Cisco WAN :: 3845 - Correct To State That VWIC2-2MFT-T1/E1 Can Support Data In Addition To Voice
May 10, 2013
I have a 3845 edge router connected to the Internet via four T1s and a HWIC-4T1/E1 card. We are adding two more T1s to the mix, and I have a VWIC2-2MFT-T1/E1 card. Here are my questions:
1. Is it correct to state that the VWIC2-2MFT-T1/E1 can support data in addition to voice?
2. I can use the HWIC and VWIC cards together to utilize the 6 T1s together?
3. Do I just add the card, configure the new slot, and add it to the same channel group?
Below is the current config regarding the existing card HWIC:
card type t1 0 0
security authentication failure rate 3 log
security passwords min-length 6
logging message-counter syslog
logging buffered 51200
[code]...
View 1 Replies
ADVERTISEMENT
Sep 22, 2011
I have been advised by my service provider that to do ATM IMA I need an AIM-ATM and a VWIC2-2MFT-T1/E1 card, and that IMA is not support on the VWCI2-2MFT-G703 card.
View 5 Replies
View Related
Aug 7, 2011
I'm going to be swapping out a WIC-1DSU-T1-V2 for a new VWIC2-2MFT-T1/E1, going from one to two T-1s. This is on a 2800 router running 12.4(23)
configuration examples for the two T-1 setup ?
commands to verify the installation (show me the two T-1s are successfully bonded and communicating as one logical entity) ?
View 4 Replies
View Related
Oct 10, 2012
Can I use VWIC2-2MFT-T1/E1 along with NM-HDV2-2T1/E1 on 2921 and what is the minimum requirements for IOS image?As I understand, NM-HDV2-2T1/E1 is supported on 2921, however VWIC2-2MFT-T1/E1 is not, VWIC-2MFT-T1/E1 only. But VWIC-2MFT-T1/E1 is not supported on 2921.
View 1 Replies
View Related
Jun 15, 2011
I think I have my PPP multilink setup correctly. Though I am getting AL lights on one of my connections via a VWIC2-2MFT-T1/E1 card. One AL light is on at each location. Though I checked with my ISP and they said it was my network cables as everything looked good on their end. Currently one T1 circuit is connected at each end so users do not see a disruption. This is a new install with two routers and the config is shown below.
Router 1-----
controller T1 0/0/0
cablelength long 0db
channel-group 0 timeslots 1-24
(code)
View 1 Replies
View Related
Jul 19, 2012
I'm just double checking here because I saw one doc that didn't mention the 2900 on the data sheet but, I ve seen the 2900 listed with on others. I don't see the 2900s listed in this with the interface.
[URL]
View 6 Replies
View Related
Mar 8, 2011
i have VWIC2-2MFT-T1/E1 card installed in 2821 ISR router, ios (C2800NM-SPSERVICESK9-M), Version 12.4(25d).does this IOS supports unframed G.703 and also does this card VWIC2-2MFT-T1/E1 supports unframed????
View 9 Replies
View Related
Aug 10, 2011
the VWIC2-2MFT-T1/E1 hardware installation guide?
View 1 Replies
View Related
May 5, 2011
I purchased a 2911 months ago to connect a remote site via T1 circuit.I think I might be missing some hardware to make this work on the remote end. Currently have a VWIC2-2MFT-T1/E1 card.Does this WIC actually work with this router? So no reference that this VWIC works with 2911.
View 1 Replies
View Related
Dec 3, 2012
We have installed a VWIC3-2MFT card on a Cisco 3945 voice gateway but the router doesnt detect the card. out put is as below;
Router Version
============
System image file is "flash0:c3900-universalk9-mz.SPA.150-1.M.bin"
Cisco CISCO3945-CHASSIS (revision 1.0) with C3900-SPE150/K9 with 980992K/67584K bytes of memory.
[Code]....
View 8 Replies
View Related
Mar 12, 2013
We have two 3845 routers set up using HSRP at two locations (4 routers total) connecting inside to a pair of ASA 5520 (Active/Passive failover) on each side. These links are used for internet access and they work great under normal operating conditions - they fail over and fail back without issue. How ever, two weeks ago our operations guys started a new data replication procedure going across these links via an IPSec tunnel created between the ASAs. This seems to have created a situation where the IP SLA tracking is not be able to receive the ping back from the upstream router on the originating side. [code]
I have our SIEM set up to notify me whenever the router logs a State change and I got about 10 a day
View 2 Replies
View Related
Mar 7, 2013
I was just given a task to setup some T1 connections. We rarely use T1 interfaces anymore as they are typically just not enough anymore. I see the newer vwic3 interfaces are supported on various 2900 series but downloaded the vwic3 configuration guide and noticed that the 1900 series routers were not in the list? Is this correct. So are vwic3-2mft-t1 ehwic cards supported or not on 1921 routers? i can see the controller interfaces but not the ports as there must be additional configuration required. Im running 15.1(4)M4 IOS version that looks to be supporting the cards.
View 2 Replies
View Related
Jun 13, 2011
VWIC2-1MFT-T1/E1 card support on 1841 Router ?any ios up-gradation required?
View 1 Replies
View Related
Jan 15, 2012
I had already posted for voice modules for cisco 2811 but not able to find it. But here are a few questions regarding i
1. I am trying to configure a cisco 2811 with FXS ports . I am using an NM-HD-2V with a VIC3-2FXS. I am using the right modules. Also I believe we need PVDM mosules installed in the NM-HD-2V. We have PVDM-12 modules. Will that work or is 2811 compatible only with PVDM2-xx modules.
2. We are also trying to configure a cisco 2811 with PRI port. We plan to use an NM-HD-2V and a VWIC-1MFT-T1/E1. If they are correct and if we need only PVDM2-xx modules.
3. Also we are trying to configure a cisco 3845 with PRI and we plan to use the same as in 2811 that is NM-HD-2V, VWIC-1MFT-T1/E1. And here also we are not sure if we need only PVDM2-xx DSP modules.
View 7 Replies
View Related
Mar 14, 2012
we are using single cisco 3845 gateway as Ingress as well as vxml gateway . Can you provide any documentation regarding the call volume capacity this gateway can handle. We have deployed this gateway in a UCCE parent- child model.
View 2 Replies
View Related
Jan 9, 2012
Since CIPC is isntalled in the PC, and PC definitely getting an IP address from the data IP network segment instead of the voice IP network segment, so how to gurantee the following? 1. How the CIPC registered to the CME/CUCM 2. How to gurantee the QoS for the CIPC's voice traffic since the source IP address of the CIPC is belong to the IP network segment?
View 4 Replies
View Related
Sep 7, 2012
I intend to deploy a voice+data network using some old 3745 and 2811. The network in effect has six 3745 in a hybrid topology at different locations and each having three WIC-2T, one WIC-4T, three NMHDV-2E1. That's pretty much juicing out the maximum from these routers These will serve as my core routers and for access I will be using my 2811s with more VWICs and lesser WIC-2T to give voice and data to subscribers. The 2811s will have links to multiple 3745s. The NMHDV-2E1 will serve for the voice needs at the 3745 locations. All the WAN links will be E1. All my telephones will be on analog voice using traditional EPABX with CEPT/ PRI E1 cards for connecting to the routers. And for data, ethernet ports.Two of the routers will have E1 links to the PSTN and Internet which has to be extended to all my folks. Now, for the tricky part, all my network modules are refurbished stuff from ebay and all the ports will have links on them. I intend to use OSPF with only the backbone area.
View 7 Replies
View Related
Feb 13, 2012
I have a question regarding firewall configurations. Is it possible to have two interfaces ( for two internet service providers) one for voice and one for data. Can I have two Outside Interfaces that one will apply to a pppoe client group and the other will apply to a static IP? Is this possible and if so What would be the steps on applying this connection? Also to note I have a point to point connection already established for the pppoe. I also have another point to point connection for data, but however I do not know how to apply this to the firewall.
View 3 Replies
View Related
Apr 12, 2012
I'm struggling with a configuration issue on the Cisco SG200-08P. We are using the Cisco SG200-08P on a mobile cart that will go from class room to class room that will have computer and cisco Voip phone plugged into it. The issue is that each of our closets are in differnt VLANS ( 1 voice and 1 data....lets say data vlan 20 and voice vlan 2025 for conversation) and that we route to each closet.It would be great if I could just create a generic data and voice vlan to dynamically pick up what the upstream switch has however, it seems that I've been unsuccessful in doing so. I can pass the data Vlan no probablem. The upstream switch port is set to access port and a switch port access voice vlan (these are 3750x switches) If the above is not possible I guess I will take what I can get. Should I just create data vlan 20 and voice vlan2025 on the Cisco SG200-08P and make a trunk port on the Cisco SG200-08P and a trunk on the 3750x? Is there an option on the Cisco SG200-08P to tag voice traffic?I'm also concerned with VTP and I did not see an area in the Cisco SG200-08P to set that as a client and transparent mode.
View 6 Replies
View Related
Apr 14, 2011
I have a question its posible to authenticate an cisco phone and PC with the same vlan(voice and data)when i do this configuratión , the phone and pc dont work. The phone display registering and never finished.interface FastEthernet0/5 switchport mode access switchport voice vlan 1 authentication event fail action authorize vlan 11 authentication event no-response action authorize vlan 11 authentication host-mode multi-domain authentication port-control auto authentication periodic authentication violation protect mab dot1x pae authenticator dot1x timeout tx-period 10 dot1x max-reauth-req 3 spanning-tree portfastend.
View 1 Replies
View Related
May 24, 2011
How do i terminate a split cat5 for data and voice at the patch panel end?
View 3 Replies
View Related
Jun 4, 2013
If we configure a Voice and Data VLAn on a switch. And connect EX90 on voice VLAN and PCwith EX90 terminals. Than can we able to share a presentation or data with EX90 or not?
View 3 Replies
View Related
Dec 11, 2012
I wanted to know about EHWIC 8-Port configuration? We create Data and Voice VLANs and assign 8 ports to the VLANs. So how do VLANS communicate with each other? We cannot make Gi0/1 as sub interfaces and assign the same subnet IP’s as of VLAN IP’s , it wont accept. On 1921 router Assume Gi0/0 we connect to MPLS WAN. What happens to Gi0/1 where do we connect this?
View 1 Replies
View Related
May 16, 2013
im working in a new enviroment and want to makes some design changes to the environment. I wanted to bounce my ideas some of you folks to see if my thinking is on the right path or maybe i could do things better.
Setup:
Currently the setup that i manage includes and Sonic Wall (also dishes out dhcp), HP 1810 "Core Switch" and 3 SG 300-28P cisco managed switches. (all cisco switches tie back into the HP) The router is managed by the isp. There is only one vlan with all traffic going across it.
Obviously the glaring issue here is that voice and data all reside on the same vlan. Correct me if i am thinking incorrectly but the first step would be to create a separate vlan for the phones with its own IP scheme. currently phones are issued addresses from the 150-200 range and everything else is left for pc's, printers etc. To my knowledge the HP switch does layer 3 but i do not know much about it. There are vpn tunnels to remote offices that are used for sharepoint, email and to access other services. Trying to wrap my mind around the environment as a whole so i may be missing something obvious i could do design wise to improve.
View 2 Replies
View Related
May 24, 2012
I have to configure router 2811 for Data and Voice network.However I have only one Fast Ethernet interface. [code]
what else do I need to configure on switchport on which Avaya phones are connected.And is there any extra command, i need to configure on the router and 2950 switch.
View 4 Replies
View Related
Apr 8, 2013
I have a customer with several SG300's providing VLAN1 for data and VLAN10 for voice. The PC's are piggy backing off the phones and showing up in the SG300 fine:
One department has recently employed more people so we have an SG200 switch to connect the computers and phones to. I don't seem to be able to get any connectivity between the new switch and the SG300 it is connecting to. I have setup VLAN1 and 10 as per the images below:
View 4 Replies
View Related
Nov 6, 2012
I have one 2821 router. Which ios will support both voice and vpn?
View 1 Replies
View Related
Aug 27, 2012
I have a sge2000p to install with a uc520. I have all data traffic passing ok but voice will not work. Phones to not get ip etc.
View 4 Replies
View Related
Feb 5, 2013
We want to use a Cisco 861 Ethernet router to link our LAN's data and voice segments together (each on separate switches). Our switches are not Layer3 so routing over them is not an option. We only use the default VLAN1 on both switches.There is a data segment 192.168.1.0/24 and a voice segment 192.168.150.0/24, each with it's own internet/WAN access (internet for the data lan and SIP provider for the voice lan).
Diagram:
internet-~--router_192.168.1.1------192.168.1.0/24_data_lan--------192.168.1.254_cisco861_192.168.150.254-----192.168.150.0/24_voice------192.168.150.1_router--~-sip_provider
This is want i want to achieve:
- Link the data and voice switches using the 861
- I want to make the Cisco 861 the default gw on both segments, but they should only route traffic destined for the other segment to each other and route all other traffic to their segment's designated internet connection. I don't want the Cisco to do any NATting and there's no need for firewalling either.
View 3 Replies
View Related
Jun 28, 2011
when using SNMP on our cisco 3845 the traffic logs are set to refresh every 1 second but the data seems to come in 5 sec burst.so does not some a real time status of the interface throughput.
View 2 Replies
View Related
Apr 26, 2011
I'm about to install a new E1 onto my 3845 as backup line for my data network. We usually use VWIC2 cards since our infrastructure covers EU and US sites. But this time, I ran out of stock and so did my supplier. I have a VWIC-1MFT-G703 card here but not sure if it would work. What is the difference compared to the regular VWIC-1MFT-E1 ?
FYI, I run 12.4 T train release on my 3845s.
View 3 Replies
View Related
May 19, 2013
We have the below. Does this support Voice commands ? Or do we need a change of the router itself ? Or any licensing ?
C3825-ADVENTERPRISEK9-M, Version 12.4(24)T8
View 5 Replies
View Related
Apr 9, 2013
how many users supports the 2600 series ap air voice, video, and data average any document or link
View 3 Replies
View Related
