There are no commands like route-map & ip sla monitor on my cisco 1841 router, its ios version is 12.4(T1). I have to configure load balancing and failover on this router but without these commands i cant do that.
View 3 RepliesI have cisco 2911 with IOS-universalK9 mz.SPA.150.1.T, but that does not accept the ip sla monitor commands XX, XX or rtr ip sla XX. How active these commands in IOS or what you belong to?
View 1 Replies View RelatedI have two nic one connected with DSL modem with gateway 192.168.1.1 for Internet. another nic connected with office Intranet with gateway 10.226.122.x . I can connect only one network at a time disabling other.. I know route add command can be used for linking the both network so I can simultaneously use Internet and Intranet..can you elaborate with example (five years ago I set up the same with route add command.. now my memory failing..)
View 1 Replies View RelatedI have an old 2621xm router in CCIE lab at home. Only a week ago I started having issue on 2 of them. The problem is on one of them when I go under interface configuration and I type "no shut" nothing happens. Interface stays in administratively down status and when I check running config "shutdown" is still under interface.
On the other one the same problem but only with "router rip" command. I configure my rip routing but then when I check running config there is no rip section and also RIP is not running under "show ip protocols rip".These routers are connected to 2511 AccesServer. So I thought the issue might be communication from AccessServer to these devices. I connected a console cable straight to them and still the same problem. Everything else is working on these devices.
I want to know with an ASA 5505 w/ Security Plus License I get up to 20 VLANS/Named Interfaces.I have a customer that is getting a new subnet of external IP addresses from their service provider and a different default gateway to accomodate re-hosting their datacenter at their main office instead of at a Colo. My question, when building out their new DMZ, can I have multiple route 0.0.0.0 commands?
Example.
Current Default Gateway 1.1.1.X
Internal hosts 192.168.1.0 use and are natted to 1.1.1.X
New Default Gateway for DMZ Servers 2.2.2.x
Internal hosts still use 1.1.1.X, but server hosts in 192.168.1.3 should use 2.2.2.X -- there are also a bunch of pre-existing static NAT rules for these servers such as 2.2.2.30 translates to 192.168.1.30.
I think I would accomplish this by using the following:
route inside 0.0.0.0 0.0.0.0 1.1.1.X
route DMZ 0.0.0.0 0.0.0.0 2.2.2.x
Would this be correct?
I used the GRE tunnel site to site VPN with 2 cisco 1841 routers. Behind one of the router R1, I used cisco ASA 5510, now my vpn is connect between two routers, but from R2 other site cannot access to LAN behind the firewall. From R1, also cannot route to local network, from local network can access to R1, I think cause of NAT . So how to configure to route internal network from R1 & R2 with VPN.
View 5 Replies View RelatedIt is required to monitor newly placed WAN link performance . How can I configure my cisco 1841 router to obtain the following information.
1) Errors
2) Jitter
Belkin Setup / Router monitor application has stopped working. A problem caused the program to stop working correctly. Windows will close the program and notify you if a solution is available.
View 1 Replies View RelatedMy Belkin N150 wireless router monitor has stopped working. A problem caused the program to stop working correctly. Windows will close the program and notify you us a solution is available.I can not figure out why my wireless router doesn't work sometimes.I need to be able to access this to get to the router settings. I don't know if my wireless is being highjacked or what.
View 2 Replies View RelatedWe have a Cisco 1841 router and checked something an unnusual (never seen before) routing table having L - local routes. if this an IOS bug or same as C - connected local routes.
1841#sh verCisco IOS Software,
1841 Software (C1841-IPBASE-M),
Version 15.0(1)M3, RELEASE SOFTWARE (fc2)Technical Support: [URL] ... Copyright (c) 1986-2010 by Cisco Systems, Inc.Compiled Sun 18-Jul-10 01:16 by prod_rel_team
[Code] .....
VPN 1841, and static nat. I have to create VPN to connect to remote network, but problem is that they already use same subnet as mine. How to configure static nat on cisco 1841 so static nat will work and address will be translated in different IP when connection trough VPN.I have address 192.168.235.1 and I want to translate to 192.168.100.1,This 1841 is border router, and all VLNAs and VLANs routing is on 3650.
View 12 Replies View RelatedI am trying to set up a SLA statement on an ASA 5505 version 8.2(5). When I enter the command "sla monitor schedule 1 life forever start-time now" I get a message stating "%Entry not configured."
View 1 Replies View RelatedOne of the route maps doesnt want to work, all the other are fine -
route-map vlan23-out permit 40
match ip address 123
set ip next-hop 87.194.168.1
If it take the ip policy off interface gi0/0.123 the client can access the internet OK but over the wrong ISP?As soon as i add the policy all internet stops
I have a Cisco 1841 with a DSL and 3G HWIC interface. I would like to setup the DSL as the primary link and then use the 3G as a backup interface. I am trying to accomplish this using the Floating Static routes with SLA object tracking.
I have tried various options, like having two tracked routes, one tracked route, changing administrative distances, multiple SLA's, etc etc.
My problem basically is that when the DSL (Dialer0) goes down and the 3G (Cellular0/1/0) takes over, that the SLA never changes back when the DSL is available again, so that the DSL can take over as the primary link again. [code]
I have a Cisco 2811 router and i want to experiment on the IOS firewall.The thing is, none of the commands that are proposed in online guides - like ip inspect, ip audit, etc. - seem to be working. I just get "unrecognized command" on a router that is supposed to support such features. I'm wondering if it has something to do with the IOS image.
My show version output is this:
Cisco IOS Software, 2800 Software (C2800NM-SPSERVICESK9-M), Version 12.3(11)T9, RELEASE SOFTWARE (fc3)
Technical Support: [URL]
Copyright (c) 1986-2005 by Cisco Systems, Inc.
Compiled Tue 13-Dec-05 08:24 by ccai
[code]....
I've got an existing Cisco 1841 connecting to a 10Mbps Internet Leased line. With my current setup I've configured PAT for internet access for my users, and we also have some servers on site which are assigned public ip addresses, these can be accessed from the internet. Now we have procured a Cisco 1921 ISR to replace the old 1841, when I connect the 1921 with an identical configuration in place of the old router, 2 things happen.
1) The users accessing the net via the nat are able to work without any inconvenience (good)
2) My servers which have public IP addresses are unable to reach the internet and subsequently I am unable to reach them via the internet (very bad)
The host IP 84.204.x.x unable to announce through BGP
BGP configuration on Cisco 1841:
!
interface FastEthernet0.1201
encapsulation dot1Q 1201
ip address 172.18.11.1 255.255.255.252
no ip redirects
no ip unreachables
no ip proxy-arp
code]....
I have a 1841 with 12.4(16) IOS.In my configuration I have to interfaces for internet access, without vrf:
interface ATM0/0/0
dsl operating-mode auto
pvc 8/35
encapsulation aal5mux ppp dialer
dialer pool-member 1
[code]....
This two interfaces are in the global route table because there is no vrf indication. These are for internet access (a simple adsl connection) Then, I have this interface in VRF named "lan123"
interface FastEthernet0/1.23
encapsulation dot1Q 123
ip vrf forwarding lan123
ip address 192.168.143.254 255.255.255.0
ip nat enable
Now the issue.If I write:
ip route vrf lan123 0.0.0.0 0.0.0.0 Dialer0
this works and, with nat, internet works. The question is why this works without the "global" keyword? I'm going from the vrf named "lan123" routing table to global table without the using of "global" keyword.
If I try to use:
ip route vrf lan123 0.0.0.0 0.0.0.0 Dialer0 global
there is an error indication.
Basically I have an internet router (1841ISR) with 1 internal (LAN) connection and 2 internet connections. What I want to do is route specific traffic for 3 of my internally hosted services (smtp, https, etc) through one internet connection (fa0/0) and then route all other traffic through the unmanaged/dynamic IP ADSL connection (Dialer 0).
View 9 Replies View RelatedI've setup and configured the following local monitor session on a 7606 but it doesnt seem to be outputing anything. Any guess as to why, or what I might be doing wrong? Gi1/1 is doing ~40Mb/s egress & 15Mb/s ingress. Both source and destination ports are routed ports.
monitor session 10 source interface Gi1/1
monitor session 10 destination interface Gi1/10 ingress
interface GigabitEthernet1/1
description WAN Link to ********************* ** CORE BACKBONE **
mtu 9000
ip address ************** 255.255.255.252
[code].....
the Dlink Network Monitoring widget just shows: IP Address error?I'm on DIR-655 Rev_B hardware and 2.01 firmware.
View 1 Replies View RelatedEEM script. I have tried below script on 1841 with 12.4(24)T5 but not working
snmp-server enable traps ipsla
snmp-server enable traps event-manager
ip sla 10
[Code].....
I want to try ping remote ip every 5 mins , if ping fails wait for 3 mins then trigger reload , and router come up again if ping fails reload again.
my problem in configuring a cisco 1841 as VPN server using SDM, everytime i press Lunch Easy VPN Wizard botton, there were no response at all. my IOS is:
Cisco IOS Software, 1841 Software (C1841-ADVIPSERVICESK9-M), Version 12.4(15)T15, RELEASE SOFTWARE (fc3)
ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
System image file is "flash:c1841-advipservicesk9-mz.124-15.T15.bin
by the way I took this IOS to other router with the same model(CISCO1841).
After command clear route, all timers just continue, there is not actually clearing the routing table... This is happening on two different boxes: pair of ASA 5520 and one 5505 ASA... I presume it is happening on all others too, but I don't have this release installed anywhere else...
Codes:
C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route(code)
I have configured a Cisco router. I am able to ping google from rotuer. I can ping my local IP from router and router local IP to my machine. But I can not access internet on machine. I can not ping google and any other IP out of network.
View 11 Replies View RelatedI have setup a remote access on our 1841 device, with split tunnel.
now i am able to connect via the vpn tunnel, and even ping and telnet into the cisco device, but when i try to ping any device past the 1841, the ping fails and no traffic is even been encrypted to go over the vpn traffic (looking at the vpn client statistics).
From the ciscos side, pings to the vpn client is failing, yet i see the vpn client in the routing table.
Here is my config:
cisco1841#sh run Building configuration...
Current configuration : 7682 bytes!version 12.4service timestamps debug datetime msecservice timestamps log datetime msecservice password-encryption!hostname cisco1841!boot-start-markerboot-end-marker!logging buffered 51200
[Code].....
I have issues with port forwarding. I did, but it didn't work. Then I tried different ip addresses. Now I don't know how to delete those configurations, because when I try to overwrite it says already exist. And still port forwarding is not working. I did: ip nat inside source static tcp (ip and port numbers)Our device is 1841, also we have firewall within this router. DHCP is in our 3750.
View 9 Replies View RelatedI have problem with icmp traceroute configuration. When I enabling icmp error inspection in global policy, my traceroute results through ASA 8.2.4 looks like this: My traceroute [v0.75]
icmp inspection and ttl decrement on ASA is enabled. Also I configured ACL on outside interface to permit ICMP completely.
I have configured Cisco 1841 router PAT buts its not worked, find the below configuration details,
In LAN interface
Interface gigabit Ethernet 0/0
no shutdown
[code]......
Similarly I have configured static and dynamic nat but its not works in my customer place.
Are the IOS commands the same on a router and a ASA for these two topics....CBT Nuggets where I train has 553 videos for some of the new topics. I am preparing for 554 as it has more ASA focus and thats more interesting to me.
View 1 Replies View RelatedI have created a baseline template to run compliancy checks, I understand that lines beginning with a + are mandatory and lines begining with a - should not be on the router. What I need to know is, is there a catch all for any other commands on the router config (startup or running) but not mentioned in the baseline? For example, lets say this is my baseline:
+ service timestamps debug datetime msec
+ service timestamps log datetime msec
+ service password-encryption
+ hostname [hostname]
The router comes back as compliant as it has all the above lines. However there is obviously more config on the router, but this doesn't show? So I know I can get commands that are in the baseline but not on the router; but what about the other way round - on the router but not on the baseline? Surely this exists - at the least from a security point of view, an attacker could well have configured the Dot11Radio int, however without entering the command with the minus prefix I can't tell? LMS 2.6
I have just received a new cisco 2901 and started on its configuration. when I started configuring VPN tunnels, I saw that non of the crypto commands are available.
The router runs on iOS 15.1.From what I read, people refer that the router needs to past a license activation or something like that. When I run show verison - i do see "none" under most of the categories.
I was attempting to setup our 7204 Cisco router to use RADIUS for authentication via the AAA commands. I must have messed up when configuring it as it comes up via TELNET asking for a username and password but doesn't take my AD credentials. How might I login to this router to fix the config? Do I need to do a password recover process?
One note, I didn't save the running-config to startup-config, so if I restart the router will it load the startup-config, thus overwriting the running-config that wasn't working?