I want to know what the default behavior about the command 'mls qos trust dscp' under router platform interface. the router is ASR1000 series.we don't need to put above command line to trust dscp in case of router? otherwise, we have to add it as welll as like switch platform.
View 4 RepliesI have a problem with the command mls qos trust dscp, I used the ios c2800nm-ipvoice_ivs-mz.124-25f.bin but i can not enable dont show me the complete command in the interface Ethernet o Giga. I want to configuring mls qos trust dscp.
View 1 Replies View RelatedI am reading through a QOS Document and they want me to trust the DSCP value from an IP phone (Siemens) but UN trust the PC DSCP value. How can I trust one thing but not the other? I am using a 2960 Cisco switch with IP base IOS.
View 2 Replies View Relatedi have Catalyst2950SI with iOS12.1, connect a wifi-access-point to f1/1(dot1q trunk port),and connect another L2SW to f1/2(dot1q trunk port),and IP phone, MobileCamera connects to wifi-access-point,IP phone has dscp=40 value on its own packet,but MobileCamera doesn't have any dscp value or cos.now, i wanna do QoS by that dscp, So i type as below,
interface 1/1
switchport mode trunk
mls qos trust dscp
interface 1/2
switchport mode trunk
mls qos trust cos
i would like to know the possibility to use mls qos trust dscp with service-policy in the IOS ver.12.2(25)SEE2.The specific version is not possible to configure like below.
Cat3750(config-if)#do sh run int f1/0/1
Building configuration...
[code]....
Any equivalent show command to get the "FIB TCAM Usage" on An ASR 1006 ?the "show platform hardware capacity forwarding" does not work on ASR1006 Example on 6500: Router# show platform hardware capacity forwarding.
View 1 Replies View RelatedDuring WAN troubleshooting, I did a "clear interface ser0/0/0" on a branch router. It has two WAN links. I lost ssh/telnet connectivity but both WAN links were still replying to pings. We did a manual power off of the router to regain connectivity.Is there a known issue with this command on this IOS version? We're using Cisco 2911 platform with IOS 15.1-1.T2 version.
View 1 Replies View RelatedHow the dscp-cos or cos-dscp mapping takes place in c892 router? There is no command like "sh mls qos maps" in c892 like we have in c2951 or c3925.
View 3 Replies View RelatedThe ASR1000 router supports hot-swap modules and network interfaces?
View 2 Replies View RelatedI currently have a 50Mbps Internet Connection provided by an ethernet handoff for hosting some webservers. We are looking at adding an additional 10Mbps Internetn connection and route BGP between the two. For the 50Mbps connection, i'm using a Cisco 2951 router. I also have another 2951 router to terminate the 10Mbps connection. Does these router have enough horsepower to fully route BGP?
View 1 Replies View RelatedI have a problem with dscp preservation on a WS-C3750X-48 catalyst; in my little diagram, his name will be SW2, so I have this:SW1 <-> SW2 <-> RT1. some phone connected to SW1 mark with dscp EF (46) the voice traffic.The "mls qos" was enabled on SW1 and SWt. The interlink switch ports has the "mls qos trust dscp" option, the phone port and the router port also.And the problem is I can see the dscp marking on the SW2 when I span the voice vlan on this switch but the dscp was removed ( DSCP set to 0) on the router port ( span on the router port for look )If I made also a packet capture on the router RT1, I see the DSCP was effectively reset to zero.If I disable the "mls qos" on SW2, of course all is fine and the dscp was preserved and forwarded to the router. [code]
View 2 Replies View RelatedI am working on a network which has two ISP connections (Active/Active) terminating on router (ASR1000). From the LAN side (6500 switch) all the traffic need to be route on ISP1 but some of the specific subnets like 10.250.0.0/16 need to be route on ISP2 connection.
I am planning to use PBR and NAT with route maps. any documents or refrences are provided.
(access switches)---------(core switch)----------(routers)----------------(ISP1)
----------------------(ISP2)
How to trust the transit CoS value on ASR1013?
Tried so:
Router# configure terminal
Router(config)# interface gigabitethernet 0/0/0.1
Router(config-subif)# encapsulation dot1Q 1 native
Router(config-subif)# plim qos input map cos enable
But not worked.
Traffic path without ASR:
Server --> DLink 3526_1 --> Cisco 3750 --> Cisco 7606 vrf VoIP --> DLnk 3526_2 --> Client
DLink 3526_1 sets the CoS = 5
Client receives CoS = 5
If we add ASR1013:
Server --> DLink 3526_1 --> Cisco 3750 --> Cisco 7606 vrf VoIP --> Cisco ASR1013 --> Cisco 7600 global --> DLink 3526_2 - Client
DLink 3526_1 sets the CoS = 5
Client receives CoS = 0
We are trying to set up ACS 5.2 in our multi-forest AD environment. As part of our evaluation we set up an Active Directory External Identity Store to a domain (a.b.edu). It connects properly and I can see the directory groups in the that tab when we Select. This domain (a.b.edu) has a two way trust with another domain in another forest (x.y.b.edu). However, I do not see the groups in that domain and I cannot seem to manually add those groups using the Add on the free text Group Name.
The documentation is not clear on this point: Page 8-41 and 8-42 of the "User Guide for the Cisco Secure Access Control System 5.2) says: "The External User Groups dialog box appears displaying a list of AD groups in the domain, as well as other trusted domains in the same forest." This implies to me that it cannot cross forests even though a trust is set up. This seems to be what is happening.
Am trying to find out what is the suitable SPA for ASR1000 routers to connect ATM DS3 through the local telco. Currently this is connected to a NM-ATM-DS3 module on a C3845 router. The reason for asking is we need to upgrade the WAN router to ASR1000.
View 2 Replies View RelatedI am looking for a way to use a 3G connexion on ASR1000.Is it possible to install HWIC module of ISR2 in SPA slot or use an USB modem on the RP?
View 2 Replies View RelatedThe ASR1000 router supports hot-swap modules and network interfaces?
View 1 Replies View RelatedWe use ISG on asr1000 (l3 routed subscriber). Now we are trying to implement ipv6 isg sessions. so.. for ipv4 sessions we have
radius-server attribute 8 include-in-access-req
radius-server attribute 32 include-in-access-req but for ipv6 there is no such attribute#radius-server attribute ?
11 Filter-Id attribute configuration
188 Num-In-Multilink attribute configuration
218 Address-Pool attribute
25 Class attribute
30 DNIS attribute
31 Calling Station ID
32 NAS-Identifier attribute
4 NAS IP address attribute
44 Acct-Session-Id attribute
55 Event-Timestamp attribute
6 Service-Type attribute
60 CHAP-Challenge attribute
61 NAS-Port-Type attribute configuration
66 Tunnel-Client-Endpoint attribute
67 Tunnel-Server-Endpoint attribute
69 Tunnel-Password attribute
77 Connect-Info attribute
8 Framed IP address attribute
95 NAS IPv6 address attribute
list List of Attribute Types
nas-port NAS-Port attribute configuration
nas-port-id Nas-Port-Id attribute configuration
what is best practice for authorize ipv6 l3 subscribers ?
We have asr1006 with 2 esp-40 and 2 rp2 and 2 sip-40. we need to bridge vlan from portchannel (2*10) to single 10ge port.
So fn said that EVC on Port-Channel supported on our software and document [URL] have such example
- configure terminal
- interface port-channel channel-group
- service instance id ethernet
But on our router we have not service command on port-channel. only on non portchannel interface.
But other document have Restrictions for Configuring EVCs on the Cisco ASR 1000 Series Router The following features are not supported: EVC on Etherchannels
Connect ww port-channel 1 2 tenGigabitEthernet 0/1/0 2 this is possible command on our router (but i can't create service instance on portchannel interface)
We need to bridge l2 without l3 termination ? is this possible with port-channel ?
we're trying to integrate our SBC instances (CUBE SP on ASR1000) into our network management system (EMC SMARTS)Syslog messages from SBC instances are some kind of cumbersome with lot of line breaks resulting in multiple syslog messages the NMS must parse.How do I configure it to just put it all into one line just as "normal" log messages?
View 2 Replies View RelatedI have a question regarding netflow and NAT. I have read some documentation (on ASR1000) regarding monitoring NAT process on Cisco ASR1000 that can be done using netflow version 9 (the term was called netflow event logging a.k.a NEL). The problem is, I have not found the netflow collector that can do that. I have queried several software such as manage engine "Netflow Analyzer" and Lancope, but they said their software can not do that.
View 11 Replies View RelatedHow to test the aaa on cisco asr 1000 ? I wana test some user account to a cisco acs.
View 5 Replies View RelatedI have a question which i am unsure of, on the 6500 i know i can set mls qos trust to cos or dscp since I don't have any trunks configured on that switch that i want to trust cos most of my ports trust dscp instead. The question is will packets coming in or going out at L3 with the TOS bits set get placed in the correct in/out queue. For example if a packet comes in on a port with a mls qos trust dscp and has the TOS set to XX will this XX get mapped to the correct COS value based on the default dscp to cos map and end up going out the correct queue which handles that specific COS number?
I mainly asked this because i saw the following on the cisco site and again i am suing dscp trust and not cos.
Weighted Round Robin (WRR), Deficit Weighted Round Robin (DWRR) and Shaped Round Robin (SRR). WRED and all the Round Robin scheduling options use the priority tag (CoS) inside an Ethernet frame to provide enhanced buffer management and outbound scheduling.
I applied command "auto qos voip trust" to the uplink interface. But I found that the interface shown command "auto qos trust" was applied when i show running-config. Could the command "auto qos voip trust" show in the configuration after i applied? If not, how can i check the interface that applied "auto qos voip trust"?
View 5 Replies View RelatedI'm trying to use EPC on ASR1001 running IOS-XE 3.4, and it won't work. Configuration commands are accepted by the router, but there are no packets in the capture buffer.In release notes for IOS-XE, in the 2.5 section, there is a statement that EPC is not supported on ASR1k. Is it true also for newer versions of IOS-XR?
View 1 Replies View RelatedOne of our customer would like to connect 3 datacentres and decided to use VPLS to extend layer 2 VLANs . For this purpose they have bought six Cisco ASR1000 edge routers( two at each side).They also wanted to buy MPLS SP backbone but have decided to buy 2x10G dark fibre links instead.My question is,
1-Will it still possible to run VPLS over dark fibre? Because all the documents I read regarding VPLS are deployed over MPLS backbone.
2-Any sample configuration for implementation VPLS in ASR1000 ?
how the ASR1000s are being setup.I am looking at ASR1000s as part of network refresh and was looking at RJ-45 based Gigabit Ethernet ports compatible with the ASR1000s SPA-5X1GE-V2 seems to be an option but they are all SFPs. Are there any options for RJ-45 ones on ASR1000s?
There is an option for the 2 port where one can mix and match SFPs and RJ45 but I was looking for something which is RJ45 only.Are there any options for them available.I know I could get something with FastEthernet type but was looking for the GigabitEthernet type.
I'm trying to find out what platforms support Multilink PPP with Link Fragmentation and Interleaving over a single link, when that single link is PPPoE. In searching the documentation, the best information I can find is that it seems to be supported in one direction on the ASR1000 url...Many platforms appear to support PPPoE and also MLPPP w/LFI, but it's not clear that both features are supported on the same link.
The application is a radio that has an Ethernet interface on its terrestrial link, and acts as an Ethernet bridge. Would like to use Multilink PPPoE with LFI in order to provide LFI in order to run VoIP over lower speed links (e.g 256kb). For what it's worth, the radio also supports RFC 5578 PPPoE Extensions for Credit Flow and Link Metrics. It was fairly easy to find what platforms support RFC 5578. But RFC 5578 would be used to support variation in the capacity of the link. If the link speed is fixed, RFC 5578 is not needed. I was trying to find if the set of platforms supported increase if the need for RFC 5578 is taken off the table.
In particular, I'd be interested in the whether the ASR 9000 series supports MLPPP bundles with LFI when the links are PPPoE.
We're installing ASR1000 series (ASR1001 and ASR1006) routers on a new WAN and have a requirement to enrypt the traffic between the EIGRP neighbors. Each ASR will be connected to the MOE with a gig interface and we will be using L3 on the interfaces with EIGRP as the routing protocol. We have advipservices-k9 IOS-XE
The ASR1006 is our datacenter WAN router and all remote sites have the ASR1001s. The ASR1006 WAN interface will be configured with L3 subinterfaces, one to each remote location, using a /30 mask.
What is the best method to encrypt the traffic between the ASR1006 WAN interface and the remote ASR1001 WAN interface?
I have a computer connected to a domain trying to login and I got this error message "the trust relationship between this workstation and the primary domain failed"
Then I tried to login as local Administrator and after trying a few passswords get this error. Your account has been disabled.. please see your system administrator
We have QoS configured throughout the company, but the standard config we have applied across the 3750 switches only includes the below: We have IP phones (not cisco) attached that are marking with EF, and the PC is an untrusted end device (so needs to be by default marked as zero).Is the above enough to trust VOIP DSCP EF without resetting it to DSCP 0, or do I also need to add a trust line (i.e.: mls qos trust dscp)?
View 2 Replies View RelatedAre there any differences between the autoqos commands on a WS-C2960S switches (or in any other series)? Follow the commands:
- auto qos trust
- auto qos voip trust
I was checking the documentation on this link:
URL
And couldn't find any great difference between the two commands, as far as I could see they'll set the Ingress and Egress queues the same way.
Are there any differences between those two commands (auto qos trust and auto qos voip trust)? If so, when should I use one and the other?
When attempting to log in to a computer (running Windows 7 Professional) here at the office using the network administrator account, I get the error message: "The trust relationship between this workstation and the primary domain failed." I wasn't here when this laptop was set up, and so I don't know if any local user accounts were made or what their passwords would be if they were there, so I can't think of any way to log in to the machine and disconnect/reconnect to the domain which is really my only idea on how to fix it. Finding out what would cause this to suddenly start happening would also be nice, but mostly I just need to figure out how to get reconnected so I can get this back up and running.
View 1 Replies View Related