Cisco WAN :: 6500 Management Ip Address Configuration?

Mar 2, 2013

I would like to configure a Management ip address on 6500 by giving ip to the SVI. Following is the configuration done
 1) int vlan X
    ip address
    no shut
However i am not able to reach this Switch IP from other subnet's. for ex:- next configuration should be done, in order to make this work. I dnt want to use any routing protocol.

View 4 Replies


Cisco :: 5508 WLC Configuration / Can't Access GUI On Management Interfaces Ip Address

Aug 30, 2011

I've got a new 5508 wireless lan controller and can ping the ip address of the management interface, but can't access the GUI at the management interface's ip address.  I can access the GUI on the service-port interface.  No static routes in the controller; trunk appears to be set up correctly.

View 5 Replies View Related

Cisco VPN :: 6500 Mode Configuration / Address

Jul 17, 2011

In an IPSec port to DUT scenario, with Mode-Config set so as the DUT sends the IP address to the port, I get to a situation in which the DUT continuously enter the "Need config/address" state for the port, even if the port sends its ACK packet to every set IP address from the DUT.
The DUT is a Cisco 6500 Version 12.2 (33) SXI3, having Mode-Configuration configured to provide clients with IP addresses from a local pool. I enabled the "debug crypto isakmp" on Cisco, and below is an extract form the log file:
5d23h: ISAKMP:(80653):Need config/address      /* My comments here: This is the first Address configuration message from Cisco to port */
5d23h: ISAKMP: set new node 1768971286 to CONF_ADDR
5d23h: ISAKMP: Sending private address:
5d23h: ISAKMP:(80653): initiating peer config to ID = 1768971286
5d23h: ISAKMP:(80653): sending packet to my_port 500 peer_port 500 (R) CONF_ADDR
5d23h: ISAKMP:(80653):Old State = IKE_P1_COMPLETE  New State = IKE_CONFIG_MODE_SET_SENT

above debug messages that Cisco produces I can not realize why Cisco resends the IP adderss configuration message for remote peer. Any other methods to use so as to get the reason behind this behavior? Or any explanation to the above behavior?

View 1 Replies View Related

Cisco :: 6500 IOS Switches - Compliance Management In LMS 3.2?

Oct 11, 2011

I'm having a hard time getting Compliance Manager to accept a "banner login" command I'm attempting to use on 6500 IOS switches. I've edited the template, tried cut-&-paste, looked for the archive file on the server to directly modify it (without success), among other things. I have this feature functioning correctly on CatOS switches, but can't seem to get it properly set on IOS switches. What's the limit, as far as the template is concerned, on the number of characters with this type of command? Where are the archive configs located on the server; in the "shadow" directory?

View 1 Replies View Related

Cisco Wireless :: 6500 Unable To Reach WISM2 Management Interface

Mar 28, 2012

I've just reset our WISM2 in the test lab back to factory default as I needed to reconfigure the 6500 and the WISM2 itself. Bearing in mind I had it working before.I've just renamed and re-addressed some of the vlans so things flow better and make it easier to add more WISM2s in the future.Now I've run through the initial configuration and it's rebooted ok and show WISM status is showing Oper-Up and there's a port channel 407 been created as I would expect. However, I am unable to get to the management interface via GUI or SSH. In fact from the 6500 I can't even ping the management interface (but I can the service port).The Vlans have been changed in the 6500 config so it knows the native-vlan and service vlan etc and all the vlans are up/up.

View 17 Replies View Related

Cisco :: Module In CW To Get MAC Address And IP Address Of All Switch Ports On 6500

Oct 13, 2009

Is it possible using any module in CW to get the MAC address and IP address of all switchports on a 6500?

View 6 Replies View Related

Cisco :: Configuration Of Management On LMS 4.0.1

Dec 6, 2011

I'm using LMS 4.0.1 (current patches and device packages)
There is a problem with the configuration fetch.There are some 2503 routers with IOS 11.3(6) and the message on LMS is:  Couldnot enter ENABLE Mode from USER Mode on Device
The devices arn't configured with username, only telnet pw and enable pw; no access-lists or other limitations configured

The credential check is ok ... multiple checks done ... devices deleted, new discovery ... devices deleted and manually added .... with the link  //serverip:1741/rme/ I've changed the timeouts multiple times (up to 60 seconds for TFTP, SNMP) .... all these have had no effect of the config fetch

View 2 Replies View Related

Cisco :: Configuration Management In LMS 4.1 Is Not Working?

Jan 9, 2013

I need to archive the configuration for the devices but it states that SSH fails to authenticate although I have checked the credentials many times.

View 1 Replies View Related

Cisco :: Basic Ace30 Configuration For Management Access

Dec 13, 2012

in lab trying to run a test upgrade of an Ace30,can seem to get it right ace30 is in slot 1 of the 6500, management vlan 10

View 4 Replies View Related

Cisco :: Ciscoworks 3.2 RME Compliance Management With 802.1x Port Configuration

Nov 6, 2011

i am currently trying to use LMS 3.2 Compliance management to verify and alter our access port configurations for 802.1x. Below is our current configuration

View 1 Replies View Related

Cisco Switching/Routing :: 4900M Management Configuration Via Vrf

Mar 10, 2013

I am just going to deploy some new 4900Ms for a customer. Want to know if configuring management for 4900 (everything like NTP, AAA, SNMP , DNS ) is doable through management interface in management VRF and there are no caveats to be aware of.

View 1 Replies View Related

Cisco Wireless :: AP 1242 Shows WLC Management IP As Its Own IP Address

Jul 14, 2012

we are using wism 4404 code 4.2 , we are using this old code becuase of 1250 mesh APs, now when a user connect to our network and he is using intel proset software he can see details of our AP, like mac, type and AP ip address 9 which in this case it the controllers ip address) is there a way we can prevent the ap from showing it?...we will be doing an upgrade to 7.0.230 soon. will the upgrade takes care of this problem or there is a way to fix it.

View 5 Replies View Related

Cisco Wireless :: 3502 - Set NAT Address For Management Interface

Oct 19, 2011

I have got a 3502 setup and functioning in Office Extend mode. I have found one issue though. I have to set the checkbox on the my Management Interface to Enable NAT Address and put the external address in the box. Once this occurs no internal APs can join the controller.
Need setting this up with a single controller behind a router and not having to set the NAT Address for the Management interface? Should I setup a second interface on the controller to be for external management?

View 9 Replies View Related

Cisco Wireless :: AP54N - Management VLAN-ID Matter In Configuration?

Aug 16, 2012

I am working to configure AP541n AP,  is able to connect to the AP wired, assign AP static IP with proper subnet mask & default gateway, when it's done, everything looks perfectly, but since I changed the management VLAN ID from 1 to 2, I can't even connect to the AP wired from the PC, why does the change matter?

View 2 Replies View Related

Cisco Application :: ACE 4710 - Context Management / Backup Of Configuration?

Jun 25, 2012

I am looking at management (backup of the configuration) of the ACE 4710 running A4.1, the management software is Cisco Cirrus. The question I have is around the management of the context's, I have a backup of the Admin but would like the user context's also, how this is completed.              

View 3 Replies View Related

Cisco Switching/Routing :: 4900M Management Configuration Required

Dec 8, 2011

I am just going to deploy some new 4900Ms for a customer. Want to know if configuring management for 4900 (everything like NTP, AAA, SNMP , DNS ) is doable through management interface in management VRF and there are no caveats to be aware of.

View 1 Replies View Related

Cisco Wireless :: WAP321 Configure IP Address On Management VLAN

Feb 26, 2013

I have a WAP321 I am trying to set up.  It's connected to gi1/23 and the switch system mode is set to router.  The rest of the network works just fine.I have an SG500-28p and the port. [code] On the WAP321 wizard, configured IP address on my management vlan and also configured the default SSID on that vlan.  That works. (I plan to remove that one) Then I add the two SSIDs for vlan 20 and 22 (private and public access)  and I can't associate to either of the two additional SSIDs. I haven't configured any other settings beyond the wizard and adding the other two SSIDs.  I do want cisco mobile ios (jabber) to work on the private network and also do have a couple spa525g2s that need to connect wireless.

View 1 Replies View Related

Cisco Switching/Routing :: Set Management IP Address And Gateway On A 4500?

Apr 24, 2012

In mucking around with my 4500 I accidently deleted the ip address that I use to get into it with telnet and CNA. I have a console cable hooked up to and I'm in that way but the commands I got off the internet did not work. Those commands were set interface sc0 10.x.x.x/xx and set interface me1 10.x.x.x/xx. It didn't like interface and I notices when I did a set ?

View 6 Replies View Related

Cisco Wireless :: WLC 5508 As Dhcp Server For AP Management Address

May 26, 2013

My 5508 WLC which runs version 7.4 is configured as a DHCP server for the AP management and here's my problem: My AP can get to the address, and can ping the address of the WLC management,But my AP prompts the following log: [code]

In the switch dhcp we can use to do the WLC option43 specified address, but in this case how the address specified WLC, the AP can be registered up?

View 9 Replies View Related

Cisco Switches :: SRW224G4 - Cannot Access Web View Management Interface Through IP Address

Jul 12, 2012

I am the Systems Admin at LDM Media and am trying to get some support for one of the SRW224G4 managed switches we have in our rack. The issue is as follows:

Any endpoint connected to the switch is assigned an IP address in the range of 169.254.154.XXX regardless of the switches set IP range, the second issue is that I cannot access the web view management interface through the default IP address (and I have tried to use the last IP in the range set by the router, to no avail)
How to regaining control of this supposedly smart switch?

View 3 Replies View Related

Cisco :: 6500 - Unable To Get Configuration

Dec 5, 2011

We have an issue with our 6500 catalysts.
We are regularly seeing the error above on our cat6500 devices when executing  a 'sh run ' command:
We've seen this error for quite some time but the frequency seems to be increasing up to the point where it becomes problematic now because backups and other automated actions are failing regularly.
We don't see multiple processes with the commando "sh config lock" at that time. But when we do a "sh users", we can see sometimes multiple users.
I supose it is possible for multiple users to do a logon at the same time, but not make changes at the same time.
We are using IOS  s72033-ipservicesk9_wan-mz.122-33.SXI7.bin. It seems that all switches with these IOSses seem to have the problem. But in the bug toolkit I can't find any reference to a bug...

View 3 Replies View Related

Cisco Routers :: RV042 / Login Screen On WAN Address With Remote Management Disabled

Aug 28, 2011

My first try at configuring my RV042 has had unexpected results. I set a WAN and LAN address, but did not enable remote managment and did not configure any port forwarding.  I expected to be able to connect to the router on the LAN and I could. The surprise came when I put in my web address.  I got a router login page.  How do I suppress than on the WAN side.  I have a static address with my ISP.

View 1 Replies View Related

Cisco :: 6500 / 1250 - NCS Implementations And Configuration / VSS

Mar 22, 2013

I am new to the NCS implementations and configurations. I have one very  specific case with Cisco Prime Infrastructure 1.2 and autonomous APs  and several issues with Cisco VSS on 6500 switches. So here is the version from Prime:
NCS/admin# show version 
Cisco Application Deployment Engine OS Release: 2.0
ADE-OS Build Version:
Well  the issue what we have now is that access point has been added but its  not recognized by the NCS prime. I have tried all three versions of SNMP  but I get the same result. The SNMP configuration is valid since I use  the same for my switching infrastructure. When I enter "debug snmp packets" and "terminal monitor" I can see the SNMP communication between Prime and Aironet 1250 which is standalone.
When  I switch to Life cycle theme and go to Operate > Device Monitor  Center I see all devices I have added. The Aironet 1250 is reachable but  under collection status I get Managed with Warnings. When I hover over  with my mouse I get "None available".
I  have successfully added my switching infrastructure in total, which is  operating perfectly for Catalyst 2960/3650/3750/4500 series but for 6500  under VSS I have some warnings. The device is recognized by the system  which is excellent and all is operational. I get the following errors  under Collection Status:
feature_sensorSNMP request timed outfeature_powerSupplyFanStatus-6kSNMP request timed outIdentityCapabilityThe device is unreachable.feature_flashdeviceSNMP request timed outsam_ipsla_featureThe device is unreachable. 

What can be done to resolve these issues ? I have attached a screenshot of this particular issue. The affected access point is

View 4 Replies View Related

Cisco :: Network Address Translation On 6500?

Nov 22, 2012

We've got an application that is running on our LAN that is using IP addressing to connect to the server (they refused to use DNS).The server is now being moved to a VM which will be on a different subnet. The supplier is now concerned that there will be a big down time due to him having to reconfigure each device (about 100) with the new server IP. If the server was external I know I'd be able to do NAT on the FW to make this work but can it be done internally on my 6500s? I want to have the devices pointing at their hardcoded IP address off and NAT the destination to the VMware servers IP Is this possible using cisco NAT?

View 13 Replies View Related

Cisco Switching/Routing :: Catalyst 6500 - DAI Configuration

Apr 26, 2012

Any step-by-step configuration guide of how to enable DAI on Cisco Catalyst 6500 Series Switches.

View 1 Replies View Related

Cisco Wireless :: 6500 - DHCP Client Not Getting Address

Oct 31, 2012

Currently we're providing DHCP to wireless clients from a dhcp pool on a cisco 6500. Due to new requirements we need to move to windows 2008 dhcp and when I test this on an unused WLC ( the client doesn't get an address.
When I do a packet capture on the client I see it requesting dhcp but not getting any response from the server. When I do a dhcp debug on the client I see the same (see attached file).
This seems to me to be a server issue but the same server is supplying addresses to wired clients.

View 3 Replies View Related

Cisco Switching/Routing :: 6500 - Same MAC Address In Different VLAN?

Oct 31, 2012

The customer has 4 6500 switches.  2 Physical locations, and 2 switches at each locations.  The locations are connected via 1 200mpbs metro ethernet(layer 2).  We ran into an issue during a DR exercise.  We had created a VLAN for DR testing purposes, that did not have any SVI configured, but the VLAN did exist on one of the 6500s.  When the customer restored a VM to the DR VLAN, we lost connectivity to the production server.  After some troubleshooting, we found the cause to be the same mac address showing up, but in a different vlan.  Once we removed the DR vlan from the 6500 all was well.  It seems like switches are ignoring the VLAN in the mac address table, and forwarding to the incorrect ports.  The switch is not reporting any mac flapping in the logs.  No spanning tree topology changes are occurring.  Code version is 12.2(33)SXJ2 on all switches. 

View 1 Replies View Related

Cisco Switching/Routing :: WOL Configuration On L3 Catalyst 6500 And L2 2960G?

Dec 20, 2011

I got problem with wake on LAN software.. The software unable to ON all pc's remotely if sitting under different vlan. Everything is ok if using the same vlan. Below are the network diagram & switch configuration.
Layer 3 switch Intervlan routing configuration
ip forward-protocol udp 7
interface Vlan4
description vlan Client-WOL
ip address
ip access-group Deny_HTTP_Vlan1 in
ip helper-address

After configured all the switches with the above setting, the software still cannot wake all the pc's using LAN. Base on sniffing, i can't find UDP port usage by the software. Attached here with print screen from wireshark.

View 7 Replies View Related

Cisco Switching/Routing :: 6500 - Campus OSPF Configuration

Aug 26, 2012

I manage a small/medium sized campus network consisting of 4 Cisco 6500 series chassis (each with SUP720's) and a couple hundred Cisco 3550/3560/2960 edge switches. We recently completed a new leg of fiber that will make a completed loop between all of the 6500's .... before I make the pyhsical connection I need to figure out my OSPF entries on each 6500 switch.

View 4 Replies View Related

Cisco Switching/Routing :: Catalyst 6500 VS-SUP2T-10G QoS Configuration

Apr 22, 2013

I am migrating services from SUP720-3B to VS-SUP2T-10G= and moving to a VSS configuration  between a pair of Cat6506 distribution layer switches. I need to enable QoS on these switches, primarily to trust dscp and also to prioritise voice traffic. The autoqos feature works for some ports but does not work on port-channel interfaces and port-channel member interfaces. How can I apply the qos settings for these interfaces in line with what auto qos would normally provide. My line cards are as follows:
Civic_6506VSS#sho mod
Mod Ports Card Type                              Model              Serial No.
--- ----- -------------------------------------- ------------------ -----------
1    4  CEF720 4 port 10-Gigabit Ethernet      WS-X6704-10GE   


View 1 Replies View Related

Cisco Switching/Routing :: 6500 Changing Switch Configuration

Aug 27, 2012

I am going to change a running 6500 switch. I am missing a best pratice doc for changing a cisco switch configuration. My question is if a startup-config has an error (due to typo mistake, or due to comands not supported on latest IOS) and I do copy tftp startup-config then what will happen ? I want to make sure when I do "reload" the switch then it should boot normally with the latest startup config !

View 3 Replies View Related

Cisco Switching/Routing :: Best Configuration Between Vmware ESX Server 6500

Dec 6, 2012

what is the best configuration between vmware ESX server with 10 Physical NIC card and cisco 6500 , This ESX Server host 12 vm with VLAN 100,150.200.

View 6 Replies View Related

Cisco Application :: ACE And FWSM Design And Configuration Guideline With 6500

Apr 8, 2013

I have Cisco 6500 with FWSM and ACE module which are in one central DC. Also we have four different Datacenter (Hub & spoke) and in our FWSM we have configured four contexts in central DC FWSM for each DC. Each DC servers are different VLAN and IP subnet. Now we have to configure ACE module for load balancing among those different subnet servers. What will be the design and configuration for this solution? Like routed or one-arm mode design.
Scenario Example:
1.  App Server01
FWSM Context: DC1
Physical Location:DC1

Now customer requirement is we have to load balance using ACE between these App Servers which are in different context s in FWSM and one Server is not FWSM. how to configure or design or placement of ACE and FWSM for above scenario.

View 4 Replies View Related

Copyrights 2005-15, All rights reserved