I have cisco 2911 with IOS-universalK9 mz.SPA.150.1.T, but that does not accept the ip sla monitor commands XX, XX or rtr ip sla XX. How active these commands in IOS or what you belong to?
View 1 RepliesThere are no commands like route-map & ip sla monitor on my cisco 1841 router, its ios version is 12.4(T1). I have to configure load balancing and failover on this router but without these commands i cant do that.
View 3 Replies View RelatedI've got two routers, Cisco 2911's with 15.1(4)M1 on one and 15.0(1)M5 on another.
I'm trying to set up ip sla for vrrp tracking but the commands seem gimped? I don't even have an option for ip sla <operation number>. All I've got is ip sla responder/server/key-chain.
I have a cisco 2911 router that is located in my head office LAN and I use this router to connect to my branch networks. I want to configure IP SLA Monitor on this router to track my WAN Links but it does not support the command IP SLA Monitor. My IOS VERSION is c2900-universalk9-mz.SPA.151-2.T1.bin. how I can configure IP SLA on my router.
View 4 Replies View RelatedI am trying to set up a SLA statement on an ASA 5505 version 8.2(5). When I enter the command "sla monitor schedule 1 life forever start-time now" I get a message stating "%Entry not configured."
View 1 Replies View RelatedI have an old 2621xm router in CCIE lab at home. Only a week ago I started having issue on 2 of them. The problem is on one of them when I go under interface configuration and I type "no shut" nothing happens. Interface stays in administratively down status and when I check running config "shutdown" is still under interface.
On the other one the same problem but only with "router rip" command. I configure my rip routing but then when I check running config there is no rip section and also RIP is not running under "show ip protocols rip".These routers are connected to 2511 AccesServer. So I thought the issue might be communication from AccessServer to these devices. I connected a console cable straight to them and still the same problem. Everything else is working on these devices.
I have a Cisco 2811 router and i want to experiment on the IOS firewall.The thing is, none of the commands that are proposed in online guides - like ip inspect, ip audit, etc. - seem to be working. I just get "unrecognized command" on a router that is supposed to support such features. I'm wondering if it has something to do with the IOS image.
My show version output is this:
Cisco IOS Software, 2800 Software (C2800NM-SPSERVICESK9-M), Version 12.3(11)T9, RELEASE SOFTWARE (fc3)
Technical Support: [URL]
Copyright (c) 1986-2005 by Cisco Systems, Inc.
Compiled Tue 13-Dec-05 08:24 by ccai
[code]....
I've setup and configured the following local monitor session on a 7606 but it doesnt seem to be outputing anything. Any guess as to why, or what I might be doing wrong? Gi1/1 is doing ~40Mb/s egress & 15Mb/s ingress. Both source and destination ports are routed ports.
monitor session 10 source interface Gi1/1
monitor session 10 destination interface Gi1/10 ingress
interface GigabitEthernet1/1
description WAN Link to ********************* ** CORE BACKBONE **
mtu 9000
ip address ************** 255.255.255.252
[code].....
the Dlink Network Monitoring widget just shows: IP Address error?I'm on DIR-655 Rev_B hardware and 2.01 firmware.
View 1 Replies View RelatedBelkin Setup / Router monitor application has stopped working. A problem caused the program to stop working correctly. Windows will close the program and notify you if a solution is available.
View 1 Replies View RelatedMy Belkin N150 wireless router monitor has stopped working. A problem caused the program to stop working correctly. Windows will close the program and notify you us a solution is available.I can not figure out why my wireless router doesn't work sometimes.I need to be able to access this to get to the router settings. I don't know if my wireless is being highjacked or what.
View 2 Replies View RelatedI have configured my CIsco 2911 router and there seems to be something wrong with my configuration regarding subinterface 0/0.102 The hosts on this subnetwork cant access the Internet and i cant spot the error.
Here is my running config on this matter.
class-map type inspect match-any LAN_TO_WAN
match access-group name LAN_TO_WAN
class-map type inspect match-any WAN_TO_LAN
match access-group name WAN_TO_LAN
class-map type inspect match-any GRE_TO_WAN
match access-group name GRE_TO_WAN
class-map type inspect match-any WAN_TO_GRE
[code]....
I am having one router CISCO2911/K9 (Cisco 2911 w/3 GE,4 EHWIC,2 DSP,1 SM,256MB CF,512MB DRAM,IPB). But now my management asking me to upgrade this router as CISCO2911-SEC/K9.
What will be the BOM for this up gradation.
In studying and testing SSL VPN on an ASA I have the network as shown in the attached diagram. The configuration is based on an ASA with 8.3 but our ASA is 8.2 and at this time I'm not familiar with the new NAT configuration and commands in 8.3 or later and how to translate the 'nat (inside,outside) source static' for me to an 8.2 version.
View 3 Replies View RelatedI try to get a ASA with the new software 8.4.2 running. On an old pix we had the nat command: static (inside,outside) tcp interface www 192.168.15.252 www netmask 255.255.255.255 0 0,In all the new documents about 8.4.2 I can find that it should work with something like:
object network web_host nat (inside,outside) static interface service tcp www www
I want to forward http traffic from the outside interface to this host. In the log I just get entries about blocking ACL - but both is allowed on the outside access-list - traffic to the inside IP and also to the outside interface IP.
I also tried it with "Public Server" - but when I try to use the Interface address I just get the message: Address x.x.x.x overlaps with outside interface address.
Is it still possible to do port forwarding on the outside interface?
I have two nic one connected with DSL modem with gateway 192.168.1.1 for Internet. another nic connected with office Intranet with gateway 10.226.122.x . I can connect only one network at a time disabling other.. I know route add command can be used for linking the both network so I can simultaneously use Internet and Intranet..can you elaborate with example (five years ago I set up the same with route add command.. now my memory failing..)
View 1 Replies View RelatedAny link to the commands in the Roman asa 55xx ? Did not find on Cisco's documents.
My small ASA 5505 crashed and comes up in Roman. Like to try get SW and Config back if possible.
I have a Cisco 3925 router running IOS 15.2 I am trying to configure IP SLA on it. The configuration is supposed to be what is pasted below. but the CLI is rejecting the commands.Its taking oly the "ip sla responder" command after that if I enter "ip sla 1083180034" command it says invalid input. [code]
View 5 Replies View RelatedI have configured the TACACS in my network and I have configured the aaa authorization commands 15 default if-authenticated group tacacs+ in Cisco 6504 Switch. Its allowing me to Login by Unable to run the Sh run commands ,i am getting Aithorization error emssage. If i am checking sh Privillage its showing level 15. Same configuration fine in other device with out issue.
View 2 Replies View RelatedAre the IOS commands the same on a router and a ASA for these two topics....CBT Nuggets where I train has 553 videos for some of the new topics. I am preparing for 554 as it has more ASA focus and thats more interesting to me.
View 1 Replies View RelatedHave a conceptual question bout CLI command authorization. We have ASC 5.2 up and running, providing AAA services for network devices. Now I need to make profiles for users in certain group to restrict dem CLI "rights" to show, clear counters and show running-config commands. I need to accomplish dis task.I should clrete separate privillege levele profile (let it be 2), specify commands at this level, assign Group this Authorization Prifile and make some additional changes in my devices.
View 26 Replies View RelatedI am looking to configure PBR in Nexus. The current setup in IOS is :
interface Vlan10
ip address 172.27.206.1 255.255.255.0
ip address 172.27.208.1 255.255.254.0 secondary
ip policy route-map Vlan_10_to_Corp
route-map Vlan_10_to_Corp permit 10match ip address Vlan_10_to_Corp
set ip next-hop 172.27.209.250!route-map Vlan_305_to_EFH permit 30
[code]....
But, Nexus PBR will not work with deny statements init. Now, what options do I have ?
we've got a pair of old 3745's that are getting upgraded to new 2911's, and I'm trying to run IOS 15.2 on the new routers to get them most current before going into test and production use.The routers are doing BGP, IPv4, and HSRP, and I'm trying to put one in at a time as to not have to big bang everything at once. I'm putting the one that matters least in first, and basically using the same config as the old one, which was running IOS 11.
I was using "no ip mroute-cache" on ethernet interfaces, and it says that command is deprecated and I should use the MFIB commands instead. Darn if I know what that means, I believe it was set up so the ethernet interfaces had IP multicast fast switching disabled, which was set up by our vendor 10 years ago so I'm not sure if it matters. It would seem logical to me this would have an impact on HSRP and speed of failover. Does this matter, and if so how in the world do I do this with IOS 15.2?The second one is the use of "no fair-queue" on our serial connection for a T1. This command isn't there either, and I'm not sure if I even need to bother on this. It was set up on the old router on a T1 Frame Relay circuit.
I need enable WPS function on WAP4410N. This is possible with CLI command #set wps enable. But how I can connect to WAP4410N with CLI?
View 1 Replies View RelatedI have just received 4 static ip's from my isp, i want to be able to point these ip's at different services on my internal servers, for example: [code]. The firewall I have is Cisco PIX 515, how to set the NATing up or commands?
View 1 Replies View Relatedtoday I received a Cisco Router 881G with PCEX-3G-HSPA-G for a customer that ordered a Router with the feature to send/receive SMS and to remotely active the 3G Internet connection through SMS. I believe that the router that meets this requirement is the Router 881G that I received today. In particular, the model is:
CISCO881G-K9
Now, I installed the router and configured the 3G link that is working properly BUT all the commands related to the SMS are completely missing. In particular, I miss the command:
cellular gsm sms send
gsm sms archive path
In the following documentation I see that these commands should be available: [URL]The fact that these commands are missing sounds very strange to me since the documentation is pretty clear. Do I need to activate any license? I also upgraded tha router to the last version...
Here it is the show version of the Router:
Cisco IOS Software, C880 Software (C880DATA-UNIVERSALK9-M), Version 15.2(3)T, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Sat 24-Mar-12 00:00 by prod_rel_team
ROM: System Bootstrap, Version 12.4(22r)YB5, RELEASE SOFTWARE (fc1)
[code]....
I have created a baseline template to run compliancy checks, I understand that lines beginning with a + are mandatory and lines begining with a - should not be on the router. What I need to know is, is there a catch all for any other commands on the router config (startup or running) but not mentioned in the baseline? For example, lets say this is my baseline:
+ service timestamps debug datetime msec
+ service timestamps log datetime msec
+ service password-encryption
+ hostname [hostname]
The router comes back as compliant as it has all the above lines. However there is obviously more config on the router, but this doesn't show? So I know I can get commands that are in the baseline but not on the router; but what about the other way round - on the router but not on the baseline? Surely this exists - at the least from a security point of view, an attacker could well have configured the Dot11Radio int, however without entering the command with the minus prefix I can't tell? LMS 2.6
How do I get a list of ALL IP addresses on a network using the DOS command prompt?
View 6 Replies View RelatedI am having issues recieving UDP response from my smart lighting control, i can here it in the same town but not from overseas..internal ip address 192.168.0.3 port 6000 it hears my commands from overseas i just cant here its response.
View 3 Replies View RelatedIn case I view the crashinfo file with more crashinfo:data, there is a "Log buffer:" section, which has logged all the commands executed by users.
View 4 Replies View RelatedWe are replacing two 3750E switches with 4500X using cat4500e-universalk9.SPA.03.03.02.SG.15111.GS2
1. is there a command reference available for this ios - can't seem to find out
2. Im using GLC-T gbics and we normally would set the speed to either 100 or 1000 now that option does not seem to be available.
3. when I entered username etc. I got a message " CLI deprecated soon".
To test the VPN performance of ASA 5540, I will have to build at least 1000 VPN tunnels. It is time-consuming works if I put all of commands line by line manually. It looked like a bundle of VPN tunnels won't be created by ASDM. I am wonder if there is any generator tool for this. I just tried to google it. I found a software is named as VPN Configure Generator, but it is not free.
View 6 Replies View RelatedI do not have the option to run sh mls qos commands. I am trying to look at the cos-map on my 7200 router. The code I am running is c7200-p-mz.122- 25.s9.bin.I also do not see the mls qos command listed globally and it is not an available command in config t mode.
View 1 Replies View Related