Cisco VPN :: ASA 5505 Site-to-site VPN Tunnel And Client VPN Sessions?

Nov 14, 2012

i have a client who needs to establish a VPN tunnel from his satellite office (Site A) to his corporate office (Site Z).  His satellite office will have a single PC sitting behind the ASA.  In addition, he needs to be able to VPN from his home (Site H) to Site A to access his PC.The first question I have is about the ASA 5505 and the various licensing options.  I want to ensure that an ASA5505-BUN-K9 will be able to establish the site-to-site tunnel as well as allow him to use either the IPsec or SSL VPN client to connect from Site H to Site A.  Secondly, I would like to verify that no special routing or configuration would need to take place in order to allow traffic not destined for Site Z (i.e., general web browsing or other traffic to any resource that is not part of the Site Z network) to go out his outside interface without specifically traversing the VPN tunnel (split tunneling?)Finally, if the client were to establish a VPN session from Site H to Site A, would that allow for him to connect directly into resources at Site Z without any special firewall security rules?  Since the VPN session would come in on the outside interface, and the tunnel back to Site Z goes out on the same interface, would this constitute a split horizon scenario that would call for a more complex config, or will the ASA handle that automatically without issue?

View 1 Replies


ADVERTISEMENT

Cisco VPN :: ASA 5505 / Site To Site Vpn With One Site Always Initiate A Tunnel?

Feb 7, 2011

I have ASA 5505, i configured site to site vpn between central site and remote site and is working. Now the problem is we use remote site for troubleshooting purpose, so we need to create a tunnel from remote site to central site. I need to configure such a way that remote site can craete a tunnel to central site, but central site not able to create a tunnel, it just respond to remote site.

View 3 Replies View Related

Cisco VPN :: How To Setup VPN Client And Site-to-site Tunnel On 831

Feb 8, 2011

How can I set up a Cisco 831 router (branch location) so that it will accept inbound VPN Client connections and initiate a site-to-site IPSec tunnel to our hub location that uses a VPN 3005 Concentrator?  I could get the tunnel to work by configuring it in a dynamic crypto map but interesting traffic on the Cisco 831 side would not bring the tunnel up. 

View 5 Replies View Related

Cisco AAA/Identity/Nac :: ASA 5505 - Procedure For Monitoring Site-to-site VPN Tunnel?

Apr 30, 2012

Need to know the step by step procedure for monitoring site-to-site VPN tunnel (up/down) using SNMP on Cisco ASA 5505. 

View 1 Replies View Related

Cisco VPN :: Site To Site VPN IPSEC Tunnel From ASA 5505 To Clavister Firewall

Nov 20, 2012

I have weird problem with a Site to site VPN tunnel from a Cisco ASA 5505 to an Clavister Firewall.When I restart the Cisco ASA 5505 the tunnel is up and down,up, down, down, and I get all strange messages when I see if the tunnel is up or down with the syntax: [code]
 
After a while like 5-10 min the vpn site to site tunnel is up and here is the strange thing happening I have all accesslists and tunnel accesslists right I can only access one remote network (Main site Clavister Firewall) trought the vpn tunnel behind the Cisco ASA 5505, and I have 5 more remote networks that I want to access but only one remote network is working trought the vpn tunnel behind the Cisco ASA. I see that when I do this syntax in ASA: show crypto ipsec sa.They had a Clavister Firewall before on that site before and now they have a Cisco ASA 5505 and all the rules on the main site thats have the big Clavister Firewall is intact so the problems are in the Cisco ASA 5505. [code]
 
All these remote networks are at the Main Site Clavister Firewall.

View 1 Replies View Related

Cisco VPN :: ASA 5505 - Users Aren't Able To Reach Remote Network Through Site-to-site Tunnel

May 21, 2011

Remote-access users aren't able to reach our remote network through a site-to-site VPN tunnel between two ASA 5505's.
 
I've seen several threads about that here, I've run through the walkthrough at [URL] I've taken a stab at setting split tunnelling and nat exemption, but it seems I'm still missing something. Remote-access users can reach the main site, but not the remote site.
 
Remote-access (vpn-houston) uses 192.168.69.0/24.
The main site (houston) uses 10.0.0.0/24
The remote site (lugoff) uses 10.0.1.0/24

View 5 Replies View Related

Cisco VPN :: Establish Site-to-site VPN Tunnel Between ASA 5505 And C881?

Dec 27, 2012

Last week, I was able to establish a site-to-site VPN tunnel between an ASA 5505 and Cisco C881 router just fine. The tunnel was up and and running for a number of days but today the tunnel is no longer up.  I was wondering how, if there are any commands  to re-establish or re-initiate the tunnel.

View 3 Replies View Related

Cisco Firewall :: ASA 5505 Setup A Site To Site Tunnel?

Nov 13, 2012

I have a 5505 asa code version 8.3(2). Trying to set up a site to site tunnel with someone and he is asking if I can use ike v2. How do I go about setting up the tunnel to use ikev2? Is ikev2 an option with site to site tunnels?

View 5 Replies View Related

Cisco VPN :: ASA 5505 / Static Routes Through Site-to-site Tunnel

Dec 17, 2012

I am using a Cisco ASA 5505 Here is a description of my topology.
 
Headquarters = 192.168.201.0
Client X = 172.16.0.0
Datacenter = 10.12.0.0
 Site to Site Tunnels:
Headquarters ---> Datacenter
Datacenter ---> Client X
 
I want to ability for computers in the Headquarters subnet to access the Client X subnet.I have tried setting up a static route to push all traffic destin for 172.16.0.0 to the datacenter, but was unsuccessful. how I can route all 172.16.0.0 through the tunnel.I have tried ading a static route on my ASA but without success.

View 3 Replies View Related

Cisco VPN :: ASA 5505 Site-to-Site VPN Tunnel Up But Not Passing Traffic

Apr 3, 2013

I do have a 5505 up and running, and passing data... url...Now I am trying to get a IPSEC VPN tunnel working.I actually have it up (IKE phase 1 & 2 both passed), but it is not sending/receiving data through the tunnel.
 
The networks concerned: name 10.0.0.0  Eventual  (HQ Site behind Firewall)name 1.1.1.0  CFS  (Public Network Gateway for Palo Alto Firewall - Firewall IP: 1.1.1.1)name 2.2.2.0  T1  (Remote site - Outside interface of 5505: 2.2.2.2)name 10.209.0.0  Local  (Remote Network - internal interface of 5505: 10.20 9. 0.3)  On a ping to the HQ network from behind the ASA, I get port map translation creation failed for icmp src inside:10.209.0.9 dst inside:10.0.0.33 (type 8, code 0)
 
I am suspecting that there is a NAT error and/or a lack of a static route for the rest of the 10.0.0.0 traffic, and that I may have to exempt/route the traffic for the HQ network (10.0.0.0), but I haven't been able to get the correct entries to make it work. [code]

View 22 Replies View Related

Cisco VPN :: ASA 5505 - Twice NAT Across Site To Site Tunnel With Same Private Networks

Mar 30, 2013

I'm currently trying to configure a Site to Site tunnel between an IOS Router and an ASA 5505 running 9.1
 
When the private subnet of the IOS Router was 10.0.0.0/24 and the private subnet of the ASA was 172.16.1.0/24, it connected fine.
 
I'm now trying to set it up where both private networks are 10.0.0.0/24, and created network objects, edited the ACL for interesting traffic, and created the twice NAT translation rule, but the tunnels aren't coming up.
 
There is the IOS Router(R1) and the ASA(F2). In between them is one Internet posing router that is just set up to allow both sides to reach their WAN addresses.
 
R1 and F2 have private network (10.0.0.0/24) and need to communicate. Twice NAT can be done all on the ASA to allow this, but I must be doing something wrong. The way I understand it, is that the R1 should see the traffic coming from 10.51.0.0/24 and sending to that traffic. The ASA will take that traffic, and the inside network should see it come inbound as 10.50.0.0/24. So the F2 private network communicates with 10.50.0.0/24 and R1 private network sends traffic to 10.51.0.0/24.
 
I turned on "Debug crypto ipsec" and "debug crypto isakmp" but no output is showing up or giving any hint that it is trying to establish anything. 
 
R1#show run 
version 12.4
hostname R1
crypto isakmp policy 50encr 3desauthentication pre-sharegroup 2crypto isakmp key cisco address 10.2.0.254

[Code]......

View 3 Replies View Related

Cisco VPN :: 5520 And 5505 Site-To-Site Tunnel Between Two ASA

Apr 2, 2013

I am using the Site to Site Wizard on an ASA 5520 and ASA 5505 from the ADSM. Both are using 8.4(5). When you create the configurations. Do you have to follow up the wizard configurations with manual ACL's to allow for traffic from each connected subnet to talk to each other? Or are they automatically generated in the configuration file? Have not been to school yet to properly understand how to create the VPN tunnels from the CLI and what to look for.

View 2 Replies View Related

Cisco VPN :: ASA 5505 Site-to-site Tunnel Is Disconnected

Dec 6, 2012

I am running site to site VPN from site B to site a.On siteB. I used following DNS in site B DHCP from 5505 ASA.dhcpd dns 192.168.1.1 202.66.192.68..When the site to site tunnel is working.  It is normal DNS requests from site B to site A DNS.  however, if the site to site tunnel is disconnected, site B not able to request site A DNS and do not jump to second DNS 202.66.192.68. I want siteB can use secondary DNS: 202.66.192.68 when tunnel is not connected. 

View 2 Replies View Related

Cisco VPN :: ASA 5505 - Site To Site Tunnel Disconnect

Dec 12, 2012

I am using 5 Cisco 5505 ASA builed site to site VPN. site B,C,D,E all site to site VPN to site A with only IKEv2 IPSEC configurartion.
 
Reading from Site A ASDM.  Monitoring VPN always can read all four site are connected.  But, I found that Site D and E the login time during reset time to time with few hours. 
 
1) I would like to know the login time during reset is normal or not?

2) any setup or configuration can fine tune the site to site VPN.  Make VPN tunnel more stable?

3) any menthod can monitor site to site VPN is health or not?

View 2 Replies View Related

Cisco VPN :: ASA 5505 - Site To Site Tunnel With Same Subnet

Feb 4, 2013

I have ran into this problem in the past but clearly I usually change one of the remote host sub net ranges to something other than main site. Now I am in a situation that I just have to configure it this way. I just need some insight before implementation.
 
Inside (10.10.10.x/24) ASA5505 outside (97.65.x.x) ßà (97.664.x.x) outside ASA5505 (10.10.10.x/24) 
 
Trying to create a site to site tunnel between each location with same sub net. I have found a lot of information about setting up this configuration with 8.3 and later but nothing for the image 8.4 and image 9.1(1) as everyone knows the ACL's and NAT statements are written differently now.

View 5 Replies View Related

Cisco VPN :: 5505 Is Connected Via A Site-to-Site Tunnel

Sep 30, 2012

I've got a Cisco 5520, to which is a Cisco 5505 is connected via a Site to Site tunnel.The tunnel works just dandy, with traffic happily being passed to and from my Inside interface.
 
The issue comes with users connected to the 5505 access our DMZ, it simply refuses to work. I've read many posts about the changes made in 8.3 (which I'm running on the 5520) when it comes to NAT exemptions which I believe is the issue I'm having but I'm not able to implement any configuration to allow my site to site VPNs to connect to hosts within the DMZ.
 
An old copy of the configuration below (I tried many things after this point, but this is one of the cleaner copies!), [code]

View 5 Replies View Related

Cisco VPN :: 5505 Configuring VPN Client To Site-to-site

Jun 3, 2013

We have a Cisco ASA 5505 at our CORP location, which I have configured the Site2Site VPN to our COLO with a Juniper SRX220h, the site to site works fine, but when users access the Cisco VPN client from home, they cant ping or SSH through the Site2Site.  Contacted JTAC and they said its not on their end, so I tried to contact Cisco TAC, no support.  So here I am today, after for the 3 days (including Friday last week) of searching the Internet for over 6hrs a day, and trying different examples of other users. The VPN client show the secured route to 10.1.0.0. [code]

View 19 Replies View Related

Cisco VPN :: ASA 5505 - Site-To-Site VPN Tunnel

Jul 5, 2012

Is there a limit on how many remote networks you can specify on a Site to Site VPN tunnel?

View 1 Replies View Related

Cisco VPN :: To Keep Site To Site Tunnel Always Up - ASA 5505

May 1, 2012

We installed an ASA5505 an we configured a vpn l2l to another asa,unfortunately this vpn tunnel sometimes goes down and do not come up again, in order to keep it up we need to have a continuos ping to generate traffic inside the tunnel.,How is possible to keep this vpn tunnel always up?,This is the config,ASA Version 8.4(1).

View 2 Replies View Related

Cisco VPN :: ASA 5505 Site To Site Tunnel

May 18, 2011

I have a simple question, but want to make sure before I start. I have 3 5505 devices, 1 at corp, and 1 at two site locations. Is it possible to have multiple tunnels on the corp asa? one to site #1 and one to site #2?

My license is Base on all of the ASA's. I already have remote user VPN setup on the devices as well. Will that hurt or hinder anything to add the tunnels?

View 2 Replies View Related

Cisco VPN :: 5505 - Site To Site Connected But Cannot Ping Remote Site

Oct 11, 2011

cisco products and am struggling getting a VPN going between an ASA 5505 and 5510.  I have a VPN created (using the VPN wizward on both) and it shows the VPN is up, but I can't ping the remote site (from either side).

View 11 Replies View Related

Cisco VPN :: ASA 5505 Site To Site Connection / Remote Site?

Mar 6, 2011

i have 2 router asa 5505 with base license i wanna make site to site vpn connection and remote site using vpn client to connect first i have hdsl router with 5 public ip i wanna try it by giving 1 public ip to each router and try the vpn but nothing work?

View 1 Replies View Related

Cisco VPN :: 1800 Site-to-Site VPN Tunnel Bandwidth For Voice Traffic

Jun 22, 2011

I have some challenges with a VPN config I recently setup for a client.I have at the HO the following:

- 1800 router
- Avaya phones and Gateway
- 1MB radio internet access
 
At the BO(branch office), i have:

- 871 Router
- Avaya phones
- 256k internet bandwidth
 
The only reason we setup the VPN in the first place was for the phones at the BO to be able to connect to the gateway at the HO and also able to make calls and receive calls as if the phones were at the HO.The phones at the BO successfully register to the HO, but are unable to recieve calls and dial out. Everytime I try to make a call, the phone displays a "connecting..." message. [code]

View 2 Replies View Related

Cisco Firewall :: ASA 5510 - Allow Only One Host Access To VPN Site To Site Tunnel

May 28, 2012

I have a ASA 5510 that has multiple site to site VPNs. I need to create an additiona site to site VPN but only allow 1 host to access and traverse the tunnel. The network is on a 192.168.5.x but the host that will need to access this tunnel needs to be on a 172.16.33.x network. I dont want any other traffic allowed to access or traverse the VPN tunnel for this host.  How can I set this up?

View 33 Replies View Related

Cisco Routers :: SRP521W VPN Site-to-Site Tunnel Doesn't Establish

Dec 19, 2011

As you can see i have problems with connecting 2 SRP521W together for an VPN tunnel. I tried as much as I can but now i dont know what to do or how and where is the mistake? the connection between these two devices was there last week, after weekend (nothing changed in configs) the connection suddenly was interrupted, without any reason or warning. another day it worked again and 20 mins later connection was dead again...and now it wont establish at all.. here are some screenshots from the vpnconfigs of my devices. one has a static IP the otherone uses FQDN. These are the IKE policies: Here the IPsec Policies: and the GRE policies:

View 10 Replies View Related

Cisco WAN :: 3825 Shared Internet Through Site To Site IPsec VPN Tunnel

Apr 24, 2013

I have configured Ipsec vpn tunnel beetween two routers (from site A to site B) over untrusted internet connection by cisco 3825 routers and i can  successfully access both of this routers. But now i need to access internet on site B router sitting on site A router. So that if i run traceroute from A site machine then the gateway by which internet passing through shows the ip of site B.

The Architecture of our both site routers :

Site A  10.1.11.0-----Router A 172.18.12.1-----VPN tunnel----Router B 172.18.12.2-----Site B 10.4.11.0 

/////Create IKE policy
crypto isakmp policy 1
encr aes
authentication pre-share
group 2
[Code] .....

View 10 Replies View Related

Cisco VPN :: 5510 Hair Pining VPN Clients Through A Site-to-site Tunnel

Apr 30, 2013

I have an ASA 5510 8.2(5) in Site1 and a ASA 5505 8.2(1) Site2 they are setup with a site to site tunnel.Each site has VPN clients that connect and I would like to allow clients from both sides access to servers on the other side of the site-to-site tunnel.
 
I enabled same-security-traffic permit intra-interface I also added the remote networks to access-list that is doing the split tunneling. [code]

View 33 Replies View Related

Cisco VPN :: ASA5520 - Access-list For Site-to-Site IPSEC Tunnel

Dec 1, 2011

How can I NAT the same set of four hosts and give them access to two different networks across an IPSEC site-to-site VPN tunnel?  I'm using an ASA5520 running 8.04.
 
I have four hosts say: 10.240.1.1-10.240.1.4
 
They need access to two different networks:

205.100.150.0
140.175.200.0
 
I woud like to NAT them as something like:

7.5.210.1
7.5.210.2
7.5.210.3
7.5.210.4 

View 1 Replies View Related

Cisco VPN :: 506 Firewall 6.3(4) PDM 1.0 / Broke Remote VPN After Site To Site VPN Tunnel Created?

May 19, 2011

It's been a long time since I played in Cisco CLI.Using a Cisco 506 Firewall 6.3(4) PDM 1.0?Problem is I created a site to site tunnnel with a vendor and since then our remote VPN does not work. Completely times out so I am sure I broke something in the crypto map or something similar.
 
Tunnel is policy 10 using access-list 101
Remote VPN is Policy 20

Config Below:

: Saved:PIX Version 6.3(4)interface ethernet0 10fullinterface ethernet1 10fullnameif ethernet0 outside security0nameif ethernet1 inside security100enable password XLk0qAaMaA6kjvA6 encryptedpasswd VeCrsQbWdIFPwnny encryptedhostname RMS-DR-PIXdomain-name RMS.Localfixup protocol dns maximum-length 512fixup protocol ftp 21fixup protocol h323 h225 1720fixup protocol h323 ras 1718-1719fixup protocol http 80fixup protocol rsh 514fixup protocol rtsp 554fixup protocol sip 5060fixup protocol sip udp 5060fixup protocol skinny 2000fixup protocol smtp 25fixup protocol sqlnet 1521fixup protocol tftp 69namesobject-group network FTP_Clients description FTP Client PCs network-object host 192.168.xxx.xxx network-object host

[code]....

View 4 Replies View Related

Cisco VPN :: Establish Site To Site IPSec Tunnel Between ASA 5520 And 3030?

Feb 17, 2013

We have configured a site to site tunnel from our ASA to another organizations Cisco 3030.  It appears to have just one way initiation.  We can do a ping to a device on the remote site and it will ping just fine.  however, when the tunnel needs to be initiated from the remote site, it will not work until we have initiated the tunnel and then everything works.
 
I continue to see Error processing payload: Payload ID: 1 errors on the ASDM logs.It appears that all the configuration is in place because we can in fact establish the IPSec tunnel unidirectional.  And once established, traffic can flow bidirectional.

View 1 Replies View Related

Cisco VPN :: 2901 / 2951 - Site-to-Site VPN - Constant DPD - Tunnel Drops

Dec 12, 2012

We have approx 40 branch offices - all of which are connected to a single core site over VPN Tunnels using various gear. At one particular site, we are having issues with the tunnel dropping sporadically throughout the day - some days it happens 10 times, some days it happens none. This just randomly started happening two weeks ago, without any changes taking place. Since it started happening, I have upgraded the code to latest versions, but still the issue persists. This particular site has a 2901 and connects back to a 2951.
 
Below is the output from:

debug crypto ipsec
debug crypto isakmp

[code].....

View 1 Replies View Related

Cisco VPN :: 4500 Switch - Dot1q Tunneling Via PPTP IPSec VPN Site-to-site Tunnel?

Nov 28, 2012

I have a situation where the site-to-site tunnel is already established using PPTP IPSec VPN with non Cisco Gateways terminating the link on each end. These non Cisco Gateways do not support L2TP tunneling, and there is no plan to change them.Beyond the Gateways on both ends, we have a Cisco 4500 series switch. We need to forward the 802.1q tagged VLANs between the two sites. Is it possible to use 802.1Q tunneling in this case, going via a PPTP tunnel ?
 
Cisco's setup uses dot1q-tunnel over a L2protocol-tunnel to preserve the original client VLAN tagging, so does this mean that the only option we have is to setup a L2TP tunnel at the Cisco device endpoints, and have that tunnel go through the existing PPTP tunnel (established between the 2 non Cisco VPN Gateways) ?

View 1 Replies View Related

Cisco Wireless :: Configuring 5508 At Remote Site To Tunnel Traffic From WLC At Main Site?

Sep 20, 2012

At the main site, I have 3 5508 WLCs each part of a mobility group (wlcMain-MG).  In NCS, under "System/Mobility Groups" for each controller, I see each controller listed as "local" with the other Controllers listed with the group name "wlcMain-MG".  None of the SSIDs are "anchored".
 
I have a new site with a 2500 series WLC that I would like to push out 2 SSIDs.  This site contains two customers.  One customer is the Main customer with the second customer leasing space.
 
I have the Cust2 WLAN at the remote site set to have traffic egress out of a local interface on the 2500 WLC (this traffic is then tunnelled back to their Main location via an ASA which houses the DHCP scope for that vlan).    I can connect to this SSID, obtain an IP Address off the ASA and am tunnelling without issue.
 
For the Cust1 WLAN at the remote site, I would like to broadcast an SSID from the Main location on those same APs which are registered to the 2500.  It is my understanding, that I anchor the SSID at the Main site and identically configure the SSID at the remote site.  This will allow the end user to authenticate to the RADIUS server at the Main site and be placed upon the correct vlan (we are using DOT1x and dynamic vlans).
 
For my test, I am starting simple.  I have created a test WLAN with no authentication. At the main site, on 5508 WLC3, I have created the test WLAN, and placed the interface into a low security vlan (call it VLAN-low).  I have anchored this test WLAN to that controller.  At the remote site, I have created the same WLAN (but placed it into the management interface for now - the VLAN-low does not exist at the remote site) and configured that WLAN to anchor back to the WLC3 at the main site.  I am unable to obtain an IP address from the remote site.  I have placed the remote site WLC in the wlcMain-MG as well. How close does the code need to be on the controllers - the 5508s are at 7.0.116.0 and the 2500 is at 7.0.220.0? What could I be missing?

View 5 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved