Cisco VPN :: 1941 - How To Make Remote Clients To Access Third Party IP Address
May 23, 2013
I've got a Cisco 1941 setup working fine for Cisco Anyconnect. Clients can connect to local resources fine. The issue I have is I need the remote clients to access a third party IP address but to do so they must do it through the VPN. At the moment only local resources are accessed across the vpn and if they need internet they use their own internet connection they are connecting with.I've added the below to make sure traffic going to the IP is going across the VPN.
View 4 Replies
ADVERTISEMENT
Feb 12, 2013
Im facing with some DHCP lease issue and its like this,Our Cisco 2951 edge router is configured with local dhcp pool for a set of remote users when they connect through Cisco VPN which was working fine until we planned to change it to a Windows box that is configured for DHCP.The basic idea now is to relay the DHCP requests that are coming from the remote clients through Cisco VPN to the DHCP Windows server. So we added the scope on the server and changed the client config on the router as follows (highlighted is the dhcp relay config). [code]
View 1 Replies
View Related
Dec 12, 2012
I have 2 site here:
site A
Cisco 891
external IP: 195.xxx.yyy.zzz
VPN Gateway for Remote users
[Code]....
View 1 Replies
View Related
Dec 12, 2011
I have 2 sites :
site A :
ASA 5510
VPN gateway for remote users
LAN 192.168.192.0/22
site B :
ASA 5505
LAN 192.168.208.0/22
Both sites are connected through a site to site VPN.Remote clients (AnyConnect/VPN client) can connect to Site A LAN and see machines on LAN A but cannot see Site B LAN.
Here is a part of my configuration :
On Site A (ASA 5510)
--------------------------------
name 192.168.192.0 SiteA_Internal_Network
name 192.168.208.0 SiteB_Internal_Network
name 192.168.133.0 VPNPool_AnyConnect
name 192.168.133.32 VPNPool_VpnClient
[code]....
View 9 Replies
View Related
Oct 24, 2012
I have an ASA 5520 8.2(3) and allowing my remote client-to-site-vpn clients to access resources directly connected to my ASA on separate lower security interfaces (not the outside) besides just clients on my internal networks. Someone mentioned to me configuring 'VPN on a stick' however from what I've read this seems to be only applicable when it comes to split-tunneling back out the outside interface (could be off on that). Is this possible on other lower security interfaces as well, and if so what would a mock config that accomplishes that look like (acl's, nat, etc)? Also, if I want internal users to be able to connect to these remote clients once they are active, are there any nat statements necessary (such as nonatting them) or are the vpn clients just seen as internal clients from the rest of the internal network's standpoint by default?
View 5 Replies
View Related
Dec 13, 2012
I am setting up a new remote access VPN using the traditional IPSec client via ASA 5515-X runnning OS 8.6.1(5). We require to provide each client multiple DNS suffixes, but are only to provide a single DNS suffix in the group policy.I have tested using an external DHCP server, but using our Windows Server 2008 infrastructure and Option 119 the list is not provided to clients, and I have read that Windows 7 clients may ignore this option anyway.
View 0 Replies
View Related
Jul 25, 2011
I have a RV082 and several of my remote laptops cannot access my server using its domain name. It can be accessed using its internal ip address. The issue is that you can log onto the server using remote access and the ip however you cannot use any shortcuts using the domain name. You can see the server with the domin name however no access path is available. This is only on a few remote user laptops. Others work perfectly.
View 1 Replies
View Related
Apr 15, 2012
I have been asked to set up remote access VPN on an ASA 5505 that I previously had no invlovement with. I have set it up the VPN using the wizard, they way I normally do, but the clients have no access to anything in the inside subnet, not even the inside interface IP address of the ASA. Thay can ping each other. The remote access policy below that I am working on is labeled VPNPHONE, address pool 172.16.20.1-10. I do not need split tunneling to be enabled. The active WAN interface is the one labeled outside_cable. [code]
View 1 Replies
View Related
Sep 6, 2012
Just installed ASA -5505 replaced cisco 851
My exchange server hosts remote outlook clients and remote web access
no one on the remote side can access my exchange server
internal mail flows in bound and out bound.
My iphone can not access the exchange server either.
When the Cisco 851 was online all the above worked great. Nothing changed on the remote client side just put the ASA 5505 in service.
I am new to the ASSA 5505 family. Had a reseller configure the router but unable to get them at this hour. Called Cisco support but they are closed at this time also.
View 5 Replies
View Related
Mar 31, 2013
I am not sure if what I am trying to accomplish is possible. On my internal network I have the following VLANs setup (102, 104, 106) and they map one to one to a subnet (ie: 102 = 192.168.102.0/23, 104 = 192.168.104.0/24, etc).All interVLAN routing is done on a 3560 via vlan SVI. Connected to the 3560 via a routed port is a ASA 5510. The routed port has IP 192.168.100.1 and the ASA interface on the other side of that routed port has IP 192.168.100.2. I use 802.1x on the wired network to assign users (based on their department) into a specific VLAN. I want to extend this concept to Remote VPN access. Therefore I setup multiple Group Policies (policy is applied based on an LDAP attribute) where each policy defines a different DHCP scope. This has successfully allowed me to login wtih different users who get assigned to different Group policies and they obtain the correct DHCP IP address from the internal DHCP server (ie: an engineering person logins remotely and gets an IP in 192.168.102.0 range). However the issue (and as I was planning this out I knew this would come up) is that traffic can be routed out from the VPN client to its destination but there is no return path.
View 3 Replies
View Related
Jul 1, 2012
I setup ASA5540 for SSL-VPN (clientless) works fine. But I try to use Client (AnyConnect) to access internal resources, it is failed. It is stiil initiate sessions from remote client IP. I need to initiate session from client IP assigned by ASA5540 box (same with Cisco VPN client connect to Cat65 SVC module). How I setup it?
View 3 Replies
View Related
Jan 24, 2013
We've got vpn-concentrator and 15 offices with 881w and 1941 isr connected vo it via ipsec. Our Asterisk is placed behind this vpn-concentrator in local network, so all traffice goes throung vpn tunnels. Is it possible to make QoS rules using just destination IP address of our Asterisk server?
View 7 Replies
View Related
Mar 27, 2012
i have Cisco 1941(with security lic) and i have been asked to make a VPN with public IP addresses so there will be no info about internal networks. Other side has ASA 5520 and they provided me with 2 public IP addresses. i have done many different VPNs but this is first with public IP addresses and i cannot figure it out.So here is the question:
1. How to do it ? (maybe some example)
2. Do i need two public IPs to do it ?
View 1 Replies
View Related
Sep 12, 2012
We have two ASA 5500 series Firewalls running 8.4(1). One in New York, another in Atlanta.They are configured identically for simple IPSecV1 remote access for clients. Authentication is performed by an Radius server local to each site.
There are multiple IPSec Site-to-Site tunnels on these ASA's as well but those are not affected by the issues we're having.First, let me start with the famous last words, NOTHING WAS CHANGED.
All of a sudden, we were getting reports of remote users to the Atlanta ASA timing out when trying to bring up the tunnel. They would get prompted for their ID/Password, then nothing until it times out.Sames users going to the NY ASA are fine.After extensive troubleshooting, here is what I've discovered. Remote clients will authenticate fine to the Atlanta Firewall ONLY IF THEY ARE USING A WIRED CONNECTION.
If they are using the wireless adapter for their client machine, they will get stuck trying to login to Atlanta.These same clients will get into the New York ASA with no problems using wired or wireless connections.Windows 7 clients use the Shrewsoft VPN client and Mac clients use the Cisco VPN client. They BOTH BEHAVE the same way and fail to connect to the Atlanta ASA if they use their wireless adapter to initiate the connection.
Using myself as an example.
1. On my home Win 7 laptop using wireless, I can connect to the NY ASA with no issues.
2. The same creditials USED to work for Atlanta as well but have now stopped working. I get stuck until it times out.
3. I run a wire from my laptop to the FiOS router, then try again using the same credentials to Atlanta and I get RIGHT IN.
This makes absolutely no sense to me. Why would the far end of the cloud care if I have a wired or wireless network adapter? I should just be an IP address right? Again, this is beyond my scope of knowledge.We've rebuilt and moved the Radius server to another host in Atlanta in our attempts to troubleshoot to no avail. We've also rebooted the Atlanta Firewall and nothing changed.
We've tried all sorts of remote client combinations. Wireless Internet access points from different carriers (Clear, Verizon, Sprint) all exhibit the same behavior. Once I plug the laptops into a wired connection, BAM, they work connecting to Atlanta. The New York ASA is fine for wired and wireless connections. Same with some other remote office locations that we have.
Below I've detailed the syslog sequence on the Atlanta ASA for both a working wired remote connection and a failed wireless connection. At first we thought the AAA/Radius server was rejecting us but is shows the same reject message for the working connection. Again, both MAC and Windows clients show the same sequence.Where the connection fails is the "IKE Phase 1" process.
-------------------------------------------------------------------------------------------------------------------------
WORKING CONNECTION
-------------------------------------------------------------------------------------------------------------------------
%ASA-6-713172: Automatic NAT Detection Status: Remote end is|is not behind a NAT device This end is|is not behind a NAT device
NAT-Traversal auto-detected NAT.
%ASA-6-113004: AAA user aaa_type Successful: server = server_IP_address, User = user
%ASA-6-113005: AAA user authentication Rejected: reason = string: server = server_IP_address, User = user
[code]...
View 1 Replies
View Related
Sep 5, 2012
i now learning about SSLVPN, and i already install license in 1941 with SSL and security9 License, i learning how to make a gateway for SSLVPN full tunnel, but i meet an obstacles, when i go to my wan ip address https://wan ip address, the browser give this
SSL connection error Unable to make a secure connection to the server. This may be a problem with the server, or it may be requiring a client authentication certificate that you don't have.
Error 107 (net::ERR_SSL_PROTOCOL_ERROR): SSL protocol error
[code]...
View 1 Replies
View Related
Mar 29, 2013
I need to setup a system where my staff can access the internet using the IP address at my buisness. IE. My staff can log into our marketing software (which will only allow access from my buisnesses IP address) from home. My thoughts were to leave the computer on at work all the time and then use a remote access program like logmein to remotley control that computer however I am then limited by only having one person able to do this at a time. I want to be able to use my buisness internet connection as a proxy as such....i think? Computers are running windows 7. Buisnesses internet connection is DSL with wireless modem
View 3 Replies
View Related
Mar 17, 2013
Is the following sysntax correct in removing a remote access vpn address pool and inserting a new one on an ASA5510?
(config)# NO ip local pool BWCVPN 192.168.200.1-192.168.200.128
(config)# ip local pool BWCVPN 192.168.300.1-192.168.300.128
(confif)# tunnel-group BWCVPN ciscovpn general-attributes
(config-general)# address-pool BWCVPN
View 5 Replies
View Related
Sep 15, 2011
At first I use ACS 4.2 to create static ip address user for remote access VPN,It's easy,just configuration it at user set>Client IP Address Assignment>Assign static IP address,but when I use ACS 5.2 I can't find it.I try to add IPv4 address attribute to user by read "ACS 5.2 user guide" ,it says this: [code] I do this,but it's not work.When I use EasyVPN client to connect ASA 5520,user could through authentication but will not get that static IP address which I configuration on Internal Users.so,what should I do,if anyboby knows how to use ACS 5.2 to create a static ip address user for remote access VPN.
View 2 Replies
View Related
Sep 7, 2011
I'm trying to achieve framed-ip-address/static ip address for some remote access vpn clients and ip allocation from pool dynamically for remaining remote access vpn clients. I've configured my asa [URL].
I'm using local database for user authentication. Remote users can connect and always gets IP address from pool only and never gets the framed-ip I configured for those particular users.
View 3 Replies
View Related
Sep 17, 2011
At first I use ACS 4.2 to create static ip address user for remote access VPN,It's easy,just configuration it at user set>Client IP Address Assignment>Assign static IP address,but when I use ACS 5.2 I dont't know how to do it.
I try to add IPv4 address attribute to user by read "ACS 5.2 user guide" ,it says this:
Step 1Add a static IP attribute to internal user attribute dictionary:
Step 2Select System Administration > Configuration > Dictionaries > Identity > Internal Users.
Step 3Click Create.
Step 4Add static IP attribute.
Step 5Select Users and Identity Stores > Internal Identity Stores > Users.
Step 6Click Create.
Step 7Edit the static IP attribute of the user.
I just do it,but it's not work.When I use EasyVPN client to connect ASA 5520,user could success to authentication but will not get the static IP address which I configure on Internal Users,so the tunnel set up failed.I try to Configure a IP pool on ASA for ACS users get IP address,and use EasyVPN client to connect ASA , everything is OK,user authenticate successed.but when I kill IP pool coufigurations and use the "add a static IP address to user "configurations,EzVPN are failed. how to use ACS 5.2 to create a static ip address user for remote access VPN?
View 7 Replies
View Related
Nov 15, 2012
I have windows 7 clients (supplicants), D-link access point (authenticator), Cisco acs 5.2 virtual appliance with evalution license (acts as authentication server - Radius server). I want to setup EAP authentication (PEAP) that users will be able connect to Wireless LAN with login-password. I've done some configurations, but I did not get any result. in ACS 5.2 I get this error message: 11014 RADIUS packet contains invalid attribute(s): RADIUS Request dropped.
View 5 Replies
View Related
Sep 17, 2012
Accessing exteral address internally.
I have a mail server, with external access which works fine for external access thorugh our router (a 1941). I have a laptop which connects to a wireless network that is inside our router. When attempting to navigate to the webmail or use outlook, it cannot connect.
The laptop is configured to access the mail through the external path as it would be offsite occasionally.
I think the problem seems to be that the traffic is not leaving the router to come back internally. The laptop can ping the external address ok.
I read about something called hairpinning - is this what i need to be looking at?
View 3 Replies
View Related
May 4, 2012
I have 5 workstations with 2 servers but the backup server (black) is shut down intentionally.I have 1 cisco gigabit unmanaged 8 port switch and 1 cisco 1941 vpn router.The cisco 1941 vpn router is configured for IPVPN connection to other branches.
Challenge:
1. Configure NAT to enable the 5 workstations to be connected to the internet thru the router to the ISP.
2. Configure NAT to enable the server to be accessed from outside using the public IP address provided by the ISP. [code]
Verification:
1. I can ping other pc on 10.71.5.0/24 network.
2. When I typed in the ISP's public ip address on the browser, i got into the modem user interface for configuration.
I still can't connect to the internet. When i do tracert, it stops on the 192.168.15.1 hop and didnt continue. This shouldn't be the case since i want to connect using the GE0/1 outside port for the internet.
View 6 Replies
View Related
Mar 30, 2013
I've some strange problems with multiple ASA (NEM) VPN remote clients (v8.4.5). On the HQ I've an ASA5510 (v8.4.5) with multiple NEM's connected to it. The group policy used on the HQ is configured for split tunneling. Now here's the problem;
The remote ASA (NEM) constructs easily a VPN connection to the main location; it seems that everything works well. Traffic through most of the tunneled networks works perfectly. Traffic to certain subnets or hosts brings me into trouble, there is no traffic flowing through the tunnel at all!
When using the command "show crypto ipsec sa | i caps|ident|spi” I can see all of the tunneled subnets. The subnets that works perfecly gives me the correct "local and remote ident" output. The subnets with problems gives me wrong values in the "remote ident". The remote ident should be the IP address of the inside LAN (of the remote NEM) and not the IP address of the ouside interface (of the remote NEM). How is this posible?
Here's is the crypto ipsec sa output:
Result of the command: "show crypto ipsec sa | i caps|ident|spi"
local ident (addr/mask/prot/port): (10.200.60.0/255.255.255.0/0/0) <-- this is the good subnet of the inside interface (NEM)
remote ident (addr/mask/prot/port): (10.100.2.2/255.255.255.255/0/0) <-- this is the good subnet (HQ)
#pkts encaps: 54712, #pkts encrypt: 54712, #pkts digest: 54712
#pkts decaps: 31893, #pkts decrypt: 31893, #pkts verify: 31893
#PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
current outbound spi: A4FA947A
[code]....
View 1 Replies
View Related
Aug 9, 2011
I am using Cisco 2911 router , i configured remote client in that . i need to provide the static ip to the remote users instead of providing from the dhcp pool. is it possible? if it is how we can do that.
View 5 Replies
View Related
Mar 21, 2012
We have remote VPN setup with Cisco ASA 5510. By using VPN filter, I can follow the guide and make client to use all necessary server services. (dns, ssh etc). However, is there any way that allow inside server access remote VPN client's services, ex. let inside server ssh to remote VPN client? Consider remote access VPN filter ACL's syntax, I have to always let source be the "remote VPN client PC", the dest is "inside firewall server", how can I let the other way traffice going?
View 1 Replies
View Related
Nov 16, 2011
I am trying to understand how to remote control a clients computer through the internet.
I have Symatec PCanywhere installed on both When i'm on the same connection (wireless internet).I can get it to work no problem.However when I try to remote in using a different internet connection it does not go through.
I've done some research and found out that instead of using the IP address it gives me (dynamically) [192.168.2.5] i need to aquire the WAN IP address from a website or through the router. As well as configuring virtual server through the router, and enable port forwarding in some way or another for specific ports.
View 4 Replies
View Related
Jul 31, 2012
Is there a way to configure RV180 to allow PPTP clients to route Internet traffic via its own internet connection?
I.e. supporting these client options: "Send all traffic" (Mac/iOS), "Use default gateway on remote network" (Windows).
View 1 Replies
View Related
Jan 28, 2013
We are configured the Remote IPSec VPN on cisco 1800 series router.The Clients are able to login to VPN and access the local corporate network Servers . But VPN Clients are not able to communicate with other VPN clients using their VPN Adapter IP.
Components used :
CISCO VPN Client 5.7
Router 1800 Series
View 9 Replies
View Related
May 29, 2013
While trying to connect to WiFi at remote sites APs, the connection is getting time out.User are getting error as 'Unable to connect to <WiFi-SSID>' The APs at corporate office are functioning properly and user are able to connect to the APs.
Wifi Controller: 2504 Software ver: 7.3.101.0
Authentication 802.1x
View 7 Replies
View Related
Mar 18, 2011
i want to invisible my router ip.which command can do this.or how can configure registery to hide my router ip and surf safe.
View 5 Replies
View Related
Feb 6, 2011
I have set up DHCP reservations to assigned IP addresses based on MAC address. I have to block my kids access at times, and when I do this they simply change their IP address and they circumvent the blocking.Other than punishing the kids (which hasn't worked - and they need computers and Internet for homework), is there anyway to lock a computer to MAC address to IP address so if they change it they won't get network/internet access?I also tried to set up network filtering and I put in all the PCs and devices I wanted to provide access for, including the router, but when I save changes I can no longer access the internet or the router. I have to do factory reset to get back into router config.Also, I'm on 1.30WW. I know 1.34 exists, which I tried on a previous router which died and was replaced by RMA; but this didn't solve any problems.
View 6 Replies
View Related
Apr 21, 2011
We are deploying softphones for remote employees in our company. We currently are using Cisco 2921's with VPN enabled.
All of the clients who connect with the Cisco VPN x86 client are getting 00:00:00:00:00:00 for their MAC Addresses, and all of the Cisco VPN x64 bit clients are all getting the same MAC Address, although it is different than the x86 clients.
This is causing the softphones to not work, as they all need to be sending independant MAC addresses.
View 1 Replies
View Related
