 with the IOS c3750-ipbase-mz.122-35.SE5.I know that this image support DHCP Server configuration, but I like to implementate new vlans (approx 15) and I want to know if this switch support 15 DHCP Servers.

View 3 Replies View Related

Cisco Switching/Routing :: 861 Need DHCP Server With Static IP Addresses

Feb 2, 2013

I used to use a CentOS self-made server for intranet for my little office, but I bouth few days ago a Cisco 861 router to replace the linux box.
 
1. I have 2 public IP classes from my ISP. 1 class is limitted to 80mbit upload, the other to 30mbit upload. So I need some sort of DNAT to be able to know exactly which intranet computer uses big internet and which one limitted internet.
2. I need DHCP server and with static IP addresses (one computer must always have the same IP address, etc).. i have my needs for this.
3. Also I need external access to some servers inside (web, ftp, etc) [code]
 
So far so good, all looks simple and I can achieve this in 2 hours on a centos linux box (correct routes, ip forwarding enabled and few iptables rules for NAT/SNAT/DNAT).
 
But on this brand new Centos router well, i'm not even successful in pinging the outside world, nor the inside world I'm tired of reading the forums, the documentation..i want (at first) a simple scenario: vlan+dhcp, fa4 with 1 public ip address and ACCESS to the real world. I wasn't able to achieve not even that much. [code]

View 6 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved