Cisco VPN :: 2911 What Command Should Be Entered To Bypass L2tp And Pptp

May 14, 2012

I am working in GULF and skype and other free voice services are blocked. people sometimes use vpn(ivacy) on iphone in the office and it dont work while if they use vpn at there home it works. At office we have only 2911 router and no firewal and simple NAT is done on ADSL interface.what command should be entered to bypass l2tp and pptp.

View 5 Replies


ADVERTISEMENT

How To Prove That L2TP Is More Secure Than PPTP For VPN Using NM

Sep 16, 2011

I have two virtual machines (of Oracle VirtualBox). On one of them,I installed Windows Server 2003 and on the other I installed Windows XP (SP3). I made two VPN connections between them one is PPTP-based and another is L2TP-based. Now I want to transfer a file from the server side to the client side (Windows XP) once using the PPTP-based VPN connection, and again using the L2TP-based VPN connection. And by using the network monitor (protocol analyzer), I have to determine which protocol is more secure than the other.how to know which one is more secure using the network monitor?

View 1 Replies View Related

Cisco WAN :: L2TP Between 7206 And 2911

Oct 1, 2012

i did in past a lot of L2TP connection between two end point. in this case ans with 2911 series with ios 15 and DATA license Activated. the l2tp session does not establishe between a this 2911 and 7209. Attached is topology file and bellow the  configuration of both router.

PE 2911
 
l2tp-class l2-dyn
authentication
password 123456
[Code]....

View 1 Replies View Related

Cisco Infrastructure :: AT Command Set On 2911 PVDM2 Modem?

Oct 8, 2012

I'm having issues trying to dial into the network via ISDN.  Setup is

1.     Users dial in via ISDN PRI/BRI or POTS.

2.     Users using PRI/BRI don't have a problem

3.     Users using the POTS modem way are getting disconnected after approx 5 seconds

4.     Debug shows a disconnect cause '0xF Loss of DTR'

5.     The running config is exactly the same as that of a working 3725 (out of support that's why we're moving to 2911)

6.     Only difference is in the AT Command set modem settings where registry S25 is set to 5 on the 2911 but 0 on the 3725
  
Problem I have is that when I change the registry setting on the PVDM it is accepted, but as soon as I disconnect my reverse telnet session from the line, it reverts back to the default of 5.  How do I save the registry S25 setting so that it won't revert back?       
 
I have changed the settings then carried out a at&w - which made no difference.  I have also carried out the at&y0 after changing the settings but again, made no difference.  I can't find anything on this page Link that shows how to save the settings (but then again, it could be I can't see the wood for the trees).          

View 1 Replies View Related

Cisco Security :: Can Configure A PIX (515) As PPTP Client To Establish A Tunnel With PPTP Server

May 15, 2006

Can I configure a PIX (515), as PPTP client to establish a tunnel with non-Cisco PPTP server ? Can my PIX initiate this type of connection ?Today, I use a PC with PPTP client to establish this and I want replace this with a PIX and I don´t want depends of a PC.

View 5 Replies View Related

D-Link DIR-615 :: MAC Address Entered Is Invalid For Ipad

Jun 3, 2010

I am unable to reserve an IP for my iPad, i.e. add  my ipad to the "DHCP RESERVATIONS LIST".  I get a pop-up saying "The MAC Address entered is invalid."  The address starts with "D8".  My understanding is most start w/ "00".  The router says my firmware is up-to-date (3.01). 

View 11 Replies View Related

Won't Allow Any TCP / IP Connections As IPSec Driver Has Entered Block Mode

Apr 6, 2011

I am having some trouble with one of our servers at work. Basically it won't allow any TCP/IP connections as the IPSec driver has entered Block mode. I have been advised by our external IT support (I can't get hold of him at the moment, that's why I am here ) to go into the command prompt and type: regsvr32 pdstore.dll but when I do this is can't find the file.What is pdstore.dll as when I Google this it comes up with nothing, so is this the correct command?

View 10 Replies View Related

Linksys Wireless Router :: WRT320N Invalid Value Has Been Entered

Dec 20, 2011

I am running a WRT320N with Firmware 1.0.04Trying to Upgrade the Firmware to 1.0.05 it always fails at about 24% progress with a message saying an invalid value has been entered.I downloaded the firmware from your homepage twice so that the file is not corrupted

View 4 Replies View Related

Linksys Cable / DSL :: Wag320n Password Entered Is Not Correct

Sep 5, 2011

I have set up a Linksys WAG320N and while my Dell connects wirelessly my wifes Mac and my iPad do not. When we enter the password the response is that it is not correct.

View 1 Replies View Related

TP-Link 3G/3.75G Router :: TL-MR3220 - Failed To Connect Manually Entered APN

Nov 9, 2012

Region : Hongkong
Model : TL-MR3220
Hardware Version : V1
Firmware Version : 3.14.2 Build 120822 Rel.57775n
ISP : 123

In order to use public IP provided by the ISP, I have to enter the specific APN.It's however no matter what I type in the field of the APN, the router is still connected to the default APN settings from ISP.I have tried typed wrong string in the field of APN, the router is still connected to the default APN successfully.

View 6 Replies View Related

Linksys Cable / DSL :: WAG200G Cannot Connect To Router No Matter What Password Entered

Nov 29, 2009

I have a Linksys WAG200G DSL wireless router and I recently got Network MAgic. When I am trying to connect to change the wireless settings, it always gives me the message that it cannot connect to the router no matter what password I enter! I even used really simple ones such as admin admin and It WONT connect. It gives me the message "Could Not Access Routers Settings". I have the ESET Smart Security AV & Firewall and I have properly configured them to allow communication of Network Magic. I should note that I CAN connect to the router through a browser.

View 4 Replies View Related

Cisco WAN :: 2911/K9 And 2911-Sec/K9 - BOM For Upgrade?

Dec 25, 2011

I am having one router CISCO2911/K9 (Cisco 2911 w/3 GE,4 EHWIC,2 DSP,1 SM,256MB CF,512MB DRAM,IPB). But now my management asking me to upgrade this router as CISCO2911-SEC/K9.
 
What will be the BOM for this up gradation.

View 2 Replies View Related

Cisco VPN :: Use Proxy Bypass On ASA 5510?

Oct 25, 2012

We have a custom web application which is heavily relying on javascript. We're trying to access it via the webportal but this application does not load correctly (it barely shows a white page).
 
the link is [URL] and SUBIF-ISP2 is the public interface facing the internet. This is the rule as displayed by the CLI:
 
proxy-bypass interface SUBIF-ISP2 path-mask oursubdirectory target [URL]
 
Despite having this command in place, nothing changes. I tried multiple combinations adding the xml and hostname rewrite or changing the interface but nothing, the page is the same like if this rule was not applied.

View 4 Replies View Related

How To Bypass 8e6 R3000 Enterprise

Apr 28, 2011

I have tried everything including removing the system, changing the network settings, using cmd.exe, ect. they all say access denied and theres no possible way to get around this.

View 2 Replies View Related

Bypass The Proxy Of School?

Jan 18, 2012

How can I bypass the proxy of my school? I cannot access my emails since I am in the UK and my email is provided with a server in China, namely 163.com; the email means a lot to me as it is the only way I can keep in touch with my friends from my old school.

View 1 Replies View Related

Cannot Get Past Password / Way To Bypass Security

Aug 3, 2012

Im stuck working on a moderm, its a speed touch 536 (old school) i cannot get past a password.. Im trying to set this bad girl up with a router, setting up routers in my specialty.Im trying to bridge the modern but on the setup page there is a password, i dont know if its factory or what.. ive tried many of common passwords for networking like (admin/admin, Admin/ Admin, Admin/Password) ive tried everything i can think of. so i need a way to bypass the security. Flashing the software maybe?Ive found a software uploader for it, but i cant find the original firmware for the modern.

View 3 Replies View Related

How To Bypass Router When It Has Built In Modem

Jun 28, 2011

How to bypass router to modem when the router has a built in modem? So my wireless router has a modem built into it, or is it the other way around: modem with built in router. I'm not sure...But anyway, because I am having such difficulties with the ps3 online, I have been told by many people to try bypassing the router straight to the modem.

View 2 Replies View Related

Bypass Gateway Speed Limiter?

Apr 5, 2012

In my campus they restricted our download speed to 30kbps by registering our laptop in gateway.example.com. It is so ridiculous to download in such a low speed.Even if pages are not opening.

View 1 Replies View Related

Bypass ISP Internet Restrictions When Using A Router?

Jan 27, 2013

My ISP is RDS (Romanian Data Systems) and if i have there cable connected directly to my laptop, i have download speed of 11 MB/s, but if i connect through a router my download speed is just 10% of that. I made a trace and saw that it took 11 points to reach google.com (when i'm connected directly) and 12 when i go through the router. They most certanly cut the band when the ping/trace has a difference of 1 point. They probably do this to preserve the band limits. How can i connect through a router and make the system think i'm connected directly ? So that i can have the same band that i pay for, not just 10% of it?My router is : TP-LINK 300M Wireless N Router Model No. TL-WR941ND . Now i know that in order to make this bypass i can install the Linux version of the router, but i don't know the steps in order to do that.

View 3 Replies View Related

Cisco Security :: Mac Address Bypass Not Working On 3560G

Jul 18, 2012

I'm trying to configure MAB on a Cisco 3560G to work with FreeRADIUS.
  
I have been assured that my RADIUS configuration is fine and the server is functioning properly.
 
This is my current switch config:
 
Header 1 
!
version 12.2
no service pad

[Code].....

View 2 Replies View Related

Cisco Routers :: RV082 Bypass Filter For One User?

Aug 1, 2011

I have been asked by a client to restrict access to a number of non work related sites. Easy, blocked them using Firewall> Content Filter. Then I was asked to disable this filter for one user (the Managing Director) so he can access eBay.
 
I am familiar with doing this on a Netgear device, but so far my efforts with the RV082 have failed.
 
First I have tried using DHCP to reserve an IP address for this user, then setting 'Access Rules' so that this IP has all access all the time, but this does not appear to work.
 
I assume setting this IP as the DMZ would achieve what I want but it seems like overkill and not very security wise.

View 2 Replies View Related

Cisco :: AIR-CAP3502E-A-K9 - How To Bypass Light Weight APs From LMS 3.2 Discovery

Nov 3, 2011

I have been installing Light Weight AP's and these make LMS device discovery take much longer because they are found via CDP but do not run SNMP. So you suffer the SNMP retry and wait time for each one which adds up with several hundred AP's. I added the CDP platform description they announce via CDP to system-config.xml but this didn't do the trick. I have updated system-config.xml successfully in the past to add ATA's and 7936 conference phones and this stopped discovery from processing these devices. So I was surprised when this didn't work for LW AP's. The CDP platform of the AP's looks like this (from show cdp n):
 
Platform: cisco AIR-CAP3502E-A-K9   ,  Capabilities: Trans-Bridge
 
So you can see cisco is all lower case and there appears to be spaces at the end before the comma. I thought the spaces might be the problem so I added them in system-config.xml but this didn't work. When I display system-config.xml with the XML editor in IE it does not show spaces at the end even though they are their when I look at the file with notepad. When I enable debug for discovery it shows these being added to the bypass table for CDP discovery but it still tries to process them. This is LMS 3.2 on Windows Server 2003. I use the CDP module for discovery.

View 6 Replies View Related

How To Bypass Proxy Detection On Public Network

Mar 4, 2011

I just switched schools and I work for HP's marketing team part time which entitles me to get on some websites blocked by our school's network (sonicwall block).I then tried a proxy on Firefox and it was blocked as the sonicwall detected that I was using a proxy. Why did this happen and is there a way to bypass?This is mainly on wired connection as the Ethernet isn't god awfully slow like wireless is.

View 1 Replies View Related

Security / Firewalls :: How To Bypass Internet Restrictions

Dec 7, 2012

we are provided wifi connections. But most of the sites are blocked by cyberoam. way to bypass this (NOTE)ultrasurf and freegate too failed...

View 2 Replies View Related

Work Proxy Bypass On Home Network?

Aug 23, 2012

When I'm at work, I have internet (though a proxy) and remote access to the linux computers at work (the work laptop runs win 7)when I have to work at home, the work VPN that we were given has no internet access but I can connect to the remote linux computer that I need just fine. the linux computer has no internet access and more often than not is missing modules and dependencies. Is there a way to enable my home wifi network and the VPN so that the work computer can access the internet locally while I'm working? just one browser is all I need.... I currently have to disable the vpn, download my modules and then connect, to install them.

View 5 Replies View Related

Bypass The Gateway Laptop Internet Switch?

Aug 23, 2012

On my Gateway laptop there was a switch on the left side. It turned the internet access on or off. The switch broke off, and now I cannot access my wireless internet, I have to be corded.Can I turn off the switch within the computer so I can access my wi-fi?

View 1 Replies View Related

Cisco :: Full Access To Everything Since The Tunnel Is Set To Bypass Interface ACLS?

Nov 23, 2011

I have ip phones at the remote location that connect into the phone switch(it's a nortel cs1000 system) over the tunnel. Internal calls work just fine, however when somebody calls from the outside, or calls are made to the outside the connection is never finalized. Like if I call from my cell it rings the phones, but when I answer there is nothing but dead air.In the group policy for the tunnel, I gave the remote site FULL access to the phones vlan and vice versa...which obviously works since internal calls work fine. If I remove my group policy and give it the Default group policy which essentially gives that tunnel full access to everything since the tunnel is set to bypass interface ACLS, external calls work fine. So it's definitely related to the group policy.

The group policy is basicallyAllow remote site to X network/host on these ports no denies since it blocks whatever isn't specifically allowed. However since it can get the phone switch and it can get to the internet I'm not seeing why the calls aren't working.The only thing I can think of to try doing as well is remove the allow inbound traffic to bypass interface rules and treat it just like another vlan interface on the ASA. Create the rules on each interface for the remote site network etc and see if it works that way.

View 5 Replies View Related

Cisco Switching/Routing :: 3750G - How To Bypass Old Configuration In Switch

Mar 7, 2013

I am having an issue bypassing a switch 3750G series. How i can bypass the old configuration in the switch.i have tried the CTRL+BREAK at startup but it wont work.      

View 2 Replies View Related

Cisco Firewall :: ASA 5540 And Concurrent Sessions - Bypass TCP Connection For One IP

Nov 15, 2012

in Cisco ASA 5540 Adaptive Security Appliance Platform Capabilities and Capacities, I see Concurrent Sessions: 400,000. Which mean what device can handle 400,000 session and no more. But if I'm using TCP State Bypass Feature (Inbound traffic pass via ASA but Outbound goes via different device). I can see such connections via show conn command with b flag.
 
My questions: 1. Will this limit (Concurrent Session) affect in this case? Or ASA can handle more such connections (for example 800,000 ...) in bypass state? 2. It's possible to tune timeout for such connection without using global timeout conn? My problem what I want to do by pass tcp connection for one IP with has very high connection/sec rate.

View 2 Replies View Related

Servers :: How To Get URL To Bypass Boarding School Internet Filter

Mar 22, 2012

I am living on a boarding school and they have a filter set up so we cannot surf for porn and stuff... but the thing is that all other things are blocked and they want an url number make my school better for everyoneIts from a private server Molten WoW so i need them to unlock the Server oO

View 5 Replies View Related

Security / Firewalls :: Block Software With Password Bypass?

Sep 2, 2011

I am currently running a Windows 2003 Server Edition and I have an issue, we run a small piece of software for controlling the nights takings which connects to the tills database on the network.This piece of software is not password protected and is held in a safe, however it has come to our attention that an employee may have taken possession of a copy of this application and we need to block the application been run on the network.Now this is were it gets difficult, I know to stop the application I could just use the Software Restriction Policy with Hash Rules which would solve that. However the problem is that sometimes people WILL need to run this software on the network and not get blocked.These people may not have their own accounts etc so I am trying to workout a way that we can allow someone to bypass the software restriction policy with a password prompt, is this possible or is their another way around this issue?

View 1 Replies View Related

Bypass Proxy / Webwasher With Remote Desktop Connection?

May 11, 2012

I want to connect via windows rdp to computer outside the company office and I cannot do that since we have webwasher or proxy installed in the office.I can access this machine with IE (it is a server with open port 80) and I see its website. This is becuase the IE at office has proxy configured correctly.I cannot access the same machine with RDP connection, though. I can access it using other computer outsite the office, so it is not an issue that rdp is not enabled or so. Problem is with proxy at office.I need a way to connect to rdp by using the same proxy.Problem is that that IE at office uses automated proxy script (.pac).I have installed remote utilities server on the machine I want to access and the remote utilities viewer on the computer at office. I set the proxy similary to what is set in IE but I cannot connect anyway. I can connect this way from third computer outside the office though, so the configuration is fine, only proxy is the problem.I managed to get the proxy details like host name and port but I'm not sure those are the right one.The webwasher or proxy is mcafee web gateway 6.8.4.

View 1 Replies View Related

Check Off Bypass Proxy Server For Local Address Box?

Dec 30, 2011

Charter tech came today to solve my problem of my new modem not working, he fixed the Modem but i think he did something to the lan proxy settings after.I'm trying to set up my Belkin wireless G router but i do not have the orginal CD. What should my address be under the "Use a Proxy server for your LAN" checkbox and what is the port and should i check off the bypass proxy server for local address box?

View 4 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved