Cisco VPN :: 50226 ASA ESP Packet Discard Messages
Dec 8, 2012
we have a L2L tunnel between ASA 8.2.5 to Cisco Router. Recently we see tunnel is going down and shows messages in ASA about ESP packet discard. Below is the message.%ASA-7-710006: ESP request discarded from x.x.x.x to outside_int:x.x.x.At the same time from router the tunnel shows up but ASA not. We see CSCso 50226 which matches exactly with our issue.As a workaround we were resetting tunnel from router. It comes up and runs for a week.
View 9 Replies
ADVERTISEMENT
Feb 23, 2011
We are facing issue of continous packet discards On nexus4001L link (int po2) to Nexus5020 switch. Nexus4001L is installed in IBM blade center server and we have FCOE enabled in this setup. [code]
View 2 Replies
View Related
Nov 27, 2011
Using a Samsung Galaxy S2, iPod Touch 3rd Gen, and Nook Color, they are all experiencing retry problems, even when 3 feet from the DIR-601. When I use them my log gets filled with messages like:Blocked incoming TCP Ack packet from 192.168.100.201:2926 to 209.85.145.113:80 with unexpected sequence On the devices I see the downloads/content taking a long time to appear and often I get a blank page or "Retry" messages. I purchased two DIR-601s and get the same problem with both. They are both running 1.02NA firmware. The WLAN is Time Warner cable modem. Prior to this I had a Linksys WRT-54 that gave great performance, though just at B/G speeds. I was hoping for a performance boost but right now the N speeds are slower than B with the retries.
View 5 Replies
View Related
Jan 19, 2012
we have a core switch 4507RE at the data center and 2 departments that connect to it via 10Gig fiber using X2-LRM modules. Each department has a 3 switch stack and both locations are identical w.r.t type and setup scenario.the stack comprises of 1 x 3750E and 2 x 3750G . uplink is from X2 port tengig3/0/1 from the 3750E switch.
All of a sudden dept B started facing problem , where the ping would break and throughput comes around 6 - 7 mbps from that dept to the server behind the core switch. we also noted CRC error on both sides preodically.
we replaced the multimode fiber patch cords, re did the splicing , which stopped the CRC errors to appear.now since morning the uplink port on the 3750E (3/0/1) would suddenly be in "down" state with (err-disabled) as the status when i run sh int ten 3/0/1
and i can also see CRC errors and input errors on the same interface.. if i do shut / no shut .. the port is up and active again.. but this has happned 3 times today.the core swith side is still OK and no CRC / input / output errors are seen..
now on the 3750E i have swapped the 10gig module from 3/0/1 to 3/0/2 . the port is still up but i can see 400 CRC and 500 Input errrors.the module is also OK as i had replaced it with dept 1's module.
View 1 Replies
View Related
Apr 4, 2011
We're seeing "OutDiscard" error on a LAN switch connected to newly migrated Cisco IP phones. All the other error counters are clean except for the OutDiscard. (please see attached "show int count err" output.) [URL].
According to the link above, the common cause of such discards can be to free up buffer space.(Am I seeing a switch buffer issue?) How to identify/resolve the cause of the OutDiscard.The switch is 3750-E running c3750e-universalk9-mz.122-44.SE6.bin
View 1 Replies
View Related
Nov 17, 2011
I have 2 NX4001. Each one has an uplink to a 5K. There is no VPC between the 4K and the 5K. The 5K are VPC enabled.There is a large number on input discards on the 4001 interfaces connected to the 5K and is incrementing.I have a server with smartfailover that is flapping and I think the input discard might be the culprit.what is the cause on input discard. Note: All NXOS to the latest.
View 2 Replies
View Related
May 21, 2013
I faced the ( receive discard vlan 20 of Cisco switch 3560 ) on my Solarwinds Server .
View 1 Replies
View Related
Dec 6, 2012
reasons for increasing "Output Discard” Interface Counter in Nexus2000 . ????
View 2 Replies
View Related
Apr 15, 2010
I have two 3560G 24 port switches. Each of them connects to some 3560G or 2950 switches. Trunks between 3560G are set as 1000/full. Trunks between 3560G and 2950 are set as 100/full. show int status also shows the interface negotiation is 100/full for trunks between 3560G and 2950. The issue is I keep getting outdiscard errors in trunks between 3560G and 2950. At 2950 switches, I see Recv-errors too. I checked all the trunks traffic. They are totally not high. Only serveal mbps. Most time even lower than 1mbps.
I googled this kind of issue online. I see it could be possibly caused by high volume traffic higher than the capacity. But it appears the traffic there is not high enough to cause this kind of issue. Is there any possiblity that could cause this problem?
The below is 3560G trunk configuration for 2950 switch
interface GigabitEthernet0/10 switchport trunk encapsulation dot1q switchport trunk allowed vlan 1-122,124-4094 switchport mode trunk speed 100 duplex full srr-queue bandwidth share 10 10 60 20 queue-set 2 priority-queue out mls qos trust cos auto qos voip trust
the trunk configuration at 2950 switch: interface FastEthernet0/24 switchport trunk allowed vlan 1-122,124-4094 speed 100 duplex full
View 16 Replies
View Related
Feb 13, 2012
As always, the Cisco LMS is keep sending the follwoing high discard error from the Cisco switches WS-C2950T-24:
EVENT ID = 0004SX3
ALERT ID = 00019LF
TIME = Tue 14-Feb-2012 08:56:35 GMT
[Code].....
View 4 Replies
View Related
Oct 3, 2012
I have noticed poe log messages in my cisco 857 router, looking around there is mention of a cosmetic ios bug pertaining to 877 router but not the 857. BUG - CSCsd68389. Why i am getting these errors on my 857?
001586: Oct 5 11:25:06.499 NZST: esw_dtc_ltc4258_reg_write: no acknowlege from POE
001587: Oct 5 11:25:06.499 NZST: esw_mrvl_pdc_hardware_config failed on slot 0/0
001601: Oct 5 13:06:29.879 NZST: esw_dtc_ltc4258_reg_write: no acknowlege from POE
001602: Oct 5 13:06:29.879 NZST: esw_mrvl_pdc_hardware_config failed on slot 0/0
001603: Oct 5 13:06:31.387 NZST: esw_dtc_ltc4258_reg_write: no acknowlege from POE
001604: Oct 5 13:06:31.387 NZST: esw_mrvl_pdc_hardware_config failed on slot 0/0
[code].....
View 3 Replies
View Related
Feb 11, 2013
i have been facing this problem as i cannot see any log messages via my console port,except by looking at logs manually by "show log" command,
View 3 Replies
View Related
Dec 6, 2012
we're trying to integrate our SBC instances (CUBE SP on ASR1000) into our network management system (EMC SMARTS)Syslog messages from SBC instances are some kind of cumbersome with lot of line breaks resulting in multiple syslog messages the NMS must parse.How do I configure it to just put it all into one line just as "normal" log messages?
View 2 Replies
View Related
Mar 12, 2012
I have a new install of LMS 4.2 on a virtual appliance. No syslog messages are getting into LMS. They are being received by the server, but are showing up in /var/adm/CSCOpx/log/dmgtd.log, and aren't getting processed by SyslogAnalyser.
View 3 Replies
View Related
Sep 28, 2011
LMS 4.1 is not showing any valid syslog messages, only invalid messages. Is there anything different in 4.1 that needs to be set?
View 2 Replies
View Related
Jun 19, 2012
My Cisco devices send syslog messages to LMS but it wont`t show any messages from device. Older LMS 3.2 and other collector showe all syslog messages. What to do with LMS 4.0.1?
View 2 Replies
View Related
Mar 3, 2013
I have a newly installed LMS 4.1 that had the Syslog feature working for a while.
Recently, the Syslog is no longer displaying any records (neither new or old messages).
Below are the steps I have tried to troubleshoot the problem:
- Installed wireshark : Syslog messages are being received by the LMS server on time
- In the Syslog.log file, I can see that all the Syslog messages are being logged properly
- I tried to disable all the "Syslog Message Filters" but nothing changed
In the SyslogCollector.log, I can find the below logs:
NMSROOT is C:/PROGRA~2/CSCOpx
propFileC:/PROGRA~2/CSCOpxMDC omcatwebapps
meWEB-INFclassesC:PROGRA~2CSCOpxMDC omcatwebapps
[Code]....
View 0 Replies
View Related
Aug 22, 2011
I have a small problem with a lot of invalid syslog messages in LMS 3.2. Something about 30% of all messages are invalid.
Is there any posibility to get out from which devices those messages are?
Is it a big problem for the application if there are such a lot of invalid messages? I have a lot of devices in my LMS and don't want to get high load because of such unneeded messages.
View 1 Replies
View Related
Dec 21, 2011
We need IPM (LMS 4.1) to send and e-mail, sms o trap to NNM, is it possible??
View 2 Replies
View Related
Feb 7, 2013
what can i do if my computer is not letting me see my messages on facebook what
View 1 Replies
View Related
Mar 30, 2011
it keeps repeating 2 messages then timing out
View 1 Replies
View Related
Jul 26, 2012
I'm getting the Syslog messages frequently on daily basis.
View 4 Replies
View Related
Jun 26, 2012
Is there a way to debug syslog messages? Something like "debug ip syslog"?
View 11 Replies
View Related
Apr 25, 2013
I have a Cisco ASA 5505 I've configured as a DHCP server. I'm getting DHCP on workstations attached to the appliance, but I'm getting the following message when the appliance loads:DHCP Client: can't enable DHCP Client when DHCP Server/Relay is running on the interface DHCP: Interface 'inside' is currently configured as SERVER and cannot be changed to a CLIENT by a CLIENT featureI'm not trying to configure this thing as a client, so I'm not sure why the system is producing this message.
View 2 Replies
View Related
Jul 27, 2011
After installing a S370, and upgrading AsyncOS, I have critical messages such as:
An application fault occurred: ('journal/base.py _check_file_size|371', "<class 'journal.exceptions.CorruptError'>", 'CorruptError: File size does not match (33328990208 38708391936)', '[coeuslog/coeuslogd.py run|909] [coeuslog/coeuslogd.py _run|872] [journal/base.py mount|437] [journal/base.py _mount|493] [journal/base.py _recovery|577] [journal/base.py _check_file_size|371]')
Product: Iron Port S370 Web Security Appliance
Model: S370
Version: 7.1.0-307
Serial Number: 842B2B49C468-CNLVX4J
Timestamps: 27 Jul 2011 12:16:03 +0200
View 2 Replies
View Related
Mar 17, 2010
provide input on what these Traceback messages are and how they are caused:
*Mar 15 23:07:57.250: %SERVICE_MODULE-4-WICNOTREADY: Unit Serial0/1/0 not ready for next command -Traceback= 0x41173B5C 0x40371894 0x40371928 0x40371CE0 0x40372794 0x40369AF0 0x40382908 0x4037FEB4 0x4037FF80 0x41EF56B4 0x41EF95E4 0x41EEA51C 0x41F12B00 0x42183F44 0x42183F28*Mar 15 23:08:00.250: %SERVICE_MODULE-4-WICNOTREADY: Unit Serial0/1/0 not ready for next command -Traceback= 0x41173B5C 0x40371894 0x40371928 0x40371CE0 0x40372794 0x40369AF0 0x40382908 0x4037FEB4 0x4037FF80 0x41EF56B4 0x41EF95E4 0x41EEA51C 0x41F12B00 0x42183F44 0x42183F28*Mar 15 23:08:03.250: %SERVICE_MODULE-4-WICNOTREADY: Unit Serial0/1/0 not ready for next command -Traceback= 0x41173B5C 0x40371894 0x40371928 0x40371CE0 0x40372794 0x40369AF0 0x40382908 0x4037FEB4 0x4037FF80 0x41EF56B4 0x41EF95E4 0x41EEA51C 0x41F12B00 0x42183F44 0x42183F28.... and so on.
We recieved this for one of our routers. Rebooting it worked, so it's likely a software bug and we will upgrade the IOS soon, but I would like to understand what these log messages.
View 5 Replies
View Related
Nov 27, 2012
I am constantly getting a few errors in my ASA 5510 and 5505 from the same IP. The IP of my NMS server, which has also stopped recieving SNMP data from these two VPNs.
Syslog Id: 713048 Error process payload: Payload ID: 1
Syslog ID: 713902 Removing peer from peer table failed. No Match.
Syslog ID: 713903 Error: Unable to remove PeertblEntry
I have tried to configure ACL to let traffic through. SNMP traffic to be more precise, but since I am fairly new to cisco firewalls and SNMP in general this has proven very difficult.
View 8 Replies
View Related
May 26, 2013
My customer is seeing these Errors coming up on one of his 2504 WLC's (ver7.3) The MAC's and IP addresses Mentioned seem to be completely fictitious as the customers IP plan is way off these subnets and the vendor lookup tool cant resolve the MAC addresses.I can confirm that there is no conflict.I've seen them appear on other 2504's across his network on seperate occasions.
View 4 Replies
View Related
Apr 10, 2013
How can I filter outbound sys log messages, so they include only configuration changes messages..
On Cisco 2900 I used:
logging discriminator CFG LOG msg- body includes "PARSER" | "CONFIG"
logging host x.x.x.x discriminator CFG LOG
logging x.x.x.x
How can I do the same on 4507? This feature on Cisco routers is called "Reliable Delivery and Filtering for Sys log" and is available for 12.4(11)T and 12.2(33)SRB (7600) . I am running Version 12.2(25)EWA6 on my Catalyst, so it is not available.
The software I am using is a simple solar winds sys log server.
View 2 Replies
View Related
Jul 16, 2011
I think I got a strange behavior on a context of my WS-SVC-FWM-1 (on a Catalyst 6509 running IOS 12.2(18)SXF17a) that is running FWSM Firewall Version 4.1(3). This context sends these log messages every ten minutes:
Jul 17 2011 23:31:16: %FWSM-6-302010: 0 in use, 0 most used
Jul 17 2011 23:31:17: %FWSM-6-302010: 2245 in use, 107133 most used
[code]...
If I issue the "show conn" three seconds later the log message, the output I got is: FWSM# sh conn 1041 in use, 107133 most used
In another context on the same FWSM the log message sent every ten minutes is just this one:
Jul 17 2011 23:31:17: %FWSM-6-302010: 1358 in use, 72503 most used
Jul 17 2011 23:41:22: %FWSM-6-302010: 1590 in use, 72503 most used
In this case there is no the log message where the "in use" field and "most used" field are 0 (zero). why does the context send the message with the "in use" field and "most used" field 0 (zero).
View 1 Replies
View Related
Jun 9, 2011
How do I find deleted hotmail messages from a few years ago that I sent out off of my computer?
View 1 Replies
View Related
Jan 20, 2011
Our building used to have a very old server that basically just served as a place for teachers to store files and not much else. We have just changed ISPs and decided that we no longer needed the server at all. I disconnected the server from the network and replaced the old ISP's modem with the new ISP's modem. At first, everything seemed OK. My computer and several other teachers' connected to the Internet with no problem. However, some of the computers in the building could not connect. We get error messages with "limited or no connectivity." Part of me thought that perhaps the connections themselves are bad. However, when I take my laptop to classrooms with trouble connecting - mine connects easily using their cables. If I move their computers to my room, their laptops still won't connect. I have put my computer side-by-side with another one to make sure the settings were the same (auto-detect IP, DNS, etc.) and can't find differences. This problems is affecting our Windows 7, Vista, and XP computers the same.
View 11 Replies
View Related
Aug 17, 2011
I recently got multiple messages from Avast Virus giving me this message.Object: Infection URL:Mal, Process: CWINDOWSsystem32svhost.exe I have run Malewarebytes and a full boot scan with Avast and and I have not been able to get the message to stop showing up. how to stop this?
View 2 Replies
View Related
