Cisco VPN :: Unstable IPSEC Tunnel Between 892 And Chkpt VSX R67 / ISAKMP
Jun 29, 2011
I am currently experiencing an issue with an IPSEC Tunnel between a Cisco892-K9 (c890-universalk9-mz.124-22.YB.bin / Feature: advipservices) and a Checkpoint VSX R67.
After reloading the router the tunnel is stable, but afterwards we loose the connection to the LAN unexpectidly (max. time of the connexion is ~2h30).
In fact after a reload the first ISAKMP SA is well negotiated with conn-id 2001 and after a certain amout of time the connexion is lost always associated with this debug message =>
ISAKMP:(2001):error from epa_ikmp_gen_ipsec (QM_IDLE )
ISAKMP:(2001):Unable to generate IPsec key for 799280698!
ISAKMP:(2001):deleting SA reason "Death by retransmission P2" state (I) QM_IDLE (peer 194.X.X.X)
and so on ....
We supposed it was related to DPD messages so we deactivated the keepalive (no crypto isakp keepalive). We tried to play also with the ACL matching the crypto map (currently from local subnets to any), but still no luck.
When it is stable the ‘show crypto isakmp sa’ indicates a isakmp sa ‘QM_IDLE / ACTIVE), and when the problem occurs the active ISAKMP SA is deleted and recreated (in ACTIVE state) continuously : conn-id 2001, 2002, 2003, 2004 etc...…but still no access to the LAN.
My main question is to know if someone has already know the signification of the previous ISAKMP debug messages (along with the total debug message + crypto conf from the beginning of the problem) =>May it be a platform support (near 200 ipsec flow in use => most subnet to subnet flow, few subnet to host flows- 200 users on site) , compatiblity, crypto map acl …???
View 5 Replies
ADVERTISEMENT
Dec 14, 2011
I have a couple of clients which are using the 3g modem to connect to ASA.The channel was sometimes "noisy" and therefore ipsec isakmp is doesn't work.Client losts vpn connection ,but on asa i can see it as connected(connection was in "freeze" state).
It's look like this :
[code]...
View 4 Replies
View Related
Feb 25, 2012
I have setup ipsec VPN in my C2811 router but when "show crypto isakmp/ipsec sa" shows nothing. Remote end point is an "ASA5520". Does it indicates that the remote ASA5520 not yet configured?
Code...
View 9 Replies
View Related
Jan 30, 2012
We have Cisco SA520 and we want to use VPN to access the office servers from home. We have been able to configure the VPN server on the SA520 however the connection is very unstable.We use OS X 10.7 lion built-in Cisco compatible VPN clients and this is a typical output of ping from 3G mobile network to a server inside the office network. It works the same way also if I am trying to access from my home ADSL connection so the problem is not the instability of the 3G connection.
Some sample traffic sequeezed:
PING ns.svm (192.168.60.27): 56 data bytes
64 bytes from 192.168.60.27: icmp_seq=0 ttl=63 time=98.022 ms
64 bytes from 192.168.60.27: icmp_seq=1 ttl=63 time=76.934 ms
64 bytes from 192.168.60.27: icmp_seq=2 ttl=63 time=278.201 ms
[code]....
View 1 Replies
View Related
Oct 24, 2012
I have a dynamic VPN site to site between a Firewall ASA 5510 with ASA version 8.2(1) (firewall ASA have a Static IP 201.111.14.114) and a C870 ISR (the ISR have a dynamic IP). The tunnel and the conectivity in both sides is successfull, however each time that occurs a interface restart because the Internet link is unstable in ISR side the VPN tunnel does not going to UP STATE again
These are the ISR logs listed when VPN going to DOWN
*Mar 10 13:58:45.157: %LINK-3-UPDOWN: Interface ATM0, changed state to down
*Mar 10 13:58:46.157: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0, changed state to down
[Code]......
View 2 Replies
View Related
Aug 8, 2011
im drawing a blank trying to setup a site to site connection with a 5505 ASA using ipsec and isakmp.i have the pre shared key as well as the external address of the other end of the tunnel but do not remember what the commands are to setup the crypto map and isakmp.
View 7 Replies
View Related
Sep 23, 2012
I'm in process of purchasing a new Cisco routers for our branches that will be used primary to enable IPSec virtual tunnel interfce with "tunnel mode ipsec ipv4". does the default IOS IP Base supports this feature? or i need to purchase DATA license or SECURITY license?
View 4 Replies
View Related
Oct 17, 2012
I am using a Cisco RV110W (Firmware 1.2.09) in a branch and I would like to create a VPN Tunnel to another site that has a Cisco RV042 (firmware v4.2.1.02)
What would be the correct Configuration? the current configuration I am using is
in the RV042 i am using
Check Enable
Local Group Setup
Local Security Gateway Type : IP Only
IP Address : RV042 Pulbic IP address
[Code].....
View 3 Replies
View Related
Oct 19, 2011
- Ipsec tunnell between two 881's
- An Aruba access point trying to set up a tunnell back to controller through the ipsec tunnell, on udp 4500
- Even though traffic shouldn't be NAT'ed (and other traffic is not), udp 4500 is NAT'ed
I guess this might be default behaviour, thing is that it used to work when it was set up as a route based easy vpn.
View 1 Replies
View Related
May 4, 2011
how to create ip sec tunnel using these parameters. customer ip where tunnel has to be connected 1.1.1.1
ISAKMP Parameters: (Phase I)
Encryption: AES-256 or 3DES
Authentication Mode: Pre-shared key
[Code]......
View 4 Replies
View Related
Mar 9, 2011
We have a Cisco 2820 that serves as a hub and our spokes are Cisco 871s. Its been working for a while and for some reason last week. Http and https traffic over the tunnel is having connection issues. I can Remote desktop or PCanywhere into the remote PCs. From that PC I can ping internal IP address or IP of the webmail server or internal webserver with no issue. But if I access it over the browser it times out or it will work and stop working again. Basically ica, icmp, pcanythere, rdp traffic works over the tunnel but not http or https.
View 2 Replies
View Related
May 4, 2011
can I force an IPSEC L2L tunnel to use NAT-T encapsulation no matter what? Automatic detection says none of the endpoints are behind NAT. I know I can disable it by the "crypto map XXX set nat-t-disable" command, but I want the exact opposite.
I have a very strange issue where asynchronos routing is making my life as a technician very hard.
A side question; Can I do something about an ISP that is policy-base-routing its ESP traffic (and/or translating it)?
ASA5505 ===>===>===> ISAKMP traffic ===>===>===> ASA5510
212.178.155.73 80.62.yyy.xxx (traffic source IP: 212.178.155.73)
[Code].....
View 3 Replies
View Related
Aug 8, 2012
i am curently troubleshooting a ipsec l2l VPN between
1. ASA 7.2(4) to SSG-140
2. Cisco 871W to SSG-140
In both scenario's the tunnel is nicely established, and traffic goes into the tunnel, but nothing comes out. All encap's, but no decap's
It seems like a routing issue, but we can not find anything on both sites.
So maybe i m running into a (known) issue between cisco VPN equipment and the SSG-140?
Could it be a proxy-id issue? Cause they configure stuff like 10.1.1.0/24 and i configure 10.1.1.0 0.0.0.255
View 7 Replies
View Related
Mar 24, 2011
I'm attempting to configure a tunnel on a PIX-501 version 6.3. It's an old device that's due to be replaced soon, but unfortunately we need a tunnel now... I have been using this document as a reference (6211): URL ,The remote end is a sonicwall.
The problem seems to be that the pix never sees the interesting traffic for the tunnel, and never tries to initiate a connection. I have enabled crypto ipsec and crypto isakmp debugs, but no data is ever displayed, even when attempting to access a device on the remote side of the tunnel! Someone had tried to set up this device with some tunnels in the past, but was never successful, so I'm thinking there might be remaining commands in the running-config causing problems.
View 7 Replies
View Related
Oct 29, 2012
configuring some static NAT entries on a remote site 887 router which also has a IPSec tunnel configured back to our main office.
I have been asked to configure some mobile phone "boost" boxes, which will take a mobile phone and send the traffic over the Internet - this is required because of the poor signal at the branch. These boxes connect via Ethernet to the local network and need a direct connection to the Internet and also certain UDP and TCP ports opening up.
There is only one local subnet on site and the ACL for the crypto map dictates that all traffic from this network to our head office go over the tunnel. What I wanted to do was create another vlan, give this a different subnet. Assign these mobile boost boxes DHCP reservations (there is no interface to them so they cannot be configured) and then allow them to break out to the Internet locally rather than send the traffic back to our head office and have to open up ports on our main ASA firewall.
[URL]
So I went ahead and created a separate vlan and DHCP reservation and then also followed the guidelines outlined above about using a route-map to stop the traffic being sent down the tunnel and then configured static NAT statements for each of the four ports these boost boxes need to work. I configure the ip nat inside/outside on the relevant ports (vlan 3 for inside, dialer 1 for outside) The configuration can be seen below for the NAT part;
! Denies vpn interesting traffic but permits all otherip access-list extended NAT-Trafficdeny ip 172.19.191.0 0.0.0.255 172.16.0.0 0.3.255.255deny ip 172.19.191.0 0.0.0.255 10.0.0.0 0.255.255.255deny ip 172.19.191.0 0.0.0.255 192.168.128.0
[Code].....
View 1 Replies
View Related
Mar 3, 2011
I have been struggling for a few days with getting site-to-site traffic working across a L2L IPSec tunnel. At this point, I have the tunnel up, and I see packets being decrypted on the correct IPSec SA's when I ping from a local network computer on the ASA side to a local network computer on the router side. I cannot ping from one side to the other, but those packets are getting through. We have another L2L tunnel that is from that ASA to another remote site's ASA, and that is functional. I have mirrored the configuration for ACLs, etc. from that site, so I believe that the issue is with the packets getting incorrectly translated by the NAT/NONAT statements/ACLs on the router side.
View 8 Replies
View Related
Nov 28, 2012
since a few days I'm trying to solve a problem. I've successfully established an IPSec tunnel between two local LANs. In the main office I'm working with a ASA5510 CLI 8.4 and a static public IP address. The branches are using different Cisco 8xx routers and dynamic public IP address. The following picture shows the current configuration:As I mentioned an IPSec Tunnel between the main office "Intern"-LAN 192.168.1.0/24 and an outside LAN 10.10.0.0/24 is successfully established. Now there is a new intern "Admin"-LAN 192.168.2.0/24 at the main office. The users from the outside LAN 10.10.0.0/24 need the possibility to reach this new intern "Admin"-LAN.Can I simply route the traffic from 10.10.0.0/24 to 192.168.2.0/24 via the existing IPSec-Tunnel? Or need I a new IPSec tunnel between the outside 10.10.0.0/24 LAN and the new "Admin"-LAN 192.168.2.0/24?
View 5 Replies
View Related
Aug 24, 2012
I'm going to implement a S-2-S VPN IPSec connection between 2 locations and I've to NAT incomming and outgoing traffic.
View 4 Replies
View Related
May 20, 2013
I have an ASA5510 configuration that I'd like to add to.In this configuration there is a site to site IPSEC VPN tunnel to a remote location.It is tunneling a particular subnet for me and everything is working.In the remote subnet, there is an ASA 5525-x connected on the outside interface. Let's say for argument's sake, the outside IP is 210.0.0.1.On the Inside interface, i've configured 10.240.32.0/24 network.The only static route I have configured on the 5510 is the default gateway that goes to the ISP.I assumed that I have to add: route Outside 10.240.32.0 255.255.255.0 210.0.0.1 1.I did this, but i'm not able to reach the destination 10.240.32.0/24 network. I can't see anything hitting the 5525-x and the only thing I see on the 5510 is the building outbound ICMP and the teardown for the ICMP.
View 6 Replies
View Related
Aug 22, 2011
I´m getting a dynamic public IP from my provider and what I´m trying to do is to establish a remote vpn tunnnel using IPSec which I achieve but every time the sessions resets or the ASA 5505 resets I get a new public IP and I need to put the new IP on the remote client so I can establish the vpn... How can I establish an ipsec vpn using DNS? For this scenario the remote vpn client is a vpn phone but it could be for any vpn client.
Private IP Public IP Private IP
PBX ---- (LAN) ---- ASA 5505 ---( Internet ) --- Remote Site ( Router ) --- (LAN) -- VPN Phone
View 3 Replies
View Related
May 7, 2012
I have a site to site IPSec tunnel setup and operational but periodically the remote site goes down, because of a somewhat reliable internet connection. The only way to get the tunnel to re-establish is to go to the remote site and simply issue a ping from a workstation on the remote network. We were having this same issue with a Cisco PIX 506E but decided to upgrade the hardware and see if that resolve the issue. It ran for well over a year and our assumtions was that the issue was resolved. I was looking in the direction of the security-association lifetime but if we power cycle the unit, I would expect that it would kill the SA but even after power cycling, the VPN does not come up automatically.
View 1 Replies
View Related
Nov 18, 2011
I configured an IPSec VPN tunnel between two ASA 5505 firewalls. I would like to make sure that the IPSec tunnel (hence the security association) is permanent and do not drop due to idle condition.
View 2 Replies
View Related
Jun 29, 2011
I need to route traffic to DMZ (and internal) from the branch office thru the IPSec tunnel. How do I manage that with my Cisco 881?
View 1 Replies
View Related
Mar 29, 2011
I have running more the 30 VPN tunnels on my ASA5540 release 8.3(x).I want to disable one VPN tunnel(temporarily) without removing the configuration either Phase 1 or Phase 2.let me to know the command to disable IPSec VPN tunnel on CLI or ASDM.
View 1 Replies
View Related
Aug 9, 2012
I'm having trouble configuring an ASA5505 on version 8.31 code for an IPSec tunnel. I've done this multiple times on 8.2.5 but can't seem to get my tunnel to even attempt to come up on this ASA. Not sure if it's relevent or not, but this remote ASA has never been used for another VPN tunnel before. When I attempt to ping a host on the other side of my tunnel, I just see the following: 8108# sho crypto isa sa
There are no isakmp sas
My local network is 10.1.1.X/24 and my remote peer network contains 66.37.227.X/24. I've been working on this for the better part of the day and would love to get it resolved.
View 8 Replies
View Related
Aug 3, 2011
I've created an IPSEC VPN site-to-site from a SR520 (remote office) to a Nortel Contivity(home office)...all works really well on the VPN front as I can communicate effectively over the tunnel. However, this setup will be deployed at a few smaller sites and I'd like to setup a split tunnel so that Internet bound traffic goes straight to the Internet while traffic bound for our home office goes over the IPSEC Tunnel.
View 1 Replies
View Related
Apr 23, 2012
We have about 9 1900 routers and 1 ASA 5510 for partail mesh VPN network. So 8 1900 connect to 1 1900 and ASA located in HQ and datacenter. All worked well however there is one site running really strange. The tunnel between 1900 is up for a while and down. Reboot router seems to be the only fix. But tunnel to ASA does not seem to be down at all.
The issue happened again today, we rebooted the router on site but tunnel still not up. DEBUG shows: deleting SA reason "Death by retransmission P1 "
I can see alot of Apr 24 19:57:55.271: ISAKMP:(0): retransmitting phase 1 MM_NO_STATE...
To me it seems like the IDE packet sent but never got reply and timed out. I did also check on the other end, the HQ. All other tunnels are still running fine on that router, just this remote site. Plus I got the similiar output when debugging on HQ router.
One thing do notice though, there was no match on both router for the ACL to match/permit ESP traffic... I asked on-site staff to reboot the modem used in remote site.
View 3 Replies
View Related
Mar 19, 2011
I have a Site to Site IPSEC VPN Tunnel created with ASDM wizard.
Cisco ASA-5505
Peer A: x.x.x.x
Lan A: 192.168.0.0 255.255.255.0
Fortinet FortiGate-50b
Peer B: y.y.y.y
Lan B: 192.168.23.0 255.255.255.0
I start traffic from LAN B with a ping (or telnet it doesn't matter) that receive no reply but tunnel goes up fine.
"show isakmp sa" seems ok (says "State : MM_ACTIVE")
"show ipsec sa" seems ok but all #pkts are zero
try ftp, telnet from LAN B to LAN A systems but no one work. "show ipsec sa" all #pkts are zero As soon as I generate traffic from LAN A to LAN B these works (with tunnel already up) also traffic from LAN B to LAN A works.Obviously if I end VPN and start tunnel making traffic from LAN A all work fine bidirectionally, LAN A reach LAN B and LAN B reach LAN A.No msg logged in either two appliance.
Seems a very strange problem because seems not related to Phase1 or Phase2 already established.Traffic (routing ?) start works only after at least one packet goes from LAN A to LAN B.No msg logged in either two appliance.Problems begun in ASA version 8.0(4) ASDM version 6.1(3) and remain/continue after upgrade to ASA Version 8.4(1) ASDM version 6.4(1).
View 1 Replies
View Related
Aug 3, 2011
I'm having some trouble configuring 2 cisco routers (877) with ipsec vpn tunnel.The 2 of them are linked to the internet with dynamic adsl's - their ip-addresses changes all the time.when the configuration is based on ip addresses it's working ok, but when I'm trying to use host name with the DDNS feature, it's not coming up, I get a lot of errors...
I've searched google and various posts regarding that issue.It's seems like it's possible to do a dynamic-ip to dynamic-ip ipsec tunnel, but I found zero manuals and configuration.I've added the template that I'm using to configure the tunnel with ip addresses.
View 2 Replies
View Related
May 23, 2011
Iam fairly new to Cisco IOS and am having trouble getting an IPSEC tunnel to come up between 2 cisco 881-s. I have entered both debug crypto isakmp and debug crypto verbose but when I try to ping an internal IP at the other location through my VLAN1 interface no debugging info comes up.
Also my ACL-s for the crypto maps show no activity. I have tried many things so my configuration files are starting to get really messy.
[code]...
View 1 Replies
View Related
Jan 30, 2012
We have 7 remote offices and 10 tower locations that utilize IPsec tunnels back to our HQ. We now want to force all traffic including web surfing through the tunnels. What would be the easiest way to acomplish this? I have tried utilizing the crypto map policy to do this, but was unable to acomplish this.
Each of our office locationss utilize a Cisco 2811 router and the tower locations utilize a Cisco 881.
View 21 Replies
View Related
Mar 5, 2012
I'm attempting to debug an ipsec tunnel on an ASA 5510 (8.4(3)) and when I turn on `debug crypto ipsec` and then execute `logging monitor` I get an constant stream of TCP debugging events, is it possible to only view ipsec messages?
View 2 Replies
View Related
Feb 10, 2011
Having a problem getting an ipsec tunnel to work between 2 asa 5505. This in one of the two configs.
Result of the command: "show run"
: Saved:ASA Version 8.3(2) !hostname 20Pullmandomain-name skeincenable password IKxxneNMTRgDw/Xd encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface Vlan1nameif insidesecurity-level 100ip address 172.16.1.70 255.255.255.0 !interface Vlan2nameif outsidesecurity-level 0ip [Code]...
View 1 Replies
View Related
