I tried to copy my conf file to a USBflash drive but I cannot initialize the USBflash drive.It asks me to format the USBflash, but when I say "yes" it gives an error.
Feb 21 11:18:40.799: %USBFLASH-5-CHANGE: usbflash1 has been inserted!
Feb 21 11:19:00.803: %USBFLASH-4-FORMAT: usbflash1 contains unexpected values in partition table or boot sector. Device needs formatting before use!
yourname#fort
yourname#for
yourname#format usb
[code]...
When I connect it to a 2811 its working perfectly
OOHQ_GWVO_01#sh usbflash0:No files on device
2116747264 bytes available (0 bytes used)
OOHQ_GWVO_01#dir usbflOOHQ_GWVO_01#dir usbflash0:Directory of usbflash0:/
No files in directory
2116747264 bytes total (2116747264 bytes free)OOHQ_GWVO_01#
I tried to copy my conf file to a USBflash drive but I cannot initialize the USBflash drive.
It asks me to format the USBflash, but when I say "yes" it gives an error.
Feb 21 11:18:40.799: %USBFLASH-5-CHANGE: usbflash1 has been inserted! Feb 21 11:19:00.803: %USBFLASH-4-FORMAT: usbflash1 contains unexpected values in partition table or boot sector. Device needs formatting before use!
i'm trying to find information about the licesing of ios package. I need to upgrade a C2911 from 15.1 to 15.2, the router have a permanent uc license, will be that license permanent also after the upgrade? I'm not able to find documentation about when the license need to be reissued after an upgrade or not. I know that for maintenance release upgrade there are not problems but i'm not sure about minor upgrade.
i had installed the SSL_VPN to the router C2911, running on IOS 15.0 But i couldn't see the SSL_VPN enable while i do show license feature? i did reload the router several time and accept the end user agreement.
attach the 01. show license feature 02. show license detail
We just received a new C2911 G2 ISR and have been trying to configure the EtherSwitch SM-ES2-24-P module on it. Through the router console, I tried assigning an IP address to the router Gi1/1 interface which I assume is the link to the Etherswitch module but all I'm getting is "IP addresses may not be configured on L2 links" - as per the docs, I should be able to assign an IP address on that "logical" interface link. Any other way for me to configure the ports on that switch module?
Two C2911 routers are connected to LAN and have HSRP configured. HSRP is negotiating successfully (active/standby), but LAN switch Enterasys Matrix E1 has problems accessing the virtual HSRP address. The switch can ping HSRP IP, and the virtual HSRP MAC is visible in its MAC table. But the static routes configured on the switch towards the HSRP IP seem to refuse working. Workaround to enable users to access network was to direct the static routes to the physical IP of one router. Is there a known incompatibility between Enterasys with Cisco HSRP?
XP Home edition, went to tools can't find working off line or working online to make sure off line is not checked so I can get on line DSL Verizon , Wireless router, wireless switch in on, on the cpu
A few days ago my internet suddenly stopped working. I plugged in the ethernet cord and everything worked fine. Checking the properties in the device manager showed the device was working properly, I also tried resetting it to make sure it was enabled but it did not work.
Upon troubleshooting, the "Windows Network Diagnostic" said the problems was that the Wireless adapter was not turned on. Using the switch on the front of the laptop as well as the function keys does nothing. Usually a graphic pops up showing if the WiFi is on or off, changinging transparent to show the WiFi is disabled. Now when I turn the switch on it always appears transparent, effectively going from off to off
So I know the computer reads both the function keys and the switch on the front but both methods never actually turns the adapter on. I just finished a system restore and nothing has changed
Today, while surfing the web my internet connection on my PC just randomly shuts off. I go check on my laptop and its normal. My WiFi says that I am connected to an Unidentified network with no internet access. So i got frustrated and checked all the forums and nothing seemed to work. So i restored my computer to factory settings and I still got this problem. Does this mean my Wifi Card is bad? Is it a virus? I can see other networks fine but i just cant connect to mine!
I need to know if I'm right about this. I have a customer that wants me to set up a dynamic-to-static IPsec tunnel between an 1811 router (dynamic) and an ASA with a static address.The catch is that the 1811 sits behind an ISPs cable modem where it picks up a private 192.168.x.x address.
Is there any other way to make this work where the router with the dynamic IP is sitting behind a box that's doing PAT translations?
I've recently been tasked with providing access to several internal servers to a remote site via one of our ASAs. In order to keep things simple, I have begun by creating a single static NAT rule for one of the servers. The Site-to-Site VPN connection profile was then created and testing has begun. Unfortunately it looks as though the NAT rule isn't working. As I monitor the tunnel, I still see our internal number being broadcasted and not the mapped address, which prevents the tunnel from being established. The remote site has verified that this is what they are seeing too.
Appliance: ASA 5510 ASA 8.4(2) ASDM 6.4(5)
Address Legend: (Note: The following addresses are not actual addresses.) [Code]...
I have been trying to get my FTP server working for months with no joy. It works when I connect to it internally but not from outside. If I do a port scan, I can see that port 21 is open. I tried it with disabled firewalls and also checked with ISP that nothing is being blocked. I have attached the config file. I used several differnet FTP servers such as CoreFTP, Wing FTP etc.
why the following configuration is not working? I have two clustered ASAs inline from one another, in front of a 4506-E switch in front of a host I want to access via RDP, like so: My issue at this stage lies with getting the UNTRUST firewall configured. I've tried the following configuration 1) Creating the host.
I am trying to use a Dell FTRJ8519P1BNL SFP fiber module in a Cisco Catalyst 3560 and have already run these commands: no errdisable detect cause gbic-invalid service unsupported-transceiver.But I STILL am getting these errors even after shut/no shut on the port.
I am have unabled the cisco SDM on my pc, and able to get the http for my router 1841:I have done below configuraiton in my R1841[code] why I am not able to get the above commands, and does my SDM not work due to this or anything else need to be done?
I've got a new 891 to replace an old 837 and I'm struggling to get the dynamic nat pool working.I've successfully configured the dialer etc for PPPoE and when I set up a static NAT translation between my PC and an external address then I can ping hosts on the internet e.g. ping 8.8.8.8 successfully. But when I remove the static translation and try and use the dynamic NAT pool then no NAT translations take place, and show ip nat translations only shows the other static entries.The relevant bits of the config are below and I've also attached a full (cleaned) config.
ip nat pool TestPool 81.2.123.226 81.2.123.226 netmask 255.255.255.248 ip nat inside source list 15 pool TestPool overload ! Can only access internet when static route is defined for my PC ! If I remove this line then it doesn't use the dymnamic pool TestPool ip nat inside source static 172.16.0.11 81.2.123.226
i have a 876 Router, connected to the Internet and a VPN. From inside i would like to pass all traffic destinied to 192.168.0.0 255.255.255.0 to the VirtualPPP IF and al the other to the Internet (vlan2) I have created this rule, but after applying ist works only for about 30 to 60 seconds. after that only the Internet reachable. Everytime i do a clear ip nat trans * both Interfaces will work für 30 to 60 secs again...
We have an ASA running 8.2.2 (adsm 6.2.5). VPN connections are working well.But it's not possible to use a SIP client (phone or software) through an SSL tunnel.So today I've tried to look in detail on this problem. I installed an ubuntu system,openconnect and ekiga as softphone. In our network everything is working without any error. I used an external DSL connection to test everything over the VPN tunnel.I can ping the SIP server and I can access the https frontend of the the SIP Server.The client "seem's" to connect as well. I can call the ekiga client, it's ringing and i can speak and hear everything (most times).Dialing from the ekiga client ALWAYS fails. On the ASA there is no policy allowing or denying those connections. How can I trace it on the ASA ?
I have ASA 5505 with outside interface IP 206.206.206.5 I configured the SSL vpn on this but still i am getting page can not be displaed when opening https://206.206.206.5 from broadband.
Below is the related configuration in ASA. What needs to be done in order to able to connect SSL vpn.
we have installed a new appliance of LMS 4.2.2 in our VmWare environment. The platform is running licensed to work with 1300 devices. We have approximately 500 devices in DCR, most of them are small switches ranging from Catalyst 2950 to Catalyst 3750, and also a bunch of Nexus 5548 switches.CiscoView is not working for any of them, we get an error message which we cannot interpret. We have updated to the newest possible device packages, but all to no avail.
I have configured my Cisco 881 and it is quite stable but now I am working on some minor details.
I have several Public WAN IP addresses which are NATing to internal web server. When I go to the WAN IP at port 80 from the Internet, the NAT works fine and it maps perfectly to the internal Web server. However, when I try the same same WAN IP from the LAN which contains the web server, the Router blocks the traffic and I get nothing back.
I have verified that I can get to the Inernet from the LAN but it seems that I cannot go bfrom the LAN to the Internet and back into the LAN via NAT.
I got a question about ACS 5.3 and WLC We have now the ACS 5.3 running for MAB (good working) and TACAS for device AAA.But now our WLC’s will not work.I have created already a special “custom attribute” => role1 / mandatory / ALL Already changed to the combinations Role1=ALL / Role1=All / Role1=all / role1=ALL / role1=All / role1=all But still not working. I get a wrong response.
what ios for 827-4v from 12.4 can i use for IPSEC+ddns?i tested some from 12.4 but normally working only 12.3(26)GD, but i want ddns feature? some from 12.4 is working with tracebacks, other is not loading - with error (loadprog: error - program section linked to illegal address)
I am having issues with running IS-IS between my ASR9006 and Cat6500 switch.I am running IOS XR 4.0.3 with Mini and MPLS packages enabled. My configuration on ASR is below, does configuration on the ASR9000 is correct and why its not working? [code] .....
I am setting up ssh on my 871 router and I get prompted for only a password. I have typed in the correct password and it doesnt let me in. I also have telnet enabled and with telnet I do get prompted for both username and password and I am able to login. I would like to setup ssh so that it used the local username and password. This is what my vty has.
line vty 0 4 access-class 23 in privilege level 15 login transport input telnet ssh
My network is currently running with SNMP v2 configured in easch devices. With snmp v2 our LMS 3.2 server is working fine. However we have planned to migrate our network to snmp v3 . I have configured my few devices for SNMP v3 and added them to my LMS server.
Except DFM module these new SNMP v3 devices are working fine in all other modules. In DFM these devices are reflecting under "snmp timeout" group. I checked with device center -> management station to device; where the SNMP v3 connections are showing "okey"
following are tyhe configuration i have done in my devices.
snmp-server group v3g v3 priv read testr write testw snmp-server user v3u v3g v3 auth md5 test123 snmp-server view testr iso in
I have a 837 that I'm getting setup for a charitable cause. I copied most of another operation setup but am having issues with the routing, I think.
THe ATM appears to be correct using the "ping atm interface 0 0 35 end-loopback" command.
I have pasted the run-config below:
version 12.3 no service pad service tcp-keepalives-in service tcp-keepalives-out service timestamps debug datetime msec localtime show-timezone service timestamps log datetime msec localtime show-timezone service password-encryption service sequence-numbers(code)
