Cisco :: Unable To Save Topology Maps LMS 2.2
Feb 21, 2005
I have users that are unable to save their changes to topology maps - when devices are moved in a map and the map is exited, the next time the user goes into the map it is back at the default layout. The unusual part is that this does not affect all users - I have two users with the same CiscoWorks rights, but only one can save map changes. The admin user is one that can't save map changes. I'm running LMS 2.2 on Solaris 2.8. The problem existed before and after I upgraded to Campus Manager IDU 11, and stopping and starting services hasn't worked.
View 7 Replies
ADVERTISEMENT
Mar 21, 2013
I have to build a MESH topology with 1 Root Access Point and 4 Mesh Access Points which are 1552E.I have a wireless controller which is a WiSM 2 card into a 6500 chassis.I want to know if there is a pre-configuration to do on the AP before installing it, or if they are automaticaly discovered by controller (even for MESH AP which are NOT wired to LAN) ?
View 15 Replies
View Related
Nov 7, 2011
When i try to launch topology services in LMS 4.0 i get prompted to install a java plugin. When i install this it tells me to restart the browser but nothing is changed, it asks me if i want to install the java plugin again.
View 7 Replies
View Related
Mar 11, 2013
Im having trouble with the topology service. Java is installed, but i cant start the topology service.
View 7 Replies
View Related
Sep 26, 2012
I have ASA 5505 and I save the configuration in the ASA 5505 using write memory or using copy run start but whe i unplug the power cord and plug it back in the ASA gets its factory default configuration.
View 8 Replies
View Related
Jul 4, 2012
I have a 3750 stack of 4 switches that was installed about 2 years ago. Recently I was doing some work on the switch and realized that I am unable to save the config. I amobviously concerned that if the power fails or the switch reboots I will be reconfiguring it and that is not something I am interested in doing!
[code]...
View 1 Replies
View Related
Apr 1, 2013
Due to problems with the D view cam, I have reset my IP camera DCS-930L but I can't register the password, it says "There was a problem saving your settings. Press next and try again." I can't get pass saving password, tried all the previous passwords but none works.
View 2 Replies
View Related
Jul 4, 2012
I have a 3750 stack of 4 switches that was installed about 2 years ago. Recently I was doing some work on the switch and realized that I am unable to save the config. I amobviously concerned that if the power fails or the switch reboots I will be reconfiguring it and that is not something I am interested in doing!
Here is the error that I am receiving:
switch#copy run startup-config
Destination filename [startup-config]?
Building configuration.
View 11 Replies
View Related
Jan 24, 2012
We are facing problem with cisco 6506 switch while configuring when we try to save it, we are not able to save the config, neither we are able to view running and startup config.
View 2 Replies
View Related
Mar 11, 2013
I have a user that is trying to save an excel speadsheet that is located in a shared folder on a server, the user can open the file and edit ok but when they try to save the file the progress bar pops up but just hangs then a message pops up to saying "file not saved". They are using Windows 7.The user is new and I have just set up their account so thought it might be permission issues but I have logged the user in on two other different machines (1 win7 and 1 WinXP) and they have no problem at all.
View 7 Replies
View Related
Sep 3, 2011
I'm working on a practice lab and am having the following issue. I have a customer router connected to two different ISP routers. Each ISP router must advertise a default through BGP to the customer and one of the default routes must be preferred over the other. Given if the preferred route interface is shut down the other default route is inserted into the routing table and when the preferred default route interface it turned back on that path is used again. The catch is I cant alter the customer router only the the two ISP devices. I tried doing some route maps but I'm lost. I have deleted all my route maps and have posted the BGP portion of the ISP routers.
router bgp 300
no synchronization
bgp log-neighbor-changes
[Code]....
View 13 Replies
View Related
May 22, 2013
This is to see if I am the only one disappointed with the Mapping portion of Cisco Prime Infrastructure: my disappointments are as follows: The Map can only be zoomed up to a certain size, under WCS and NCS we could almost zoom indefinitely into the map.2. The edit map sizing tool bit and its working has changed and quite difficult to use, the tool tip has changed into a small square, and uses double click which are not as intuitive as before, why change a working thing?3. Printing the Map is almost like priting the screen, when you say print you are telling it to print the map and not how it appears on your screen, for there are other tools like snagit or greenshot.
View 1 Replies
View Related
Dec 6, 2012
I have the following set up, at one of our sites:What I would like to do is take non 10.x.x.x web traffic, and pipe it through the ISP2 link, and keep all other 10.x.x.x traffic over the main ISP1 link. I would like to set this up on the L3 3750's that we have. Here is my configuration for the 3750's (IP's have been changed for security):
track 222 ip sla 222 reachability
track 223 ip sla 223 reachability
ip access-list extended INTERNETTRAFFIC
permit tcp 10.1.1.0 0.0.1.255 any eq www - Internet LAN subnet
permit tcp any 10.1.1.0 0.0.1.255 eq www
permit tcp any eq www 10.1.1.0 0.0.1.255
[code]....
I'm applying the policy route-map to the VLAN interface, but do not see any traffic, once I apply the interface. I'm not that experienced, with route-maps?
View 2 Replies
View Related
Feb 18, 2011
I have a network architecture like the one HERE but with alot more spokes (32). Would my cisco 3925 be able to support so many crypto maps?
View 2 Replies
View Related
Aug 21, 2012
I'm currently looking at doing some re-design work for a platform we manage on the ACE.I want to be able to run a single VIP and only do a sticky session based around specific URL's not all. I've got the following configuration to apply a sticky session to a URL. [code]Notice, under the Policy-map type loadbalance http first-match WEB-POLICY-L7 i have two class statements, one that matches the URL L7 policy and applies a sticky farm and the second class falls into the default.Am i right in saying with this configuration, any http traffic hitting the VIP 192.168.1.1 that does NOT match /urltobedefined.co.uk/test sticky sessions are NOT applied. But traffic hitting 192.168.1.1 that does match /urltobedefined.co.uk/test will apply the sticky policy?
View 2 Replies
View Related
Feb 16, 2012
I have a 3750 switch and I am trying to configure PBR (route-maps) in it.But when I try to apply the policy to a vlan interface the policy does not show in the interface.So I can not use PBR to choose my default gateway!Question: Does PBR work in a 3750 switch? Can PBR be configured in a vlan interface? There is any problem with the IOS that I do not know?
View 5 Replies
View Related
Feb 6, 2013
I have a Cisco 3750 stack with 5 members.
Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
1 24 WS-C3750G-24T 12.2(55)SE6 C3750-IPSERVICESK9-M
2 24 WS-C3750G-24T 12.2(55)SE6 C3750-IPSERVICESK9-M
* 3 24 WS-C3750G-24T 12.2(55)SE6 C3750-IPSERVICESK9-M
4 52 WS-C3750G-48TS 12.2(55)SE6 C3750-IPSERVICESK9-M
5 52 WS-C3750G-48TS 12.2(55)SE6 C3750-IPSERVICESK9-M
I have recently set the sdm prefer template to routing to allow route-maps and rebooted the stack:
3750GCORE#show sdm preferThe current template is "desktop routing" template.The selected template optimizes the resources inthe switch to support this level of features for8 routed interfaces and 1024 VLANs.
number of unicast mac addresses: 3K number of IPv4 IGMP groups + multicast routes: 1K number of IPv4 unicast routes: 11K number of directly-connected IPv4 hosts: 3K number of indirect IPv4 routes: 8K number of IPv4 policy based routing aces: 0.5K number of IPv4/MAC qos aces: 0.5K number of IPv4/MAC security aces: 1K
I still cannot apply a route map to a vlan interface however:
I have preconfigured the route map as per below to take traffic from one particular client and pass it to the inside interface of our ASA firewall:(yes i know 192.9.0.0 is a public network, its an inherited problem that is in process of being remedied!)
ip access-list extended TEST
permit ip host 192.9.216.234 any
permit icmp host 192.9.216.234 any
permit tcp host 192.9.216.234 any
route-map TEST_MAP permit 9
match ip address TEST
set ip default next-hop 192.9.201.10
When i do the following I get this error from debug:
3750GCORE#config t
Enter configuration commands, one per line. End with CNTL/Z.
3750GCORE(config)#int vlan 216
3750GCORE(config-if)#ip policy route-map TEST_MAP
3750GCORE(config-if)#
007804: Feb 8 03:16:55: %PLATFORM_PBR-3-UNSUPPORTED_RMAP: Route-map TEST_MAP not supported for Policy-Based Routing
when I show the running config, the route-map is not there.3750GCORE#show running-config int vlan 216Building configuration...Current configuration : 205 bytes!interface Vlan216
no ip redirectsip directed-broadcast 101end
why TEST_MAP is not supported?
View 2 Replies
View Related
Aug 4, 2009
Basically I have an internet router (1841ISR) with 1 internal (LAN) connection and 2 internet connections. What I want to do is route specific traffic for 3 of my internally hosted services (smtp, https, etc) through one internet connection (fa0/0) and then route all other traffic through the unmanaged/dynamic IP ADSL connection (Dialer 0).
View 9 Replies
View Related
Jul 18, 2011
I have a requirement to provide stats on a per-department, per-destination basis between sites. If I take Voice as an example I have 5 child classes referring to the 5 departments each matching EF and a particular access-list that matches the department's subnet. I tie these 5 child classes into a parent Voice class-map.
Now when I issue a "show policy-map interface" command I see stats for the parent class-map only whereas I would expect to see a breakdown for each of the child classes which is what is required.
I am doing this on an ASR1002 running 3.2.2.
View 1 Replies
View Related
Mar 26, 2013
I got myself lately Cisco SR520 router with some basic firewall functions built in. This is going to be used for my home broadband, so no need to be really super secure, as it would be for some business. I managed to configure it, however there are few things on the firewall side, which I don't understand.
This router had some default configuration in it's flash, when I bought it. There are class maps.... how it works or how to add/edit rules. Also, do I need to use class maps, or can they be replaced by ACL's to certain extend? How to add/edit class maps rules to allow certain port (eg. 3333). Pease see below part of the default config:
class-map type inspect match-any SDM-Voice-permit
match protocol sip
class-map type inspect match-any sdm-cls-icmp-access
match protocol icmp
match protocol tcp
[Code]...
View 1 Replies
View Related
Jul 15, 2012
I'm trying wrap my head around bandwidth guarantee for nested maps. I tried adding a new class to two of my policy-maps today, and got this error: 3945E-1(config-pmap-c)#bandwidth 3000 Insufficient bandwidth 3000 kbps for the bandwidth guarantee
I'm not sure how it knows that with the nested maps and how it's computed. I have a 100mb WAN connectin going to 19 branches. I have a class-map that identifies traffic to the individual branch and within that class, a policy-map is applied to prioritize voice over video etc.
Here's the QoS setup:
class-map Branch1-Policy
match access-group branch-1-acl
*
*
[code]....
I was adding the Video-Conf class to both Traffic-6calls and Traffic-10calls when I got the above error. How would that percentage be calculated? I know by default i can only reserve up to 75% of interface bandwidth. The platform is 3945E running 15.1(3)
View 1 Replies
View Related
Jan 16, 2012
I'm trying to configure a zone-based firewall on an SR520 and am confused about the 'not' criterion. The 'zone-design-guide' says (my stress): Class- maps define the traffic that the firewall selects for policy application. Layer 4 class-maps sort the traffic based on these criteria listed here. These criteria are specified using the match.where my intention is to let only LAN hosts with IPs in the range 192.168.1.1 to 192.168.1.7 out through the firewall. There may be an easier way of doing this which I'd be pleased to hear about. But, even if there is, I'd also be interested to know what I'm doing wrong in the above.
View 0 Replies
View Related
Sep 6, 2012
Im having a (from google-fu) seemingly unique issue with load balancing. So for background, I am running the ACE 4710 device in "on a stick" mode, so I am using NAT and all that good stuff. I am also utilizing class maps and host header matching so I can save on IP space. [code]
Basically, as soon as I add that ACL_CLASS_beta.mainsite.com class map, all I get back from the ACE is RST packets and it comes back with an L7 LB Policy Miss.
It SEEMS like it should work, but it doesnt seem to like matching on those source addresses at all.
View 1 Replies
View Related
Jan 28, 2013
With à customer we have à site to site VPN connection. In this tunnel there is one subnet routed with a 3des-sha encryption / hash. Now the want to add a new subnet in this tunnel, but with a AES-128 / MD5 encryption / hash. Is it correct if we make a new crypto map with a higher seq. number?
View 5 Replies
View Related
Mar 20, 2012
i have an issue with the lms 4.2 Topology Data Collection. After installation the Topology Data Collection was running normaly, but since first server reload the Topo Data Collect under Inventory > Dashboards > Device Status > Collection Summary is "frozen".Is there any option to stop this process elsewhere? I cannot find anything under jobs in running state or so. Clicking on Schedule only give me the option to start data collection, but lms always returns that the process is running.
View 9 Replies
View Related
Nov 26, 2012
1)i have problem in LMS 4.2 , he shows most devices not connected to topology sitting lonly even though the have cdp enable , how to force these to join the topology
2)why some devices are shown unreachable , even though i can ping them from lms server and gets reply, also they have community and cdp configured
View 1 Replies
View Related
Dec 19, 2011
On a LMS 4.0.1 :I want to know what is the right way to change the telnet program on the campus mgr map (topology services map), when right-clicking a device icon and selecting telnet.I would like to use a tool of mine, and not to launch a telnet command from the IE browser.I changed the default telnet of Windows in the registry, but the program is still launched as a telnet URL in the browser and this is not what I would like to do.
View 2 Replies
View Related
Mar 12, 2012
The regular problem with the LMS topology and WAN Links when you see the branches are disconnected from the HQ BUT in my case the branches are already connected via Layer2 links but unfortunately some intermediate layer2 modem/switch exist in some branches which prevent CDP discovery but you will find both HQ and branch router in the same subnet .
View 1 Replies
View Related
Jun 20, 2012
i have only 1 switch 2960 POE at customer enviroment.i did run topology service and checked on the right side POE CAPABLE Devices
it shows me that i have 4 switch POE while actually there is only 1 switch POE in real enviroment.
View 7 Replies
View Related
Feb 4, 2012
have ether-channel across 2 switches?i am new in cisco LMS . now i am in client site installing cisco LMS 4.1 in UCS server-rack version. we did it well for the installation, and the LMS working properly until i cannot open topology service.
i attached the error message
View 14 Replies
View Related
Feb 14, 2012
I have a customer who wants to disable cdp on all switches for securtity reasons. The same customer has also LMS 4.0 installed.
When disabling cdp, does it affect the topology services on LMS? Can you still see the topology tab on device manager or the topology map of the entire network?
View 4 Replies
View Related
Oct 13, 2012
I config the routers with EIGRP and also write Static route between two PC before remove the link between router0 and router1 , destination is reachable , but when remove this connection , packet from pc1 to pc0 will drop in a loop and never reach to destination , is it possible to have a Link state routing protocol and static route at the same network like this scenario , how to prevent loop in this topology static route is configure as bellow :
router0 <==> router 1 <==> router2 <==> router3 <==> router <==>pc1
View 6 Replies
View Related
Jun 12, 2012
I have problem with topology view in LMS 4.2.1, it doesn't show the tunnels connecting branches, though both devices are shown in sh cdp neighbour command output. If I choose Show Devices in Admin > Collection Settings > Data Collection, it is showing cdp neighbours correctly.
View 4 Replies
View Related
