I am in search of a 1 Gig Ethernet WAN module for 2900, 3900 series router.I want to terminate 230mbps link on this module.I found EHWIC-1GE-SFP-CU option but as per service provider it will not support to 230mbps link.
View 3 Repliesprovide my some (official) info regarding the MBTF for the C2900 and C3900 routers (2911 and 3945)? This info is currently not part of the data sheets.
View 0 Replies View RelatedI faced some problems when updating the device packages on the LMS 3.2 server. Therefore, I really need device packages of switch 3750, router 2900 and router 3900 series. I had tried update online but could't view any devices.
View 1 Replies View RelatedCisco 1900 , 2900 and 3900 have Interface Slots and Service Module Slots , My question is which type of card is support this slot.
View 6 Replies View RelatedWat will be the default memory and hard disk for SM-SRE-710-K9 and wat will be the maximum support for this module.
View 1 Replies View Relatedi have a cisco router (3900 series) and a add on module (4 x 1 Gig port module). For some reason i cant seem to port channel them and cant do routing (can set an ip address on those ports). I can do port channel and routing on on-board ports. Do i have to enable any commands to do this ?
View 3 Replies View RelatedHow to configure a module NM-16ESW because with the command "show diag" and "show int" can not query it.
Note: the default IOS is installed, you will need to upgrade to a specific '.
Trying to set-up a p2p link between a L2 fast ethenet module (within a 2900) to a 6506.Have created a subinterface SVI on the 2900 and put the fast ethernet port in the respective VLAN. However on 6506, am I correct in thinking I can do a no switchport and just create a L3 interface? Do I need to put the 6506 in the same vlan and the fast ethernet module and create a L3 SVI on it? As it's not a trunk port between the 6506 and the fastethernet module, the packets won't be tagged?
View 3 Replies View RelatedIs there a way to configure one of the GigE ports on the E4200 to only work on the "guest" network? Basically I have a need to setup one of those ports to get to the Internet, but I don't want it to be able to get to anything else on the private side.
View 1 Replies View RelatedIf there is a router ISRG2 2900 with SEC license and without HSEC license, there is a limit in count of cumulative encrypted VPN tunnels of 225. Which commands can show us a number of current tunnels on the router, so we can see if we are near this limit of 225?
View 4 Replies View RelatedI am setting up six ISE 3355 appliances 3 in one datacenter 3 in another. They have just installed a new server farm infrastructure using Nexus 5596 and Nexus 2248TP top of rack switches.I have been looking for documentation on how to do NIC teaming on the 3355 or some way to connect Gig0 to FEX101 and Gig1 to FEX102. Or do I just setup a port channel using LaCP between the two different FEX groups?
View 1 Replies View Relatedwhat is the best way to remove configs from ports (GigE or Fa) in a 6500 that we aren't using anymore (i.e. best way to return a port to default). Remove each line one at a time or is there a command to default a port?
View 2 Replies View Relatedwhich models of HP ProCurve or Dell PowerConnect support 64-bit IF-MIB counters, or for that matter any other manufacturer (Zyxel?) (snmpv2 or v3, OID .1.3.6.1.2.1.31.1.1.1.6)I believe pretty much any Cisco Catalyst above a 2950 do, however don't believe any of the SG series do. I realize I could pick up a 2960G for $1500-2k and be good to go, but I forsee a larger switch purchase in the future, but still could use a switch in the meantime that was able to allow accurate monitoring of closet uplink bandwidth?
View 1 Replies View Relatedi have a gateway router going to the internet....using public IP addresses on both interfaces. starting on Monday, traffic would suddenly stop flowing from the inside of the network going out, though i can still ping the outside interface , but when I log in to the router I am able to ping to the internet. so its like traffic is not passing from the outside int to the inside int. I have a 3900 router. other thing is, when i restart the router it will work for some time and then just stop again....
View 6 Replies View RelatedAm trying to do a dynamic configuration of a 3900 series router (3925 to be precise).For the software and licenses, under the IOS technology Package Licenses, what's the significant of SL-39-DATA-K9 and SL-39-SECNPE-K9? Are they really necessary for the router?
View 3 Replies View RelatedI am looking for the procedure of the router 3900 series failover. I have got two 3900 series router with the same ISO and other interface cards. What are the main things that I should watch ? Does the standby router takes the same ip of active router if the active router fails ? How should I configure it.
View 1 Replies View RelatedI would like to configure the policy base routing (PBR) on router (3900) base on the "specific tcp port" (TCP port 16255) to re-direct the traffic to another FE port.
From cisco web portal, CAT 4500 should support PBR as below:"Policies can be based on IP address, port numbers, or protocols. For a simple policy, use any one of these descriptors; for a complicated policy, use all of them." url...
Does 3900 router has the same features on the PBR? if yes, can it support "source tcp port" and/or "destination TCP port"?
I recently upgraded from a Cisco 3900 series router to a Cisco ASR1k router. Since the upgrade, I have internal clients who claim they cannot connect to external VPNs. These internal clients are behind a NAT that routes a public IP address to a group of clients with private IP addresses.
How can I ensure that all VPN traffic is able to pass through the NAT?
Transitioning from 3825 to 3945 (OS is 15.0(1r)M13 c3900-universalk9-mz.SPA.151-4.m4). Turning on FDL on the 3825 was easy but the same command on the 3945 doesn't work.
View 3 Replies View RelatedCan the 3900 series router be ordered or upgraded to a license with advances enterprise services? I have a few of these routers and I'm looking to get the license upgraded if possible.
View 1 Replies View RelatedMy Cisco 3900 router is not taking the no auto summary command?
View 5 Replies View RelatedIs there a router (1900-3900 series router) that will support a 100FX fiber connection. We use to use 2800-3800 and 2600-3700 series routers with FX fiber interface now these routers are no longer available and our need for 100Mbps FX is still a requirement.
View 3 Replies View RelatedI have DSL 8Mbps DL and 768kbps UL The setup look like this:Internet -> Modem -> Cisco Router -> Firewall -> Switch Core - > Multiple switches like sfe2000p? CiscoRouter: i use port gig0/1 for PPPoE and i use port gig0/2 for LAN static Router port gig0/2 with 122.54.144.153/29 connected directly to Firewall port13 with 122.54.144.154/29 ?i want 122.54.144.153/29 will my default gateway ? include no limit bandwidth,filter etc at router, Firewall will be DHCP Server and control the bandwidth, filtering etc and the client computer should get 8Mbps
Mode: Routing
Encapsulation: PPPoE
Username: xx
Password: xx
Service Name: ISP name
[code]....
Any way to disable the usb console port on a 2900 series router?
View 2 Replies View RelatedI configured dmvpn at cisco router 2900. one hub router and 3 spokes. all of them are working normally but tomorrow i see one error at at one spoke router.
error:
Maximum Tx Bandwidth limit of 85000 Kbps reached for Crypto functionality with securityk9 technology package license
I am attempting to set up snmp v3 monitoring of my 2900 series routers from the third party Spiceworks utility. My snmp config on the router looks like this:
SNMP-Server view Westv3View internet included
SNMP-Server group Westv3Group v3 priv Read Westv3View
SNMP-Server user Westv3User Westv3Group v3 auth MD5 <password1> priv DES
[Code]....
I have set the logging level on the 2900 router to informational and see no errors of any kind popping up when I try to scan the router from SpiceWorks. Spiceworks just returns a generic "unable to contact host" message.
I have a Cisco 2921 router running c2900-universalk9-mz.SPA.150-1.M4.bin.Its licensed for ipbase, ipbasek9, Permanent and uc,uck9,Permanent (I'm using the router as a voice gateway),I'm looking to update the IOS to c2900-universalk9-mz.SPA.150-1.M5.bin as I'm told it has a fix for some DSP problems.So the question is, do I need to obtain a new license key to apply this update or am I covered by the existing license on the router.
View 3 Replies View RelatedI have a requirement where 3 Branch locations of an organization is connected to their hub location via MPLS.They have an internet connection only at HUB as shown in the diagram (Attached)Now all spoke locations should access internet via hub.At spoke locations is there a way that I can have Cisco 2900 router and dedicate only 30% of the WAN bandwidth for internet browsing traffic.Remaining 70% should be used for accessing applications at hub.
For example if i have 5 Mbps Mpls port at spoke I want to dedicate only 1 Mbps for internet browsing traffic remaining should be dedicated for accessing the application at hub.How can we acheive this? Can it be done by using PBR and rate limiting?
I have a Cisco router 2900 with firewall, i need to know how can i allow the ping from self zone to outside zone, i trried to create policy from self to outside but i still didn't allow ping or tracert, i get that message when i try to ping from cisco router: "Unrecognized host or address, or protocol not running"
View 3 Replies View RelatedI have a brand new 2901 and I'm trying to work out what licence features I have. The output of show licence shows I have ipbasek9 feature and datak9 as EvalRightToUse feature. Is BGP included in the base feature? What will happen when the datak9 evaluation period expires?
View 1 Replies View RelatedI wanted to get some opinions on the topic above. We are purchasing MPLS services from a large ISP and they offer a managed router option. I will also have a Cisco ISR 2900 at each site running SRST for my voice system. I have some experience with BGP and am not scared at all to support it if need be. That said, I am currently looking at pros and cons of going with a managed router from this company vs managing my own. Actually, I will manage my own regardless and would just plug it into the managed router. My router is perfectly capable of handling the BGP protocol but I am hoping that I can get some opinions from all of you.
View 6 Replies View Relatedhow to configure a router 2900 to support connection from 2 firewall ( Active Standby connections) How can i said the router to send the traffic to the stand by when it go down the active Firewall?I was planning to use a Switch ( layer 2 capacity only) in the middle of the equipments ( between the firewalls and the router) in order to send always the traffic for 1 physical interface from the router side , and manage to route all the internatl traffic to the virtual IP of both Firewalls.Also i dont know yet how to configure a VPN site to site if i have that scheme and some Publics NAT ( Firewall - Switch - Router ), i was planning to configure a NAT in the Router in order to allow the VPN traffic to internal IP of the Firewall but still dont know if it will work.
View 2 Replies View RelatedI have the below configurations done on a 2900 router. [code]I would like to know, if the IP address assigned to dialer1 interface "20.1.2.133" would be listed in "show arp" ?, as it failed to list on our router and I want to know if this is an expected behavior ?
Secondly, does self ping 20.1.2.133 (dialer interface IP) work ? [code]