Cisco WAN :: 2801 Router With Cellular Card
Mar 7, 2011
I have a 2801 router with a HWIC-3G-cdma card that I have inherited from a predicessor. How to use a cellular card on a router and need to get this thing up and running. Any example config that I can see or point me in the right dorection to get this up and running? I have the cellular card set up as Cellular0/1/0 on the interface, I assume that that was done by default, and it has an IP address. The Static Route of 0.0.0.0 0.0.0.0 Cellular0/1/0, in the config with only 2 other interfaces as being direct connection. But that is as far as I recognize. Do I need to set up a router protocol? Which one? How do I use the cellular card? Do I need to have an ISP connection?
View 1 Replies
ADVERTISEMENT
Feb 29, 2012
I am working at a client site today. This specific client has decided to replace their legacy 2600 branch office routers with newer 1921 ISR G2 routers as they move from a Legacy Frame WAN to a MPLS network with a different provider.
The backup in the former scenario was actually an ISDN solution. Moving forward, the provider has sold them a 3G backup solution. To support this, we have purchased Cisco line cards for the 3G. The part number for the cards is "EHWIC-3G-EVDO-V=".
I was asked by the client this morning if there was a way to tell what the IMEI number for the 3G card was. I performed a shew inventory, as well as a shew hardware, but I do not see this IMEI number. I also checked the label on the packaging box that the cards came in, but do not see this number. Is there a way to tell what this number is for each card?
View 20 Replies
View Related
Sep 26, 2011
I got a Cisco C880 router( IOS version: 15.1(2)T1 ) with PCEX-3G-HSPA-G card installed When I insert my 3G card and issue show cellular 0 network, I found that the network is not my 3G card ISP, may i ask how can I manual select the ISP?
View 1 Replies
View Related
Mar 15, 2012
I have this 2801 in a critical environment. We had a brief power blip, and even though the router is on UPS, something happened. Anyway, after working with TAC, they determined the flash card had gone corrupt. Lucky for me I had a spare 2801 in my office, I grabbed that flash card and plugged it in and we're back up and going.
TAC sent me a new flash card. No matter what I do, I cannot get IOS to load on this thing! I am stuck in rommon. Here's what I've tried:
tftpdnld in rommon, times out. using another 2801 as a tftp-server. doesn't complete. using xmodem. ugh. never seems to get started. booting the router with a known good flash card, so I can get to ena, and "copy tftp flash".
have used tftpd32, Solar Winds TFTP server, What's Up Gold TFTP server, and open source tftp from sourceforge. With the tftp32, it always gets to exactly 73% download and then times out (it says, I have a feeling it's noty really a timeout). I have tried having the router and tftp server the only devices on a switch, i have tried the router plugged directly into the tftp server with a cross connect cable. No happiness. The open source tftp server reported (and I have to paraphrase, I am not near the router) "client does not support block number recount" or something like that. The client being the 2801.
The iOS file is about 45M. Someone asked me if the flash card was formatted...would that matter? would the tftp even start if it wasn't?
OK, I've gone on long enough. TAC is dispatching a new card AND 2801!
View 1 Replies
View Related
Nov 2, 2011
I have three routers 811 (independent), and the interface cellular 0 resets in all three.
View 3 Replies
View Related
Apr 10, 2012
I operate a network of sites for a state air monitoring program. One site has two trailers that were previously connected with a wireless ethernet bridge. I installed a cellular router to give them internet access, and they were both able to utilize the connection through the LAN. The ethernet bridge recently went down, and I tried replacing it with a standard wireless router and wireless adapter I purchased from Staples (I needed something right away). When I linked the two trailers with a wireless network connection, it disconnected the LAN and I was unable to access the internet. Is it possible to do this? I'm assuming a wireless ethernet bridge would be better, and also the cellular router does not have a wireless function on it, or I would assume that would be best?
View 3 Replies
View Related
Apr 28, 2011
I'm having extreme issues in getting my vpn client to connect to a cisco router with a hwic-3g-hspa cellular interface
I have tested the config remotely by traversing the tunnel I have setup with a cisco vpn client and the client does connect, however when out on the road it doesn't respond, I'm litterally hitting my head against a brick here, everything just seem right I can't explain it.
I have done debugs and there is no sign of life, its as though when the vpn client connects to the router its not responding any way here is my config for the vpn clients part that is.
aaa new-model
!
!
aaa group server radius vpn-client-server-group-1
[Code].....
View 2 Replies
View Related
Jan 9, 2011
The 1941 router has USB ports, Will it support a USB celluar data card?
View 5 Replies
View Related
Apr 16, 2012
I have a Cisco 819G WAN Router with the following specifications:
Router3G#show inventory
NAME: "C819G+7-K9 chassis", DESCR: "C819G+7-K9 chassis"
PID: C819G+7-K9 , VID: V01 , SN: xxxxxxxxxxx
[Code].....
View 4 Replies
View Related
Jan 25, 2013
I've been able to activate and configure the Cisco 819 router to connect to Verizon via interface Cellular 0 but when I connect a laptop to the router, int Cell 0 goes down.
Here's a snippet of what happens after I connect a laptop:
rt1#ping 8.8.8.8
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 8.8.8.8, timeout is 2 seconds:
[Code].....
View 0 Replies
View Related
Nov 11, 2012
I have a Sprint USB cellular modem 3G/4G. Are there any devices that will let me plug the cellular modem and use it as a hotspot without a computer?
View 4 Replies
View Related
Apr 25, 2013
We're seeing a strange issue with a Cisco 819 that we're testing out. We are able to ping out over the Cellular interface just fine, but as soon as we plug a device into one of the FastEthernet ports we immediately drop the cell connection. The Cell interface then continues to bounce until we unplug the device. We are intending to setup a VPN tunnel, but we've even stripped all that out for the sake of troubleshooting.
Current configuration : 2832 bytes
!
version 15.2
[Code].....
View 1 Replies
View Related
Apr 24, 2013
The tunnel connection is establishing correctly but when i change the priority in he hsrp configuration of my gig 0.1 interface to be the active on this router the cellular 0/0/0 interface goes down, by the way this is going to be my redundancy.
Code...
View 1 Replies
View Related
Jun 3, 2013
I have an issue regarding using cellular interface on cisco 881G. The 3G module is Aircard 504. SIMcard is working on other devices, it have obtain IP address from mobile operator. But on cisco881G it doesnt work.
Here is config:
cellular 0 gsm profile create 1 m2m
chat-script 3G "" "ATDT*98*4#" TIMEOUT 30 CONNECT
interface Cellular0
[Code].....
View 4 Replies
View Related
Jul 23, 2007
I looked but could not find any information on what's the use of the USB interface on my 2801 router. I saw something about Cisco USB memory module and eToken by Aladdin. Is this interface restricted to Cisco and Aladdin only?
View 17 Replies
View Related
Aug 4, 2011
I have a Cisco RV110W small business router setup at my home. It has one of those HTML GUI interfaces, check the boxes, etc.., to get things working. Basically, your typical home router with VPN. I have enabled the VPN, it's PPTP, added the password, and now it's automagically configured! I can successfully VPN to my home with a Windows7 client. Here's my problem, I now need to VPN into my home router with a 2801. Is this possible? Everything I found on the subject has only been to setup a Cisco IOS router as a VPN server or tunneling to another IOS router. No examples using an IOS based router as the client.
View 3 Replies
View Related
May 29, 2012
We have one Router Cisco 2801 at the customer site and facing issue of having very High CPU coming to 99%.CPU utilization for five seconds: 99%/28%; one minute: 99%; five minutes: 98%
View 2 Replies
View Related
Jun 5, 2012
I have a Cisco 881G with PCEX-HSPA-3G card for which I have successfully configured for internet. As the above one has come to end of life, we got the replacement 881G with embedded 3G modem.
I can't get Cellular 0 to use ppp encapsulation:
Router(config-if)#encapsulation ppp
Cellular0: Only SLIP encapsulation supported
Router(config-if)#
[Code].....
View 9 Replies
View Related
Apr 6, 2010
I have problem with HWIC-3G-GSM configuration. The cellular interface doesn't get IP from ISP.The configured profile is always inactive.cellular 0/2/0 gsm profile create 1 m2m.plusgsm.pl chap plusgsm plusgsm
View 3 Replies
View Related
Jan 6, 2012
Can Cisco 881G cellular interface (Modem Firmware Version = K2_0_7_19AP C:/WS/FW) work with r-uim cards? I can't find correct answer in documentation .
View 2 Replies
View Related
Jan 2, 2013
We have a ASA 5505 setup with VPN and using Cisco client 5.0. The VPN works without a problem if we use normal internet access (from home, motel, etc). However if we use a cellular wi-fi hotspot or tether a phone it will connect to the vpn but will not allow us to get on the office network
View 1 Replies
View Related
Jan 22, 2013
I would like to configure the 881G to use both the cellular interface and Fe4 WAN port for internet connectivity.Interface Fe4 is connected to an ADSL router.
I have configure each interface with a default route and weighting:
ip route 0.0.0.0 0.0.0.0 Dialer0 200
ip route 0.0.0.0 0.0.0.0 FastEthernet 4 100
I need to configure Fe4 to get an address as a DHCP client:
interface FastEthernet4
ip address dhcp
no shut
duplex auto
speed auto
How do I remove Fe4 from VLAN1? There is some existing config around VLAN 1:
interface Vlan1
ip address 10.73.0.1 255.255.255.0
ip helper-address 192.168.140.13
ip tcp adjust-mss 1400
no autostate
ip sla 100
icmp-echo 10.64.4.15 source-interface Vlan1
tag 3G Keepalive
frequency 10
Then I guess I need to adjust my Internet-IN ACL to allow broadcasts and UDP 67 and 68?
View 1 Replies
View Related
May 31, 2011
I'm having trouble setting up a Cisco 2801 as an internet router between our firewall & our ISP.I've setup FastEthernet0/0 as the WAN port & FastEthernet0/1 as the LAN port. I've setup a default gateway pointing the next hop (the ISP),when I plug in a pair of laptops configured to mimic our IP scheme, I'm able to ping thru, but when I put the router between our firewall & ISP I'm not able to get out to the internet (can't ping google) I can still ping the next hop.,Our old router died, so I am unable to pull up its configuration. Here is the code I'm come up with so far.
View 6 Replies
View Related
Dec 26, 2012
I need some clarification if it is possible to do an IPL connection between Cisco 2801 (T1) to Cisco 1841 (E1) via Ethernet (2801) to Serial (1841).
I am unable to find any documentation about this and I need to connect our network to an offshore network.
View 2 Replies
View Related
Jan 27, 2013
I have to configure failover on both router. if one get fail then the other router should be dial.Physical connection
•1. Two routers (Cisco 2801) are connecting with splitter through RJ 11 port.
•2.Only one ISP link is coming in splitter.
Requirement: As per as customer requirement. He wants redundancy with in both 2 routers. If one goes down then the other router come up. And same configuration on 2801_R2 router. I am planing to do HSRP on our lan network (2801R1,2801R2 ehternet interface which connected to switch). from switch i will create two default route with (next hope) virtual ip address.
View 6 Replies
View Related
Mar 20, 2012
I have just received Time Warner Cable and get 16Mbps down from them directly through their modem (motorola DOCSIS 2.0 modem- SB5101) to my PC (using speedtest.net). When I then connect TWC's modem through my 2801 router on fa0/0, the download rate I get is considerably slower (on the order of 3-4Mbps via same testing method). What am I missing?
Here is how the passthrough interface is setup:
interface FastEthernet0/0
bandwidth receive inherit
ip address dhcp
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
I have attempted removing bandwidth command - nothing changed with it not there. I have also hard coded the speed and duplex to 100/full to no avail....
Other possible relevant configs:
ip nat inside source list 1 interface FastEthernet0/0 overload
ip route 0.0.0.0 0.0.0.0 dhcp
access-list 1 permit 192.168.1.0 0.0.0.255
Basically this things is wide open... for testing but the download speed differential is perplexing to me.
View 10 Replies
View Related
Dec 26, 2012
I need some clarification if it is possible to do an IPL connection between Cisco 2801 (T1) to Cisco 1841 (E1) via Ethernet (2801) to Serial (1841).
I am unable to find any documentation about this and I need to connect our network to our overseas office.
Our side uses the 1841 router and our provider has set-up our E1 connection to be via Serial interface while on our overseas office uses the 2801 and will connect via the T1 card, which by the way does not have any serial interface ports just ethernets.
So far checking on how to configure this, I am unsure on how the connection will happen since the info that I got is that T1 does not have the option to hold an IP address (also unsure on this though). With this in mind and that the 2801 does not have serial interfaces, does that mean that IPL connection would be via the available Ethernet ports?
View 11 Replies
View Related
Apr 9, 2013
I want to block access of some clients from the vlan1 to acces internet blocking their MAC address. How can i do this?
I have tring this way:
access-list 700 deny mac address 0000.0000.0000
access-list 700 permit 0000.0000.0000 ffff.ffff.ffff
int fa00
bridge-group 1 {input-address-list 700 output-address-list 700}
but it's not working .
View 1 Replies
View Related
May 10, 2011
I have 5 routers. Four routers are: c2801-IPBASEK9-m v 12.4(24)T2. One router is a C2800-IPBASEK9-M v 12.4(24)T3. so, it appears that the IOS on all 5 routers is very similar, the only difference is the T3 at the end of the version and that 4 are 2801s and one is a 2800. What is very wierd is the 4 2801 have the embedded scripting language "tclsh". The 2800 does not have tclsh. If I issue the command: tclsh on the 2800, I get:
Center-GW#tclshTranslating "tclsh"
% Bad IP address or host name% Unknown command or computer name, or unable to find computer addressCenter-GW#
View 1 Replies
View Related
Apr 12, 2011
I have problems with the Router 2801.When i give the command show processes cpu, the command show me that the router is working in 98%.
I have vlans like voice vlan and others, I have one 20 Mb Wan Link and I redirect all traffic from my lan to this link and when i browse in internet or i do downloads the router goes to 98%, when i don't make it the router processes goes down.
I thought be problem with hardware, but i exchange to another router and the same problem happened.Before this situation, I had one link with 12 Mb and nothing happened, when i exchange this to the 20 mb link the problems starting.
View 3 Replies
View Related
Feb 7, 2012
I have one problem doing a ping to a router lan interface, I have 3 routers (2801) connected between each other (separated 1 mile each), the link is established trough microwave signals (connected to the 2801 fast ethernet interfaces), every router has a connection to a LAN. One of them is located at headquarters.Last thursday I replace one of the router with a cisco 2901, i configure the router with the same configuration that was on the 2801, i power up the router and the 2 link were up without problems.One day after the noc called me to tell me that after i replace the router they can't ping the router IP lan interface on the new 2901 (before the replacement the ping was sucessful). I called one user the lan connected to that 2901, and they can do a ping to the router's LAN IP address.
I can ping the 2901 IP wan interfaces, I can ping the LAN users ip address, but i cannot ping the router LAN IP address, from my desktop, and neither the 2 routers 2801 connected to the 2901.I show the configuration on the 2901, I couldn't change it because i didn't have time to do that, but i'll change the configuration to use ipsec tunnels.The configuration as you can see, has a crypto map, but the acl used by the crypto map, only permits the interfaces ip address, so i think that doesn't work, so the traffic doesn't get encrypted, but i don't know if that is the problem why i can't do a ping to the lan interface. [code]
View 5 Replies
View Related
Jan 21, 2013
how to setup a cellular internet sharing?
I'm using 'Cisco Linksys WRT160Nv3' router. Here is my PowerPoint-drawn diagram if you want to know how I want it to work...
View 2 Replies
View Related
Feb 28, 2012
I'm using for a company network a 2801 Cisco Router. This router has 2 FastEthernet Interfaces connected on 2 ISP's and one VLAN for internal users. What acl should i use if for example one client from the lan is using a torrent client to download from the internet. I want just to specify a maximum download speed or to block that client to access the internet when it's trying to download something that can affect other clients from the LAN.
View 2 Replies
View Related
