We have software router vyatta and about 15 branches with cisco 881w and cisco 1941. All branches have 10mbs bandwidth and 3 of them have 50mbs. Link to vyatta has 100mbs bandwidth and situated in datacenter.All branches connect to vyatta via vpn site-to-site with ipsec.I want to change vyatta to cisco router or asa.
View 7 RepliesPoint me in the right direction to determining what Cisco router model will fit in certain situations. I don't want someone to just tell me what I need, I want to be able to determine it for myself.I figure that some of the things that need to to be taken into account are processing power, memory, physical port needs, features available and services going through the router.
View 7 Replies View RelatedI am looking to purchase an ADSL wireless modem router combo which will be mainly used for net browsing, online gaming (ps3) and skype.It has been suggested by the IT tech we use that I a get dual band n wireless gigabit modem/router but my limited knowledge and the confusion created by reading multiple contracting reviews of products is sending me a bit loopy.
View 2 Replies View RelatedI have an EA3500. PPPoE connection. Can't seem to choose my DNS server (use Unblock-US) since the router insistently forces me to use the DNS from ISP.How can i work this around? I'm kinda tired of people asking me why i am changing the DNS. I want to change the DNS and that's final. It's a resource like any other and i want to use it.P.S: i tried most of the basic troubleshooting. I tried my old router back on and the DNS's works fine. I tried even conecting the old router re-routing the new one, and the other router manages the selected DNS's servers fine.
View 9 Replies View RelatedI setup E4200 good. But, in Access Restrictions, there is no policy to choose from. Just Parental controls only.restore the Internet Access Policy like the good old routers?
View 1 Replies View RelatedI have a little experience in LAN management, solving basic connectivity issuesHowever, I am not strong theoretically. Particularly, when it comes to OSI reference model,I feel like I have understood the funda, but at the same time, I get lost, here and there,This is regarding the steps or processes involved, when one PC sends an email to another in a network,When I compose an email and hit enter, this is what I have understood.Each layer, starting from the application layer, passes the data and the control information to the layer below it, until the lowest layer is reached, from where, the actual transmission takes place via the physical medium.What are port numbers? How and when are port numbers chosen? Who takes the decision in choosing them?
View 2 Replies View RelatedI been using 1142n Autonomous several times.Now i have new requirement to setup 12 LAP 1142n, using a WLC.Can suggest what model of WLC should i choose?? About 30 users, in a cargo warehouse invironment.Now it is a good time for me to learn & play around with WLC.What else should i need in order for LAP & WLC to work??
View 7 Replies View RelatedI have been having some connectivity problems and one suggested solution was to upgrade networking firmware. I did this for our router (Cisco RVS4000 v2) and it didn't work, so I moved on to the wireless access points (two WAP4410N). Before doing that, I also reset both to factory default settings - neither would respond to pressing the reset button but it seemed to work using the web interface for both.
Before I did anything to the WAP4410Ns, I noticed they were connected in B/G/N-Mixed mode to channel 6. Now the wireless network mode is stuck on Disable. I can choose B/G/N-Mixed from the dropdown list, but can't choose a channel - the dropdown list for that is empty. And if I try to choose Save after choosing B/G/N-Mixed, it reverts to Disable.
I just spilled water on my companies Dell Latitude D630 and it didn't start. On the D630 I signed onto a domain. When I put the hard drive from the D630 to a Dell D620 the domain option is grayed out. The only option is to log onto locally. Is there anywhere to get the domain option back?
View 8 Replies View RelatedMy Cisco 861 wireless router (CISCO861W-GN-E-K9) don't support EIGRP. What will I do to enable it?
View 1 Replies View RelatedOur LMS DCR include more then 1200 devices, ( ASR 1000, CISCO 2600, 2800 advanced ip services IOS etc. )Everything is working well except the IP SLA device table is empty.I can not choose any device from this table.How can i import/add devices to this table/database automatically ?
View 2 Replies View RelatedI'm going to install a Cisco Aironet 1310g (ap mode) with external antenna in a warehouse (contain many metal surfaces), and I need to install this antennas on ceiling (distance from floor to ceiling is about 13 metres). I need to get at least 1Mbps performance. AP clients are Motorola MC9190-G mobile computers.
View 3 Replies View RelatedI am trying to configure two ASA-5505 as a failover pair. Software 8.2.5 and ASDM 6.4.5.206 Using the wizard i get to step3 .. then nothing happens. Trying direct in asdm but the only interface i can choose is "--None Unnamed-"
View 1 Replies View Relatedchoose the right media converter for my private LAN? My budget is very less & I found TP-Link products fits in my budget.I got confused by looking at 2 models & don't know which one to choose. TP-Link's MC220L and MC210CS. these two models are same but with different I/O Ports(connectors) for Fiber Cable connection?
View 4 Replies View RelatedI need to configure BGP on our 7204 and 2811 router. The 7204 is our main router and currently running EIGRP internally. Our remote locations just moved to an MPLS connectivity and they have a 2811 router. I will need to configure BGP for the routing protocol. I have the AS number and the remote AS number. Attached is the the current configuration of the two routers.
View 4 Replies View RelatedI have setup 15 x RV180W's so far for a particular client.They have requested that we add a Corporate Wireless VLAN for their laptop users (not guests) and add a Special Use WiFi VLAN for a particular mobile platform that is being deployed (in this case we need 2 separate WiFi VLANs to ensure compliance).Also, none of the VLANs can talk to eachother and they have their own subnets.I have the Wireless and VLANs setup, no problem... but I am having an issue wiht the VPN settings.I have the wired network's subnet working fine. But I do not know how to add the subnets for both Wireless VLANs to the traffic selection.The IP schemes will not allow me to just select a large subnet... here are some examples:
Wired VLAN: 10.10.x.y
Corporate WiFi VLAN: 10.15.x.y
Special WiFi VLAN: 10.18.x.y
x is the octet that defines the physical unit location (unit 1 = .23, unit 2 = .24, etc...) y is the octet the host.Since they are not in a contiguous block, I cannot just use a larger subnet mask.I can add multiple traffic selection rules to the ASA5515 at HQ, so that side of the tunnel is perfect... I just don't know how to add the three VLANs to the RV180. Is it as simple as using commas or semicolons?
I have a GM4019e Gateway desktop. I need to buy a somwhat inexpensive wireless adapter, but im unsure of which one will work with my computer.
View 1 Replies View Relateddoes a router Cisco 887 va k9 support EIGRP and IPsec ?
View 2 Replies View RelatedI have a ASA5508 running in 8.3(2) and without enable NAT. If I do a static network address translation for a inside address. any Implict rule in xlate?In another words, what is the forwarding rule ASA choose while there is routing exist and NAT? Do I need to setup bypassing NAT?
View 3 Replies View RelatedIn EIGRP, if a router loses the successor to a route, and it has no FS, it goes active (starts asking all neighbors if they have a successor for that route).But if the neighbor did have a successor, shouldn't they have pro-actively told us about it when they learned it (so we already have it as the Feasible Successor?).
View 6 Replies View RelatedI redistribute our MPLS eBGP routes into our internal EIGRP process at each site. This action undesirably redistributes locally generated BGP networks (via network command) that are meant from the MPLS cloud into our internal routing process.I currently have a route-map on my 'redistribute bgp' command that filters each network manually with an ACL. This works but adds obvious administrative overhead; each WAN router advertises different networks, and the ACL must be updated for each new network.Would it make more sense to simply deny routes from BGP to EIGRP with a metric of 32768? Something like this,route-map deny-local-bgp deny 10 match metric 3276 router -map deny-local-bgp permit 20,router eigrp 100 redistribute bgp 65104 route-map deny-local-bgp.
View 19 Replies View RelatedI have a setup where a router learns a subnet from both EIGRP process and a BGP process (EBGP peer). In the network's normal state, the EBGP path is preffered path (Primary Path). When the route to the subnet is lost in EBGP, then the router will install the EIGRP learn route into the routing table and use that as its path to get to subnet now (Backup path). This works as expected.
The problem is when the EBGP learn route comes back, the Router still holds on the EIGRP learned route in its routing table. I would think that since the Admin Distance (AD) of EIGRP (90) is higher then the EBGP AD (20) that once the EBGP route is learned again, that it would re-install itself back into the routing table (replacing the EIGRP learned route). But this is not happening.
Im not sure what Im missing here since I thought AD was highest considered attribute the routing table consider when install a route learned from 2 routing process.
The setup Im running is an Cisco 7206VXR (NPE-G2) processor (revision A) running IOS c7200p-spservicesk9-mz.124-15.T12.bin.
i have a stack of 3750x, with minimal configuration. there are two vlans, and two vlan interfaces with IP addresses. when i ping out from this switch to another host, it picks vlan1's ip address as the source automatically. i tested this by doing two pings with extended options using each vlan's interface as the source, and got different results. how the switch decided to use the first vlan's ip address as a source.
View 11 Replies View RelatedI am working at a client site today on a routing issue. I am currently working on an issue where a 3750 switch running EIGRP will not update its neighbor router when a network statement is added to the eigrp instance.The neighbor is a 3825 router.
Both the switch and the router have a common network which is 192.168.36.0/24.
Both the switch and the router are in a neighbor adjacency.
Both boxes have "no auto-summ" in the routing configuration instance.
I can run debugs on both routers (debug eigrp packets) and then I can watch queries and updates when I issue "auto-summ" or "no auto-summ". Also I see a "graceful restart" for the peers when this is done.I had an expectation that when I added the network (this is just an arbitrary network for testing, which is 172.16.69.0/24). I wanted to watch this network being sent in an update to the neighbor router.When I add the above mentioned network, there are no updates packets sent from the 3750 to the 3845. I have not had success to this point trying to resolve. I have followed the Cisco document "Troubleshooting EIGRP Flow Chart", but have exhausted all it has to offer and now it is at the point where it is telling me to contact TAC.
I have a pair of data center core 6500 is running a single EIGRP AS with the standard core redundant cross connects. Recently an SVI sub net was expanded from a /24 to a /23 and dropped out of the EIGRP routing table. Subsequent trouble shooting lead to the router id being one using an IP address that is no longer active IP address.
Reviewing old configurations I found, that year ago, the ip address used for the EIGRP router-id (10.100.106.3) was removed from the active interface and changed but the EIGRP router-id was not updated. The switch has not been rebooted since, no loop back is configured and there is not a higher IP configured on an active interface. Reviewing documented material on it, I cannot find anything specific on this condition but do see in the discussions on duplicate IDs, that new route updates can be a problem. I know how to update the router id but I am looking for confirmation on what would be the impact when I add a new loop back and manually configure the router-id under the EIGRP process with the new loop back IP.
My assumption is an EIGRP update and route re convergence with the standard 90 seconds of outage. How to confirm this is assumption is correct? I have no test bed to find out myself without doing this on the active cores.
show version Cisco IOS Software, s72033_rp Software (s72033_rp-IPSERVICESK9_WAN-M), Version 12.2(33)SXI5, RELEASE SOFTWARE (fc2) show inventory NAME: "WS-C6504-E", DESCR: "Cisco Systems Cisco 6500 4-slot Chassis System"PID: WS-C6504-E VID: V01, SN: <deleted> NAME: "1", DESCR: "WS-SUP720-3B 2 ports Supervisor Engine 720 Rev. 5.3"
PID: WS-SUP720-3B
EIGRP configuration is pretty basic:
router eigrp 10
network 10.0.0.0
redistribute static
passive-interface Vlan110
passive-interface Vlan80
[code]...
We bought a CISCO1941 K9 router. To enabled IPSec feature, I need the PAK to active IPSec on 1941. Where I can buy a valid PAK? Could it be done via on-line support?
View 5 Replies View RelatedI have got a Cisco 1941 router and would like to activate my SSL VPN license on it. How do i go about it?
View 6 Replies View RelatedWhat is the processor available in cisco 1941 router? is it RISC?
View 4 Replies View RelatedHow do i configure SSL VPN on a Cisco 1941 router? I would very much want a howto guide that does step by step. I have not found one my self so far.
View 1 Replies View RelatedWe purchased this router with the cisco IOS software installed. I've installed the Vista driver on my win 7 box. I believe that should work. I installed Putty to termainl in and I'm using a USB connection. I cannot even log into the router. I thought I was going to see some kind of setup wizard using the CISCO software so I would use a GUI and get things moving. I've got loads of reference material with command etc. but I just can't connect to the router to make it happen.
View 3 Replies View RelatedI need to unlock IPSec to my 1941 router but I'm not sure which license(s) to purchase.
View 1 Replies View Relatedi have cisco 1941 router.unfortunately i dont remember password.Can any body tell me how to break password.I tried to go in Rom mon using ctr+break but nothing is happened.
View 5 Replies View Relatedc1900-universalk9-mz.150-1.M4.3
-------------------------------------------------
Device# PID SN
-------------------------------------------------
*0 CISCO1941/K9 FCZ1510C50V
Technology Package License Information for Module:'c1900'
----------------------------------------------------------------
Technology Technology-package Technology-package
Current Type Next reboot
[code].....