Cisco WAN :: Router 1841 - Way To Allow Specific Websites Access

Jan 25, 2011

Is there an easy way to allow specific websites access in cisco router 1841? I am trying to allow a website through access list 102 but not working. I am using access-list 102 permit ip host 192.168.21.20 host www.website.comIf i allow all websites then it works fine.

View 1 Replies


ADVERTISEMENT

Linksys Wireless Router :: WRT160Nv3 - Set Up Access Restrictions To Allow Only Specific Websites?

Sep 12, 2012

Possible to set up access restrictions to Allow only specific websites?

View 1 Replies View Related

Cisco Firewall :: RV120W - URL Blocking / Limit Internet Access To 1 Or 2 Specific Websites

Aug 18, 2011

My company has a peer to peer network of 10 personal computers without a server.  Operating systems from Windows XP to Vista.  I've recently installed a Cisco RV120W Wireless-N VPN Firewall.  It's configured in DHCP Server Mode with printers/copiers that have static IPs below the DHCP range.
 
I'm having a problem with certain stations being used for personal networking, shopping, etc. during business hours.  Consequently I would like to limit internet access on these stations.  However, some internet access is required because of online database software that's an integral part of our business.  I've been reading in the Administration Guide about URL Blocking.  Would it be possible to give static IPs to certain stations and then limit their internet access to 1 or 2 specific websites?
 
FYI, I've read about the Trusted Domains and Blocked Keywords but cannot quite understand how to parley this into the solution I need.

View 1 Replies View Related

Cisco WAN :: 1841 To Block Access To A Specific Interface

Feb 11, 2013

I have an 1841 between my firewall and the ISP.  Three interfaces - multilink to ISP, FA to my firewall, and FA to my inside network.  I use the inside interface for configs aand snmp access, etc.   Only my ISP-assigned fixed address block will get routed to the multilink by the ISP but I am nervous about the inside interface sitting on my LAN.   I know I can remove it, but if I keep it there, how can I set up an ACL so that all traffic from the multilink interface is denied to the inside interface?  I suppose another way to think about it that the inbound iface can only accept traffic from its own outside, not from the router.I think this is fairly simple but I don't want to knock down the traffic if I get it wrong.

View 8 Replies View Related

Blocking Websites Using Cisco Router 1841?

Feb 1, 2011

Can I configure a cisco router 1841 to block specific sites?

View 4 Replies View Related

Cisco WAN :: Some Websites Work Others Don't 1841 Router

Feb 18, 2011

just configured a 1841 router and im trying to figure out why some websites work and others dont - when i put in a small TP-LINK everything works fine so its not my ISP
 
my config:
 
Building configuration...
Current configuration : 3057 bytes!version 12.4service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname RT1841!boot-start-markerboot-end-marker!logging message-

[Code]....

View 6 Replies View Related

Cannot Connect To Specific Websites

Apr 14, 2011

I have two webites hosted by the same company. Yesterday I thought their server was down. To make a long story short, everyone I talk to can access the sites and I cant my hosting company says its a router problem. I contacted the service provider and reset the router but that didnt fix it. I have 3 computers on this router and none of them work to access the site. I reset the ip config, I've tryed EI and Firefox. I checked the IE diagnostic log but dont know what it means and it says:

0" ?>
<?xml-stylesheet type='text/xsl' href="xpnetdiag.xsl" ?>
<xpnetdiag>
<title>

[code]....

View 19 Replies View Related

Specific Connection To Use For Certain Websites Or Services?

Nov 13, 2011

I hope this question has not been asked here in the past, as I have googled for answers many times..I live in UAE and the ISP here blocks many sites and services which made me do the following:I have a notebook PC running WindowsXP with two connections to the internet.LAN connected to my ISP which is 30mb/sWLAN connected to the internet through DD-WRT router running OpenVPN and the speed is not that fast.hat I do now is that I have to disable my LAN and access the internet through WLAN (VPN) and have to enable LAN again whenever I need to download large files

View 5 Replies View Related

D-Link DIR-615 :: Blocking Not One Specific Website But All Websites?

May 16, 2013

In Setup > Parental Control it is possible to set rules attached to specific website URLs. I want to block access from 1am to 6am.

However these rules only apply to websites URL. Is there a way to apply a rule to ALL websites at once? I tried to enter "*" or "*.*" in website URL field but it doesn't work.

View 1 Replies View Related

D-Link DIR-655 :: Blocking Specific Computers On Lan From Websites?

Apr 28, 2011

Is there a way to block specific computers on the LAN from specific web sites by the domain name? All I can see is that if I put, for example, www.facebook.com, it will be blocked from all computers on the LAN, whereas if I want to block only 192.168.1.3 for example, I have to use the IP address through the Access Control, which is much harder and ****e to some "work around" by the user.

View 3 Replies View Related

Cisco WAN :: Allow Only Few Internet Websites From 1841

Jan 12, 2011

I need to allow only a few Internet websites from Cisco 1841 Router for my LAN users. What Access-List should be used for this.

View 4 Replies View Related

Cisco Switching/Routing :: 1841 - Connecting To Hosted Websites

Jan 10, 2013

Here's my setup:

 - Cisco 1841 connected to the internet on fa0/1
- LAN connected to fa0/0/1 (switch port, connected to Vlan1)
 
On my LAN I have a web server that houses different websites. Those websites have DNS records that point to my public IP address, located on fa0/1. From the outside I can reach the websites perfectly, but I can't reach them from the inside. So it looks like I can't seem to connect from my local LAN address to the public ip address on the Cisco (who then should NAT it to the correct server)
 
Here is a snippet from my config:
 
--NAT--
 ip nat inside source static tcp 192.168.0.3 80 interface FastEthernet0/1 80
ip nat inside source route-map Internet interface FastEthernet0/1 overload
 
--OUTSIDE INTERFACE--
 interface FastEthernet0/1
description WAN
ip address dhcp
ip access-group WAN-IN in
[ code]...
 
--INSIDE INTERFACE--
 interface Vlan1
description LAN
ip address 192.168.0.254 255.255.255.0
ip access-group LAN-IN in
[Code]....

View 3 Replies View Related

Cisco Security :: Block Access To Some Websites On 887 Router?

Jul 11, 2011

I went through all discussions regarding how to block access to some web sites. And I was trying to implement them but it didn't work. I've used 887G-3G-K9 router and UC540, and I'm not sure if it's possible to do that on them or I need to get a license for that or to buy  ASA. How can I check that URL blocking is available feature on those devices?
 
I've used 2 methods:

1) ACL
 
2) class-map and policy-map
 
class-map match-any http
match protocol http url "*facebook.com*"
match protocol http url "*www.facebook.com*"

[Code]....

View 1 Replies View Related

Linksys Wireless Router :: X3000 Can't Access Certain Websites

Dec 20, 2012

I installed a X3000 yesterday. I notice I can't access parts of certain websites - it seems to be just those parts of each site where a logon/password is required.My wireless dongle on the same laptop works OK, so it seems to be a router problem?

View 3 Replies View Related

Linksys Wireless Router :: EA4500 - Cannot Access Websites

Dec 24, 2012

Got a new EA4500 for Xmas. After setting up the new router I could only access you tube and Google at a very slow speed, however I can not access any other website - Facebook, yahoo and etc... it would ping yahoo and Google no problem friend told me to do a tracer to some ip address and his conclusion was the router is fully functional
 
ISP uses PPPoE, Im sure that the username and password are correct. upgraded to the latest firmware manually, and holy hell accessing the router with no internet access.

View 5 Replies View Related

Linksys Wireless Router :: Unable To Access Most Websites Using EA4500

Dec 4, 2012

I have had my router for about a month and all the wireless lan stuff seems to be brilliant. Recently I signed up to an ISP (Plusnet), and can't access most websites. The ISP has told me that I should take this up with my Router company. I seem to be having the exact same problems as this guy was having [url]....

View 1 Replies View Related

Linksys Wireless Router :: E4200 V2 Unable To Access Most Websites

May 24, 2012

I recently bought the E4200 v2. When I first installed, I ran the firmware update and then performed a hard reset (push reset button for 20 secs). I then began to enter all the PPPoE information and network settings into the new router (verified these settings with the existing WRT54GL router I'm current using and they all matched). I then disconnected the old router, and powered up the E4200. I was able to access the new router (192.168.0.1), I could see all previously shared files/computers with the new router, but I could not access most websites - usually I got a timeout error, or they eventually loaded in 10x the usual speed. This was typical of both laptops - one wired, and one wireless.  My wireless handheld device could connect to the wireless network, and ran a speeedtest.net test, and upload/download speeds were normal - but I could not access the internet from the device. When I switched back to the old router, everything worked perfectly again.  I have tried some suggestions on changing MTU values, but that did not seem to make any difference.
 
As a work-around, I have ended up keeping the WRT54GL as the main router and using the E4200 in bridged mode for wireless only (not what I ideally would like)..

View 4 Replies View Related

Linksys Wireless Router :: Unable To Access Most Websites With E4200

May 3, 2012

I've been on DSL with British Telcom Infnity (FTTC) since March and had no problems with the service.  My router,  however, an Apple Time Capsule, was not so reliable and needed a reboot every few days,So I just purchased the E4200 V2The Setup completes OK and PPPoE logs into my ISP fine.  But then I hit the problem.Most of the websites I use simply won't load . In Safari on my OS X Lion, Macbook, I get an error like this "Request Timeout. The server timed out while waiting for the browser's request. Reference #2.525fdd58.1336048435.0" In IE on my Windows XP laptop, the error is "Internet Explorer cannot display the webpage"But some websites still load fine.  So [url]..., loads instantly. Most other sites I try, including [url]... - won't load at all. (Plusnet is my ISP)If I connect to my work VPN, I can browse as normal

View 9 Replies View Related

Cannot Access A Specific Website Through Router On Any Computer?

Jan 4, 2012

So I have a really strange problem where I cannot access my credit union's website at all through any computer in my house. I've tried on 3 different laptops both Mac and PC, along with PC desktop and my iPhone.What's weird is that I can access the website on my iPhone if I turn off wifi and use 3G - no problems. But once I'm on the wireless network again it just loads for 20-30 seconds before saying it can't connect to the server. The URL is which I also checked on down for everyone or just me - the results came back immediately saying it's just me!t this point I literally have no idea what to do... tried resetting the router, logging into the admin via 192.168.1.1 and couldn't find any firewalls or blocked URLs. I'm fairly knowledgeable with computers and OS' but networking I'm no savant.

View 6 Replies View Related

Disable The Access To Specific Website On A Dlink Router DIR-655?

Sep 27, 2011

How to disable the access to a specific web site on a dlink router DIR-655

View 1 Replies View Related

Linksys Wireless Router - E1500 :: Unable To Access Certain Websites And Game Servers?

Feb 17, 2013

I've been having a strange intermitent problem with my E1500 wireless router.  When we first bought and installed it everything was working well with no known problems.  After several months no one using the router was able to access certain websites as well as a game server that we play on.  No one had made any changes to the router settings and I assumed at first that it was an ISP problem. After talking with our ISP tech support they finally suggested plugging my PC directly into the modem rather then the router. I did and found that the websites and servers that previously wouldn't connect while using the router were now reachable. Any changes to the router settings since installation.I decided that just in case someone unauthorized had made changes to simply revert the router to factory settings and reinstall the software.  After doing this I found that I could again reach the websites and servers that I previously could not. So time went on with no problems until a few months later when the same websites and servers were again unreachable by anyone on our router. I again reset the router to factory settings and changed passwords as a precaution, but this time the websites and servers were unreachable even though I had just reset the router. 

View 7 Replies View Related

Linksys Wireless Router :: EA4500 Don't Allow To Access A Specific Website?

May 18, 2012

I just bought the new EA4500 router and I'm experiencing problems to access the my bank website [URL] I can't access this website.
 
I thought that the problem could be with Comcast, but I tested my Mac with a cable directly connected into the cable modem and it worked fine. I was able to access every site.
 
It could be a problem with browser security, but I even tested with different computers (Mac, PC's, Ipad, Smartphones) and none of them were able to access the [URL] wirelessly.
 
It seems something strange with the router. I tested some forum solutions (MUT, QoS) but they didn't work.

View 2 Replies View Related

Throttling Specific Computers Access To Home Linksys WRT54GS Router?

Feb 1, 2013

I have a Linksys WRT54GS router that I have installed dd-wrt on.My household is overloaded with wireless devices, and living in a home of 6, speeds for everyone seem to slow down drastically later at night when everyone is simultaneously connected and streaming media -- whether it be Netflix, YouTube, etc.. My typical speed wired to the router with no other connections is around 25 mb/s down and 1-2 mb/s up.Obviously, it's going to slow to a crawl when we have an iPad, 3 iPod touches, an iPhone, a Wii (playing Netflix) and 4 PCs all connected simultaneously.What I need to do is give my personal computer priority and throttle all other devices. So that I myself will have decent speeds while hampering all of the other household connections. I rely on those speeds for my job and that should have priority over my brother watching music videos on YouTube.

View 1 Replies View Related

Linksys Wireless Router :: Cannot Restrict Specific Access Time On Valet M10

Sep 20, 2012

With M10, I cannot restrict internet access for specific time period. Parent Control feature doesn't satisfy the situation, and there is no build-in access-policy in web-based setup. Are you going to upgrade firmware or Cisco Connect with more flexible access time control?

View 1 Replies View Related

Linksys Wireless Router :: E3000 Possible To Limit Access For Specific Device (PC) To LAN Only

Dec 31, 2012

Within the Internet Access Policy section of the browser based utility, is it possible to limit access for a specific device (PC) to LAN only (not allow any traffic to external internet)?  I see that you can block internet access for a specific machine, however I didn't know if this was inclusive of LAN as well.If not, is there another way to achieve this via the E3000 or should I be looking for a solution on the specific PC itself? 

View 4 Replies View Related

Cisco WAN :: Setup Client VPN Access On 1841 Router

Nov 23, 2012

Trying to setup client VPN access on a 1841 router. essentially i would like to connect using  the cisco vpn application.

View 2 Replies View Related

Cisco VPN :: Setup Remote Access In 1841 Router?

Aug 12, 2012

I am trying to set up Remote access vpn in 1841 router. The vPN client is connecting to router, but cannot ping to remote LAN Here is the config.
  
Current configuration : 3625 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption

[code]....
 
I am not getting any hit on the deny statement of 102 when i try pinging to client ip address (10.0.0.10).

View 2 Replies View Related

Cisco WAN :: 1841 VPN Tunnel - Cannot Access Remote Lan From Router

Dec 15, 2010

I can ping across the tunnel from the pc's on either end of the tunnel, but I can't ping across the tunnel from the routers. If i ping using the source command using the LAN interface, the ping is successfull.
 
The reason i need this is for the remote router to be able to lookup the head office server for dns wins and ldap.

View 4 Replies View Related

Cannot Access Some Websites?

Feb 1, 2011

I am trying to access some websites and unable to do so

View 2 Replies View Related

Why Won't Pc Access Any Websites

Apr 13, 2011

When clicking the Internet Explorer icon it won't open ANY webpage. My Internet connection works perfectly. My other computers are fine.

View 1 Replies View Related

Can't Access Certain Websites

May 11, 2011

[url]...

I'm in Indore (India), whereas my friend from Mumbai can access them both.Also my ISP is Airtel.

View 3 Replies View Related

Cisco Firewall :: Cannot Access Certain Websites Behind PIX 501 With 6.2 FW

Oct 9, 2012

I have a PIX 501 with 6.2 FW.  The firewall inside network is connected to a Windows server (Mailserver).  I can get access to most websites on all clients as well as on the server.  However, there are some particular websites, such as facebook.com that the server and all but one client cannot access.  I get a "cannot display the webpage" in internet explorer.
 
I have disabled the Windows firewall and AV.  I have also scanned for any malware and no malware was found.
 
I found on the forums a "fixup protocol dns" solution, but my PIX version does not support it.
 
Below is my config:
 
PIX Version 6.2(2)
nameif ethernet0 outside security0
nameif ethernet1 inside security100

[Code]......

View 12 Replies View Related

Can't Access This Websites Message

Jan 13, 2013

Getting a message along the lines of: can't access this website when accessing certain websites such as the BBC and my university's intranet as well as random websites, also I can't access things like the online content on games such as far cry 3 or saints row 3.I've tried rebooting the router, I've tried the command prompt tracert, I've tried getting on other browsers with no avail and I've tried the other computers in my house and they've been getting on fine, tried full antivirus and malware scans and I've tried checking my firewall settings.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved