I have an ASA 5505 with 3 host license.I want to configure 2 outside interfaces and have inside interface. The outside interface going to a separate ISP.Will this work or do I need more licences?
View 3 RepliesI have two inside interfaces (both security level 100) inside and inside110. Inside is 192.168.105.3/24 and inside110 is 192.168.110.3/24. I have a PC on the 192.168.105.0/24 network. I cannot ping the 192.168.110.3 IP of interface inside110.
View 2 Replies View RelatedI trying to allow traffic between 2 inside interfaces with the same security level. VLAN1 and VLAN15. The are on different physical ports on the ASA. I tried to configure this through the GUI Web interface and checked ' enable traffic between two or more interfaces with the same security levels'. With this ASA version, I do not need NAT to allow this, correct?
ASA Version 8.2(1)
!
hostname ciscoasa
[Code].....
I have a Cisco ASA 5510 configured to access the internet, with an:
inside interface (ethernet 0/1) 130.130.0.254 and outside interface (ethernet 0/0) x.x.x.x
I have now configured another inside interface (ethernet0/2) on ASA with the IP 172.16.0.254 and I have connected it directly to another switch with a management IP 172.16.0.5.
The problem is that the two inside interfaces (130.130.0.254 &172.16.0.254) cannot communicate with each other thus the e0/2 172.16.0.254 interface cannot access the internet.
I have an ASA 5505 running 8.2(1), that is configured with three interfaces as follows:
Inside (security 100) 10.0.0.0 /24
Inside 2 (security 100) 192.168.0.0 /24
Outside (security 0) internet
Inside is connected to my internal network, inside 2 is connected to the network of a sister organization, outside is outside.
I'd like to be able to route between from inside to inside 2, and have NAT translate me to inside2's address.
I have inter-interface traffic configured, and when I use a NAT exemption, I can route fine. But the resources on network 2 must see my request as coming from the inside2 interface IP.
My customer is running an ASA5505 with 8.3 code.
The have a somewhat flaky proxy between their inside LAN and the firewall. I'd like to have a configuration as follows:
LAN > Proxy > VLAN 1 (eth0/2) on ASA
and
LAN > VLAN 1 (eth0/3) on ASA
So that in the event of Proxy failure (let's just say it loses power) the eth0/3 interface will kick in.
This appears to be easily configured according to the documentation:
"The following example creates two redundant interfaces:
hostname(config)# interface redundant 1
hostname(config-if)# member-interface gigabitethernet 0/0
hostname(config-if)# member-interface gigabitethernet 0/1
hostname(config-if)# interface redundant 2
hostname(config-if)# member-interface gigabitethernet 0/2
hostname(config-if)# member-interface gigabitethernet 0/3"
But these commands don't seem to be available on a 5505.
I am having big problems trying to get what should be a rather simple configuration to work.I have a Cisco 2901 Router and have setup Zone Based Firewall on this.Traffic from the 192.168.223.x network does not pass through to the 192.168.1.x network.my traffic appears to disappear down the big bucket...Interesting I can ping machine on 192.168.223.0/24 network from the 192.168.1.0/24,So the static routes setup on the router on the 192.168.1.0/24 appear to be routing ok.
View 4 Replies View RelatedI've been trying to figure this one out for quite a while. I currently have 2 inside interfaces (data, phone) and I am moving to 3 inside interfaces (servers, workstations, phones). I have not been able to get any traffic between the interfaces. With the current setup it was not a major problem. With the new setup it will be a major problem.
Below is a sanitized version of the config.
ASA Version 8.2(1)
!
hostname BOB
[Code].....
I have a Cisco ASA 5510 with 3 inside interfaces each connected to a 3750X switch port in a vlan. Outside interface is connected to external router with 209.155.x.x public IP. Static route exists for outbound traffic on outside interface.
3750X is configured for inter-vlan routing. VLANs 10, 20, and 30 have 172.16.x.1 IP address with static routes pointing to the each of the ASA inside interfaces - 172.16.x.254. Connected hosts are configured with gateways pointing to the appropriate vlan interface IP - 172.16.x.1.
Inter-vlan routing appears to be working - I can ping back and forth between hosts on different vlans, and I can ping each vlan IP.I can also ping each ASA inside interface from a host in the appropriate vlan, but I cannot ping internet sites (4.2.2.2 or 8.8.8.8) from hosts on the inside interfaces.
I can ping 4.2.2.2 from the ASA CLI. I can ping internal hosts on vlans 10,20,30 from the ASA CLI. But, no luck with pinging from inside host to internet hosts
Today I run into a problem with enabling ICMP traffice between two inside interfaces on ASA5510 (version 8.2). I tried to ping from 192.168.1.2 to 192.168.2.2 Failed. But I can visit outside websites or ping from any of the two addresses above to 8.8.8.8 So I checked the configuration shown as follow
<omitted>
interface ethernet0/1
nameif inside
[Code]....
I currently have an out of the box ASA5505 and need to change the internal interfact from 192.168.1.1 to 10.20.3.1 so it fits in with the rest of the network.Tried using the ASDM Startup wizard (via 192.168.1.1) and it just seems to hang on "delivering the commands to the device".
View 16 Replies View Relatedi have cisco asa 5505 Security adaptive firewall. my inside network is 192.168.1.0 255.255.255.0 . i want to add static route another network i have that network id is 192.168.2.0 . 255.255.255.0.how i can add the route.
View 9 Replies View RelatedI am very new to Cisco ASA and I am trying many days to implement the design below but still cannot get it done. The situation I am facing is
- a host (e.g. 192.168.5.10) under Inside interface can contact to outside without any problem.
- however a host outside (e.g. in VLAN1 or outside this network) cannot contact host under Inside interface. I am using PING test and always get Request Time Out. [code]
Have a problem in config of my ASA5505 --> I can't access Internet from my new created vlan number 4 (Vlan4):
here my config:
ASA Version 8.4(1)
!
hostname FWWIB1
enable password OEIOH8Zv/vNvif8C encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
[code]....
I'm going nuts with this ASA5505. This is a secondary firewall used only in emergencies when the primary Checkpoint failes.
The basics, it has two trusted interfaces, E0/1 and E0/2-6. E0/1, inside2 has 192.168.01/29 and inside is 192.168.200.1/24. I'd like any traffic to be allowed from inside and inside2 to outside and any traffic from the inside interfaces should be routed. No restrictions should apply between the two interfaces.
inside works just fine but no traffic is going out of inside2, not to outside or to inside.
I have the following config below on my ASA5505, where I want to be able to access remote computers who are VPN'd into the inside network, for support purposes.I want to be able to ping the VPN ip from the LAN, and be able to connect to these computers via the VPN ip. [code]
View 4 Replies View RelatedLet me start by saying that I'm just starting to study for CCNA, so the ASA seems to be a bit above me yet. The ASA's we are using is for VPN to our corporate office and only allowing access to our Citrix environment, so no direct internet allowed. We have a person who works in the remote office who has need for a caption telephone that requires direct access to the internet. The phone only supports DHCP, and getting the ASA to do an ARP reservations is proving difficult. For now I wrote an access list to allow it's DHCP address out but it still isn't working. The access list I wrote is:
access-list 101 extended permit ip host xxx.xxx.xxx.124 any log
access-list 101 extended permit ip any any
access-group 101 out interface outside
When I do a show access-list I'm seeing that traffic is hitting the access list as the hit counter has increased. When I do a show conn I'm seeing one of the IP's that the phone should have access to, however the flags are: saA, so I'm assuming they are not getting a response. According to the manufacturer, only outbound connections are needed, no incoming ports required. All traffic is TCP.
The ASA5505 I am working with has this from the show version:
Licensed features for this platform:Maximum Physical Interfaces : 8VLANs : 3, DMZ Restricted Inside Hosts : 10Failover : Disabled VPN -DES : EnabledVPN-3DES-AES : Enabled VPN Peers : 10WebVPN Peers : 2Dual ISPs : Disabled VLAN Trunk Ports : 0
This platform has a Base license.
Does the Insides Hosts :10 line mean that only 10 devices can be connected to the firewall at one time? I would like to connect an AP to one of the PoE ports and have possibly more than 10 connected. Is this possible with this ASA5505?
I just try to ping a internal Host but it want to go.
Laptop<===>ASA5505
Connected is the Laptop at Ethernet 0/2 Inside
My running-config is a clear config, only VLAN 1 has a IP and Ethernet 0/2 is up.
But If I try to ping to the Laptop I get the followed:
asa5505# ping 192.168.1.100
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.100, timeout is 2 seconds:
?????
Success rate is 0 percent (0/5)
asa5505#
From the Laptop to the ASA5505 I can Ping successfully.
I have Cisco ASA 5505 installed and use as default gateway. I go to Internet through the ASA5505 Here is my Problem.I can not ping from ASA prompt(ASA#) to my Laptop connected to the ASA, but i can ping the ASA inside interface from laptop i can not use ASDM and the VPN Tunnel is not working between the sie
ASA# ping 10.10.10.12
???????????
100% lost
Laptop c
C:/ping 10.10.10.1
!!!!!!!!!!!!!!!!
Here is the Topology
INTERNET .<=========================>ASA<===============================> LAPTOP
I disabled window firewall on the Laptop , but no goof result.
I have an issue accessing the inside network of my church from VPN. This only happens when I connect from my home network. I have no problem accessing inside network of my church if I'm connected from else where (my Clear Hotspot or someone else's house). Here is the hardware detail:
At the church, we are using Cisco ASA 5510 and we have so many VPN tunnels to different churches. At home, I 'm using Cisco ASA 5505. See that attached configuration for my home ASA5505.
I'm trying to make a very plain and simple network with the ASA 5505, I've strated from scratch over a dozen times triyng to find where I'm going wrong. My main goal is to simply create an IPSec VPN connection to my ASA 5505 and simply ping and connect to devices with the "inside network", so far I can easily create and establish a IPSec VPN Connection, but up to this point, I cannot successfully ping or access a single device on the ASA 5505 inside network.I've taken, create the IPSec profile with the ASDM wizard, add exemption for the VPN IP Pool, add access-list from this Cisco link, url...All this and I can't make a single connection to the inside network. [code]
View 7 Replies View RelatedI have ASA5505 configured with internal network as 192.168.15.0 and default gateway 192.168.15.1 From the inside network, i'm able to access internet and able to ping all website (enabled ping). and all internel network devices can ping each other. Except i cannot ping my gateway (ASA5505) 192.168.15.1. I'm continously seeing this message on the log, when i tried to ping.. How to fix this?
Denied ICMP type=8, code=0 from 192.168.15.xxx on interface inside
replace xxx with my network devices that try to ping the gateway..I dont want outsiders ping my gateway, i need ping for inside internal network only.
I want to upgrade "inside hosts" from 10 to unlimited on a ASA5505-BUN-K9, Do I have to buy Security Plus license ( L-ASA5505-SEC-PL =) ) before activating ASA5505-SW-10-UL ?
View 3 Replies View RelatedThe ASA device is going to be the gateway for multiple distinct inside IP subnets. We can have have a unique outside IP address to correspond to each inside IP subnet if needed, but we need some means for a VPN client or a site-to-site VPN to have acess to a pre-definied IP subnet (i.e. if customer A establishes a VPN connection, they have connectivity to IP subnet X; customer B establishes a VPN connection, they have connectivity to IP subnet Y, etc.).Currently, the two inside IP subnets are 10.10.0.0/16 and 10.20.0.0/16. We will be adding more.The problem we are facing is that we cannot reach the VLAN 201 from the ASA we believe this is because. I have setup two addresses on port 0/1 Vlan1, 10.10.20.2 and 10.20.20.1 as an alias. How can we make traffic for the 10.10.0.0/16 subnet untagged and traffic for the 10.20.0.0/16 subnet tagged for VLAN 201.
View 1 Replies View RelatedUsing an ASA5505, have 1 static outside address, want to access an inside SBS-Server on SMTP, RDP (3389), HTTPS and port 987
Have configured network object nat rules using the asdm, SMTP works (I can telnet to the server on port 25 from outside), however for some reason I can not telnet inside and out on port 25, so outgoing mail does not work. RDP does not seem to work from outside, 987 I havent tested from outside. When I try to create a network object nat rule for https I get this message from the ASA:
[OK] object network SBS-HTTPS
object network SBS-HTTPS
[ERROR] nat (inside,outside) static interface service tcp https https
NAT unable to reserve ports.
I am using ASA 5505 firewall with base-license. I connected my firewall to one cisco 3750 switch where i created 5 vlans. I done NATing for all vlans and they able to get internet and working fine. They able to browse all internet sites like gmail and yahoo mail.
All internal users are configured to use Outlook for their webmail. Here the problem is with outlook they are unable to send and receive the mails.
If they directly connected their system using public ip( Directly from ISP) they able to send and receive mails from outlook.
I have installed ASA5505 in the network. Port forwarding has been done for one of the server in our LAN. Public users are able to access the server successfully. I am trying to access from inside using the same Public server IP, but unable to access it. Can I have this feature in ASA5505(I think it is loopback configuration). If so, may I know the configuration detail?
View 4 Replies View RelatedI have been working on a configuration for single IP address (on outside ) of ASA5505.I am trying to utilize the outside address 192.168.0.249 to PAT/NAPT to 10 inside machines [code]
What I am not sure of (actually that could be considered all encompassing) is the mapped services/real services.Any constructive comments assistance?
I am trying to access and ping the inside interface of a ASA5505 from a remote network. From the remote network, I am able to access anything on the local network, but the ASA5505 inside interface.The 2 networks linked by a fiber link which have a transport network on another interface. From the remote network, I am able to ping the transport network interface IP, but I would like to be able to ping the inside interface IP. When I do a packet tracer, I get a deny from an implicit rule.How can I achieve that?
Here are the subnets involved and the ASA5505 config.
Remote network : 10.10.2.0/24
Local network : 10.10.1.0/24
Transport network : 10.10.99.0/24
[code]....
I have a question, it is possible to have two WAN interfaces to configure a cisco 892 router with an ip 255.255.240.0 84.197.167.111 adderess of the first interface and a different ip address 84.197.174.182 255.255.240.0 on the second interface
View 5 Replies View RelatedGot new ASA5550, code 8.2.2 in flash, can't configure "nameif" or "ip address" on the interfaces: [code] These are all the options that I get! Another weird thing I noticed is "<system>" string in "show ver" top line: [code]
View 2 Replies View RelatedI have a cisco ASA 5520 that i'm configuring.From the actual Firewall (with is a linux server), we have the outside interface eth0 with has a public IP and other sub-interfaces (eth0.1; eth0.2,...) with others publics IPs.I'd like to know how I can configure it in an ASA
View 7 Replies View Related