Cisco WAN :: ASA 5505 - DHCP On Outside Interface Keeps Renewing
Nov 21, 2011
I've been running a cisco asa 5505 for quite some time and it has been running fine, now all of a sudden it starts to renew it's outside dhcp adress like every 2 hours. I dont think it's the ISP since I have another device connected also using dhcp to the same ISP and it doesnt renew itself, it's just the ASA. Rebooting it, makes it pick up an adress straight away. The interface seems to be up, the GUI just reports "no ip adress" and then the ASA get's a new IP after about 10-15 min without one. Pressing the renew IP adress button in the GUI throws an error.
View 10 Replies
ADVERTISEMENT
Feb 16, 2011
Started this morning woke up checked my phone no wifi hmm weird checked my hp tpuchsmart connected but jo internet access checked my router(netgear wireless N 300) made sure my modem and all wires are connectedNext went to my router ip 192.168.1.1 after reading some forrums i thought maybe if i changed the ip or sum i would have worked i know dumb though.. any way i believe i disabled my dhcp.. and one of the ip ad on the same page to 192.168.1.3 thats when it got worst i tried ipconfig/release saysNo operation can be performed on bluetooth network connection 2 while it has media disconnected.No operation can be performed on local area connection while it has its media disconnected(Its a wireless connection from my touchsmart to my router) I have tried goin back to the routers page but i can no longer find itI have also tried ipconfig/renew but i get this...No operation can be performed on bluetooth network connection 2 while it has its media disconnectdAn error occured while renewing interface wireless network connection : unable to contact your dhcp server. Request has timed out.No opration can be performed on local area connection while it has its media disconnected
View 3 Replies
View Related
Jan 25, 2012
my RVS4000 is not renewing DHCP lease in Auto mode. Connection lost after 24 hours.
WAN Internet interface is physically connected to cable modem - Motorola SBV6120E. Setup as DHCP server. Cisco RVS4000 is obtaining DHCP public IP without any issue, the problem is that the connection drop every 24 hours and I need to release/renew DHCP each day to be able to communicate after 24 hours. After I loose connection I need to release DHCP, the WAN interface goes down and I need to renew DHCP then. I receive the same IP address and connection is againg UP and working.
tried to load new firmware and also setup the router with default configuration, but without any change. as there is no auto-reboot function, it is really annoying to log into managment interface each day. I also loose remote access after 24 hours, so I am not able to access the rotuer from outside. My local provider do not support static public IP on WAN, therefore I have to use DHCP.
View 2 Replies
View Related
Feb 21, 2010
I have an ASA 5505 configured to get a DHCP'd IP address from the ISP on it's outside interface. The problem I am seeing is when the ISP renews their IP address, the ASA 5505 is still holding on to the old IP address information. I have to either manually renew the IP or reload the ASA. I have the potential of rolling out hundreds of these devices and I would not like my customers to have to reboot their ASA everytime the ISP's DHCP lease experies. I am using an easy vpn autoconnecting to an ASA 5520. Static IP's are not an option on the outside interface of the ASA 5505's.
View 8 Replies
View Related
Feb 25, 2011
I am used to setting up access-lists on outside interfaces with ip addresses that are static. I have recently been given a site that is using a dyndns.org client for name to ip address resolution on an outside interface that is dhcp assigned. I created an access-list to open up ports 41794 and 41795 to an engineering application but everytime I try to connect from the outside I get a syn timeout. The application works when inside the lan. Basically I want to allow outside connections from anywhere on the outside to go to ports 41794 and 41795. I am running a Cisco ASA 5505 on version 7.2(4) Below is my conifg. what I may have misconfigured?
: Saved:ASA Version 7.2(4)!names!interface Vlan1 nameif inside security-level 100 ip address 172.31.2.1 255.255.255.0!interface Vlan2 nameif outside security-level 0 ip address dhcp setroute!interface Ethernet0/0 switchport access vlan 2!interface
[Code].....
View 5 Replies
View Related
May 8, 2012
Is there any way of showing the currently assigned ip address for an interface configured to use DHCP on an ASA 5505?
View 2 Replies
View Related
May 9, 2012
We've just started with the ASA 5505. We do run a DHCP server on the inside interface, so it is in the same VLAN 1 as all of the clients. However, we cannot get it to work.We can't use DHCP Relay, as the ASA 5505 only allows to relay to DHCP servers in a different subnet.Or do we have to move the DHCP server to a different subnet. If so, how would we configure that scenario?
View 13 Replies
View Related
May 1, 2012
I have a Cisco ASA 5505 and I have my internal and external interfaces configured but I currently cannot ping from the inside to an IP Address on the outside. I had this setup and working and I have another set of equirement that I am replacing that is working with my service provider so I know it is a configuration issue. When I ping 4.2.2.2 for example I get:
Destination host unreachable
Do I need to add a static route from my inside interface to my outside interfaces?
: Saved
:
ASA Version 8.2(5)
!
hostname pxasa
[Code].....
View 2 Replies
View Related
Apr 9, 2013
I have an ASA 5510 Try to add a new certifcate to the exsiting trustpoint or create a new trustpoint and migrate my VPNs over to that.
View 1 Replies
View Related
Oct 25, 2011
I have a windows vista SP2 laptop, with an Intel wifi link 5100 adapter and a Realtek PCIe Family LAN adapter. From some time ago, I'm having this issue: each time I want to change network (from my job's to my home's, for example) I have to disable/enable the adaptors. This was not needed for over a year and so I own this machine, and I think It might have something to do with a network drive some IT guy in my new job installed
View 5 Replies
View Related
Apr 2, 2011
I have a problem with ASA5510 CSC10 license renewing. Initially, we had CSC license with 500 seats, and renewed it to 250 seats. After that every time it shows that license expires day before today.(for example if today is 4 April it show that license expires on 3 April).
Clicking on "Check Status Online" didn't work. What can correct this problem ?
View 1 Replies
View Related
May 18, 2011
I have a Toshiba Laptop L10 which was running a bit slow, so I downloaded the AVG PCT Tuneup 2011 package and carried out the various recommended changes including de-fragmenting disc. Now I cannot access the internet via my router and Windows cannot repair the problem as it cannot complete "Renewing your IP address". I have followed advice on this site and implemented CMD re Winsock OK, but the second step "netsh int ip reset reset.log" is not accepted; it simply returns the cursor.
View 14 Replies
View Related
Jan 21, 2013
I configured a Cisco 881 as a vpn-client.When I configure the wan-interface with ip add dhcp , it never gets an IP-address.When I remove the crypto map from the wan-interface , the interface gets an IP-address without any problem.According to examples in the Cisco documentation, I should work; and it works on a 831.
View 3 Replies
View Related
Mar 14, 2013
on the outside interface i cant perform the command ip address dhcp setroute.I get the error: IP and subnetmask form invalid pair indicating broadcast or network address.The commands are there when I do the ? command. It just will not accept the command with or without dhcp.I am trying to test an ASA-5510 as a 4G failover to our ASA-5520. This is Verizon's solution but they did not provide IPs, they use passthru on the 4G modem so I'm trying to set up dhcp. It worked a few days ago. Not sure what Im missing. The IP I got last time from Verizon was 192.168.0.199.
View 7 Replies
View Related
Mar 1, 2011
I have a 6509 with SUP2 w/msfc2 at home, I am currently have dsl for internet with static IP addresses. Due to AT&T not wanting to support faster speeds in my area, I have to look at another option. All of these will be dynamic IP addresses, cable, uverse, etc.
I need to be able to enable dhcp on the wan interface so I can connect directly into one of the gig ports (either on SUP2 or 6316) or on a 10/100 port on a 6348.
I have the following image installed s222-adventerprisek9_wan-mz.122-18.SXF13.bin, according to Cisco's feature tool, it is supported.
I have tried "ip address dhcp" on the interfaces but they will only accept "ip address x.x.x.x", I looked at "ip dhcp" as well and only get the option for "relay".
I would hate to have to put something else in the mix to handle the dhcp portion. I may be keeping the adsl for my mail server traffic and backup in case of an outage on the new provider. So I need to be able to track if a link is up.
View 4 Replies
View Related
Jan 8, 2012
I currently have the managment interface set to my internal network using our DHCP server. We also provide another interface to WLAN for a chartity organization. Their interface and WLAN are locked out of our network (no routes, no nothing) with only VLAN tagging sending out over our backup internet connection. I have been tasked to take over their DHCP scope (255.255.240.0). I added the scope into the 4404 just fine but can't seem to assign it. So, for the sake of argument lets say:
Interface:
management VLAN 10 10.10.10.10 DHCP = 10.10.10.15
charity VLAN 20 192.168.160.2 DHCP = ????
[Code].....
If I tell the charity interface to use 192.168.160.2 for the dhcp scope it errors out. I also tried the DHCP override in the WLAN with no success. If I set either DHCP option for the charity to aim at the managment interface it does nothing as it can't find it..
View 2 Replies
View Related
Dec 27, 2011
I've been using this setting for clients in small offices and what not, and since all they wanted was to give another nutch of security to their network, we've been intalling cisco routers 2600 series still outhere for their internet connections and we had no issues what so ever, not until we run into cable isp provider, and their dhcp wont be able to assign our interface a dynamic IP, this is the setting aplied to the router interface;
interface fastethernet0/0
ip address dhcp
ip nat outside
no ip redirects
no ip unreachables
no ip proxy-arp
Why it wont be seen or assigned an ip by their dhcp, I talked to their isp and they assigned a static ip (private one) and we still have the same issue, if i connect a pix 506e interface with the ip add dhcp assigned to it gets a dynamic ip right away...
View 8 Replies
View Related
Dec 26, 2010
We have a Cisco 886G router connected to the internet. The router receives an ip address. We experience however a problem when the lease time expires. The router does not send a DHCP request to renew it's ip address in time. This causes an interface reset, and connectivity loss, after the lease time of 8 hours.
We are running IOS 880data-universalk9-mz.151-3.T.bin. Config on DHCP receiving interface is:
interface VlanX description To Internet MODEM ip address dhcp ip access-group TEST in!
View 2 Replies
View Related
Apr 21, 2013
i have a adsl modem that is sending dhcp reqeust and i want to use that on my cisco switchs 3560 48 ports.i want to use the interface port 0/48 as a WAN connection and i want to use the other interfaceports for DCHP pool.i have an d-link (dir655) router at home and i want to have the same situation on my cisco switch my WAN interface get from a DHCP reqeust an ip adress from the provider like 10.10.123.44 (for the cisco switch would this interface port gig 0/48)then i want to configere my LAN as a DHCP pool like 192.168.0.1 (for the cisco switch would this interface port gig 0/1 - 47 .
View 3 Replies
View Related
Jul 10, 2012
i have WLC 5508 showing the below Logs , which prevent the users from connecting to the SSIDs , also its disconnecting the associted users DHCP Socket Task: Jul 11 09:54:08.992: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'interface-02'. Marking interface dirty.*mmListen: Jul 11 09:54:08.638: %MM-3-INVALID_PKT_RECVD: mm_listen.c:7671 Received an invalid packet from 10.21.1.25. Source member:0.0.0.0. source member unknown.it shows 3 to 4 times durring 1 hour ,
View 2 Replies
View Related
Aug 2, 2012
I'm running a system that requires a third (and potentially fourth) DHCP server to be setup on each network in my network. The first two devices are Windows DHCP servers serving IPs from different address ranges for failover. The third DHCP is just a listener to receive OS information and device names to be logged in a database.
Currently this works like a charm for my wired clients as I can add in the third and fourth ip helper-address on each vlan and the information is received by the listeners. However, I cannot find anywhere in my WLC5500 to setup these extra two DHCP helper addresses.
The wireless vlan on my layer 3 switch has all the ip helper-addresses, but this doesn't seem to work, and the devices just use the DHCP servers set on the interface in the WLC.
View 5 Replies
View Related
Jan 22, 2013
I would like to configure the 881G to use both the cellular interface and Fe4 WAN port for internet connectivity.Interface Fe4 is connected to an ADSL router.
I have configure each interface with a default route and weighting:
ip route 0.0.0.0 0.0.0.0 Dialer0 200
ip route 0.0.0.0 0.0.0.0 FastEthernet 4 100
I need to configure Fe4 to get an address as a DHCP client:
interface FastEthernet4
ip address dhcp
no shut
duplex auto
speed auto
How do I remove Fe4 from VLAN1? There is some existing config around VLAN 1:
interface Vlan1
ip address 10.73.0.1 255.255.255.0
ip helper-address 192.168.140.13
ip tcp adjust-mss 1400
no autostate
ip sla 100
icmp-echo 10.64.4.15 source-interface Vlan1
tag 3G Keepalive
frequency 10
Then I guess I need to adjust my Internet-IN ACL to allow broadcasts and UDP 67 and 68?
View 1 Replies
View Related
Feb 26, 2012
I'm trying to find out what is the minimum downtime for a Cisco 2800 series LAN interface configured as DHCP client, in order to initiate a new DHCP discover. How much time does it need to take for the Cisco to "sense" the phy disconnection ?
View 4 Replies
View Related
Apr 5, 2012
I've got a new CT2504 controller with software version 7.0.220.0 Regarding to [URL]I've tried to configure the internal DHCP on a dynamic-interface, but this is not possible:(Cisco Controller) >config interface dhcp dynamic-interface vlan401 primary 172.16.x.3 vlan401 Interface IP can not be used as internal DHCP server IP It works, if I use another IP (aka DHCP server) in the same subnet or in another subnet. It works also for the management interface.
(Cisco Controller) >show interface detailed management
Interface Name................................... management
MAC Address...................................... d0:c2:82:xx:xx:xx
IP Address....................................... 10.2.x.135
IP Netmask....................................... 255.255.255.240
IP Gateway....................................... 10.2.x.129
[code].....
View 1 Replies
View Related
May 10, 2012
I'm using an ASA5505 with dhcpd.but i want to assign a specific IP address from the configured dhcp range to a specific PC.Is it possible to bind a specific ip to this particular PC's MAC address.
View 1 Replies
View Related
Jan 29, 2011
When I click on "DHCP Reservation" button in the web interface of the E3000 I don't see any information about the current devices and the reservation list.This problem occurs when my sattelite reciever tries to get an IP address from the DHCP.the name of the receiver is "dream box" (no special characters).I didn't have any problem in the past with my previous router (3COM)Since there are error messages in the page (screenshot is attached), I've tried to use different browsers but the result was the same (Firefox, Safari, IE 8)
View 9 Replies
View Related
Nov 8, 2011
I am looking for a way to bind between a switch interface (cat 3750X) and a DHCP server reply.The switch can operate as the DHCP server .a PC connected to interface Gi 1/0/1 will lways get IP address 10.0.0.1 because it is connected to interface Gi 1/0/1, a PC connected to interface Gi 1/0/5 will lways get IP address 10.0.0.5 because it is connected to interface Gi 1/0/5 and so on... (no matter the source MAC address who sends the DHCP request).
View 8 Replies
View Related
Feb 24, 2013
I have a cisco wlan controller (2100) running software 7.0.235.0. I have the internal private wlan running off of port 1 and that is working fine with an internal dhcp server.Is it possible to setup another ssid (guest) and have the interface directly linked to a static ip on the WAN and also use the built in cisco internal dhcp server?
View 4 Replies
View Related
Apr 14, 2013
I've got a 5505 and I'm getting a DHCP address from a cable modem. How can I show the DNS that the ASA is getting? show int vlan 2 is only givving me the IP and net mask.
View 2 Replies
View Related
May 13, 2012
We recently upgraded our 5505s to 8.2(5) 26 and noticed that each will crash after a cerntain amount of time. Some crash every 30 minutes other will crash every 4 to 8 hrs. The only difference would be the user's home ISP and/or home router, if they have one. They are configured with a dynamic dhcp IP address for the outside interface and the crash files starts with the following:When we downgrade back to 8.2(5) 13 the problem goes away. Any known bugs for this version? I haven't been able to find anything yet. We do have one 5505 that does not have this issues. The only thing that may be different is that it was never at 8.2(5) 13. We had downgrade it from a 8.3 version.
View 2 Replies
View Related
Apr 1, 2012
I'm running a 5505 with DHCP on the outside interface. All 5505 are connecting to 5545.Can I configure the ASA for a site to site to automactically discover the the peer address and automatically establish a connection with 5545?In other words can I configure all settings for the site to site except the peer address. Once connected on network and get outside DHCP, can it also put that address is the peer section of site to site?
View 1 Replies
View Related
May 17, 2013
Well its in this line but do i have to type in a ip even if comcast is giving me a dhcp address?
route outside 0.0.0.0 0.0.0.0 any 1
=============================
hostname asa1
domain-name mydomain.com
enable password rwt5UQJihEq2/Qae encrypted
names
!
interface Vlan1
[code].....
View 4 Replies
View Related
Dec 4, 2011
I am opening a small branch office in another state and the equipment we purchased is as follows:
ASA5505
3560G.
We'll use a site to site vpn but just in case there's connectivity issues I'd like to use the ASA as DHCP. So far I have a scope defined in the ASA and if I plug a laptop directly in I get an applicable IP address. I trunked the port on the switch that goes to the ASA but not the one on the ASA itself (license restriction) The VLAN that I'm using for my PC's has an ip helper address that is assigned to the inside IP of the ASA.
View 5 Replies
View Related
