Cisco WAN :: High CPU Utilization On 7206VXR
Jan 7, 2013High cpu utilization on cisco 7206 vxr router.[code]
View 2 Replies
ADVERTISEMENT
Cisco WAN :: High CPU Utilization On 7206VXR (NPE-G1)
Jun 20, 2012I am observing very high CPU utilization on my Cisco 7206VXR (NPE-G1) Router. We have done all the necessary troubleshooting but not able to identify root cause. [code]
View 10 Replies View RelatedCisco WAN :: High CPU Utilization On 7206VXR Due To Traffic?
Apr 19, 2011I have a 7206VXR router doing policy routing with CEF enabled on all interfaces, no Cache Misses, Align Errors or failed buffers. CPU peaks up to 80% every two or three minutes. I suspect it is traffic related as I have a standby box and when it becomes the active on in the HSRP pair to high CPU load and LAN interface input errors follows it. see various show command output below. The router has a NPE-G1 and I'm using a gigabit port off of this on the LAn side and a E3 Frame Relay interface on the WAN side.
UK-DHC-Policy1#show buffersBuffer elements: 1118 in free list (1000 max allowed) 3539658545 hits, 0 misses, 1119 created
Public buffer pools:Small buffers, 104 bytes (total 50, permanent 50, peak 229 @
[Code].....
Cisco Switching/Routing :: High Cpu Utilization On 7206VXR / NPG-1?
Mar 19, 2013Cpu always hitting 70% to 80 % and interrrupt traffic is 70%. Want to know the root cause for this issue.
CPU utilization for five seconds: 73%/65%; one minute: 71%; five minutes: 67%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
1 8 59 135 0.00% 0.00% 0.00% 0 Chunk Manager
2 58864 3290773 17 0.00% 0.00% 0.00% 0 Load Meter
3 1784 238001 7 0.07% 0.01% 0.00% 2 Virtual Exec
[code]....
Cisco :: LMS 4.0.1 - High Memory Utilization
Oct 12, 2011What causes LMS 4.1 to have high memory utilization?
View 4 Replies View RelatedCisco WAN :: High CPU Utilization On 7606?
Sep 28, 2012Our Router 7606 is in a problem with high CPU Utilization. We are using one EBGP and one IBGP session. We are also running OSPF with area 0 between two IBGP router to exchange few local networks. When bandwidth cross 100 MB than only CPU use become 100%. when bandwidth consumption is 80MB CPU use become 80% end so on.
Out put is when bandwidth consumption is 34MB
CPU utilization for five seconds: 44%/43%; one minute: 42%; five minutes: 30%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
78 44 9625 4 0.39% 0.03% 0.00% 2 Virtual Exec
13 40 375 106 0.07% 0.00% 0.00% 0 ARP Input
30 116 1098 105 0.07% 0.01% 0.00% 0 IPC Seat Manager
[code]....
Cisco :: High CPU Utilization On 7609-S?
Aug 10, 2011I have a hight CPU utilisation problem in my CISCO7609-S routers. the cpu utilisation can rise 99% et this is usually. In the moment of hight CPU the the process CPU give the following:
the show processe cpu history give: show version
Cisco WAN :: 2811 High Cpu Utilization
Apr 29, 2013I have a 2811 that is really hitting the CPU hard. Nothing shows on CPU processes. It has an IPsec VPN tunnel back to HQ which also has a 2811 that terminates the VPN. The HQ has 2-3 IPsec tunnels to other remote sites. The CPU at the HQ avg 50% utilization during business hrs, peaks at about 80%. The remote one is very high 95% peaks, avg 80%-95% during business hours with bandwidth utilization of only 10-20Mbps. I read somewhere that its possible that fragmentation could be causing this. My question is, if I set the MTU to 1450 on the remote, I am guessing I will need to do all the other routers as well, the HQ and other remote sites? Siince they use the same outside interface to my HQ, is that correct?
View 3 Replies View RelatedCisco WAN :: CPU Utilization High In 2811
Jun 23, 2011We have Cisco 2811 router and facing high CPU utilisation as 70%/67%;,IOS Runing :c2800nm-advsecurityk9-mz.124-3f.bin.
View 4 Replies View RelatedCisco :: Prime 4.2 - High CPU Utilization
Dec 4, 2012I am running Cisco Prime 4.2(UNIX version) on a VM. CPU utilization will run between 90 and 100% constantly. Reloading the server will stabilize the CPU for a short period of time, however the CPU usage will always return to 90-100% utilization. Currently I have about 130 devices added to the system.
View 1 Replies View RelatedCisco WAN :: C4507R High CPU Utilization
Jun 12, 2013we have 2 Cisco C4507 Switches working As Core Layer, but the CPU Utilization is about 54% most of the time and sometimes it goes up to 70% or 80% also.
which services are causing this utilization. [code]
Cisco WAN :: 4510R+E High CPU Utilization
Dec 12, 2011we have cisco 4510+R switch with Cisco IOS-XE software & we are facing high cpu utilization on core 1 (95%) & on core 0 (15%) since last 2 hours.
I have taken logg file but did not understand how to analyzed it & where is problem. log file is attached.
Getting High Bandwidth Utilization
Sep 18, 2011I am working as net admin which is i need to monitoring and manage my workplace network( education center )I got a few question about network traffic flow. Here is the issued.I got high bandwidth utilization so high after office hours which is only on night. as we know, after office hours there is no person at the office but the traffic flow on bandwidth utilization is high.what are the possibilities of this issued?
View 1 Replies View RelatedCisco :: 7613 Having Frequent High CPU Utilization?
Apr 25, 2012I have Cisco 7613 on my edge(MPLS Backbone). CPU utilization is shooting to 100% at frequent intervals. When I tell vendors managing device they tell that it is happening due to one of my server(connected on Fast ethernet port of 100Mbps) generating heavy traffic. My questions are:
1. Can a router of 720Gbps capability be choked due to traffic generated by 100Mbps link?
2. Interrupt CPU process utilization is well below 10% at the said time. BGP router process consumes most of the CPU. Does this means that server in question is generating too many routing updates?
3. Is there any way that I can limit routing updates on a particular link?
4. how to check which link is causing more CPU utilization.
Cisco WAN :: High CPU Utilization On 7200-VXR With NPEG2
Nov 30, 2012My router is running with BGP (One eBGP and One IBGP session). I have filterdown the BGP roting table by using prefix-List and default route to upstream router.But still found the CPU process is high (80%/80% with 60MB traffic).
Sh Proc CPU
-------------------
CPU utilization for five seconds: 88%/88%; one minute: 87%; five minutes: 87%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
[Code].....
Cisco Firewall :: High CPU Utilization On ASA 5550?
Mar 10, 2013I have Active Standby ASA5550 setup with VPN premium license. A few days back we had a requirement of SSL VPN connection for and we got a temporary from Cisco for same, this license expired and the ASA reverted to it's original license. 3 4 days after this we saw a sudden increase in CPU utilization (upto 90% + -5%) on the ASA during production hours but were not able to figure out the reason, in order to restore the services we failovered the firewall to secondary and everything worked fine. We were suspecting one of the following but there were no logs for any of this
1. The ASA hardware was haivng problem
2. Some client was doing a DoS attack to bring down the ASA (no logs for this as well).
We took a downtime to look further by failovering the ASA back to primary and it worked fine without any issues ruling out the 1st option. We also came across a licesing doc [URL]
Downgrading any license (for example, going from 10 contexts to 2 contexts).
# Note If a temporary license expires, and the permanent license is a downgrade, then you do not need to immediately reload the security appliance; the next time you reload, the permanent license is restored.
As per this doc, sooner or later a restart was required on the ASA. We restarted secondary ASA and everthing was fine but when we restarted the primary ASA by swtiching over to secondary some of the server (not all) in the DMZ stopped working (even ICMP unreachable) and only came back to normal when the primary ASA was restored and working fine (with failover).
The reboot was done by shuting down the physical link between the Core switch and ASA inside individually.
I am not sure what could be the issue that the servers in the DMZ wen unreachable.
Cisco :: High CPU Utilization 7603 WS-SUP32
Dec 20, 2010Since a couple of months, I have some CPU problem.
There is no high process :
l#sh processes cpu | exclude 0.00CPU utilization for five seconds: 39%/30%; one minute: 32%; five minutes: 32% PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 130 52713208 240359987 219 0.95% 0.91% 1.00% 0 IP Input 202 1811824 1218190 1487 0.07% 0.06% 0.05% 0 HIDDEN VLAN Proc 338 20873364 219225 95214 7.11% 0.94% 0.71% 0 BGP Scanner
total amount of traffic on the router around 700Mb-1Gb out / 300Mb In
cisco CISCO7603 (R7000) processor (revision 1.1) with 458752K/65536K bytes of memory.Processor board ID FOX090308DTR7000 CPU at 300Mhz, Implementation 0x27, Rev 3.3, 256KB L2, 1024KB L3 CacheLast reset from power-on5 Virtual Ethernet interfaces9 Gigabit Ethernet interfaces1915K bytes of non-volatile configuration memory.
65536K bytes of Flash internal SIMM (Sector size 512K)
Cisco WAN :: High CPU Utilization In GGSN (7604 Ios 12.4)
Jul 26, 2011We have a CISCO 7604 Router (GGSN) in our customer site. Since two weeks are observing high CPU utilization (even touching 100 percent). We performed a SNMP configuration on this routers 2 weeks back as well. But SNMP process is not consuming much CPU resources. The following is the output of the "show proc cpu" and "show proc cpu history.
------------------ show process cpu ------------------
CPU utilization for five seconds: 50%/15%; one minute: 49%; five minutes: 51%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
[Code]......
Cisco Firewall :: High CPU Utilization On ASA 5540
May 11, 2008I have a remote site customer with a Cisco ASA 5540 running SSLVPN (Anyconnect)(8.03). It currently only serves about 450 SSLVPN clients. Since last friday, they've seen the CPU utilization go up to high 90% while only serving 400+ remote users. I saw some high cpu utilization bugs, but none looked to be relevant. How I can find the root cause of the CPU high utilization?
View 2 Replies View RelatedCisco WAN :: High CPU (99%) Utilization Of 4507 Switch
Dec 21, 2011I am facing lots of issue with cisco 4507 switch recently.. Every alternate day, its CPU is getting utilized by 99% and network stopped working..finally it has to be restared.
Below is the CPU utilization of the process:-
------------------ show process cpu ------------------
CPU utilization for five seconds: 99%/0%; one minute: 99%; five minutes: 99%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
[Code].....
Cisco Firewall :: High CPU Utilization - ASA 5520
Dec 22, 2012we have ASA 5520 with IOS 8.0 , when i am trying to add more static routes on the inside interface the CPU utilization is going up. one faced the same issue. I am configuring through the cisco ASDM 6.1(3)f.
View 1 Replies View RelatedCisco Firewall :: High Cpu Utilization On Pix 515E?
Aug 9, 2012I am facing high CPU util on my pix 515 E which is in failover mode.During peak hours the util is see rising to 60% where as in off peak hours it is normally12%.
During normal operation the average utilisation was observed to be 30% but suddenly from 2/3 days it is constantly 60% doule the value as earlier. Have gone through the logs and traffic but not able to tarce anything particular
below is the o/p of some command taken for analysis
IOS version 8.0(4)
sh cpu usage
CPU utilization for 5 seconds = 51%; 1 minute: 61%; 5 minutes: 58%
sh cpu usage
[Code]......
Cisco WAN :: High CPU Utilization On Router 2821 With 12.4 (24) T1
Jan 19, 2010I have a Router 2821 with c2800nm-advipservicesk9-mz.124-24.T1.bin and with a Cisco Integrated Service Engine(s) Cisco Unity Express 7.1.1 in slot 1 , this router shows a high cpu utilization.I think is a bug with the IOS , because there is no voicemail configured on the CUE, there is no traffic to the CUE , just traffic from:
- voice calls
- ospf
The ospf is not the cause of the high cpu , because the high cpu utilization appears before I put the ospf proccess on the router.
Cisco :: Sudden High CPU Utilization On AIR 1142?
Jun 24, 2012Five Cisco 1142 integrated in WDS infrastructure: 4 - AP, 1 - WDS with AP... At once on all access points loading of the processor increased to 100 %. And "show proc cpu" - in total in norm, log on all cisco identical below:
(Cisco IOS Software, C1140 Software (C1140-K9W7-M), Version 12.4(25d)JA1, RELEASE SOFTWARE (fc1))
Start problem...
Jun 25 16:11:58: %DOT11-6-ROAMED: Station f0cb.a123.d6f9 Roamed to 0c85.257f.05d0
Jun 25 16:11:58: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station f0cb.a123.d6f9 Reason: Sending station has left the BSS
Jun 25 16:23:36: %LEAPCL-3-TIMEOUT: AP Timed out authenticating to the WDS
Jun 25 16:23:42: %WLCCP_AP-6-INFRA: WLCCP Infrastructure Authenticated
Jun 25 16:23:44: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station a088.b405.7320
Jun 25 16:23:44: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 0021.5dbf.a3da
[code].....
The problem suddenly began, proceeded about an hour and also suddenly ended...
Cisco Switches :: High CPU Utilization On SGE-2000
Aug 17, 2012High CPU Utilization on Cisco SGE-2000
View 5 Replies View RelatedCisco WAN :: 7600 High CPU Utilization Due To Interrupt
Mar 3, 2013We have next router:
spb-bg3#sh inventory
NAME: "CISCO7604", DESCR: "Cisco Systems Cisco 7600 4-slot Chassis System"
PID: CISCO7604 , VID: V01, SN: FOX1523H7E8
[Code]....
Cisco WAN :: 3845 Processor High Utilization
Apr 22, 2011My client using 3845 as a core router . 200 number of branch are connected through 6 ISP.Some of days average process shows 90 % . Max time 50 %.In the morning when Branch location are off then time also high utilization.High utilization is not continue after intervals of time or periodic time its goes to high.
have any solution for that ?. before once 3845 is crash for that. another is ready for replacee.We test another device like core switches for observation CPU rate.
Cisco WAN :: High CPU Utilization On 7609-S Router?
Jan 20, 2011Have high cpu utilization on Cisco 7609 router. when i check output "Sh proc cpu sort".
View 2 Replies View RelatedCisco WAN :: 2811 Shows High CPU Utilization
Sep 24, 2012I have a router 2811 and shows high CPU utilization 90%, it is observed that this happens when the traffic increases, the router also has firewall enabled services, QoS, DHCP, ACLs, NAT. As my router could not determine what is appropriate for my use, and how it could choose a router that meets my needs.
View 6 Replies View RelatedCisco Firewall :: High Cpu Utilization On ASA 5520?
Sep 25, 2012I am seeing high cpu utilization on 5520.
fw# sh processes cpu-usage sorted non-zero
PC Thread 5Sec 1Min 5Min Process
0x081e1e11 0x6ddc1528 70.6% 66.5% 66.0% Dispatch Unit
0x08ed170c 0x6ddb9b48 1.6% 1.7% 1.8% Logger
0x08dd5f2c 0x6ddafee0 1.5% 1.5% 1.5% SNMP Notify Thread
0x08e8d045 0x6dd99348 0.1% 0.1% 0.1% ssh
Cisco WAN :: High CPU Utilization In 4506 Switch?
Sep 6, 2011I am getting High CPU utilization in one of my switch which has many layer 3 vlan interface and many other routing interface.In the o/p of show process cpu i get 64 % CPU utilization. The o/p is as below
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
30 37656252881151776906 3269 62.31% 63.95% 64.82% 0 Mgmt LoPri
And rest of the other process are very normal. Only cat4k Mgmt LoPri is consuming very high cpu utilization. I have checked all the interface input queue and all are very normal.
Cisco WAN :: High CPU Utilization Router 2801?
Apr 12, 2011I have problems with the Router 2801.When i give the command show processes cpu, the command show me that the router is working in 98%.
I have vlans like voice vlan and others, I have one 20 Mb Wan Link and I redirect all traffic from my lan to this link and when i browse in internet or i do downloads the router goes to 98%, when i don't make it the router processes goes down.
I thought be problem with hardware, but i exchange to another router and the same problem happened.Before this situation, I had one link with 12 Mb and nothing happened, when i exchange this to the 20 mb link the problems starting.
Cisco WAN :: High CPU Utilization On 3560 Switch
Oct 6, 2009We are facing a weird problem of high CPU utilization on 3560 switch. Even without connecting a single PC to switch, CPU utilization is showing 22 %. Any particular reason for this? Can configuration affect the CPU utilization even though there is no PC connected?
View 5 Replies View Related