Cisco WAN :: ASA5505 Send Internet To 16 Different Locations Via Microwave Dishes
Jan 1, 2011
I have a 100MB pipe coming.I have one ASA5505. This is the current backbone to the whole system.I want to send internet to 16 different locations via microwave dishes.So, many problem is my pipe is 100 Mbps , want to cut that large pipes into a bunch of small pipes. Per pipe 2 Mbps.So, I can send this B.W ( 100 Mbps ) to 50 Users.
I have only ASA 5505 and L2 switch for Vlan purpose. I heard by using RADIUS server we can do this but I don't know how to do. IF yes, then some Docs regarding that one.
View 2 Replies
ADVERTISEMENT
Mar 18, 2013
i am trying to do EoMPLS using microwave as my Layer 1. i am doing the same thing using Fiber as my layer 1 and it is working. the minute i use microwave its not working. the EVC will be showing as up, but no traffic will be moving. i am using 2 3750Metro series swicthes. i have tries to tweek the MTU to be above 1500 and below 1500 but nothing is working. LDP is establishing, OSPF is working, but the EVC is just not forwadign traffic from end to end.
View 4 Replies
View Related
May 8, 2011
Recently fitted 2 3925 routers on a WAN Mulitlink (2 * 2Mb) which has been working reasonably well but have noticed CRC's and intremitteny up/downs on E1 links. This could be due to issues with Microwave links but on checking nothing stands out on these - no errors or traps form radios.
Anyway taing a closer look at E1 lines and had some questions:-
Microwave radios E1 circuits are set to UNFRAMED, router interfaces set to NO-CRC4, didnt think this was the same?
E1 card are VWIC3-2MFT-T1/E1 and also noticed the following:-
no network-clock-participate wic 0(same for 1 and 2), my card are in slot 0 and 1.
I see no slips etc on E1 controllers .
View 2 Replies
View Related
Jan 23, 2012
How to send videos through internet
View 2 Replies
View Related
Mar 25, 2011
I have a Tp-link wa500g and it won't send Internet across the network, ive recently bought it and I want to connect it to a segam router (sky issues). I've tried putting it in all connection modes but none work. It wont even connect me to the Network. I'm trying to use it as a repeater to extend my network throughout my house without cables
View 2 Replies
View Related
Jan 11, 2011
i am sending emails but they are not being received what do i do
View 2 Replies
View Related
Apr 23, 2013
i have E4310 i want to send sms and use internet with my laptop thorough simcard
View 1 Replies
View Related
Feb 20, 2012
My Linksys router is connected to my desktop and modem and gets internet access but for some reason has stopped sending the wireless signal to other laptops in the house.
View 1 Replies
View Related
Jun 8, 2011
I have installed CSC-SSM-10 on cisco ASA 5520.I am facing two problems
1 : When I send traffic from ASA to SSM module then internet connection becomes slow and sometimes internet session disconnected.
2. When I try to manual update then following erros shows please see attachment .
View 6 Replies
View Related
Jan 26, 2011
I've been having this problem on my desktop and it's really annoying when i try to play online games that need a constant connection.I have Windows XP and i'm using a wireless connection via a wireless USB adapter. The problem is that the internet is running fine but at random intervals it starts to not send or receive any packets. This will usually cause my to disconnecting during a game causing other players inconvenience. After I d/c the internet will usually take 5-30 seconds to start sending and receiving packets again and regain connection.
View 14 Replies
View Related
Jun 6, 2012
I have a Linksys wireless router model WRT54G (not sure the exact model, it's not in front of me right now). It has worked flawlessly for the past several years, but for some reason has recently stopped working. I confirmed it's not a problem with the DSL Modem, as I can hard wire connect to my laptop and the internet works fine. It's clear something is wrong with the wireless router. I've tried unplugging, hitting the reset button on the back, and nothing has worked. My computer is able to recognize/locate the router and connect, it's just that I can't connect to the internet. One thing I've noticed under the wireless connection is that the computer is able to "send" packets, but not "receive." My experience is that this is always the case when I experience connection problems, but I have no idea what that means. I was going to call the Help Line, but I see it costs $30 which is likely more than my router is worth and probably 1/2 to 1/3 the cost of a new one so I am trying to troubleshoot myself.
View 8 Replies
View Related
Jan 31, 2011
Is there any way to get reports on voice utilisation on WAN links so that CAC settings can be proactively managed for each location on our CUCM cluster? Our service provider is advising that this is not possible which means that we rely on customer/staff complaints to recognise where CAC thresholds are being reached. Our preference is to be able to run traffic reports (or the Cisco equivalent) as could be done on our previous (traditional) telephony network and provide additional capacity if and when required BEFORE congestion is reached, thus minimising customer/staff impact.
View 1 Replies
View Related
Jan 15, 2011
I need to keep surveillance on two separate remote locations, each on a different continent. They're both indoor locations and have broadband. One of these setups should be fully bidirectional so I can see them and they can see me, while the other location is unidirectional so I can see them but they can't see or hear me. In both of these farflung locations the people there have the computer skills of your average escargot, so it's going to be a complete and utter miracle if they can even figure out how to boot the PC. I would like to provide netbooks to each location and have them automatically launch a fullscreen webcam on bootup. How to get this set up properly so that it works in a foolproof manner.
View 1 Replies
View Related
Mar 22, 2011
We are facing a major issue of VPN tunnel going down very often. I have 7 Site-2-Site VPN connectivity, this works fine for some days and suddently VPN tunnel goes down intermettenly for one or few locations and i need to clear isakmp sa for that speicific tunnel to come up.When tunnel goes down the vpn phase 1 status.....
6 IKE Peer: 125.18.0.38
Type : L2L Role : initiator
Rekey : yes State : MM_ACTIVE_REKEY
7 IKE Peer: 125.18.0.38
Type : L2L Role : responder
Rekey : no State : MM_REKEY_DONE_H2
After clearing phase 1 for specific tunnel the VPN tunnel come up.
7 IKE Peer: 125.18.0.38 Type : L2L Role : responder Rekey : no State : MM_ACTIVE
CINBLR01-SQDR-FIREWALL-00002# sh version
Cisco Adaptive Security Appliance Software Version 8.0(4)Device Manager Version 6.1(5)
Compiled on Thu 07-Aug-08 20:53 by buildersSystem image file is "disk0:/asa804-k8.bin"Config file at boot was "startup-config"
CINBLR01-SQDR-FIREWALL-00002 up 1 day 17 hours
Hardware: ASA5510-K8, 256 MB RAM, CPU Pentium 4 Celeron 1600 MHzInternal ATA Compact Flash, 256MBBIOS Flash M50FW080 @ 0xffe00000, 1024KB
[code]....
This platform has an ASA 5510 Security Plus license.
View 7 Replies
View Related
Jan 28, 2012
Has a small home network in 2 buildings with 2 wireless routers. He has fiber from the building where the dsl comes into, running up to his house where a second wireless modem is. Both are broadcasting DHCP but I only want one of them to do this. Ultimately I want his server(2008) to broadcast DHCP, but just one of the modems is fine for now.
View 1 Replies
View Related
May 1, 2012
I know how to connect 2 routers in 2diffrent states using internet.Also which service is used for that purpuse
View 1 Replies
View Related
Nov 1, 2011
I'm setting up two separate 5510's at two seperate locations. The client wants two seperate SSL-VPN's; one for the HQ and one for the COLO location. They have a single domain for which I have added a-records to point to the corrosponding ASA's thusly: [code]
My questions is this: do i need to buy seperate certificates for each ASA/fqdn/IP combo? I'm using godaddy to buy the certs. If I do need to buy seperate certs, that makes the installation easier, but may waste $$. If I only need to buy one cert, how do I set it up so that both combo's are verified?
View 2 Replies
View Related
Oct 15, 2011
I have VPN connections in between my HO and branch locations. I am using ASA in HO and 1841 branch locations. One of the location is keep on disconnecting, why this is happening as i can see the configurations are identical to other locations.In 'sh crypto isakmp sa' output i can see multiple entries for this particular location, one with type 'L2L' and others with type 'user'.
View 2 Replies
View Related
May 23, 2011
Firewall ASA5510. I'm planning to get one of ASA5510 for our office in order to secure our network properly, however we have quite specific routing configuration to allow us failover to the remote location (data center) in case of any disaster with our server. I'd like to find out if I can just install firewall between our ISP Ruter and internet and allow traffic to/from Data Centre. In this situation will I have to change routing configuration on Company Router or do I have to do anything with our Company Router
View 1 Replies
View Related
Dec 5, 2011
I have 2 dual ASA 5520 devices running VPN at two geographically different locations. What is the best way to do failover between the two remote locations?i.e. can Cisco GSS / Cisco CSM/ACE be used and if so how would this work.
View 3 Replies
View Related
Dec 17, 2011
I have establlished VPN tunnle between 2 locations
I can ping accros and access server resources on both LANs The problem is that from one location I can not access Internet
I can not ping by IP,when I do tracert it just reaches default gateway of this locations from other location(office) no problem
View 1 Replies
View Related
Jun 27, 2012
I have configured a VPN tunnel between two remote locations using static IP addresses on two RV042 routers. The tunnel seems to work but the problem is that when the two hosts attempt to ping each other only one can successfully ping. One PC with IP address 192.168.1.100 can ping across the network but the second PC with IP address 192.168.2.100 cannot. These are laptops seperate from the intranet used to test the tunnel. Someone had suggested NAT may be the issue so I enabled NAT Transverse on the routers but still no luck. The following is the results from a ping test.
PC 1
ping 192.168.2.1
Pinging 192.168.2.1 with 32 bytes of data:
Reply from 192.168.2.1: bytes=32 time=116ms TTL=63
[Code] ......
View 1 Replies
View Related
Apr 17, 2013
We installed a new ASA 5515 about a month ago for the corporate office we also have 40 branch locations that feedback VOIP, camera, and Citrix to the corp location. Each of the branch locations have a separate DSL connection with a local provider and all of them are dynamic IP addresses.
The problem I have is that I cannot figure out a access rule to make the voip traffic work 100% of the time what ends up happening is five or six random locations change IP address's every day and I could not figure out how to create a access rule for that so I create a static route with that dynamic IP and then it will change a week or so later. That's a horrible security risk and a lot of manual work.
View 4 Replies
View Related
Dec 7, 2011
I have 2 WRVS4400N's installed in our network, one at each end of a VPN tunnel between 2 physical locations. I continue to have issues with the VPN to "Stay" connected, even after purchasing another new WRVS4400N 4 months ago. I can reboot both routers, and the VPN connects with no problem, but hangs up after a few hours / days (no pattern).
I am taking a hard look at the issue now, as about 1 month ago, the newest router "automatically" reset it itself back to factory settings (thus interrupting nearly everything in our network). After contacting support, we reset the router and re-configured it to our environment. It is plugged into a surge protected UPS (yep, I thought maybe a power issue caused the problem, but it's not). Then about 1 week ago, the other/older (9 month old) router lost it's configuration. again, reset it and all works. Including the VPN, but the VPN still works as it did before connects for a while, but then drops and generally I need to reboot the router to get it connected again (clicking on the Connect on either router doesn't work until after a reboot).
Also, in light of the recent "lost configurations", I turned on logging and now I'm getting TONS of emails of log activity, even when the network is idle (no users, no background jobs running).
after rebooting and no inter activity, I get this kind of log, all night long (to me it generally looks like the VPN connection resets and increments by 1... I'm taking a guess that the increment hits a limit someplace and I lose my VPN).[code]
View 6 Replies
View Related
Jun 28, 2011
I have 3 different office location and I need to set up a LAN so that all three are connected and can share info?
View 1 Replies
View Related
May 7, 2011
I setup one location (business retail shopping center) in maryland (using swann dvr/cameras- will switch to qsee) with no internet available.I setup another location (business auto shop) in virginia (using qsee dvr/cameras) with internet through verizon fios.I have internet through cox at home in virginia which I can view cameras remotely only to one location in virginia.
View 2 Replies
View Related
Jan 26, 2011
We purchased a database program which has 3 licenses attached. This is a small non-profit org. We would all like to be able to use the program from our homes. What is the best way for all to share and update data to the same database? Would we all be able to work on it simultaneously?
View 2 Replies
View Related
Feb 6, 2013
why one of my two offices experiences significantly slower speeds when accessing the web. I'm a complete technology simpleton, so I haven't been able to figure out a logical reason for it. Here's the scenario:
Office 1..................................................Office 2
==========..........................................===========
Comcast Business.....................................Comcast Business
tests at 33 mbps down..............................tests at 7 mbps down
tests at 6 mbps up....................................tests at 3 mbps up
6 CPUs access Linksys SR216 10/100 switch..6 CPUs access 3Com Office Connect Ethernet Hub
switch accesses Comcast modem.................hub accesses Comcast modem
My laptop, and all other CPUs, perform significantly faster at Office 2.
Is it the difference between the switch at Office 1 v the hub at Office 2? I always thought they were sort of the same thing. I know I've taken some of the cables out of the switch in Office 1 and put them directly into the Comcast Modem and haven't seen any improvement.
Why on earth does my laptop perform so much better at Office 2. I've also moved desktops to Office 2 and they are noticeable faster at that location as well. I'm stumped. We access a major company's web site for account servicing, and it is twice as fast at Office 2...while using the exact same laptop.
View 3 Replies
View Related
Jun 21, 2011
I work as a systems administrator for a global company and currently right now all my end users which is roughly 300 all use VPN from there office location to dial back into the server or use terminal server. I would like to know how to connect there locations back to main site without using VPN. What would be the cheapest and or easiest method to complete this.
View 1 Replies
View Related
Dec 2, 2011
I set up a network drive in my computer that links to an FTP directory on my server.... However all the jpg files are showing the default jpg icon. I want to see a thumbnail of the actual image if possible. Im running windows vista and windows 7. Same issue on both. Also, I tried hard to change the network drive .ICO file.... Tried creating a shortcut and doing it that way.. still no luck.
View 1 Replies
View Related
Jul 24, 2012
I have a small home with two clusters of 2-3 devices which use the Internet - one ground floor, south corner, and the other top floor, north corner. I have a wireless router (Netgear N750) in the ground floor south connected to my cable modem. All devices in the area of the existing router are plugged into it (Cat5 cable). The devices in the top-north corner use wireless to communicate with the down-south router.
Running cable drops is not in scope for me, as we have a finished basement and I would have to blind drill horizontally across 50' of flooring and joists.
Tried running cabling through heat vents using a wireless camera mounted to a cable puller and all I did was discover some areas of my home that appeared to be four-dimensional. Attic not accessible in locations required for cable drops.Tried powerline devices and performance was much worse than wireless - I know that's a major YMMV situation but the Netgear ones I tried had like 5 Mbps connection rates. I also could not connect from other outlets - I have read if you had electrical work installed and have new lines run it can impact powerline performance. That may be the case in my home.
My questions:
A. I have OK to poor signal strength in top-north and top rate is ~ 150 MBps off what is supposed to be 300N router. Would I get better performance if I installed a wireless router in top-north and connected the top-north devices to it? Down-south performance is fine so it's not the cable modem/internet connection.
B. I believe I'd set top-north router up as a wireless client. I've experimented with Tomato and DD-WRT but don't know how to evaluate. Any tradeoffs I should know about?
C. Any networking changes I should consider if I go with such a topology? (MTU, who does DNS, etc). Currently use router as source for DHCP and DNS lookups. Should I limit which router wireless devices may connect with?
View 1 Replies
View Related
Oct 3, 2012
I am not a ASA expert but I have configured them few times. I have a vision of a task I have to complete but not sure if it is practical or how to go about doing it.
We two locations, Location A and Location B. Both locations have a 100MB internet conection. Location A has a ASA 5510. Location B has a 5505. Users at both locations access the internet via their respective ASA. Location A is the headquarters and Location B is a disaster recovery site. We want to setup a tunnel between both ASAs. This tunnel will be used to replicate data between the two locations for DR purposes. We need the users to still use the same pipe to get to the internet but want to allocate 10MB for internet use and the remaining 90MB for the DR tunnel.
View 30 Replies
View Related
Oct 19, 2011
I want internet for the clients behind the ASA. When i made an entry like:
object network as-us-db11_internet
nat (inside,outside) dynamic nat_usa_pool_72
access-group inside_access_in in interface inside
access-group outside_access_in in interface outside
then have the computer internet but the Client vpn connection wont work. i can not connect to the computer over vpn. but vpn connection worked.
View 1 Replies
View Related
