Cisco WAN :: 871 Can't Ping From Host

Jun 30, 2012

I'm going through the CCNA training and I'm setting up my DHCP server on my 871 router. I have my cable modem into the WAN port on my router and have 1 host plugged directly into Fastethernet 1. I can ping any IP I want from the IOS prompt but I only have local access from the host. [code]

View 4 Replies


ADVERTISEMENT

Cisco VPN :: Pix 515e - Remote Host Cannot Ping Any LAN Host

Jun 27, 2011

I have a host that can successfully connect to a PIX 515E (7.x OS) via VPN Client; however, I have no IP routing to the LAN from the remote host.The VPN IP pool works finem,The LAN default gateway is the inside interface on the PIX; the network is flat L2 behind it.The default route on the PIX points out; no other routes are defined,The VPN remote host can be pinged from LAN hosts, but the VPN remote host cannot ping any LAN host, not even the PIX inside interface.

View 2 Replies View Related

Cisco VPN :: ASA 5510 Ping / Communication Host To Host

May 7, 2012

ASA 5510
Ver 8.2(5)
 
I have been looking all over the place for the answer of how to allow clients on an IPSEC VPN to ping from host to host.

View 4 Replies View Related

Can Pure IPv6 Host Ping A IPv4 Host?

Feb 10, 2011

I'm just wondering if its possible to ping an IPv4 host using the IPv6 host assuming that the NAT64 has already been implemented?
[code]...

View 2 Replies View Related

Cisco Switching/Routing :: Can Ping From R1 To R3 SVI4 Gateway But Cannot Ping Host

Dec 12, 2011

I set this up and I can ping all the gateways but never the hosts.  I was hoping I could make these links between 6500's a mix of L2 and L3.  Check it out.  They are connected in a linear fashion R1--->R2--->R3.  I can ping from R1 to R3's SVI4 gateway but I can never ping a host on that SVI4.  I was hoping that I could use the port-channels between 6500's as routed links or as trunk links depending on the type of traffic....thought it would ease the migration.  I suppose I could always get rid of the port-channels and just make separate L2 and L3 links between the 6500's.

View 3 Replies View Related

Cisco :: Can't Ping From Outside To The (online Host) PC

Aug 26, 2012

I tried to ping from the "online host" PC to the outside,it succeeded. However, I can't ping from outside to the "online host" PC.

View 2 Replies View Related

Cisco :: Can't Ping From ASA To Host In GNS3

Apr 24, 2012

I test all devices using ping command, from ASA to router was fine (on both interface) but not to Host , and host to router was fine, but only on directly interface(F1/0), and to ASA was not success. am i miss something in my configuration?

View 5 Replies View Related

Cisco :: Can't Ping From Inside To Outside Host?

Jul 6, 2011

configure my Cisco ASA5510 (asa version 8.3.1) so that one of the host (e.g.192.168.8.20) behind management interface can ping to the other host (e.g. 192.168.2.246) behind OUTSIDEinterface. I tried modifying the ACLs, NATs and ICMP statement, but still failed[CODE]

View 19 Replies View Related

Ping From Host To Guest With NAT?

Jun 27, 2012

I have installed an Oracle DB (11.2) on a guest VM (Centos 5) and my host is Windows 7 Ultimate.I need to able to connect to the DB from windows.Ping status is as follows:

guest -> host - IP : Yes
guest -> host - hostname : Yes
guest -> guest - hostname : Yes
guest -> guest - IP : Yes

[code]....

View 5 Replies View Related

Cisco WAN :: Cannot Get ASR 1002 To Ping On Interface To Host

May 12, 2013

I have a cisco ASR 1002 I have plugged a host into an addressed port and the port comes up however the host cannot ping the router and the router cannot ping the host. Neither can router ping its self. I do the same on a cisco 2800 router and it works fine. What's goin on. Is it the fact that this is a ASR router ?

View 5 Replies View Related

Cisco :: 1140 APs - No Ping To Host From Local LAN

Apr 3, 2013

I'm using 3 AP's 1140 with local authentication using local radius (flex connect mode).the radius server im using is MS 2008 R2.authentication is working great on all devices pc's&mobile.authentication method is PEAP wpa2 aes enterprise.after 3 or 4 hours devices loose connectivity to the web.the device seems to be still connected to the ap but there is no ping to host from local lan or any arp learnd on local router.only manual disconnect on device and reconnecting brings connectivity up again.in one case only reseting the AP's worked.

View 6 Replies View Related

Cisco Firewall :: ASA5505 - Can't Ping Inside Host

Sep 29, 2012

I just try to ping a internal Host but it want to go.
 
Laptop<===>ASA5505
 
Connected is the Laptop at Ethernet 0/2 Inside
 
My running-config is a clear config, only VLAN 1 has a IP and Ethernet 0/2 is up.
 
But If I try to ping to the Laptop I get the followed:
 
asa5505# ping 192.168.1.100
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.100, timeout is 2 seconds:
?????
Success rate is 0 percent (0/5)
asa5505#
 
From the Laptop to the ASA5505 I can Ping successfully.

View 6 Replies View Related

Cisco Firewall :: ASA5505 Cannot Ping Inside Host

Aug 2, 2011

I have Cisco ASA 5505  installed  and use as default gateway. I go to Internet through the ASA5505 Here is my Problem.I can not ping from ASA prompt(ASA#) to my Laptop connected to the ASA, but i can ping the ASA inside interface from laptop i can not use ASDM  and the VPN Tunnel is not working between the sie
  
ASA# ping 10.10.10.12
???????????
100% lost 
Laptop c
C:/ping 10.10.10.1
!!!!!!!!!!!!!!!!
 
Here is the Topology
 
INTERNET .<=========================>ASA<===============================> LAPTOP
  
I disabled window firewall on the Laptop , but no goof result.

View 3 Replies View Related

Cisco Application :: 11503 Ping For One Virtual Host

Apr 27, 2013

I have a single  cisco 11503 load balancer.There is a single Banner student information system which is load balanced on it with Virtual ip 10.3.20.101 which is working fine without any issues .I am now trying to add an Oracle ERP application with virtual IP 10.3.20.230 and physical ips 10.3.19.22 and 10.3.19.23 all on port 8003.When I just make the group  ERP-Apps-Grp active , the vitual ip address 10.3.20.230 is pingable , but when I make the  the content Erp_IAT active  it stops pinging. [code]

View 6 Replies View Related

Cisco Firewall :: ASA 5520 - PING From Outside Into Inside Host

May 13, 2013

I have ASA 5520. I cannot ping the host(192.168.1.20) which is inside firewall from outside hosts. Inside host (192.168.1.20) is translated into (198.24.210.226) using static NAT.From outside host, I used "PING 198.24.210.226".  Is it because I used dynamic PAT for inside hosts?

interface GigabitEthernet0/0nameif outsidesecurity-level 0ip address 198.24.210.230 255.255.255.248!interface GigabitEthernet0/1nameif insidesecurity-level 100ip address 192.168.1.1 255.255.255.0

[Code].....

View 3 Replies View Related

Can't Ping / Connect Ipv6 Host On Windows 7 Vs XP

Apr 27, 2011

When I try to ping ipv6.xsnews.nl on either of my Windows 7 computers, it returns "Ping request could not find host". But when I do it on XP, it succeeds. I have tried putting the W7 PC in the DMZ, disabling the software firewall but it doesn't work.

What I think it involves is having ipv6 installed on each. I tried to duplicate the setup of both the XP and a W7 computer, installing the gogo6 tunnel. But apparently it's not setup on this computer because the ping result is the same as on the third computer which hasn't had ipv6 installed. s not setup on this computer because the ping result is the same as on the third computer which hasn

View 3 Replies View Related

Cisco Firewall :: NAT ASA 9.0(2) / Cannot Access Original IP Using Another Port Or Ping From Host

Apr 10, 2013

Basically after upgrade from ASA 8.4 to 9.0 (2) I have problems when certain types of NAT.Example:SA 8.4: nat (LAN, outside) 85 10.252.253.123 source static 192.168.3.2 192.168.3.2 192.168.3.104 static destination service http http In this form the host 192.168.3.2 uses the mapped ip (192.168.3.104) to access by http while other ports can be accessed using the original IP (10.252.253.123).

ASA 9.0:      nat (LAN, outside) 85 10.252.253.123 source static 192.168.3.2 192.168.3.2 192.168.3.104 static destination service http http In this form the host 192.168.3.2 uses the mapped ip (192.168.3.104) to access by http but unlike before now I cannot access to the original IP (10.252.253.123) using another port or ping from host 192.168.3.2.

View 12 Replies View Related

Cisco WAN :: 1941w AP Can't Ping 2nd Router / Host But Interface Reachable

Feb 2, 2013

From the router I can ping the 2nd router, all its host and all of the 1941w interfaces.
 
From the 1941w AP i cannot reach the 2nd router or any of its host, but I can reach the interface that is connected to the 2nd router but only one side of it.
 
Attached are both my router and ap configs. At the moment I am just trying to reach the 2nd router and its host so I can update the AP IOS image but cannot reach the tftp server.

View 5 Replies View Related

Cisco VPN :: 2611xm - Unable To Ping Remote Host Through Tunnel?

Apr 20, 2012

I am in a test environment using an ASA 55005 and a Cisoc 2611xm router. ASA is running version 8.4 and router is running is ios12.4. My VPN tunnel comes up but I am unable to ping between remote hosts. I used the ASDM and SDM for the configuration. Attached is a copy of both configs.

View 8 Replies View Related

Ping Could Not Find Host / DNS And Key-port / Server Not Found

Apr 30, 2011

recently I had some malware on my Windows XP Professional (version 2002), so I followed a guide at Bleeping Computer [URL] to get rid of it. Problem is, for some reason, after I finished, I could no longer access the internet!When I try, FIrefox gives me their "could not connect" message: "Server not found. Firefox can't find the server at [site]." Check the address for typing errors such as ww.example.com instead of [URL]"When I try to log into MSN, the troubleshoot says I have a problem with my DNS and Key Ports.I'm not good with computers so I Google'd and found some ping-ing instructions. When I tried to ping [site], I get: "Ping request could not find host [site]. check the name and try again." This happens regardless of the site I use.Lastly, I tried "ping 127.0.0.1" from a troubleshooting site. It gives me: "Pinging 127.0.0.1 with 32 bytes of data:

Reply from 127.0.0.1: bytes=32 time<1ms TTL=128
Reply from 127.0.0.1: bytes=32 time<1ms TTL=128
Reply from 127.0.0.1: bytes=32 time<1ms TTL=128

[code]..

View 8 Replies View Related

Cisco Firewall :: Unable To Ping Host From Inside Interface From PIX525

Feb 3, 2012

When I tried to upgrading PIX525  6.3 to  7.0 , Not able to Ping the host from the PIX 525 Inside interface  which is on the same subnet,  Also from the host to Inside Interface ,  Tried with Directly connected  laptop with Cross cable and using Straight cable via switch, But the  results end with fail.

View 2 Replies View Related

Routers / Switches :: Ping 10.0.0.1 -t Give Destination Host Unreachable?

Mar 17, 2013

ping 10.0.0.1 -t give me destination host unreachable in the same time when i wright ping 192.168.1.1 -t it give me the correct reply but the net doesnt work

View 3 Replies View Related

Ping - Destination Host Unreachable And Time To Live Exceeded

Oct 17, 2011

when do we get Desteination host Unreachable and time to live exceeded while trying to ping .

From 10.1.1.1 icmp_seq=2 Destination Host Unreachable
From 10.1.1.1 icmp_seq=4 Destination Host Unreachable
From 10.1.1.1 icmp_seq=7 Destination Host Unreachable

View 1 Replies View Related

Linksys Wireless Router :: WRT54G Unreachable Host And No Ping

Sep 26, 2011

I've tried everything that has been posted so far except for opening up the router itself which I will refuse to do.- Getting = Host Unreachable 192.168.1.20 (I am using 192.168.1.1 as the gateway)- No ping whatsoever even when turning on the router over and over.

View 2 Replies View Related

Servers :: Ping Locally / Reply Successful - Destination Host Unreachable

Mar 4, 2011

I am using the window server 2008 and configure tcp/ip properties correct ping locally reply successful when ping localy but when ping yahoo.com then reply destination host unreachable whereas gateway and dns ip is also correct configure so tell me solution about this problem because i am useing the internet.

View 1 Replies View Related

Cisco Switching/Routing :: 3560G Can Ping Devices In Enterprise LAN But Cannot Ping Interface

Mar 31, 2012

I have a new 3560G to set up a small network for a remote site. I configured the vlan and an SVI as the gateway. The switch is also the DHCP server for the LAN. I configured Gi0/2 as L3 port, connecting to the nearest neighbor. My network runs EIGRP so i advertised the routes into the EIGRP process. The switch forms EIGRP neighbors and learns all routes in the enterprise network. The problems I'm having now are: 1. The switch learns all routes in my enterprise LAN and can ping devices in the enterprise LAN, but I can’t ping any interface on the switch from the enterprise LAN. 2.

View 5 Replies View Related

Cisco Switching/Routing :: 4.2.2 Unable To Ping 1 Internet Site From Edge Router Able To Ping

Jan 18, 2013

From My Router that connects to Cable modem i am unable to ping website 4.2.2.2I am able to ping all other websites fines.Same website i can ping from my pc and all other switches fine.Router has only 1 ACL thats for NAT.

View 25 Replies View Related

Routers / Switches :: Windows Ping Success But Mac Ping Fails

Aug 15, 2011

When I ping an address from my windows machine, it succeeds, but when I ping to the same IP on my MAC OS X machine, it fails.

1. Why?

2. How to get successful ping on my MAC machine?

View 1 Replies View Related

Can Ping From Server But Can't Ping To Work Stations

Jan 26, 2012

I installed window server 2003 in a old Pentium III server as a standalone test server. Now I want to use it as a print server and connected it to the domain. I can ping workstations and other servers from that test svr. But i cannot ping that test server from the work stations.

View 2 Replies View Related

Can't Ping XBox 360 But Can Ping Other Devices

Mar 1, 2013

I had both a Westell 7500 and a Linksys Router working fine and had my 360 setup as an extender for Windows Media Center so I could stream TV, Music, Movies, etc from my desktop to the 360. Then I switched my modem/router out with a Zyxel PH5001Z

So now today I noticed that I can no longer find my desktop through the XBox. I have adjusted my firewall settings on the modem itself, even completely disabling it. UPnP is enabled for the 360 and the device is showing under my device table. At first I wasn't able to ping any network devices but after creating an ICMPv4 Firewall rule it worked fine. I've confirmed the XBox IP Address through Network Map, the Device Table on the modem and through Network Settings on the XBox. I've diabled my modem firewall as well as Windows Firewall, completely and I still can't ping my XBox or set it up as an Extender.

I have the XBox connected wirelessly using WPA2-Personal and it's operating in 802.11g/n mode.

View 19 Replies View Related

Cisco :: ACL To Block One Host From Another?

Oct 31, 2012

I am learning to write ACL's along with a billion other Cisco things. The internet is not clear on how to do this exactly. At least in my research.

I have two host on the same subnet and I want to block all except RDP TCP port 3389 from one host to another.

I want to apply that Access-group to a switchport interface on my 3750 that belongs to the computer I want to protect from the other.

Host A: 10.1.1.10/24 -- I need to block all TCP and UDP traffic except for port 3389tcp

Host B: 10.1.1.60/24 -- I need to allow only TCP port 3389 from Host A to this one.

This is on the same switch so I can use an extended ACL like 101 or whatever.

This is almost starting to make sense to me but im still weak on extended ACL. I got basics down pretty well.

View 3 Replies View Related

Cisco :: How To Locate APIPA Host

Jan 25, 2013

I'm receiving a lot of logs on my FW about host cannot receive correct IP address and get APIPA addresses (169.254.x.x).

Is there a way to locate them on network? From my core switch i cannot see them

View 9 Replies View Related

Cisco Firewall :: Two Host With Same Nat On ASA 5505

Mar 22, 2011

I have 2 web servers that replicate between them (two different internal ip). My idea is that if one of them will not work, the other to do the relay.I have a Cisco ASA 5505 I can do a nat for each machine. How should I set ?

View 3 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved