Cisco WAN :: Configure New Routers 2921 And Modules
Sep 3, 2011
I have a plan to replace the old routers which are EOL/EOS and i configured the new routers(2921) and modules in Cisco configurator, But i'm stuck with IOS feature set.Old routers are running with IS-IS Protocol, which IOS feature i need to select under 2921 to get the IS IS feature.
configuring up a 2921 router for remote site which is fitted with 24 port Etherswitch module.As part of this setup I have defined 3 vlans on the router, but when I go onto etherswitch and for example set switchport access to access vlan 3 it is not aware of this vlan.Do I have to set up trunk inbetween Router and its etherswitch?Wish I had ordered seperate switch as it would have been easier or am I missing something.sho vlan-switch shows my vlans but on swicth sho vlan brief does not.
I have 2921 router and I have 3 very basic switches that I need to connect to the router. The switches have very basic default configurations and there is no way to edit them, so I only have one VLAN and one default gateway. I can't assign the same IP address to each LAN port. I'm not sure how to make this setup work.
I am not able to configure Service policy output command in Cisco 2921 router.While configuring I am getting below error.Same config is working fine in Cisco 3845 router.I am suspectting the problem with license in IOS.
I have a lab setup and I want to test a point-to-point connection between two 2921 routers in a lab environment, without going through an ISP. I have a HWIC-1DSU-T1= in each of the routers. I have already configured ip addresses to the router interfaces, eDo I need to set any CLOCK RATE or BANDWIDTH commands or anything like that, since my traffic will not actually be going through an ISP during this lab test?
I have one cisco 2851 router and one watchguare firewal currently being used as the main router. I want to connect the cisco as a secondary router on the same network.
Is it possible to install Content Security and Control (CSC) Modules on ASA 5505 ? Or only AIP SSC-5 Modules are the only modules that can be installed on ASA 5505s ?
Using ES2 enhanced etherswitch modules? Could not find out whether it functions identically as NM-16ESW or not. I do understand that ES3 module act like a separate device connected to the router chassis via internal interface and has its own configuration file and processor resources similar to older NME-16ES modules. What about ES2 card (e.g. SM-ES2-24)? Does it work as separate L2 switch connected to the router chassis via trunked internal interface or integrates to the router like the older NME-16ESW module did? Is it possible to turn its ports into the routed mode (no switchport) and use them for L3 forwarding with routing protocols such as OSPF?
In a 6500 or 7600 a 'show module' gives a run down on all the modules in the slots, their HW and SW versions and status. But I can't find a similar command in the ASR1006.
Looking for a show command to display the actual physical Ram modules inside a 2911 router. I believe they come with 2x ram slots and I need to know if it has 1 ram stick or 2.show version displays the total amount of ram, but not if its 2x128 or 1x256 etc.This is also production gear so I cannot open it up and have a look until the scheduled downtime.
We had some issue with Datacentre ACE modules. Both primary and DR ACE modules got restarted in 16 hours difference. Unfortunately Syslog was not configured on the ACE and local logging got cleared after restart. The current IOS version is A2(3.2). The modules uptime was around 300 Days. Here is the log from 6509 switch during the restart. [code]
I want to collect the logging messages about the saa5525x IPS events from devices to a server running a syslog daemon, and I have no necessary to collect any other logging messages about the firewall, how would I config the configuration logging?
i m looking for asa 5550 product.Part # ASA5550-BUN-K9 - Cisco ASA 5550 Appliance with SW, HA, 8GE+1FE, 3DES/AES
1) does 5550 contains built in CSC / IPS modules.? why i m asking because the "quick refrence guide " indicates that expansion slots are not available.
2) can asa 5550 natively protects natively against networks attacks against virus / worms etc with out CSC OR IPS MODULE.?
I recently purchased a Cisco 5508 WLC and I'm looking to buy some SFP modules but can't find info on which ones would be compatible with the controller on Cisco's website . Is there any module that can support 10Gb as I have a 10Gb on the other end (switch end)?
I had already posted for voice modules for cisco 2811 but not able to find it. But here are a few questions regarding i
1. I am trying to configure a cisco 2811 with FXS ports . I am using an NM-HD-2V with a VIC3-2FXS. I am using the right modules. Also I believe we need PVDM mosules installed in the NM-HD-2V. We have PVDM-12 modules. Will that work or is 2811 compatible only with PVDM2-xx modules.
2. We are also trying to configure a cisco 2811 with PRI port. We plan to use an NM-HD-2V and a VWIC-1MFT-T1/E1. If they are correct and if we need only PVDM2-xx modules.
3. Also we are trying to configure a cisco 3845 with PRI and we plan to use the same as in 2811 that is NM-HD-2V, VWIC-1MFT-T1/E1. And here also we are not sure if we need only PVDM2-xx DSP modules.
I've seen a lot of things I want to and need to fix to get our network more secure but my first order of business is Visio diagrams of the old network and projected diagrams of the new network when we move to our new DC next Saturday. I've made maybe 1 diagram on my own thus far and have edited a few. I want to create physical and logical diagrams but I'm not quite sure what to include and what not to include on either since I haven't seen a wealth of diagrams up to this point in my career.
1st question: Does anyone know where I can get visio stencils of IPS modules for ASA 55xx series? Didn't see them on Cisco's stencil site or with a google search
2nd question: Our network is setup like this... A stack of 3 3750s act as our "Core" and have a 2 port etherchannel to every layer 2 2960 switch (15) in the network. In a physical diagram, 30 links would make it a little busy, hell even 15 links represented as the etherchannels would be busy
Is there any option available in any of the Cisco ASA55xx series model to install both csc-ssm and aip-ssm ips modules ? If, so is it advisable to install both ? Is the throughput of ips module has any dependency with the asa chassis throughput ?
I am experiencing an issue with end host being discovered on a cisco 4510. Anything connected to modules 9 or 10 are not discovered in User Tracking. The switch is running: Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSALK9-M), Version 03.02.01.SG RELEASE SOFTWARE (fc4).
I would like to know if any additional power would be needed for a 3845 (currently with one (1) NME-XD-48ES-2S-P) to which another 24-port switch module is added. Thus, I would have two (2) switch modules on the 3845 for a total of 72 ports.
I have been unable to find specific power requirements detailing the requirements with 1 ethernet module, 2, etc.
We have a 6513 which had 2x 8port (WS-X6708-10GE) 10GB modules one in slot 10 and another in slot 12. Between this two modules we created a 4 port trunk 40GB (2 ports in each module) between the 6513 and a Nexus 7018. Yesterday we swopped one of the moduless for a 16 port 10GB (WS-X6716-10GE) and cannot trunk between the two cards. Only 2 ports work in either one or the other. Seems because of the difference between them (DFC3CXL & DFC3C). Taking a look at the logging we noticed something to the fact of incompatability QOS feature between them.
I have 2921 with SEC feature set ( version 15.0(1)M4 ) and want to configure l2tp tunnel, LAC to LAC scenario. It does't have pseudowire-class command. Does it require another license or commands ?