Cisco WAN :: Retaining System Logging Message History After Rebooting 3845
Oct 12, 2011
For some reason I am unable to retain the system message logging and config archive references after a reboot of the router. I need to be able track config changes and retain the ability for the customer to recover the original config should they destroy the config through any misguided fiddling on their part. There is no remote management and these router need to be recoverable. I know this used to configured by default on earlier routers as I've checked on teh ones we have, but checking through the configuration has not worked and i have everything configured the same but system messages are still lost on reboot. Im using Cisco 3845 running IPbase 12.4(3) and the config i have is shown below.
Logging buffered 4096 debugging
no logging console
!
!
Archive
Log config
Logging enable
Logging size 100
Notify syslog
Hidekeys
Path flash:archive-config
!
Logging history size 200
Logging facility local6
View 2 Replies
ADVERTISEMENT
May 2, 2011
I have 3845 Router which is continuously rebooting; console output is attached.
View 8 Replies
View Related
Jun 12, 2012
I might have to reboot my operating system, I have a Cisco wireless router, so I have to reset it, and set it up again after i reboot my operating system?
View 8 Replies
View Related
Feb 26, 2013
I recently formatted the flash drive of an 1800 router and replaced it with an updated image. However, the new features within the new image aren't reflected in the router. I believe that this is because a reboot would be required for the updates in the new image to be reflected in the router i.e. the image needs to be added to the system. How to get the image to the system without a reboot and if by doing so I would get all the new features from the image.For example, the show version below shows the old image in the system as [code]
View 2 Replies
View Related
Nov 12, 2011
I received a syslog message on my cisco 3845 router, what is that message mean. 11 13:36:06.265 UTC: ASSERTION FAILED: file "../les/if_ng_dslsar_tx.c", line 385
View 2 Replies
View Related
Sep 21, 2012
logging buffered 4096 warnings The above causes router to log all the events with severity level 4 or below in buffer.What about logging console warnings command?will the above command cause router to send log messages with severity level 4( warnings severity level) to console only or will the router send all the log messages with severity level 4 or below to console ?
View 3 Replies
View Related
Nov 11, 2012
Unable to see the logging message on the user context on ACE,but able to view the logging on the Admin Context.
Admin# sh logging
Message logging: none
Buffered logging: enabled (level - debugging) maximum size 1048576
Buffer info: current size - 1048576 global pool - 1048576 used pool - 1048576
min - 0 max - 1048576
cur ptr = 916918 wrapped - yes
[code]....
View 4 Replies
View Related
Sep 13, 2012
I have a cisco 3845 running 12.4(15)T10.
I can send a POD and disconnect my session. But when I try to send a COA, I always get back the same error. Here is the debug log:
*Sep 14 17:25:16.017: COA: 172.16.XX.XX request queued
*Sep 14 17:25:16.017: ++++++ CoA Attribute List ++++++
*Sep 14 17:25:16.017: 66F2DBEC 0 00000009 string-session-id(337) 8 0000007F
*Sep 14 17:25:16.017: 670B3394 0 00000009 sub-qos-policy-out(346) 11 POLICE-TEST
[code]....
View 10 Replies
View Related
Jan 26, 2012
I have an 3845 router:Cisco IOS Software, 3800 Software (C3845-ADVIPSERVICESK9-M), Version 12.4(11)XJ4, RELEASE SOFTWARE (fc2)After an unexpected reboot it says: System returned to ROM by bus error at PC 0x6323F398, address 0xB0D0B39 at 12:35:09 GMT Fri Jan 27 2012..To troubleshoot this error I need to find out what kind of processor this router has. It doesnt fall in either of the categories descibed in url...
View 4 Replies
View Related
Aug 2, 2011
I'd like to know if it's possible to change the system message for each ephone independently with CME ?I mean, changing an ephone's system message without changing others' ones.
View 3 Replies
View Related
Apr 29, 2013
I'm using "WS-C4948(12.2(54)SG)+PWR-C49-300AC/2". The following message are logged in the system log, but it was to check the status with the show command and status LED, but there was no abnormality. I thought the power supply has failed, but I seem different.
040861: Apr 27 07:00:50: %C4K_IOSMODPORTMAN-4-POWERSUPPLYBAD: Power supply 1 has failed or been turned off
040862: Apr 27 07:00:50: %C4K_IOSMODPORTMAN-4-POWERSUPPLYFANBAD: Fan of power supply 1 has failed
I checked.>> #show environment alarm no alarm
#show environment status power supply
Power Fan Inline
Supply Model No Type Status Sensor Status
------ ---------------- --------- ----------- ------- -------
PS1 PWR-C49-300AC AC 300W good good n.a.
PS2 PWR-C49-300AC AC 300W good good n.a.
All Status LEDs are green.
View 5 Replies
View Related
Jan 8, 2013
Just upgraded our WCS server to the 7.x code over the weekend. Turned up the first 3500 series AP's today. The AP's have been up for about an hour. I am seeing the Air Quality graphs on WCS. On the Worst 802.11a/n and 802.11b/g/n Interferers windows, I am see a WCS System Error Page message but only in those windows. I have gone over the documentation and dont see that I need to enable anything else on WCS.
View 5 Replies
View Related
Aug 15, 2011
I am getting a message "system standby.."Print Spooler"is preventing the machine from entering standby... try stopping the service?
View 2 Replies
View Related
Jun 7, 2012
I have a router Cisco 2800, but always is in Rommon, the message show is:
device does not contain a valid file system
dir: cannot open device "bootflash:"
rommon 8 > dir usbflash0:
Checksum failed on c1840-usbfslib-m
Expected checksum: 91d6, calculated checksum: 4527
open: file "c1840-usbfslib-m" not found
open(): Open Error = -1
loadprog: error - on file open
cannot load the monitor library "bootflash:%c1840-usbfslib-m"
from device: usbflash0dir: cannot open device "usbflash0:"
View 5 Replies
View Related
Oct 17, 2011
i have acer travelmate2350. i want to use internet in my laptop by wireless but i am getting a message "no supported wireless adapters available in the system" on the icon of wireless (red cross is also showing).
View 1 Replies
View Related
Feb 7, 2013
I have Dell Inspiron 15 3520 laptop bought in December 2012 with Windows 8 Pro. It was working fine until two days ago. I am unable to obtain DHCP lease either through wireless or wired network. After troubleshooting, I found DHCP service is not running and try to restart but of no avail.I ran sfc /scannow and the results are OK.
View 2 Replies
View Related
Aug 27, 2012
I have some 1142-lap that i have to deploy in my office.
I have successfully deployed 5 out of 8 LAPs . Actually the LAPs was not discovering the controller automatically.
So i had to configure the Controller ip adress through the console in tha AP using the CAPWAP command. Then the AP promptly associates with the controller. Later on i configure the AP name - Primary , Secondary , Tertiary Controllers and everything else and saved it on the controller. This worked out well for the 5 LAPs that i had.
But started facing a peculiar problem with the rest three
As soon as i disconnect the AP from my desk and have it mounted on the celing , to my surprise if find that the LAP doesnt retain its configuration and also doesnt associate with the Controller.
Cant imagine what could be the issue.
I have been told that one CANT wite/save any configuration manually on tha LAP using the console, except by associating it with the controller. Is it a fault with the AP ( as the other APs are working absolutely fine)
View 9 Replies
View Related
Nov 16, 2011
I'm encountering what I think is an issue on logging system on FW ASA 5520 - Asa Version 8.4(2), ASDM version 6.4(5). When I disabled the logging inside a rule from ASDM, or from console with the "log disable" option inside ACL, If I check in ASDM logging real time window I continue to see all the entry related to disabled rules. This is a correct behaviour about ASA logging ? How I can "hide" the entry related to disabled rules (this is what I need for troubleshooting purposes) ?
View 1 Replies
View Related
Jun 28, 2011
I have 350 WAP (1142n) running of two WLC 5508 (IOS version 7). WLCs are not located on the same subnets/locations and are not configured as mobility groups. The vlan ids on both wlcs are not identical.
[Code].....
View 6 Replies
View Related
Feb 24, 2012
Comcast service went down in our neighborhood and when it came back up my internet was down and all five LED lights on my Linksys router are solid green. Tech support tells me that I have to reset the unit to get it to function again.It's been a very long time since I set up the home network and while I'm pretty sure I can make my way through setting up from scratch (I'm assuming resetting goes back to factory settings) I was hoping there was a way to reconnect the router to the modem while retaining all the current security and settings.
View 2 Replies
View Related
Dec 10, 2012
Is there any physical or technical diferrences between PWR-3845 AC/2 and PWR-3845 AC? We are trying to order replacement parts and wondering if PWR-3845 AC is for one power supply and AC/2 means you get two with one order?
View 1 Replies
View Related
Dec 7, 2012
Is there any physical or technical diferrences between PWR-3845 AC/2 and PWR-3845 AC? We are trying to order replacement parts and if PWR-3845 AC is for one power supply and AC/2 means you get two with one order.
View 1 Replies
View Related
Jun 5, 2013
I'm running a cisco 891 with ios Version 15.2(4)M3 ,now I have a dialer 0 interface with fast0 and 1 as well, all is working fine.now I just read about the new sh int 'INT' history feature but when I do it I get nothing.. not a graph or anything I get just nothing as if I just hit enter.anything I need to do to enable the feature?,if I do a sho proc cpu history that works just fine but not the sh int XYZ history commands
View 2 Replies
View Related
Feb 24, 2012
have doubt, now my system is under my company domain,is there possible my network admin can watch my browser history
View 1 Replies
View Related
Jun 29, 2011
I have a lap top that someone else uses, is there anyway I can set some setting that erasing the history is not an opinion?
View 1 Replies
View Related
Oct 6, 2011
If I loose bookmarks on my Browser, can I contact my ISP for a log to my internet history?
View 7 Replies
View Related
Feb 25, 2013
How to clear history of cisco ASA 5520 ?
View 1 Replies
View Related
Mar 2, 2011
We are using the ASA 5520 as Firewall and VPN gateway for remote access by employees and vendors. Is there a way to view a history of VPN user logins? We used to have (or we still have but no longer using it) th CVPN 3005. This device keeps log files of all activities. I miss having this capability in the ASA 5520.
View 4 Replies
View Related
Nov 21, 2010
Our enterprise uses a VPN Concentrator 3000 for our VPN access. Is there a way to view a log history of what user connected to VPN and what IP address they were assigned? It would be for 2 days ago which was over the weekend.
View 3 Replies
View Related
Aug 29, 2012
I want to do something with IP SLA and started by estabilishing a baseline.
I'm trying to check history on an ASR. I tested same config on a 3845 and was forgetting the "history filter all". After this I could see history table on 3845 but still history is empty on the ASR1006. The operation started because I can see information with "show ip sla statistics".
know if i missed something or maybe this is not supported in ASR1006?
re-ld-tcc-02_ASR1006#show vers
Cisco IOS Software, IOS-XE Software (X86_64_LINUX_IOSD-ADVIPSERVICESK9-M), Version 15.2(1)S2, RELEASE SOFTWARE (fc1)
[Code]......
View 5 Replies
View Related
Nov 13, 2011
Having worked abroad, will my internet history be visible to IT when I reconnect my laptop to the company network?
View 2 Replies
View Related
Aug 11, 2011
how to track webhistory of a particular system using its ip address...can i remotely monitor the systems webhistory using its ip address.
View 5 Replies
View Related
Oct 1, 2011
I have been appointed to monitor an internet networking consist of 4 computers.
1. To block some websites for all 4 computers. Example, maybe if I want to block YouTube - Broadcast Yourself. or any website. This is actually to prevent users to access any adult site.I dont want to block internet entirely. But just to block some website only.
2. To have a report for internet URL for each computer. Not a bandwidth or traffic report. I dont need that. What I want is a list of URL that the user have surf in the internet.
View 1 Replies
View Related
