Cisco VPN :: ASA5505 Tunnel Some Traffic (public Host) From Remote Site

Feb 6, 2012

On remote site I have Cisco ASA5505, on cental site I have Cisco 2811 router, working site-to-site VPN tunnel. [code]

View 1 Replies


ADVERTISEMENT

Cisco Wireless :: Configuring 5508 At Remote Site To Tunnel Traffic From WLC At Main Site?

Sep 20, 2012

At the main site, I have 3 5508 WLCs each part of a mobility group (wlcMain-MG).  In NCS, under "System/Mobility Groups" for each controller, I see each controller listed as "local" with the other Controllers listed with the group name "wlcMain-MG".  None of the SSIDs are "anchored".
 
I have a new site with a 2500 series WLC that I would like to push out 2 SSIDs.  This site contains two customers.  One customer is the Main customer with the second customer leasing space.
 
I have the Cust2 WLAN at the remote site set to have traffic egress out of a local interface on the 2500 WLC (this traffic is then tunnelled back to their Main location via an ASA which houses the DHCP scope for that vlan).    I can connect to this SSID, obtain an IP Address off the ASA and am tunnelling without issue.
 
For the Cust1 WLAN at the remote site, I would like to broadcast an SSID from the Main location on those same APs which are registered to the 2500.  It is my understanding, that I anchor the SSID at the Main site and identically configure the SSID at the remote site.  This will allow the end user to authenticate to the RADIUS server at the Main site and be placed upon the correct vlan (we are using DOT1x and dynamic vlans).
 
For my test, I am starting simple.  I have created a test WLAN with no authentication. At the main site, on 5508 WLC3, I have created the test WLAN, and placed the interface into a low security vlan (call it VLAN-low).  I have anchored this test WLAN to that controller.  At the remote site, I have created the same WLAN (but placed it into the management interface for now - the VLAN-low does not exist at the remote site) and configured that WLAN to anchor back to the WLC3 at the main site.  I am unable to obtain an IP address from the remote site.  I have placed the remote site WLC in the wlcMain-MG as well. How close does the code need to be on the controllers - the 5508s are at 7.0.116.0 and the 2500 is at 7.0.220.0? What could I be missing?

View 5 Replies View Related

Cisco Firewall :: ASA 5510 - Allow Only One Host Access To VPN Site To Site Tunnel

May 28, 2012

I have a ASA 5510 that has multiple site to site VPNs. I need to create an additiona site to site VPN but only allow 1 host to access and traverse the tunnel. The network is on a 192.168.5.x but the host that will need to access this tunnel needs to be on a 172.16.33.x network. I dont want any other traffic allowed to access or traverse the VPN tunnel for this host.  How can I set this up?

View 33 Replies View Related

Cisco VPN :: ASA5505 Add Site-to-site Tunnel On Top Of Existing Configuration

May 3, 2011

i have one asa 5505 that have classic remote access vpn set-up and now i need to add site-to-site tunnel on top of the existing configuration. Is that possible with asa 5505 and do i need some special IOS bundle for that? May i use vpn wizard for that or do i need to go through cli since remote access vpn is setup using wizard.

View 2 Replies View Related

Cisco VPN :: Site To Site Tunnel Is Up But ACL Is Not Working On ASA5505?

Oct 6, 2012

I have configured Site to site and the VPN tunnel is up. But the ACL's are not working.

View 11 Replies View Related

Cisco VPN :: ASA5505 Blocking Remote Network / Site-to-site Vpn

Jun 28, 2011

I have a site-to-site VPN already established, everything is working as it should.  I'm trying to block the remote network from accessing our network since we only need to access theirs.  I'm sure this is something very easy to implement with an ACL but I'm not sure where this rule needs to go. The VPN is on ASA 5505. 

View 5 Replies View Related

Cisco VPN :: ASA5505 Site-To-Site And Remote Access On Same Device

Jun 3, 2012

I'm attempting to configure an for both site-to-site and remote access VPNs.  The site-to-site is working fine, however when I connect using the Cisco client, after initial connection and password prompt I get a "not connected" status.  The log states that a policy map match could not be found.  I have successfully set the unit up for remote access with no site-to-site and ran into another host of issues when adding the site-to-site to the working remote access config, so I started over setting up site-to-site first.  I've attempted this through ADSM (hate it) - the current configuration is via CLI.  I'm certain I'm just missing a piece or two.

View 2 Replies View Related

Cisco VPN :: 506 Firewall 6.3(4) PDM 1.0 / Broke Remote VPN After Site To Site VPN Tunnel Created?

May 19, 2011

It's been a long time since I played in Cisco CLI.Using a Cisco 506 Firewall 6.3(4) PDM 1.0?Problem is I created a site to site tunnnel with a vendor and since then our remote VPN does not work. Completely times out so I am sure I broke something in the crypto map or something similar.
 
Tunnel is policy 10 using access-list 101
Remote VPN is Policy 20

Config Below:

: Saved:PIX Version 6.3(4)interface ethernet0 10fullinterface ethernet1 10fullnameif ethernet0 outside security0nameif ethernet1 inside security100enable password XLk0qAaMaA6kjvA6 encryptedpasswd VeCrsQbWdIFPwnny encryptedhostname RMS-DR-PIXdomain-name RMS.Localfixup protocol dns maximum-length 512fixup protocol ftp 21fixup protocol h323 h225 1720fixup protocol h323 ras 1718-1719fixup protocol http 80fixup protocol rsh 514fixup protocol rtsp 554fixup protocol sip 5060fixup protocol sip udp 5060fixup protocol skinny 2000fixup protocol smtp 25fixup protocol sqlnet 1521fixup protocol tftp 69namesobject-group network FTP_Clients description FTP Client PCs network-object host 192.168.xxx.xxx network-object host

[code]....

View 4 Replies View Related

Cisco VPN :: ASA 5505 - Users Aren't Able To Reach Remote Network Through Site-to-site Tunnel

May 21, 2011

Remote-access users aren't able to reach our remote network through a site-to-site VPN tunnel between two ASA 5505's.
 
I've seen several threads about that here, I've run through the walkthrough at [URL] I've taken a stab at setting split tunnelling and nat exemption, but it seems I'm still missing something. Remote-access users can reach the main site, but not the remote site.
 
Remote-access (vpn-houston) uses 192.168.69.0/24.
The main site (houston) uses 10.0.0.0/24
The remote site (lugoff) uses 10.0.1.0/24

View 5 Replies View Related

Cisco VPN :: ASA 5510 - Remote Clients To Site To Site Tunnel

Feb 20, 2013

I have a situation where I need to have remote users vpn into my ASA 5510 and then turn around and hit a site to site tunnel.  Now when I am in our office I can hit the site to site vpn fine.  When I am at home and vpn to the asa I can not get to the site to site resources. Do you see where my config is incorrect? result of the command: "show run"
 
ASA Version 9.1(1)
!
hostname xxxxx
domain-name xxxx
enable password xxxxx
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
[ code]....

View 3 Replies View Related

Cisco VPN :: 1800 Site-to-Site VPN Tunnel Bandwidth For Voice Traffic

Jun 22, 2011

I have some challenges with a VPN config I recently setup for a client.I have at the HO the following:

- 1800 router
- Avaya phones and Gateway
- 1MB radio internet access
 
At the BO(branch office), i have:

- 871 Router
- Avaya phones
- 256k internet bandwidth
 
The only reason we setup the VPN in the first place was for the phones at the BO to be able to connect to the gateway at the HO and also able to make calls and receive calls as if the phones were at the HO.The phones at the BO successfully register to the HO, but are unable to recieve calls and dial out. Everytime I try to make a call, the phone displays a "connecting..." message. [code]

View 2 Replies View Related

Cisco VPN :: ASA 5505 Site-to-Site VPN Tunnel Up But Not Passing Traffic

Apr 3, 2013

I do have a 5505 up and running, and passing data... url...Now I am trying to get a IPSEC VPN tunnel working.I actually have it up (IKE phase 1 & 2 both passed), but it is not sending/receiving data through the tunnel.
 
The networks concerned: name 10.0.0.0  Eventual  (HQ Site behind Firewall)name 1.1.1.0  CFS  (Public Network Gateway for Palo Alto Firewall - Firewall IP: 1.1.1.1)name 2.2.2.0  T1  (Remote site - Outside interface of 5505: 2.2.2.2)name 10.209.0.0  Local  (Remote Network - internal interface of 5505: 10.20 9. 0.3)  On a ping to the HQ network from behind the ASA, I get port map translation creation failed for icmp src inside:10.209.0.9 dst inside:10.0.0.33 (type 8, code 0)
 
I am suspecting that there is a NAT error and/or a lack of a static route for the rest of the 10.0.0.0 traffic, and that I may have to exempt/route the traffic for the HQ network (10.0.0.0), but I haven't been able to get the correct entries to make it work. [code]

View 22 Replies View Related

Cisco VPN :: 851 - Configure QOS For Voice Traffic Over Site-to-site VPN Tunnel

Jun 16, 2011

I want to configure QoS for voice traffic over a site-to-site VPN tunnel. I have a Cisco 851 router on the branch end and a Cisco 1800 router at the HQ. The setup is an Avaya Gateway located at the HQ and the idea is that the phones at the branch office are connected over the VPN tunnel to the gateway at the HQ.

I have a 1MB internet link at the HQ from a service provider and 256kbps internet link (from a different service provider) at the branch office. The branch office has just 3 users.

View 12 Replies View Related

Cisco VPN :: ASA5505 Remote VPN Using Site 2 Site VPN

Nov 14, 2011

I have 2 ASA 5505 firewall, Site 2 Site VPN working between two firewall. I attached visio diagram for my senario. I configured IPsec Remote VPN in ASA-01 firewall, a user able connted to ASA-01 network via modem through remote VPN. As i configured site 2 site VPN between two ASA, Is that possible that through remote VPN a user can able to connect to ASA-02.

View 2 Replies View Related

Cisco Firewall :: ASA5505 8.4.2 NAT To Forward SMTP And RDP Traffic To Internal Host

Nov 26, 2011

I am new to the ASA series and I am at a complete loss as to why I cannot configure this router to forward SMTP and RDP traffic to an internal host.
 
The packet trace tool in ASDM shows complete end-to-end connectivity for RDP but it still fails to connect from outside. This is my config file, what I need to change in order to make it work?

View 19 Replies View Related

Cisco VPN :: 876 ISR / Traffic From Easy VPN Client To Remote End Of Site-to-site?

Apr 27, 2011

A user with Easy VPN client connects to a 876 ISR (router A). This router also has a site-to-site VPN to another 876 ISR (router B). What I want to achieve is that the user dials in to router A and can access the network on the remote end of the site-to-site tunnel (router B) In diagram:
 
user (192.168.18.x) - Easy VPN - Router A (192.168.16.x) - sitetosite - Router B (192.168.17.x)
 
I have added routes in router B to the 192.168.18.x network with router A as next hop, but I can't reach the other segment.

View 1 Replies View Related

Cisco VPN :: 2611xm - Unable To Ping Remote Host Through Tunnel?

Apr 20, 2012

I am in a test environment using an ASA 55005 and a Cisoc 2611xm router. ASA is running version 8.4 and router is running is ios12.4. My VPN tunnel comes up but I am unable to ping between remote hosts. I used the ASDM and SDM for the configuration. Attached is a copy of both configs.

View 8 Replies View Related

ASA5505 - Tunnel A Specific Traffic Via VPN

May 20, 2012

I have a number of sites in China, they have decent inter-country connectivity but poor connectivity when going overseas.

We have a single site in China witha dedicated 1:1 leased line that has good conectivity both inside and outside of China.

All the sites in China have ASA5505 firewalls

One of our Citrix farms is hosted in the UK and although the main site with the leased line is fine accessing the farm the other sites are not. I would like to try and tunnel just the citrix connectivity via a VPN to the China head office then use their connection to get out to the farm.

how to tunnel all traffic but not just specific traffic over the VPN.

View 3 Replies View Related

Cisco VPN :: Tunnel Between Asa5505 And Fortigate 80c Up But No Traffic

Nov 27, 2011

I have set up an ipsec tunnel between a Cisco ASA 5505 and a Fortigate 80c. The tunnel is set up as I execute pings from inside behind ASA to inside behind FG, however I cannot get connectivity to hosts behind the Fortigate (traffic is allowed through policies configured on the FG). What I noticed in packet tracer is that traffic is dropped at the step 'Vpn lookup' To troubleshoot I have configured a test ('fake') vpn connection through the vpn wizard and get the same result in packet tracer. I run 8.4 software on the ASA and this is part of the relevant config.

View 1 Replies View Related

Cisco VPN :: ASA5505 / PIX 515E - How To Get VPN Up From Out Remote Site

Feb 27, 2013

I'm having a Issue getting my VPN up from out remote site . We have a ASA5505 at the remote site and the Main office we have a  PIX-515E.. I followed this temp config I found on line but Im still not able to get the VPN UP..

This script can be used to get you started on a site to site vpn using the older Cisco PIX code. PIX running 6.3 ! ^^^^ Set ISAKMP (phase 1) parameters ^^^^^ {code]... 
 
When I log into the ASA and run these commands This what I get
 
Colort2# sh run crypto isakmp
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
[code]...

View 1 Replies View Related

Cisco VPN :: ASA5505 - Remote Client To Browse Internet Through Tunnel?

May 28, 2011

inside network----ASA5505========internet===========Remote VPN client.
 
The ASA has one public IP on its outside interface and using PAT to the internet. It only has two interfaces, inside and outside using vlan. I created a IPSec VPN through CLI. My goal is for the remote client to browse the Internet throught tunnel.
 
Q1: Is it possible?

Q2: The remote side gets connected and has IP from the pool, with is part of inside network. But it cannot ping anything, including the gateway, which is the inside interface. I debug it, it shows the ASA receives the ping packages, but it doesnt send anything back to the client.

View 5 Replies View Related

Cisco :: Reach To Remote Site Via SSLVPN (ASA5505)

Feb 10, 2011

I'm having some troubles with SSLVPN connectivity. I've setup SSLVPN at one site and it works great with web access, file share, RDP plugin etc. at the local LAN on that site. But I also would like to reach another site (connected with an IPSEC tunnel). Is this possible? if it is, how do I do it?Both firewalls are ASA5505, one 8.31 and one 8.22 Just a note, it works to connect with IPSEC client and reach the remote site just fine.

View 8 Replies View Related

Cisco WAN :: C3750 - Mirror Switch Port Traffic To Remote Host IP Address?

May 31, 2013

Is there any way to Mirror a CISCO C3750 Switch Port Taffic to a remote Host IP Address?I know Port Mirror (SPAN/RSPAN) can copy one Interface Packet to another Interface. But I am looking for a way to miror Switch Port Packets to a remote Host (having Public IP Address and running Wirehark). Is it possible?

View 9 Replies View Related

Cisco Firewall :: ASA5510 - Web Interface On NAS From Remote Site Across VPN Tunnel?

Dec 3, 2012

I have two routers on my internal network.

10.10.199.106 is a Cisco ASA5510.

10.10.199.108 is a Sonicwall NSA 3500
 
The sonicwall handles our site to site VPN tunnels.  The Cisco handles our client to site VPN connections.
 
I have a unit that points to 10.10.199.106 (Cisco) for internet access.  All other clients on the network point to 10.10.199.108 (Sonicwall) for internet access.The device in question, a Synology NAS, is using 10.10.199.68 as it's IP address.
 
I'm trying to hit the web interface on the NAS from a remote site across our VPN tunnel.  The IP scheme on the remote end of the VPN tunnel is 192.168.72.0/24.
 
Going through the VPN, I can hit every object on the network that uses .108 (Sonicwalll) as it's gateway.  However, I cannot hit the unit that uses .106 (Cisco) as it's gateway. 
 
I added a route statement (using ASDM) that routes all traffic destined to 192.168.72.0/24 to the Sonicwall so it can send it back down the VPN tunnel.  If I'm understanding routing correctly, this should allow responses from NAS destined for 192.168.72.0/24 to go back down the VPN tunnel.

View 4 Replies View Related

Cisco Routers :: Setup VPN Tunnel Between Linux Machine And RVS4000 At A Remote Site?

Jul 21, 2011

I'm trying to set up a VPN tunnel between a Linux machine and a RVS4000 at a remote site (served via satellite connection). After many efforts, I finally succeeded (based on Openswan). However, while PINGing is OK, big packets (from the RVS4000 LAN to the Linux box) arrive corrupted.
 
I lowered the WAN MTU, with no success. What finally did the trick is to lower the MTU at the RVS4000 LAN interface. Since this is not possible via the Web I/F, I did it via telnet ("ifconfig eth0 mtu 1400"). However, this change is lost after router reboot. How can I make the LAN MTU setting permanent?

View 1 Replies View Related

Cisco Routers :: RV180 To Setup A VPN Tunnel Between Remote Site And Central Office

Aug 18, 2012

I bought 2 RV180 to setup a VPN tunnel between a remote site and central office.The VPN tunnel is established, I can ping from central office to remote site but browsing on that server fails. [code]
 
Seems the routing is not really working through the VPN Tunnel.

View 4 Replies View Related

Cisco VPN :: Pix 515e - Remote Host Cannot Ping Any LAN Host

Jun 27, 2011

I have a host that can successfully connect to a PIX 515E (7.x OS) via VPN Client; however, I have no IP routing to the LAN from the remote host.The VPN IP pool works finem,The LAN default gateway is the inside interface on the PIX; the network is flat L2 behind it.The default route on the PIX points out; no other routes are defined,The VPN remote host can be pinged from LAN hosts, but the VPN remote host cannot ping any LAN host, not even the PIX inside interface.

View 2 Replies View Related

Cisco VPN :: ASA 5505 / Site To Site Vpn With One Site Always Initiate A Tunnel?

Feb 7, 2011

I have ASA 5505, i configured site to site vpn between central site and remote site and is working. Now the problem is we use remote site for troubleshooting purpose, so we need to create a tunnel from remote site to central site. I need to configure such a way that remote site can craete a tunnel to central site, but central site not able to create a tunnel, it just respond to remote site.

View 3 Replies View Related

Cisco VPN :: 5510 Site To Site VPN Access To Servers With Overlapped Remote Site

May 18, 2012

I have a requirement to create a site to site vpn tunnel on ASA 5510 from a remote site to my HO, ihave already other site-to-site tunnels are up and running on the ASA.The issue is my remote site has got the network address which falls in one of the subnet used in HO(192.168.10.0/24).My requirement is only  My remote site need to accees couple of my servers in HO which is in 192.168.200.0/24 subnet.

View 2 Replies View Related

Cisco Firewall :: ASA 5505 / Site To Site VPN Using Public Addresses On Local Network

Jul 28, 2011

I have a request to establish a site to site VPN with a customer. While collecting the information I give them our local network subnet which is a private subnet (192.168.5.0). They asked me if I could give them a public address instead. They can not work with the 192.168.5 subnet. Is this possible?
 
My side of the VPN is an ASA 5505 running 8.2(2). The other side i believe is a Checkpoint.

View 5 Replies View Related

Cisco VPN :: 5520 Requirement To Terminate Site-to-site VPN From Remote Site

Jun 17, 2012

We have ordered a pair of Cisco ASA5520 (ASA5520-BUN-K9).Now there is a requirement to terminate site-to-site VPN from remote site. Do we need VPN plus licence for this and how much it cost?

View 1 Replies View Related

Cisco VPN :: 877 / How To IPsec Site To Site Vpn Port Forwarding To Remote Site

Jun 13, 2012

The scenario where a Site to Site VPN tunnel has been established between Site A and Site B. Lan on Site A can ping Lan on Site B. My problem is a Printer behind Site B needs to be accessed by using the WAN IP address of Site A. Also i could not ping the remote lan or printer from the router.
 
Below are my configure on the Cisco 877 in site A.  
 
Building configuration... 
Current configuration : 5425 bytes
!
! Last configuration change at 15:09:21 PCTime Fri Jun 15 2012 by admin01
!
version 12.4
no service pad

[code]....

View 1 Replies View Related

Cisco VPN :: 5505 - Site To Site Connected But Cannot Ping Remote Site

Oct 11, 2011

cisco products and am struggling getting a VPN going between an ASA 5505 and 5510.  I have a VPN created (using the VPN wizward on both) and it shows the VPN is up, but I can't ping the remote site (from either side).

View 11 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved