Cisco WAN :: 2651XM - NAT Feature Set / Can IP-BASE Be Used On Router
Apr 17, 2012
I have Cisco 2651XM and currently running old IOS c2600-is-mz.123-26.bin (IP PLUS) which I used the NAT protocol. I was wondering can I use IP-BASE on this router and I am not sure if this feature set has NAT protocol.
I have been looking to find out the list of features that the IP Base IOS has for the 3750X series switch. What would be ideal is a comparable list but essentially I need to know which of the LAN Base/IP Base/IP Services has SSH functionality.
Full feature set for IP Base with the 3750x.I just wanted to verify that I could create a routed port, turn ip routing on, and create static routes as well as a default route. From what I can find, there shouldn't be a problem with this on the IP Base Feature Set, I just wanted to verify. Or any link for the Features of IP Base on the 3750x.
The model WS-C3750X-24T-L is only Lan Base. We need this switch to use EIGRP Protocol. Does it exist a License for supportting IP Base o IP Services Feature Set?
cisco 2561xm router with WIC1-adsl card and NM-16ESW switchIOS: c2600-ipbasek9-mz.124-23.bin ,I recently had to temporarily disconnect my above router for a few days and replace it with a cheap plastic home router and was embarrased to discover my adsl broadband speed shot up 45% with the cheap router. With the cisco 2651XM I always got a max download of 400kb/sec but with the cheap router I was getting 580kb/sec. Clearly something is wrong with my cisco config, I put this down to the mtu setting, which in the cheap router wasn't shown but set to auto. I've tried different mtu settings in the cisco router (including 'no mtu' but never get more than 400Kb/sec.My isp indicates optimum mtu is 1500 but that doesn't produce any speed increase.What can I do here to get the cisco router working to maximum speed?
I have a cisco 2651xm router here at home, and at another remote location I have a cisco 1760 router, both are connected to the internet via adsl (WIC1-ADSL card).The problem is that from home I can't connect to the snmp-service on the 1760 router. I'm using a PC that's on the LAN of the 2651XM router, the blockage is in the 2651XM router, because if I swap it for a cheap plastic domestic router I can get snmp data from the 1760 router, and this is without any port forwarding in the domestic router. What config do I need on the 2651XM router so it will pass this traffic?
I have a 16 port hub (NM-16ESW) installed in this router. Is there a way to lock down this hub so that only whitelisted machines will be allowed to connect to its ports? ie: by mac address or some other type of permission method? How to be able to plug their computer into the hub and join the network unless their device has been ok'd first.
I have a WS-C3750X-12S-S (IP Services) that I THINK I'd like to downgrade to LAN Base so I can stack it with a WS-C3750X-48T-L that is already LAN Base..
Can a 2651XM router be configured as a PPTP VPN endpoint (client)? I ask because I want to connect this router to a professional vpn (privacy) service such as proxpn or mullvad or similar. If it can't, any vpn privacy services that cater for cisco-based vpn connection?
We have a number of 2651XM with WIC-1ADSL. These are supplied by another company and we do not have access to the configs.We are told that the maximum througput from the ADSL WIC to the FastEthernet 0/1 is 2.5Mbps ( "it's a backplane issue" ), even though the ADSL speed reported by the router on the external interface is 8MbpsT
if I do #sh arp in the terminal with this router I see a rogue entry thus: Internet 192.168.0.4 0 Incomplete ARPA
My whole LAN operates on 172.16.x.x/16, there are no 192.168.x.x devices connected. In the past I've had 192.x.x.x devices running but for a long time and the router has been restarted since then. I've tried several clear commands in the terminal but this entry is stuck there and I've also seen it in a wireshark scroll on a pc when monitoring the routers' adsl traffic - it shows up an an SNMP entry and I do use SNMP on my router, but that data goes to a 172.16.x.x. machine. How can I clean this entry out?
We have a Cisco 2651XM at the edge of our network, which routes our public IP block. This sits on a 100 Mbit/s ethernet pipe (full duplex) up in the datacenter. We are also running 100mb full duplex on our our side of the network. We have several public servers behind the router.
We have recently set-up a new Apple OS X Lion Server to serve a few websites. However, when downloading some files from the server the from a remote location, I noticed I can only get a maximum of 15 Mbit/s out of the connection.
When downloading a large file over HTTP (Apache) from this OS X Lion server from another server on the same internal network (behind the router), we get a full 100 Mbit/s transfer speed.
However, when we download the same file from anywhere on the internet (external side of the router), we can only manage to get 15 Mbit/s out of the transfer.
However, we also have other Linux & Windows servers that we can achieve a full 50 Mbit/s (our office connection speed) externally under the same network conditions.
So it also appears it's only for a single connection - not a limitation for the whole server. If I open two HTTP connections, I can get say 15 Mbit/s out of each transfer - totalling 30 Mbit/s... if that makes sense.
Update: I also notice slower ping latency when pinging from outside the network. Most of the servers reply in 15ms while the new OS X server usually takes over 40ms on average.
Router show ver: Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-IS-M), Version 12.2(11)YT2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
cisco 2651XM router with WIC1 adsl card and NM-16ESW switch IOS: c2600-ipbasek9-mz.124-23.bin
I use the following config to export traffic from the adsl card to a fasterthernet port so I can look at the adsl traffic in wireshark on a pc:router(config)#ip traffic-export profile my_rite router(conf-rite)#int FastEthernet 0/0 router(conf-rite)#bidirectional router(conf-rite)#mac-address abcd.efgh.ijkl (mac address of PC) router(conf-rite)#exit router(config)#int dialer0 router(config-if)#ip traffic-export apply my_rite this config works and I can see stuff going on in wireshark but it's only one way. This config only shows traffic going out from my adsl card, but no incoming. There is defintely traffic going both ways because everything about my adsl connection is working perfectly. I've tried using a different fastethernet port, even tried exporting to a different pc but all I see is outgoing ie: source is my public ip address but never as destination . I have bidirectional in the config but it still only shows outgoing. I even tried a different IOS (c2600-adventerprisek9-mz.124-15.T8.bin) but still it doesn't show incoming traffic. Could it be my ISP in some way hiding incoming traffic from view?
I need to diable RDP packet inspection on this router but I can't find where I do that. I'm having troubele with audio on a sip line and I read here (bottom of page) url...that turning off RDP packet solved the problem. I've looked through the config and searched on google but couldn't find the asnwer. what is the command to turn off RDP packet inspection?
our WAN is connected via L2WAN and using EIGRP to connect the sites. Currently there are 35 EIGRP neighbors over L2WAN and we are to install 15 more sites and will be connected to the same L2WAN. Some sites are still using Cisco 2651XM and we would like to know if it can still handle another 15 EIGRP neighbors. Some sites are 2800 and 2900 routers. And is there any other things to consider for EIGRP over L2WAN?
I 'm trying to set up a home lab with a couple of 28XX and 2651XM series routers.I would like to simulate a frame-relay connection between HQ, Branch1 and Branch2 . All of them are conneced to a PSTN switch (2811 router) via T1 cross over cables. The connectivity is like this. [code] I have configured all the routers and FR switch with necessary configuration. However the link between HQ and Branch1 is not coming up. On both the routers I could see the line protocol is down.I have pasted the configuration below.[code]
im unable to create pri-group under T1 controllers in 2651xm , I have 3 T1 VWIC controller cards [dual port], tried using differnt IOS [advance enterprise/IPVoice/SPservices], i can onyl see channel-group unter the controllers.
I was wondering if i can enable url filtering on my 2691 or 2651XM routers so that if someone visits any website i can see that under router logs. right now i am using kiwi syslog that logs the router activities.
Need basic wireless configuration for a SOHO Cisco 1811W router? I just need the wireless to connect to the base wired LAN - with both WEP and MAC authentication. And - can the MAC auth. parameters be configured via CLI and not have to use either SDM or CP? I can access the router via SDM - but the Wirless Application will not fire up - and CP doesn't work at all.
First I'm sharing a network via bridging from my dads house. Everything works perfect. I'm using a router at my house with no problems. At his house he as a modem hooked to net gear router and the acer will not connect to internet via wifi. So I bring the thing up to my house and it connects fine via wifi. The acer will connect using a eithernet cable at his house but not wifi.
I was wondering if the acer is getting confused cause his router is hooked to a modem?I've tested and tryed everything under the sun and nothing seems to work.I know theres nothing wrong with the wifi software or hard ware in the acer cause it connects fine And surfs the web via wifi at my house but not at my dads.
I was wondering if it is at all possible to set up a DIR-655 as a wireless base station for any router (specifically a netgear wrg614 v10). I've read that the DIR-655 can be set up as an access point, but with my current situation it's not currently possible.If this is not compatible with this specific netgear router, is there any other solution besides having to purchase a dedicated access point?
I got a simple office: one flat LAN, one single 1841 router and 2 ISPs.LAN is 10.10.20.0/24 and is connected to a port on an HWIC card I installed in the 1841. Then FA0/0 connects to ISP1 and FA0/1 connects to ISP2.
Everything is fine except that I am having some issues with the Failover feature. Currently, I am using Object Tracking with SLAs. I am pinging 2 hosts located on the internet and then I have an SLA OR statement which basically say if ANY of the 2 objects are unreachable, DO NOT trigger a failover to ISP2. If in the case that BOTH objects become unreachable, then DO trigger a failover. It works like a charm.
The problems:Any internet hiccup obviously makes the router activate the tracks and redirects all traffic to ISP2. However, 99% of the time ISP1 is back online within minutes or seconds, so after 180 seconds the traffic gets redirected back to ISP1. So in essence, the customer suffers 2 interruptions.
Besides internet hiccups, I have also noticed that every time any user tries to copy a big file accross the tunnel (the 1841 has site to site tunnels with 2 branches) the tracks go crazy and the objects become unreachable so a failover is triggered. We were breaking our heads and fighting with the ISP1 provider because every time this happened, we called them but every time they kept telling us that their line was UP and running without any problems. So after careful investigation, I do admit they were right.... it is not so much that the ISP1 experiences hiccups, it is actually the fact that users putting heavy load into the router are causing it to have its track to stop reaching the objects.
I have a LAN with multiple VLANs connected through Catalyst 3750 with IP Base image. In IP Base the router only supports PIM stub multicast (no PIM multicast routing),But I have an ASA connected to the internal router and to the internet router.Asa supports PIM multicast routing and can act as PIM RP. With this configuration, is there a way to configure an internal multicast network? That is a multicast server in one internal vlan (VLAN 1) and multicast clients in VLAN 2. Both VLANs connected to the C3750 router.
We have purchased a number of 2911 routers.We got Base & security license as we wanted to enable encryption. However we probably wont use the security.We are replacing 2811 routers.Unfortunately the 2811 routers have FXS ports with 2 - 4 POTS handsets - I completely forgot about these ports when I was ordering.Now I have VIC3-FXS cards which are ok in the 2911 but unfortunately I cant get them to work.I am missing PVDMs (well adapters anyway), and even if I got them the router wont take any commands relating to voice due to the license.Is is possible to 'rehost' the security and turn it into a UC ?I am new to these 2911 and Licensing.
I'm just wondering if there is any documentation that confirms if the 2 built-in Gigabit ports on a Cisco 2851 router support (or otherwise) auto-mdix.I can find information for the modules but not the 2 built-in ports.
Me to a 2951 router with fireawall featureset. Ive begun to move the ACLs that where in the pix. However some of the rules are allowed to be typed in bur when i look at the ACL afterwards they are not what i typed in.
I have a 2911 router with 15.1(4) Ios Version. I need to enable the evaluation sna feature but when I try to enter the command "license feature snasw" but I get an error, the command "License feature" does not exist.
Cisco Router 2851 connected with one ISP using 2 serials. the case is :
1)s0/0/1.1 is the only utilized and s0/0/0.1 utilization is zero. 2)when shutting down s0/0/1.1 : the other ,not utalized, link work perfect and forward all the traffic.
Attached the configuration file with output of show interfaces command.
I have an E900 connected to my LAN acting as a wireless access point (router functions disabled). Can I use the DDNS feature of the router in this configuration? I attempt and get ‘No Internet Connection’.