I have a 7606-S router ( non redundant ) with SUP32 and i wand to replace it with RSP720-3C-GE , i am asking about the procedure?
-shall i switch off the router ? or just removeSUP32 and insert RSP720 ?
-are there any steps should i do before the upgrade ?
-i am planning to take the router out of service during the operation, how much down time it will be ?
I have to do a migration of sup32 to RSP720 for which I need to know if you can operate the equipment connected with the 2 supervisors at the same time??? and it still working ?
View 1 Replies View RelatedI have a 7606-S router ( non redundant ) with SUP32 and i wand to replace it with RSP720-3C-GE , i am asking abouth the procedure?shall i switch off the router ? or just removeSUP32 and insert RSP720 ?are there any steps should i do before the upgrade ?i am planning to take the router out of service during the operation, how much down time it will be ?
View 9 Replies View RelatedI need to create a policy to provide only 4 Mbps bandwidth for mail out of 16 mbps pipe terminated on 7606 router (at Datacenter) having WS-SUP32-GE-3B.But I can't create policy with bandwidth percent,even exact value with priority command does not work. When I am going to enter service policy output command at interface it is showing as"priority command is not supported in output direction for this interface Configuration failed!" All I want to restrict bandwidth at backbone link for mail traffic. From all remote locations use to access mail server over the same link.
View 1 Replies View RelatedI have a cisco 7606-S with dual RSP720-3CXL. Devices reloaded and now none of the RSPs are booting.When I have tried to take the console using only one RSP, card going to rommon mode after that it hangs. I guess its firmware is corrupted.
View 4 Replies View RelatedI have been tasked to replace a failed sup on a 6500 Sup32 running IOS. Now, the primary sup doesnt have a compact flash. I don't have any CF on me. The replacement sup i received also doesnt have a CF.From the cisco website it says that the moment I insert the secondary sup into the chassis. it will automatically download the IOS and boot details from the primary to the secondary sup.
[code]....
I need to put a FWSM and a line card WS-X6148A-GE-TX to a router 7606. The FWSM version is 3.2(13). The router is running IOS 12.1(18)SXD3. The Cisco document here says the required IOS for router 7606 is 12.2(18)SXF or higher. I have downloaded the IOS 12.2(33)SRD4 and loaded it to the flash card. When I turn the router on, it doesn't load the new IOS and goes to rommon. Which IOS I should use to make the router 7606 work and accept the FWSM.
View 2 Replies View RelatedWe are planning to configure the ipv6 PBR on our 7606 routers. We have configured the route-maps successfully .but when we tried to apply those on interfaces we are facing an problem .
when we trying to give command # ipv6 policy route-map <route map name> . we are unable to find policy command option in the command list.
IOS Version : c7600rsp72043-advipservicesk9-mz.122-33.SRE3.bin.
I found that there is no force-switchover command under redundancy configuration mode. How can I do a switchover from primary RSP720 to secondary RSP720?
I am using SSO and NSF.
C7609-2(config)#do sh redundancy
Redundant System Information :
------------------------------
Available system uptime = 1 hour, 51 minutes
[Code]....
We are installaing a new RSP720 on 7606 platform and facing a peculiar problem. It is prompting for a enable password. We have not configured anything on router yet, still it is asking for enable password.
View 3 Replies View RelatedAny know how to close these open ports on my Cisco 7606 router? Any know what these TCP ports are used for?
:
49 - Not sure what this one is other than what IANA reports about TCP port 49
4510
4509
2222
:
I'm sure I could add an ACL to block communications to my router based on this ports but would rather figure out how to close 'em so this already overloaded router doesn't have additional processing.
Im having problem configuring policies for limiting traffic on subinterfaces on cisco Router 7606-S. I have configured:
[code]...
So for egressQOS , i want to configure with police, not shape (for the memory reason).
How can we confirm the memory requirement for a RSP720-3c-ge card ?I got a link for 6500 series [URL]
View 2 Replies View RelatedAfter inserting a RSP720-3C-10GE in module 6 and running the show module command display the following [code]what is the meaning of the UnKnown on the oline diag status ?
View 1 Replies View RelatedIs Enhanced FlexWAN module compatible with 7603-S with RSP720-10GE?We have a PA-POS-2OC3 on a 7200 router and we want to use it on 7603-S.
View 1 Replies View RelatedSince a couple of months, I have some CPU problem.
There is no high process :
l#sh processes cpu | exclude 0.00CPU utilization for five seconds: 39%/30%; one minute: 32%; five minutes: 32% PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 130 52713208 240359987 219 0.95% 0.91% 1.00% 0 IP Input 202 1811824 1218190 1487 0.07% 0.06% 0.05% 0 HIDDEN VLAN Proc 338 20873364 219225 95214 7.11% 0.94% 0.71% 0 BGP Scanner
total amount of traffic on the router around 700Mb-1Gb out / 300Mb In
cisco CISCO7603 (R7000) processor (revision 1.1) with 458752K/65536K bytes of memory.Processor board ID FOX090308DTR7000 CPU at 300Mhz, Implementation 0x27, Rev 3.3, 256KB L2, 1024KB L3 CacheLast reset from power-on5 Virtual Ethernet interfaces9 Gigabit Ethernet interfaces1915K bytes of non-volatile configuration memory.
65536K bytes of Flash internal SIMM (Sector size 512K)
I have a sup 32 (WS-SUP32-GE-3B) i dont find any msfc card ? is there any command to check if msfc is present or offline/online ? Also will i be able to upgrade IOS for this sup with out MSFC ?
View 2 Replies View RelatedHow to replace fan incisco 2811 router in live or down condition?
View 2 Replies View RelatedI am going to upgarde SUP2 to SUP32 on my 6509 by next week. right now I have 2 SUPs on the 6509 in redundant mode.
View 5 Replies View RelatedI need to upgrade 2xsup2 module to 2xsup32 on my cisco 6509. I just found out that I can not have the CISCO WS-X6500-SFM(Cisco Switch Fabric Module switch) with Sup32 and I have to remove 2 xCISCO WS-X6500-SFM2 modules from the switch.I am using this switch as a access switch and most of the ports are 100Mbps.
let me know if the upgrade would be safe or not as far as the bandwidth?
My home router is an aging D-Link DGL-4100 and I am looking to replace it.My max budget is ~$250 USD.
I use 2 Ubiquiti Unifi UAP-Pro APs in my home for WIFI access, so I have the WIFI aspect of my home network covered completely. All wiring in my home is either Cat5e or Cat6, my switch is a gigabit HP ProCurve 1810G-24, and my cable modem is a Motorola SB6120 (Comcast cable broadband). I have 7 IP cameras (security system), 4 streaming media players, several PCs, a server, and several other network connected devices. I am the only resident.
I am looking to maximize my WAN to LAN (& LAN to WAN) throughput while maintaining a very secure network. I also want the router to have reliable VPN. If it is a wireless router, I would most likely not utilize the WIFI feature, probably turning off the WIFI radios and just use the router functionality.
I don't have the time/patience to build a PFSense (or similar) box and learn the software, so am only considering an off-the-shelf solution. Yes I know that PFSense and Untangle are great, I simply don't have time to learn them presently or in the foreseeable future.So, which router for wired performance and security would you recommend?
We use a 3825 router to screen alot of the junk from the internet side or our firewall. Its worked well for the last 4 years buthas rebooted multiple times in the last month for no apparent reason.At this point I think I would prefer to replace it.Our current internet link is 100Mbps and this router handles that quite well. Is there an equivalent that I should replace it with, or should I just buy another 3825 ?One with an OOB management port would be nice.
View 6 Replies View RelatedOur one of the Client need to replace CISCO 831 router with high end router , there will be around 60 to 70 users accessing this router for Internet surfing. Right now 831 having 3 Ethernet and 4 Fast Ethernet Ports.
View 4 Replies View Relatedin my lab environment, I have a site-to-site VPN between a Pix515E and Cisco 3845 router, using AES-256/DH-5/SHA for isakmp and AES-256/SHA/PFS group5 for the site-to-site VPN, I can only push about 26Mbps IPSec traffics (tested with Iperf). CPU on the Pix515E is running at 96% utilization
Now if I replace the Pix515E with another Cisco 3845 router, I can push about 100bps. Why such a big difference between the data sheet and actual real world
[code]...
I have (2) Sup 32 configured in a 6509 chassis. I have 1 power supply plugged into the wall and 1 power supply that is not plugged into anything but it is in the chassis and has green light to show that it has been recognized.
My problem is the "system light" on both sup32 remains amber and does not turn green. I have done show modules and sh diagnostics and sh power and everything checks out OK. Also there is an amber light on "active" on the 2nd Sup32 which I am assuming means that it is in standby mode so that would be correct.
Q: My question is could it be the power supply that is not plugged into anything causing the "system light" to stay amber and not turn green?
Q: Will this amber system light on the Sup32 stop the 6509 from running as normal?
I had an issue yesterday with no internet access on my desktop computer; the message said "Network cable unplugged" so I called AT&T tech support for assistance. I have 2 Dell computers; a desktop and a laptop which I use wirelessly in the house.After doing several things from disconnecting the router to try and determine if the problem was with my router or an ethernet cable AT&T determined a port on my router which is 6 years old could be going bad and recommended I replace my router.I contacted Linksys yesterday; spoke to tech support for my WRT54G router and was given 2 model recommendations. One was a Model E900 N300 and a more expensive model; an EA2700 N600. There is a price difference of $40.00 USD between the 2 models. I could probably get by with the E900 N300 for $49.99 but the guy at Linksys was putting the pressure on me to buy the more expensive one for $89.99. I told him I'd have to think about it.
View 5 Replies View RelatedI understand that my questions seems to be rather strange cos supervisors is rather old (Sup1A especially). But i am interested in understanding what puprpose were in production SUP32. I cant find out enough differencies between Sup1A with MSFC2 and Sup32 to understand what reasons lead to deploying new sup in none fabric supervisor series.
Both supervisors have same perfomance - 15Mpps and have limitation on backplane bandwith of 32 Gbps (cos both use swithing bus), both supervisors equipped with MSFC2 and etc. Differencies i found:
SUP 32 have 10Gbe ports support (but this seems to be doubtful enhancement - with it perfomance GE ports seems to be more appropriate technology isnt it?) SUP1A equipped with PFC, SUP32 with PFC3BSUP32 deploys CEF (what is benefit of CEF if perfomance same?)
I am in the process of trying to replace a modem/router,the switch does not work with the new modem/router although if I connect the modem/router directly to my computer it works fine,so its not a router issue.I suspect that the settings need to be changed in the switch to allow the new router to work ?
View 1 Replies View RelatedI have a Cisco 1921 to replace our current router which is constantly freezing. We have a couple inside servers, one is a web server and application server which needs to be RDP'd to by a couple of clients outside of our network. I cannot get this to work no matter what. I know it's not the server's setup as when I plug the network back into the old router, it works just fine.
All clients have access to the internet, and I can successfully ping/resolve hosts from both the router and a client computer connected. I cannot, however, rdp using neither our public IP, nor our hostname. The hostname does resolve to our ISP assigned IP, but the server cannot be contacted, leading me to belive this is a NAT issue. [code]
I have a Cisco ASA5505 with Frontier ADSL. I broke into their crappy little modem and obtained the settings needed to replace their modem with a 2621 router with a WIC-1ADSL module. I have a static IP from Frontier which is on my ASA5505 and the Dialer interface on the 2621 gets its address from Frontier via DHCP. There are devices behind the ASA which I need access while in the field, IP Cameras, Seed Treater, etc., so I have Anyconnect running on the ASA and can access everything from my laptop, iPhone and iPad from whereever. The issue arises when my laptop is in house and communicating with my parent company and I try to make a cell phone call off the network extender. The call is choppy since there is no QoS and the data is strangling the voice. Since I have control over the 2621, I added another network and NAT it into Frontier without them knowing. I have since placed the network extender on this network as well as a WAP200 that is wide open for my customers when they are in the office. Doesn't fix the problem but...
I have now added Evertek Wireless internet with a static IP also but they use a reservation based on the MAC Address of my interface of the ASA. This plugs directly intot the ASA via ethernet (I would assume their antenna is just a wireless bridge). I set route tracking on the Evertek side and use the Frontier as a backup and all devices on my NAT network still funcion on Frontier DSL and all my nornal data traffic is out Evertek. The issue is that the Evertek Wireless is not very fast or reliable (today in during a snow storm, it could barely keep an internet connection). And I had a problem with Anyconnect using either connection. I got that working. But think that the "ip address x.x.x.x y.y.y.y dhcp setroute" on the Evertek side messed things up from a routing standpoint when I would connect from the outside on the Frontier side. For testing, I switched the tracking around and now the connection on the Frontier side does not work but that is besides the point.
Frontier is going to try out an ADSL/2 connection next week which brings up another issue; all Frontier connections come into my buidling on a single 4-pair wire so if they go down, all my internet except the Evertek goes down. I have a Raven Slingshot coming for installation shortly that cannot go down; it will provide RTK (sub-inch accuracy GPS) to my customers that have auto-steer and auto-shutoff capabilities in their tractors via cellular data modem. So, while they are planting their crops in the field, if my connection goes down, their tractor will not function.
I also had a Cisco UC320W but it died a few days after it went off warranty so I replaced it with a Dell Server running 3CX IP PBX that supports Cisco SPA525G2 and SPA501G IP Phones. There is a 3CX iPhone app that allows me to receive calls while in the field, it uses a proprietary tunnel that I have open on the ASA. With 4-pair coming into my building, I will be left with a single 1-pair for phones so I am considering a SIP provider instead.
Can/should I move the Evertek ethernet to the third ethernet interface on the 2621 and track the Frontier DSL against the Evertek (backup) on the 2621 side and use the ASA to track the ADSL/2 against the 2621? Should I acquire an 1841 (or some other device that suppports the HWIC) with a ADSL/2 card and use HSRP between the 2621 and 1841? Is that even possible?
I have a 2651 that has an adsl1-wic that I am using as my DSL router. I recently acquired a 2801 that I want to replace the 2651 with. I configured the 2801 the same way as the 2651 but on a reload I get the statement that says
Setup: New interface NVIO placed in shutdown state
When I do a show interface all of the interfaces show up except the NVIO and I don't have any connectivity to the outside world. I am using Nat since I have a /29 and using nat pool overload. What am I missing? I am running IPVOICEK9-M 12.4.25c on the 2651 and adventerprise 12.4.24.T on the 2801
install a new N600 Wireless Dual Band Gigabit ADSL2+ Modem Router - Model DGND3700, to replace a Thompson Speedtouch USB Modem.
PC Windows XP Home Premium Media addition - Main PC X2 Laptops Win7 & Vista - fully working on wireless no issues.
I have managed to get two laptops working wirelessly with no problems, my main problem is the master pc needs to be able to use this router as well, but I cannot get it to work via the Ethernet cable!! I can get to to the Routers config page, I have done the following:
unplugged and removed the speedtouch modem, the old dial up connection is still available on the pc along with the speedtouch software and driver, I left this in place just in case the pc needs to revert back to the speedtouch modem, if I am unable to resolve this issue.
I have set the ip address on the PC to static and input the relavent Subnet and Gateway I can ping the Routers address 192.168.0.1 even though I have reserved the PC's Mac address and IP Adress I am unable to get to the internet. I have tried setting up a new internet connection via windows wizard.
when i look into the nework connections section in windows the local area connection is 100mb and there seems to be another connection which looks like another internet connection this indicates I am connected however I still cannot get an actual google session running.
I am looking to replace my current WAG54GS Gateway with the EA6500. Problem is the new one does not have a built in ADSL2+ modem (I am in the UK and my ISP is Demon Internet). I therefore need to purchase a separate Modem to connect to the router.
View 9 Replies View Related