Cisco WAN :: Maipu 800 / How To Connect 2 Sites With Different Subnets
May 27, 2013
I have problem of Site to Site connectivity I have 2 sites (Site 1' public ip. 115.119.120.X, local ips are 192.168.1.0, & Site 2' public ip 115.119.187.X, local ips are 192.168.2.0)Both sires are having different locations & using routers are Maipu 800.At present both sites are running with internet (each router are configured for DHCP, NATING & DNS for intenet)guide my with complete config, both local systems has to communicate...My preperance is existing routers & If it is nessary to change the routers, what will be the config.
I have 2 DSL Lines going into a load balancing router. The load balancer is set up to distribute the traffic equally on the two lines, hence doubling the bandwidth. Though great at load balancing, it cannot handle DHCP for the 50+ users on our network, and therefore we are using another router for DHCP, which is running DD-WRT firmware.DSL 1 - 10.1.0.1DSL 2 - 10.2.0.1Load Balancer - external 10.1.0.2, 10.2.0.2 internal 192.168.10.1. DHCP Router - external 192.168.10.2, internal 192.168.1.1All other devices - 192.168.1.xThe load balancer has many options to direct traffic to one WAN port or the other based on IP address, which we would like to implement. But right now, since all my devices are on the 192.168.1.x subnet, it can't see anything but the DHCP router. So essentially it thinks it has only one client.
I need to NAT some subnets to one IP and other subnets to another IP. The range command want work because some of the subnets are out of order.For example subnets 192.168.1.0 - 192.168.7.0 and 192.168.25.0, 192.168.28.0 nat'd to 1.1.1.1. subnet 192.168.26.0-192.168.27.0 nat'd to 1.1.1.2
How is it possible to connect a host to a switch when they're in different subnets? I'm new to Networking and was thinking it may be achievable through VLAN configuration?
my local site has Cisco 2811 router connecting locally to ASA 5520. Remote site A has Draytek Vigor2950. I have working vpn between local subnet 10.0.0.0/24 and remote site A 10.100.6.0/24. I have remote sites B (10.100.7.0/24) and C (10.100.8.0/24). I would like to route traffic from local site to remote sites B and C via the local-to-remote A vpn. On Draytek routers B and C, I have added to subnet 10.0.0.0/24 to the remote network profile list. On local router, I route traffic for subnets 10.100.7.x and 10.100.8.x to the ASA. On ASA I have added these subnets to the profile for local-to-remoteA vpn.But the vpn will not establish when I attempt to ping from local to remote B or C.
MY ISP installed one router in my lab.for internet connectivity they mail me steps :connect your Laptop directly to gi0/3 port to check internet connectivity with public ip 1.1.1.x and Gateway 1.1.1.1 with subnet mask 255.255.255.240 after connection I surprised because I am able to access only google sites like gmail,google search etc. but I am able to ping/traceroute all sites.from browser I am able to access only google sites only.In Router no firewall no such access list.
my situation is that i have to connect 2 site which are 1km apart our data speed requirement is not so high 64kbps is enough so i heard this kind of setup is it best
I've been having problems for the past couple of weeks trying to connect to some websites. It is only SOME, not all websites. It will either say that it is taking too long to connect or that the website is experiencing problems.
Can't connect to sites such as this GamersFirst Forums -> International APB Reloaded Forums, unless I use a proxy site.Nor does connecting to the game works, either. But it works for my friends, apparently.I checked the router settings, no go. Turn the firewall and Norton on and off, and still the same. I even tried accessing on my sister's computer which is also connected to the same router, and it connects. Only my computer doesn't connect to some certain sites.
I have a laptop that works perfectly fine when plugged into a network cable, but the wifi refuses to work. It pulls an ip, and everything looks good when I run ipconfig/all, but it can't even ping the router. All other computers on the network are working fine. I've flushed dns, set static IP and DNS, uninstalled/reinstall device, updated drivers, bios, and firmware, and even created a backup image of the computer and reloaded the os using the recovery partition. The event log doesn't tell me anything, and there are no flags in the device manager. I'm at a complete and total loss. I cannot figure this one out.The laptop is a Compaq Presario CQ50-142US. Vista 32bit OS. Everything was working perfectly fine before it got a virus. I ran through the standard procedures of AVG, Malwarebytes, TDSSKiller, and even resorted to Combofix, but somewhere along the line the wifi dropped off and will not come back.I even double checked the HOSTS file and IE proxy settings to ensure I wasn't crazy; although I know those should've affected the wired connect too.My last step is to either replace the wifi chip (which I don't think is the problem), or wipe it and load the os from scratch, but I don't have an oem disc since it has the recovery partition.
I can't access some sites, loading times are endless and they look totally strange when I can access them (No images and so on). Sites are completely random, some examples are GamersLegacy.it - Starcraft 2, Diablo 3, Dota2, World of Warcraft, League of Legends, Inferno eSports - Homepage (videogames forum)FINECO: Conto, Investimenti, Trading, Prestiti e Mutui - Banca diretta, online o con promotore (bank) Sigma Draconis
1) Cleaned laptop with Ad-aware and Malwarebytes, found 2 issues but didn't fix the problem.
2) Closed firewall, nothing either.
3) Canghed/flushed DNS, tried both openDNS and GoogleDNS, nothing.
4) She CAN access those sites, she has same connection to the router (via wireless) and she has same OS (Windows Seven). I think that means it's my problem, not a router one.
5) Tried to lower MTU settings in my wireless connection as I read that could be the problem, nothing new here.
6) Here comes the tricky part. I tried to access those sites via proxy (Ninja Cloak | Fast, free, anonymous web browsing with NinjaCloak.com) and they actually work!
I have dir655 Hardware Ver B1 Firmware Version: 2.10NA.Comcast Motorola cable modem surfboard SB5101. The problem started happening a couple of days ago. When my computer is hooked up to the cable model directly, i am able to connect to outlook.com just fine but when i go through my router, it can't connect to the site. I played with MTU (lower it by 10) all the way to 1300 but it didn't work.The problem started happening all the sudden without any changes in the cable modem, router or my computer.
I also tried cloning MAC address from my pc but didn't work.I also tried turn off both modem and router, wait 2 minutes, start modem, wait for all lights to come up and start the router.Sites i can't connect are: outlook.com, starcraft2, Comcast, eBay, Facebook.One thing that i noticed weird is that i am able to connect to cnn.com using IE9 just fine but ping shows: [code]
I'm having problems connecting to certain sites on the internet through one computer. I can connect ok on other computers going through the same home network. On the one computer that is having problems I can connect to the site but then when I click on a link I get unable to connect then I can reload the page and some times it connects to the page. So as I am browsing through the site almost every time I click on a link I get unable to connect and have to keep reloading the page.
WIth Chrome it does work although a bit slow. With IE as-well.Had the problem with FB as-well allthough that i could cancel with allowing it to connect.Gmail doesnt.Production Security Services and the certificates seem to cause problems.Searched the internet; tried a scan, checked the date, activataed the SSL and TLS in the browsercertificates, the server and organisations names.
We can't find the Linksys router's manual and have no clue what is causing our WiFi not to let us access certain websites. For example, we are unable to access the Microsoft, Target, our local Library, YouTube and some other ones that we find out about once it doesn't let us get on them. We thought it was an issue with Microsoft Security Essentials because we hadn't updated it correctly, but that was not it. The reason we know it is OUR WiFi because we can access the sites I mentioned above whenever we use our apt complex WiFi, so it is not our laptop. We have the same problem with this when using our wifi on our iTouch. I hope that all made sense (had to access this site with my phone.)
I'm trying to solve up a really nasty problem I have at home and I've come here hoping to find some answers. Since last Saturday, I am unable to access certain internet sites when at home. Strangely enough everything was fine before that. Went to bed around midnight local time and when I went to check those sites after work at around 3:30 pm local time I could not get on those sites. For some reason the pages just keep on endlessly loading, giving me only a blank page. What is also strange is that no computer in my house can access those sites. So it's not limited to one computer.
I have inherited a sbs 2008 network where they have a SBS2008 server and Server2008 running as a terminal sever at the main office and they have 2 satellite offices. These offices all connect through router to router vpn tunnels. The main site is on 10.0.0 and dhcp is done by the sbs. Satellite site a is on 10.0.10 and dhcp is done by the vpn router and Satellite site b is on 10.0.5 and dhcp is also done by the vpn router. All client computers can run rdp to access shares / programs etc on the two servers but when trying to push out group policy, antivirus updates or even using remote control through the SBS2008 server it is hit or miss. DHCP records on the SBS server do not seem to update correctly, manually changing the ip address in DNS records results in warnings that the PTR record cannot be created.
So I am wondering if the configuration they currently have setup is correct. What might be stopping some but not all computers from updating, why I can connect to some but not all computers at site "a" but I am not able to remotely connect to any computers at site "b".Why I can do remote installs of Eset Endpoint Security on roughly 10% of the clients but the other 90% fail.
My only options for internet have been 56k or wireless USB modems. That is, until recently. We switched from the wireless USB modems to a wireless hotspot from US Cellular (Samsung SCH-LC11). However, ever since making the switch I've had problems accessing certain websites both on our PC and on my Macbook Pro. I can't connect to Invision Free (or any of its user-created forums) or [URL]. It happens with other, random sites as well. I tried manually changing DNS settings to Google's and another one (don't recall which) and it did allow me to access the site. However, once there, every other site started moving slowly and eventually the ones in question timed out as well.
I built a computer down at school in Utah, semester's over so I went back to Idaho for the summer. When I got here I seemed to stop being able to connect and load content from random sites. It gets a ping time out every time on the same random websites.
Some of the sites:
[URL]
I can access these sites in Utah, so I called my ISP (frontier communications, previously verizon.) They flushed the DNS and checked that the modem wasn't to blame. I checked my host files and they're unaltered. After two hours on the phone they were stumped and hung up. [URL] loads fine, but it won't load the pictures which is odd.I'm not sure if it matters but I do have a 6 year old modem (westell 327w) that I think uses LAN g whereas my mobo (asrock extreme3 gen3) uses Realtek 8111E if i'm looking at the correct specs.one last thing to add would be that I am not able to access [URL], but I am able to access [URL]. Is there something all these websites have in common that cause them not to load?
For some reason there are some sites that I cannot access websites from inside interface.One such example is lxer.com where I am receiving this message in the browser:The connection has timed out The server at www.lxer.com is taking too long to respond.This has "suddenly" happened, and so I am wondering what others have done when such things has happened. My outside has a dhcp-IP, and I have noticed that this address had changed, so I corrected this in my router settings.ASA version is 5505
I am using a USB Modem from HUAWEI Technologies to use internet when im not on a wifi zone.. The Internet Speed is kinda slow (512 kbps), so I configured my browser to go through a proxy to make it a lil bit faster (2mbps now)..Everything works fine except that I couldn't connect to https sites (gmail, facebook, eBay, etc)
My Toshiba will not connect. I keep getting cannot connect to server messages. Also get the error 623 message. Im not sure what to do. I use Windows xp on it. Bought it in 2006. I had thought about reseting it to factory settings but I never made restore disks and cannot find the toshiba reset stuff.
I am using a USB modem to go online when i'm not in a wifi zone.. The internet speed is very slow (512 kbps) so I configured my browsers to connect via proxy to boost the speed which is now (2 Mbps)..Everythings working fine except that I cannot connect to SSL sites, e.g Gmail, Facebook, Ebay.
I am trying to connect two overlaping IP address sites ( see attached diagram). Site A LAN address will dynamic NAT to 10.1.1.0/24 at ASA5520.All the users from site A need to get services from site B ( DHCP, DNS, Mailbox,Print Servers, AD loggin etc). All the connections will be initiating from site A to B.
1-will all these services will run over NATed address.( dynamic) or I have to change to static NAT?
2- Any sample config for ASA 5520 for this type of network?
I have got two 878 integrated services routers and I need to configure them as transparent bridges in order to connect 2 remote sites over ATM.
As I'm testing the topology, I configured two switches (representing the sites) at each end with a VTP domain. VTP works while the switches are connected directly with eachother, but it won't work with the bridges in the middle. [code]
Unable to connect to unsecured wireless sites using a USB Realtec high gain antenna on a Toshiba laptop running Win7 Pro, 64 bit. Network troubleshooter resets adapter but states it cannot correct the problem. Wireless adapter settings set to High Performance. Latest Realtec drivers have been downloaded and installed. Light on front of the laptop shows that the wireless function is running. Turned the function off, rebooted and then turned it back on. Same result when Toshiba is operating off 110v so power shouldn't be the problem.
I could not log into any of the 4 FTP sites that I normally update without immediately getting disconnected. The message I am getting from the servers is "Port command failed, error loading directory - disconnected". To save some time and posts, here are the facts....1.) It is definately not my DSL modem. When I connect directly with the modem, without a router, I can connect to FTP fine2.) I have already done a /flushdns in IPconfig.3.) I have already done the typical power off/power on/reboot procedure numerous times.4.) I have already tried PASV mode, and tried turning PASV mode off as well.5.) My login information is correct, and I have problems on multiple sites.6.) This problem has been reported before by other users of WRT54G, but the other forums I see have no solution to the problem.7.) I have already tried using other PC's and different FTP clients on my home network. No matter which PC or laptop I use behind the router firewall, I can't maintain FTP connection. 8.) I have never had to open ports to be able to connect to FTP, since I am the one doing the request. I did also try opening ports 20 and 21. 9.) XP firewall is disabled. 10.) I have tried both ethernet ports on my PC. But then again, that is irrelevant because none of my other PC's which connect wirelessly, can connect either.
Not too much networking savvy - but here goes. Want to use router as local lan - no wireless. When router is connected to laptop via RJ45 I loose my ability to connect to sites via browser. IPconfig shows wireless adapter at 192.168.1.3. When router is attached it's ip is 192.168.1.1. Disabled the wireless in the settings but no dice. When the router was used with DSL it was set at PPPoE but now that I'm just using it locally not sure whether it should be DHCP or Static or other.
I have a home network. There are a total of 3 PCs. Each runs Server 2008 32 bit. One PC - Lets say Server A has 2 NICs with Ip addresses, 10.0.0.10/30, 10.0.0.2/30. Other two computers Server B and Server C have single NIC with addresses 10.0.0.1/30 and 10.0.0.9/30 resp. So as you can see that there are two subnets 10.0.0.2 - 1 and 10.0.0.9 - 10. I can ping B and C from A. I want that B and C can also ping each other and if I run tracert on B or C, it should give me the route to the destination via A. All this without any other hardware. Like using route add... etc eg. if I write tracert 10.0.0.9 on B, it should return a route like 10.0.0.1-----10.0.0.10------10.0.0.9.
I have two subnets, that need to share a common link, and each with its gateway at the opposite end. What kind of switch do I need for the two red boxes?
I have an exercise with picture you find below. The question is: Will the network shown in the diagram work correctly when you consider that the MAC-addresses PC0 and PC8 are the same, and why?
I recently added a post lately referring to drawing a topology of a large network with a high number of hosts. Now with project itself, I'm designing a network for a large organisation with a different number of hosts at each location.These are, 500,18,52,236 and 12. The location with 500 hosts is the head office, to which every other branch has a wide area network connection through a serial link.How many subnets would I require? I wrote down subnet details, but only for 5 subnets, a subnet for each location. Is that all I need? Or do the WAN connections count as subnets
