I have 1941, 2901 ISR routers. I will use 3G backup when primary link (metro ethernet / G.SHDSL) goes down. Do I have to use Data License (SL-19-DATA-K9 / SL-29-DATA-K9) in order to switch back to 3G when primary link is not reachable) ?
View 7 RepliesI am setting up my lab using two 2901 routers which is running on 15.2 IOS.I am trying to simulate a back to back BRI.BRI Module: WIC-1B-S/T-V3 (x2) one of each router.
I followed this amazing document to understand the concept of BRI and configuration. url..but it never says if i can use the module that i have mentioned.
Q1. What cabling i need to use to setup back to back BRI using 2x 2901 routers with these modules?
Q2. What cabling do i need to use.
Q3. Is it actually possible to use these 2 modules alone to simulate a back to back BRI..?
I am having this issue with only one rack in the lab. The three routers (2911 , 1941, 2901) connect together through Smart Serial cables going to WIC-2T cards. In the configuration both serial connections going to the 1941 have the DCE.
When going to configure serial 0/0/1 I am allowed to apply a clockrate to it, however, I am kicked back an error saying that a clock rate can only be configured on DCE interface. They are both without a doubt the DCE end connecting to the WIC-2T interfaces. What could possibly cause this problem. Would SCTE or something with the auto clock-rates on the router create this problem.
The license has been installed onto the router. Here is the relevant out from the show license all:
License Store: Primary License StorageStoreIndex: 0 Feature: ipbasek9 Version: 1.0 License Type: Permanent License State: Active, In Use License Count: Non-Counted License Priority: MediumStoreIndex: 1 Feature: WAAS_Express Version: 1.0 License Type: Permanent License State: Active, Not in Use License Count: Non-Counted License Priority: Medium
WAAS license as it says that this is not in use, WAAS under the interface is not possible.
Need to know if I have 2 type of license on my 2901 router: ipbase and uc, will the 2 type of fuctions of this license work at the same time. Another words will i have route and nat functions work with voip having to type of license on my 2901?
View 3 Replies View RelatedI turned a Belkin Surf N300 into an access point using the settings page via IP address, now I can't seem to find that page again so I can switch it back. The model number is F7D6301 v1.
View 7 Replies View RelatedIs it possible to get a PAK back from a license? For example, if the PAK is joined with the wrong serial number is there a way to revert the binding of the PAK and serial to get just the PAK again?
View 5 Replies View RelatedI currently purchased, Cisco 1941/K9 with 2 onboard GE, 2 EHWIC slots, 1 ISM slot, 256MB CF default, 512MB DRAM default, IP Base.
Questions
1. With IP Base License, will I be able to run Frame Relay? I really need reference on what works and what doesn't between these different technology package licenses ? Actually frame relay is running on it right now, hope it doesn't suddenly stop after 60 days...
2. As I understand in order to run MPLS, I will need to upgrade to Data License "SL-19-DATA-K9". Since, I already have a Cisco 1941 to upgrade it, I need to order a spare license / paper PAK?
3. Does the IP Base License support site to site IPSEC VPN or do I need to purchase a security license "SL-19-SEC-K9"
4. Can I have both security and data license activated on the same device ?
5. If I do activate security or data license will I be able to use the IP Base features at the same time?
6. If I purchase a new Cisco 1941 with Data or Security License do I need to purchase the IP Base License then upgrade the license?
7. Is the 1941 suited for voice application routing ?
I am setting up a network that will use the 1941 router with a cellular card (HWIC) to connect to the Internet for communication with remote stations in the field. The 1941 has a static IP address (166.142.xxx.yyy) on the Internet provided by the ISP (Verizon). The 1941 is connected via ethernet to the ASA5510. The end goal is to have the field cell routers (Digi Transport WR-44-R, also static IP) connect to the ASA5510 via VPN tunnels for communication back to the servers behind the firewall. I'm not sure exactly how to configure the 1941 so that the remote router can connect to the ASA using the public IP of the 1941 router. I have the 1941 working stand alone and can connect to the Internet and pass traffic, but I tried a static NAT to translate the public IP to the private IP of the ASA and cannot pass traffic. below is part of the 1941 configuration: [code]
Do I need to use VLAN bridging to accomplish the task or am I missing something with the NAT?
I have recently purchased 2 x 1941 routers with 2 L-SL-19-SEC-K9= and 2 L-FL-SSLVPN10-K9= licenses. I've installed the licenses through Cisco Configuration Pro ver 2.5 and installation did not generate any errors. After saving config and reloading the device, on the License dashboard, the deploy status for the SSL VPN is "Not deployed" and I have no way of deploying it. The state also says "Active, Not in use". I have tried reinstalling the license via command line but get error "license duplicate - already installed" suggesting the installation was OK. The sec license deployed without any issues. Is there any way to manually deploy this SSL_VPN license?
View 4 Replies View RelatedJust to get this clear as having issues with a E1 link with CRC's at one.Router A,Network-Clock-Participate WIC 1,Should router B have clock participate for WIC 1? We currently have controllers set as UNFRAMED but guess we can set to NO-CRC4 both ends and telco will pass this.
View 1 Replies View RelatedI'm looking for instructions on how to setup and connect two RV082 routers together with a crossover cable between their WAN ports. This is to connect two separate LANS together via an ethernet connection. For staging we are setting everything up with a crossover cable in our shop. Ultimately the crossover cable will be replaced by a microwave link between the two LANS several miles apart. There will be no internet connection.
View 7 Replies View RelatedI searched a lot but couldnt find a clear document about connecting 2 G.SHDSL routers back to back.First of all I am not sure which type of cable (RJ11) is used for connecting two 878 routers. Does it have to be cross or straight cable.
Which RJ11 pairs will be connected each other [code]
According the configuration samples One router must be CPE and the other must be CO for simulating DSLAM.
I would like to Upgrade license Cisco 1941-K9 from ipbase to security
View 5 Replies View RelatedI have a cisco router 1941 and i have uploaded before evaluation license , now i have already bought cisco security license .I have already installed on cisco router , but the problem the router is still using the evaluation license not the new license .
RSP#sh flash:
-#- --length-- -----date/time------ path
1 55088360 Oct 10 2012 06:04:10 +00:00 c1900-universalk9-mz.SPA.151-4.M4.bin
2 2903 Feb 4 2013 12:23:32 +00:00 cpconfig-19xx.cfg
[Code].....
I'm having some trouble getting two Cisco 888's to work correctly back to back.. The two routers will ultimately be used in conjunction with a BT EPS8 circuit which is effectively four wires short distance between customer sites. We have configured lots of these using the older Cisco 878's.
Anyway, as i've been struggling to get line sync on site I've gone back to basics and connected the two 888's back to back. However, I've found that no matter what I do I can only get the routers to sync at 384kbps!? And that's with a one meter RJ11-RJ11 cable.. Very strange. When we've used the 878's we get much more bandwidth. I have tried statically assigning the line rate at both ends but it still only works at 384kbps.
I have a sending application that it is establishing a TCPIP socket connection to a vlient that has a receiving application on another server (completely separate networks) The receiving end has a Cisco Router 1605R and has allowed my connection using this firewall rule
access-list 101 permit tcp host xx.xxx.xx.xx any eq 5600 log
(where the x are actually numbers corresponding to the senders IP address)
I can establish an outbound connection to the receiver and the connection shows up on the machine. After the connection is established I can send data and it is received by the receiving application (I observed this using a socket test application, data actually gets through the firewall) However I need to send an acknowledgment back on the same session to the sender. This cannot be transmitted and shortly after I try sending the connection is closed with error 10060.
The 1941 router has USB ports, Will it support a USB celluar data card?
View 5 Replies View RelatedI have a Cisco 1941 router... ipbasek9. I want to use this at home for my primar LAN->WAN interface. So i need the Security license enabled.I have enabled the Security temp/eval license but can not find a way to manage it.I have tried downloading the Cisco Configuation Assitant, but this errors with "Unsupported Device type"
License output and config outbout below (no WAN interface on 10.0.x is just internal testing WAN IP. This device is not yet directly connected to the internet.
cisco1941#show lic
Index 1 Feature: ipbasek9
Period left: Life time
License Type: Permanent
License State: Active, In Use
License Count: Non-Counted
[code]....
i installed Data license(Evalutation) initally it took the license after reload, when i enter sh lic command the out put shows that Data license is installed and valid for...
But when i run sh ver command it only shws ipbase license and not the data license
is it possible to assign a loopback address to a typical switch port on a 2950 switch? I want to be able to have some devices connected to a switch to test access lists and VLANs.
View 3 Replies View RelatedI have Cisco Catalyst 2901 switch with Sup engine which have CatOS installed. I want to know that can I install Cisco IOS in this switch.
View 1 Replies View RelatedI am having a bit of trouble with the following scenario; I have two 2901 ISRs and a 2924XL setup in the following fashion.
2924XL--->P2P-Fiber--->2901ISR--->P2P-Fiber--->2901ISR
I need to be able to reach the LAN 192.168.1.0 from 192.168.3.0 for TS but cannot get this to work. I can ping from within the switch all around and i can ping from within the woodlawn router all around but cannot ping host to host.
I have some confusion about some hardware components. I watched the video datasheet of cisco routers and switches. In cisco 2901 and 2911 models of routers there is service module . What is meant by service module. what does it do ? If we buy a new 6500 switch, what are the components we get bydefault. Is there any special configuraton to be done for 6500 . like Sup engine config etc. What is the difference between ASIC and Sup engine ? In which slots, we need to insert Supervisor Engine ? does it vary with the model . (6503, 6505, 6509, 6513 etc).
View 6 Replies View RelatedI have to install and configure two 2901 routers at different location with high availability. These 2 routers would be connected through WAN, now I would like to configure high availability bwtween two routers.
I have attached a small diagram of the placement of 2 routers.
how do I configure high availability between these 2 links or routers.
Does the 2901 have etherchannel capabilities? If so, how to configure it? I mean, I can type "show etherchannel 1" in it, so I would assume if I can show it, I better be able to configure it, right?What about the 2911?
View 1 Replies View RelatedI have some specific traffic that I am attempting to pull off of VLAN 310 at the router, apply a route-map that sends this specific traffic back down to the switch on VLAN 55 (and the private address) and once it hits the switch apply a route-map on that VLAN 55 interface directing the same traffic over to the 72.x.x.9 address which goes through a FAP box back up to the router on another interface.
I have attached the config information, I know this isnt the best practice way to do this however right now this is how I have to do this.When runing a trace from the net traffic stops at .2 and when running a trace from my test /30 it stops at .2 as well. I am not sure what to do at this point
[code]...
I have a Cisco 1941 K9 Router. I want to add POE functionaltiy to it. Specifically I want a 4 port EHWIC POE switch to power a couple of AP's.
This is what I understand I need; Upgrade/replace the internal power supply with PWR-1941-POE power supply, This is supplied with a fan replacement also (not yet purchased).buy 1 x EHWIC-4ESG (4 port switch)buy 1 x ILPM-4 (inline daughter card / power supply board) I think the real question here is the 4 port switch... there are two types available one is EHWIC-4ESG=the other is EHWIC-4ESG-P=
Is there any difference between these two switch modules? or are they the same and the more expensive "P" version is simply supplied with the ILPM-4 daughter card for POE?
I have recieved via courier today 1 x EHWIC-4ESG, and found a ILPM-4 on ebay for a good price. WIll this provide POE through the switch EHWIC-4ESG?
I have a cisco 1941 router. Stock standard vanilla hardware, no extras. Standard universal image. Data and Security not enabled.I would like to add a 4 gigabit port POE switch (EHWIC) module to the router..The 4 port POE switch module will be used to power and connect 2 x Areonet AP's for my home. I'm replacing a Apple Airport Extreeme and Express setup. I'll possibly later use the two remaining POE ports for security cameras.My question is, what extra hardware and or IOS version do I need for the POE swtich module to function on the 1941? [URL] I think this is the model I want EHWIC-4ESG-P #4 port 10/100/1000 Enhanced High-Speed WAN Interface Gigabit Ethernet switch with Power over Ethernet?
View 1 Replies View RelatedMy questions is can a 4 port PoE switch module (EHWIC-4ESG-P) and a 8 port switch module (EHWIC-D-8ESG) be used at the same time in a Cisco 1941 router?
View 1 Replies View RelatedI signed up for Linksys Cloud access.. now going to my browser 'the old way' is disabled.. is there any way to switch back to accessing my EA 4500 using the old way by putting in 192.168.1.1 into the browser?
View 2 Replies View RelatedI have installed a new 2901 router with the IOS version 15 code (c2900-universalk9-mz.SPA.152-3.T.bin). I have a template config that I have created for my remote VPN routers that I have been using on 2811 routers with version 12.4 (c2800nm-advipservicesk9-mz.124-24.T1.bin).I do have the securityk9 active on the 2901 software
Technology Package License Information for Module:'c2900'
-----------------------------------------------------------------
Technology Technology-package Technology-package
Current Type Next reboot
------------------------------------------------------------------
ipbase ipbasek9 Permanent ipbasek9
security securityk9 Permanent securityk9
uc None None None
data None None None
Issue is when I do a "show crypto session" the GRE tunnels session status read down on the 2901 router but on the 2811 session reads up-active. Everything is working and I am routing over the GRE Tunnels.
[Code] ......
I have a 1941 that I am going to deploy with a HWIC-D-9ESW switch module (I only need 3 switch ports but need the PoE). I am going to hang a 1262 autonomous AP off one of the ports but I need to configure MAC address port-security so that only that AP can pass traffic. I know the switch modules are 'almost' exactly like a switch for commands but I can't seem to enable or configure any port-security settings. Is port-security no available on the switch modules?
View 3 Replies View Related