i configured site to site VPN beetwen the asa 5505 (asa 8.4.2) and the asa 5510 (asa 8.4.4). how i can configure that the users from one side and second side use internet in same time?
View 13 Repliesi have 2 router asa 5505 with base license i wanna make site to site vpn connection and remote site using vpn client to connect first i have hdsl router with 5 public ip i wanna try it by giving 1 public ip to each router and try the vpn but nothing work?
View 1 Replies View RelatedWe've just deployed a site-to-site VPN using a 5505 ASA on the client's site and a checkpoint Nokia FW on our site. Everything seems to be fine except that the user's connections to their file shares seem to be intermittently dropping. One minute the connection to the shares is there, next thing it's lost. There is no logic to it because no two users are experiencing issues at the same time, as a matter of fact even on the same PC where a user has access to 3 shares on 3 different servers, one could be showing as connected whereas the other two be dropping. [code]
As you can see the Duplex and Speed are set to auto, I've rectified this since then and I'm keeping a close eye on the output errors, and collisions. However, I'm afraid that this did not rectify the issue and the users are still experiencing intermittent connection dropping to their file shares over the VPN!
im drawing a blank trying to setup a site to site connection with a 5505 ASA using ipsec and isakmp.i have the pre shared key as well as the external address of the other end of the tunnel but do not remember what the commands are to setup the crypto map and isakmp.
View 7 Replies View RelatedI would like know is that possible to connect two 5505 ASA in site to site VPN with 1 site using ADSL pppoe connection?
View 5 Replies View RelatedWe have a site to site client that is having issue with intermittent disconnects. The Main endpoint is a CIsco ASA 5520 8.4.3 and the remote site has a a Cisco ASA 5505 8.2.5.
If we have a disconnect, we can "logout" of the Main ASA and the connection seems to find itself and traffic will flow. This take place about every 1 - 5 minutes but if you reset the crypto (which I am assuming you do) by logging out under the Logging Monitor Session - ikev1 sessions. It all starts right back up.
I am stumped. At first I thought MTUs but I am not sure that is the answer.
cisco products and am struggling getting a VPN going between an ASA 5505 and 5510. I have a VPN created (using the VPN wizward on both) and it shows the VPN is up, but I can't ping the remote site (from either side).
View 11 Replies View RelatedI have ASA 5505, i configured site to site vpn between central site and remote site and is working. Now the problem is we use remote site for troubleshooting purpose, so we need to create a tunnel from remote site to central site. I need to configure such a way that remote site can craete a tunnel to central site, but central site not able to create a tunnel, it just respond to remote site.
View 3 Replies View RelatedI would like to know both Cisco 2901 or 2921 router and Cisco 5505 ASA can build site to site VPN.
1) what is the different to build site to site VPN between router and firewall ?
2) which is the best choice if using in site to site VPN connection ?
I have a request to establish a site to site VPN with a customer. While collecting the information I give them our local network subnet which is a private subnet (192.168.5.0). They asked me if I could give them a public address instead. They can not work with the 192.168.5 subnet. Is this possible?
My side of the VPN is an ASA 5505 running 8.2(2). The other side i believe is a Checkpoint.
Got an ASA5505 connected to another endpoint running IPsec and being NAT'd at each end to a 10.0.0.0/24 network. I can pass other types of traffic through the ASA 5505 but not RTP traffic. The moment it is NAT'd and hits the firewall rules it gets denied by the default deny at the bottom of the list.
Currently the rules are as follows
Incoming External
allow ip any any
allow tcp any any
allow udp any any
default deny
[code].....
It wont allow us to setup a voip call...however when the same call manager sets up a voip call NOT using this ipsec tunnel it works just fine.
Got an ASA5505 connected to another endpoint running IPsec and being NAT'd at each end to a 10.0.0.0/24 network. I can pass other types of traffic through the ASA 5505 but not RTP traffic. The moment it is NAT'd and hits the firewall rules it gets denied by the default deny at the bottom of the list.
Currently the rules are as follows
Incoming External
allow ip any any
allow tcp any any
allow udp any any
default deny
[code]....
It wont allow us to setup a voip call...however when the same call manager sets up a voip call NOT using this ipsec tunnel it works just fine.
We have a client that has a Cisco 1801W Firewall that is setup as a site to site VPN terminating to a Cisco ASA 5505. The tunnel is up and established, I can ping from both sides of the tunnel.
The problem is the clients behind the Cisco ASA (192.168.2.x) cannot reach certain ports behind the Router (192.168.1.x). The main thing we're trying to do is browse via UNC path (ex: \192.168.1.120 from a 192.168.2.x machine).
I got 3389 working after I changed the - ip nat inside source static tcp 192.168.1.120 3389 y.y.x.x 3389 route-map DM_RMAP_1 extendable Modified the command to include the public IP instead of interface FastEthernet0
I believe it has something to do with the way NAT and route-maps are setup currently but I'm not familar enough with them to make the changes. I worked with Cisco to ensure the VPN tunnel was fine and it's something security related on the Router.
Here is the configuration (removed a few lines not necessary. y.y.x.x = WAN IP of Router x.x.y.y = WAN IP of ASA).
Building configuration...
Current configuration : 23648 bytes
!
version 12.4
no service pad
[Code].....
Need to know the step by step procedure for monitoring site-to-site VPN tunnel (up/down) using SNMP on Cisco ASA 5505.
View 1 Replies View RelatedI have tried Cisco presales but got bounced - go Cisco !So, i have a small customer who requires a single device which will provide .....
1/ Leased Line connection @ 10mb
2/ ADSL failover onbox (so configurable from CLI, unlike the 860’s which I see only have one ‘active’ wan port)
3/ IOS based
4/ integrated 4 ports (min) switch
5/ site to site VPN
6/ up to 10 x SSLVPN remote users
I did pitch in with ASA5505 with external ADSL router but he is “space-constrained”.It worries me when Cisco doc's say only one WAN port is 'active' - since it doesn't say the second port automatically comes up if the first goes down so I can't take a gamble on that being the case.
I've set up a standard site-to-site VPN between 2 ASA 5505s and the VPN is working fine for traffic between these ASAs and computers which are in the same LANs.but when I'm trying to connect to computers which are in another VLAN I have a problem.
View 1 Replies View RelatedI have weird problem with a Site to site VPN tunnel from a Cisco ASA 5505 to an Clavister Firewall.When I restart the Cisco ASA 5505 the tunnel is up and down,up, down, down, and I get all strange messages when I see if the tunnel is up or down with the syntax: [code]
After a while like 5-10 min the vpn site to site tunnel is up and here is the strange thing happening I have all accesslists and tunnel accesslists right I can only access one remote network (Main site Clavister Firewall) trought the vpn tunnel behind the Cisco ASA 5505, and I have 5 more remote networks that I want to access but only one remote network is working trought the vpn tunnel behind the Cisco ASA. I see that when I do this syntax in ASA: show crypto ipsec sa.They had a Clavister Firewall before on that site before and now they have a Cisco ASA 5505 and all the rules on the main site thats have the big Clavister Firewall is intact so the problems are in the Cisco ASA 5505. [code]
All these remote networks are at the Main Site Clavister Firewall.
I have an ASA5505 running which is on a static IP. I have just got an SRP527W for a remote worker and want to create a site-to-site VPN into the ASA. I have a number of other router of non-cisco brand which just all dial-in and connect no problem.
On other routers I have been abloe to specify the DDNS hostname in the VPN setup so that the ASA can identify it. I'm not sure how I setup the SRP527 to connect to the ASA.
I have 2 ASA 5505 Firewall, I Configured Site 2 Site VPN no both the fitrewall, as i have a dual ISP, i am able to create the tunnel with primary but once my primary is down i am not able to create the tunnel with back up ISP. During the troobleshoothing by typing Show isakmp sa and Show ipsec sa, i can see my tunnel is up, but not able to decap the packets.
As it will look like
#pkts encaps: 15, #pkts encrypt: 15, #pkts digest: 15 #pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0 #pkts compressed: 0, #pkts decompressed: 0 #pkts not compressed: 15, #pkts comp failed: 0, #pkts decomp failed: 0 #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0 #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0 #send errors: 0, #recv errors: 0
I wanted to know the maximum VPN client sessions (using the Cisco VPN client) and Site-to-Site VPN tunnels that I can connect to my ASA 5505 simultaneously.
In other words, if I have x VPN clients and y Site-to-Site tunnels, at any time, does x + y have to be <= 10 (Total VPN Peers)? If yes, can I upgrade to the security plus license to increase the Total VPN Peers to 25?
Licensed features for this platform:
Maximum Physical Interfaces : 8
VLANs : 3, DMZ Restricted
Inside Hosts : Unlimited
Failover : Disabled
VPN-DES : Enabled
[Code]...
Remote-access users aren't able to reach our remote network through a site-to-site VPN tunnel between two ASA 5505's.
I've seen several threads about that here, I've run through the walkthrough at [URL] I've taken a stab at setting split tunnelling and nat exemption, but it seems I'm still missing something. Remote-access users can reach the main site, but not the remote site.
Remote-access (vpn-houston) uses 192.168.69.0/24.
The main site (houston) uses 10.0.0.0/24
The remote site (lugoff) uses 10.0.1.0/24
Last week, I was able to establish a site-to-site VPN tunnel between an ASA 5505 and Cisco C881 router just fine. The tunnel was up and and running for a number of days but today the tunnel is no longer up. I was wondering how, if there are any commands to re-establish or re-initiate the tunnel.
View 3 Replies View RelatedI have a 5505 asa code version 8.3(2). Trying to set up a site to site tunnel with someone and he is asking if I can use ike v2. How do I go about setting up the tunnel to use ikev2? Is ikev2 an option with site to site tunnels?
View 5 Replies View RelatedASA is configured with the VPN site to site using the wizard, created the Public IP of contivity, local and remote LAN . I attached the configuration. In contivity have the following settings: Not able to communicate both subnets.Do I need to configure IP subnets and published in the contivity as was done in the ASA?
View 3 Replies View RelatedI am not very experienced with Cisco networking.
Here is the situation.
Site A - headquarters 192.168.1.x
Site B - remote office 192.168.20.x
Site C - remote office 192.168.30.x
Site A - ASA 5510
Site B - ASA 5505
Site C - ASA 5505
Site-to-site VPN is established and works between A and B, A and C. Users would like to establish a tunnel between B and C to work on a common project and the data is on Site B.
I tried configuring the S2S VPN with pre-shared keys on both firewalls at sites B and C but in the end it is not established (I cannot ping either side). I used the Wizard interface multiple times and one time the CLI. I generally followed the settings chosen between the headquarter and the individual remote sites and tried to replicate them. Obviously I have made a mistake somewhere.
Could there be any limitation on the ASA 5505 in terms of licensing and the number of S2S tunnels?
i have a client who needs to establish a VPN tunnel from his satellite office (Site A) to his corporate office (Site Z). His satellite office will have a single PC sitting behind the ASA. In addition, he needs to be able to VPN from his home (Site H) to Site A to access his PC.The first question I have is about the ASA 5505 and the various licensing options. I want to ensure that an ASA5505-BUN-K9 will be able to establish the site-to-site tunnel as well as allow him to use either the IPsec or SSL VPN client to connect from Site H to Site A. Secondly, I would like to verify that no special routing or configuration would need to take place in order to allow traffic not destined for Site Z (i.e., general web browsing or other traffic to any resource that is not part of the Site Z network) to go out his outside interface without specifically traversing the VPN tunnel (split tunneling?)Finally, if the client were to establish a VPN session from Site H to Site A, would that allow for him to connect directly into resources at Site Z without any special firewall security rules? Since the VPN session would come in on the outside interface, and the tunnel back to Site Z goes out on the same interface, would this constitute a split horizon scenario that would call for a more complex config, or will the ASA handle that automatically without issue?
View 1 Replies View RelatedJust now my boss asked me to prepare to set up site-to-site VPN on Cisco 881 Integrated Services router to ASA 5505 router which is now running at the HQ side. I am now learning pdf file from Cisco which mention how to setup site-to-site VPN between Cisco 1812 IOS router and ASA 5505 router by using ASDM V6.1 and SDM V2.5. Can't find the paper for that Cisco 881 device.
View 4 Replies View RelatedWe have got site to site VPN configured between local site with PIX515 6.3(5) and remote site with ASA 5505 7.2(4) . Because of very unreliable internet connection in remote site , we have added new ISP link which we want to use as redundant link .i understand ASA 5505 can be configured with two ISP link with SLA monitor method for redundancy as per this document ,[URL]
my question is how do i set up this pix 515 to have redundant VPN tunnel with remote site (when primiary ISP link fails in remote site and secondary ISP links takes over ) . I was thinking of using PIX 515 with 2 peers in same crypto map used for that sepcific site to site vpn tunnel,not sure that is the right way or not though.But how would i configure ASA 5505 to use backup interface(where secondar isp router conects ) to particitae in Site to site Tunnel .
I am using a Cisco ASA 5505 Here is a description of my topology.
Headquarters = 192.168.201.0
Client X = 172.16.0.0
Datacenter = 10.12.0.0
Site to Site Tunnels:
Headquarters ---> Datacenter
Datacenter ---> Client X
I want to ability for computers in the Headquarters subnet to access the Client X subnet.I have tried setting up a static route to push all traffic destin for 172.16.0.0 to the datacenter, but was unsuccessful. how I can route all 172.16.0.0 through the tunnel.I have tried ading a static route on my ASA but without success.
Any experience setting up a site-to-site VPN between a ASA 5505 running 8.3 code and Windows Server 2008 R2?
View 1 Replies View RelatedWe have a Cisco ASA 5510 at our main office that makes connection with a 5505 at our other office using site to site VPN. (works)
Now for the question,
we want to access our other office from the main office but we wont want them to have access to our servers etc. so basically we want to control them but they shouldn't have the rights to control us.
Is this possible with a site to site VPN? and how to do it.
I do have a 5505 up and running, and passing data... url...Now I am trying to get a IPSEC VPN tunnel working.I actually have it up (IKE phase 1 & 2 both passed), but it is not sending/receiving data through the tunnel.
The networks concerned: name 10.0.0.0 Eventual (HQ Site behind Firewall)name 1.1.1.0 CFS (Public Network Gateway for Palo Alto Firewall - Firewall IP: 1.1.1.1)name 2.2.2.0 T1 (Remote site - Outside interface of 5505: 2.2.2.2)name 10.209.0.0 Local (Remote Network - internal interface of 5505: 10.20 9. 0.3) On a ping to the HQ network from behind the ASA, I get port map translation creation failed for icmp src inside:10.209.0.9 dst inside:10.0.0.33 (type 8, code 0)
I am suspecting that there is a NAT error and/or a lack of a static route for the rest of the 10.0.0.0 traffic, and that I may have to exempt/route the traffic for the HQ network (10.0.0.0), but I haven't been able to get the correct entries to make it work. [code]
We are setting up a new phone system using the UC540 with a VPN connection between 2 buildings using 2 Cisco ASA 5505's at either end.The problem I am having is getting the phones at the remote site to connect to the UC540 at the main site.
Phones/Computers (10.0.1.0/24) -- ASA -------------VPN Tunnel------------- ASA -- UC540 -----------Data Vlan1 (10.0.0.0/24)
|------Voice Vlan100 (10.1.1.0/24)
What i am told by UC500 support is that the phones at the remote site will connect if they have connectivity to the TFTP subnet on the UC540, which is 10.1.10.0/30 I added the static route on the ASA and I can ping the 10.1.10.1 TFTP server on the UC540 from the ASA, but not for any other device on the 10.0.0.0/24 network, such as the DC. I added the static route there and was able to ping, so something in the ASA seems to be preventing it.
I also can't seem to get the ASA at the remote site to ping 10.1.10.1. I've tried adding the static route there in hopes it would forward it through the VPN tunnel.