Cisco Wireless :: 1310 Bridges Keep Losing Connection?
Nov 28, 2010
I have two 1310 bridges...one set as root and the other as non-root.For some reason they keep losing connection. When I reboot the non-root bridge, link is established.Both bridges have an antenna connected with the right connector and they have the setting antenna transmit right antenna receive right
logs from root bridge
Nov 29 13:52:53.311: %DOT11-4-MAXRETRIES: Packet to client XXXX.XXXX.XXXX reached max retries, removing the clientNov 29 13:52:53.311: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station XXXX.XXXX.XXXX Reason: Previous authentication no longer validNov 29 13:52:53.568: %DOT11-6-ASSOC: Interface Dot11Radio0, Station Test XXX.XXXX.XXXX Reassociated KEY_MGMT[WPAv2 PSK]Nov 29 13:55:16.260: %DOT11-4-MAXRETRIES: Packet to client XXXX.XXXX.XXXX reached max retries, removing the clientNov 29 13:55:16.260: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station XXXX.XXXX.XXXX Reason: Previous authentication no longer validNov 29 13:55:16.550: %DOT11-4-MAXRETRIES: Packet to client XXXX.XXXX.XXXX reached max retries, removing the clientNov 29 13:55:16.550: Client XXXX.XXXX.XXXX failed: reached maximum retries
logs from non-root Nov 29 2010 13:52:55: %DOT11-4-UPLINK_DOWN: Interface Dot11Radio0, parent lost: Received deauthenticate (2) not validNov 29 2010 13:52:55: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down The signal strength is around -84dBm Cisco IOS Software on both bridges is: C1310 Software (C1310-K9W7-M), Version 12.4(10b)JA1, RELEASE SOFTWARE (fc2)
View 12 Replies
ADVERTISEMENT
Jul 10, 2012
I have 2 campuses. I have my 5508 wireless controller working beautifully on my main campus using LDAP. (YAY!!) Now for my problem. My remote campus has 1310 bridges. I was able to successfully upgrade one of them to work with the controller, however, I can't get the other two bridges to talk to the one that I upgraded and I can't get them to upgrade, it indicates that they need to be the root. I have several small buildings on that remote campus, than need that remote bridging in order to be able to have network access.
View 7 Replies
View Related
Mar 2, 2011
I have two 1310 bridges. one configured as root and the other as non-root. Authentication Settings: Open with EAP and Network EAP with no addition. Set up: when non-root bridge tries to associate with root bridge, root bridge checks with radius server if it's ok to associate with the non-root bridge.
I can see communication with the radius server (I'm using FreeRadius) and the radius server even sends a SUCCESS back to the root bridge. However I'm seeing this error on the non-root bridge: DOT1X_SHIM-3-PLUMB_KEY_ERR: Unable to plumb keys - Eap key struct is NULL and the bridges do not authenticate.
View 2 Replies
View Related
Jul 19, 2012
I have a Problem with a customer WLAN. The customer has a Aeronet 1130AG AP. Now i should configure a Aironet 1130 Repater for this WLAN. The initial connection from the Repater with the AP is no Problem. But after some time the Repeater lost the connection. On the AP i see following Messages:20Jul 19 19:05:28.061InformationInterface Dot11Radio0, Deauthenticating Station xxx Reason: Previous authentication no longer valid 21Jul 19 19:05:28.061WarningPacket to client xxx reached max retries, removing the client 22Jul 19 16:43:59.412InformationInterface Dot11Radio0, Station yyy Associated to Parent xxx23Jul 19 16:43:57.901InformationInterface Dot11Radio0, Deauthenticating Station yyy 24Jul 19 16:43:56.536InformationInterface Dot11Radio0, Station yyy Associated to Parent xxx 25Jul 19 16:43:51.555InformationInterface Dot11Radio0, Station zzz Associated KEY_MGMT[WPA PSK] 26Jul 19 16:43:29.078InformationInterface Dot11Radio0, Station Repeater01 xxx Associated KEY_MGMT[WPA PSK]
View 2 Replies
View Related
Feb 11, 2012
My D-link wireless router (WBR-1310) keeps dropping my internet/email connection. The little green lights are all flashing intermittently except of the one on the far left which stays on. I will have a connection for a little while/few minutes and then it drops.
View 3 Replies
View Related
Jan 7, 2012
I have just started using my D-Link 1310 Router after quite a few years of it laying around. I managed to get as far as connecting my D820 and my Desktop in a basic Network. I have Windows XP Home on both the Desktop and Laptop. The next step I want to accomplish is making the Laptop wireless with my apartment. When I first had the Router, I of course had Technical Support and my Warranty with Dell was still active, so I was walked through the process and took notes. The only file I made note of for this step was installing the driver (US) WLAN Card Rev.A12, but there must be something else that enables the WiFi catcher because I don't have any icon in the System Tray and no way to access it.
I also remember it being necessary to Bridge the Modem and Router, (I believe we did it from the Verizon site). Though I was told recently that Bridging is not used anymore, now they do a thing called "Double Netting"?
View 1 Replies
View Related
Nov 15, 2012
I have an Acer 7750G, running Windows 7,connected to our home network using a Dynex router. At the moment this is the only laptop in the house that is having problems with connectivity. Starting yesterday, it only connects intermittently. When I run diagnostics, it says the following problems have been fixed but it either solves the problem for a few minutes only or not at all: "Problem with wireless adapter or access point" or "Default gateway is not available".
IPV6 connectivity also shows 'no internet access' and sometimes IPV4 reports no internet. I've unplugged and rebooted the modem and router a few times but that hasn't solved the problem.
Edit: I ran troubleshoot again, and it says the following issue is not fixed: "Wireless Network Connection 2 does not have a valid IP configuration".
View 14 Replies
View Related
May 20, 2012
I have cisco 1310 bridge with IOS version Version 12.3(7)JA5. Sometimes bridges are disconnecting by showing the following error message.
*Mar 1 01:22:21.856: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 003a.99eb.cc00 Reason: Previous authentication no longer valid
*Mar 1 01:22:22.115: %DOT11-4-MAXRETRIES: Packet to client 003a.99eb.cc00 reached max retries, removing the client
[Code]....
Once it is deassossiated, ihave to manually restart the bridges. How can avoid manual restarting so it would automatically associate after some time.
View 14 Replies
View Related
May 30, 2012
So my boyfriend and I just moved and, after struggling with our old wireless router we haven't used in years (pretty sure it was dead), we bought a whole new one in the hopes that starting from scratch would be simpler. It's a Netgear and we were aiming to hook up three devices through it; my laptop, his computer, and our Xbox 360.
He hooked it up no problem and we were using wifi for our computers and one ethernet cable through the router into the Xbox, peach as pie... Except my Toshiba laptop decided to rebel and allow me to use the internet for about five minutes before claiming there's "no internet." The signal says excellent and the little alert symbol keeps appearing and disappearing, but no pages will load. I tried running troubleshooting, but it couldn't identify the problem. Shutting down my laptop and turning it back on seems to be the only way to get it going again for another five minutes until the cycle continues.
View 2 Replies
View Related
May 1, 2012
Im having problems with some toshiba laptops that arnt showing the SSID for some wireless points in the school. We have had the waps set up with the same ssid so we can walk around and the laptops will connect from one to the other. Its been like this for sometime however some new laptops we have got running windows 7 pro show some of the waps up as "other network" - File attached. The actual SSID on ALL waps is Peel Park WiFi Therefore it keeps losing connection to the wireless points and wont connect to some.
View 5 Replies
View Related
Oct 8, 2011
I am running the below rig and connecting wirelessly via my DSL Router to my Blu-ray player which is connected via HDMI to my TV. Using Windows Media Center I have been recording shows via an OTA antenna. They are in .wtv format and going on the 500GB HDD. Playing these files on my TV has been going well until this week. During playback we frequently lose the connection. I have tried power cycling the router and the player, re-entering my settings in the player and connecting via Cat 6 cable. The only clues I have are that I recently did a second firmware update on my player (did not occur immediately after that) and I sometimes get the following message on the computer... Media Foundation Protected Pipeline EXE has stopped working.
[code]...
View 1 Replies
View Related
Mar 5, 2011
It seems to happen only when connected through our rooms or through wireless. When I connect directly to the router I don't lose connection. The router is downstairs and it routes the wired connection through a switch. So when routing through the switch or using wireless the connection is lost and re-connects about every 30 seconds to 1 minute. When directly connected it works fine. I've reset the router and reset all settings twice and nothing. I'm using 10/100. Not sure if any of this matters. I have also updated the firmware to 1.35NA. PPPOE password and username are correct as they have been given by our ISP. Any settings I should be aware of? Everything is pretty much default. All I do is setup the internet connection and then setup a wireless connection. Are we overloading the system maybe? I've also changed the password a few times as well. Seems like the logs fill up really fast. Keep getting blocked UDP and TCP packets from different addresses.
View 3 Replies
View Related
Oct 23, 2011
I have a Cisco Aironet c where it is configured as an AP. I use a Pocket PC to access the AP, but after a period of use, the Pocket PC loses communication with the AP for a short period of time and the application that is utilized in the pocket closes. After a few seconds it automatically connects. Searching the logs of the AP found the following warning: "Packet to client 0017.2302.8a5e Reached max retries, removing the client", but this is not always alert appears.
View 0 Replies
View Related
Nov 5, 2012
I have a problem with myself a few other clients randomly disconnecting from my 871W. It appears that I am still associated but Windows 7 shows "Limited Access". I appear to be assosciated to the AP and I still have my ip address but I can't ping the 192.168.1.1 gateway (871W). I have also set my power plan to allow for Maximum Performance which I thought disabled PSP but the log is still showing errors.As a final note, after I reconnected by ip address (192.168.1.107) doesn't show up in "sh ip dhcp bindings" but I'm working.To correct the situation, I have to disconnect and the reconnect to the AP and then I am good for another day or close to it. Below are the log errors, config and a sh ver. [code]
View 7 Replies
View Related
Apr 20, 2013
I have installed a wired and wireless connection for a compound which is around150 squire meters. I used the Cisco wap4410n routers for the wireless setup.
The structure is like this.There is a connection coming from the service provider. There is a central switch where the connection coming from service provider, the server, one Cisco wap4410n router and other two switches are directly connected to it. Again I connected other switches to the switches getting connection from the central switch. I used Cat 5e and Cat 6 cables to connect the switches as well as the wireless routers (For more info , the cable goes underground) and I used cross-over cable to connect switch to switch and straight-through to connect routers to switches. I connected the other Cisco wap4410n routers to the switches outside( I get like 6 Cisco wap4410n routers)The wireless routers are connected to the switches which are connected to the central switch and also on the other switches.
The routers are configured to have their default AP mode.My problem The connection is very slow. The connection is down almost every week and it needs to be re-configured. The connection nice on the router which is directly connected to the central switch(but not the same on the others routers which are connected to the other switches)even when I reset them they don't fall to .245 ( which is ok I can see them on the DHCP server but I still see it as problem)when I set them as a wireless wireless repeater, full signal but no connection(given that I have set same SSID, enabled allow wireless signal to be repeated, filling MAC addresses) Down here I have tried to show the architecture diagrammatically.
View 2 Replies
View Related
Feb 2, 2011
I have configured Cisco 2801 with HWIC-3G-GSM to work as a GPRS router.
The configuration is:
chat-script gsm "" "atdt*99***1#" TIMEOUT 60 "CONNECT" chat-script pin "" "at+cpin=xxxx" interface Cellular0/1/0 ip address negotiated ip virtual-reassembly encapsulation ppp dialer in-band dialer pool-member 1 dialer-group 1 async
[Code].....
View 10 Replies
View Related
Sep 7, 2011
We've had this AP for just over a year and just recently it started dropping its wireless connection. To fix, I have to and unplug the power and then plug it back in.. Then it works again for a few hours and drops out again. If I navigate to the config page right after it drops, all of the settings seem to be completely gone. But if I go through and unplug/plug it in again, all of the settings are back.
I updated the firmware to 2.0.4.2, but that didn't seem to resolve the problem. Is this thing a brick now?
View 7 Replies
View Related
Sep 12, 2011
linksys router problems Linksys wireless router connected to cable modem. over time router looses connection to internet. rebooting router reestablishes connection. running XP sp3 from laptop connected wirelessly?
View 3 Replies
View Related
Nov 5, 2011
I recently bought a iMac and it has been fine apart from the wi-fi connection.It used to disconnect me for 2-4 minutes every now and then at first and then this died down, but recently it keeps losing connection altogether. When I go on run diagnostics it says that i have failed to connect to the ISP and internet.Is there anyway to fix this?,I use a Netgear router with an Apple iMac running with OS X Lion
View 2 Replies
View Related
Jun 13, 2011
my Intel wireless card keeps losing the connection. Until a couple of weeks ago it would be fine for roughly the first 20 minutes then the connection would just completely drop out and the only way to get it back again is to go into the network and sharing centre, disable the network card and then reenable it. Most of the time this works, but again for only the first 20-30 minutes, then I have to do it again. Occasionally it works for for longer but that's a rare occasion.Now not only does it do this, but also, if I put my laptop into sleep, sometimes when I turn it back on again the card will not connect to the network and I have to do the same disable and enable process.[ODE]
View 7 Replies
View Related
Jan 25, 2012
When using my pc through my wireless Netgear router, the connection is lost periodically and I get the message "default gateway not accessible". It only happens on my PC, and not on my IPad. What should I do to keep the connection on my PC?
View 1 Replies
View Related
Jan 24, 2012
Im currently living downstairs from the router. Its in a "secure location." Long story short, the person I live with is very private about the particular room its located in. I know the router is a "N" model Linkys.I installed the software that came with the PCI adapter (NETGEAR N300) and everything seemed smooth, then I constantly kept dropping connection. I then assumed the driver needed updating so I uninstalled the driver and re-downloaded the recommended driver from the netgear website,Things to know:
-I don't do any heavy gaming
-When I disable and reable the PCI adapter driver from device manager I can reconnect to the internet rather quickly.
-When uploading a video to youtube I found the connection to be more stable, but slower. (could of been a coincidence)
Currently I've been running "TCP view" to try to find something in the background taking bandwidth. I searched all the applications that it lists and nothing seems to be abnormal.
View 4 Replies
View Related
Feb 3, 2012
I have a D-Link WBR-1310 modem and for some reason the internet connection drops every 4-5 minutes and then comes back after 30 seconds.I don't know what the problem is. I tried resetting the modem which didn't work. I tried upgrading the firmware from D-Link's website but it says "The version of setting file is not compatible." for the .bin file.
View 5 Replies
View Related
Nov 1, 2010
I have a client with an AP541n, most recent firmware installed. When he logs into the management interface (via IP using Google Chrome browser), it will work for a few minutes and then just disappear. If he attempts to reload the page he gets a message similar to a website being down (page cannot be displayed). The idle timeout has been extended to 4 hours, but this can happen at any point while logged into the interface.
View 1 Replies
View Related
Jan 18, 2011
Every few minutes my WGR614v6 loses connection to the cable modem though the wireless in-house is strong. Cable modem being reset does not work. Resetting netgear router brings us back online but only for a few minutes. Have replaced power supply to router and it is still occurring.We have a desktop and 2 laptops online. Also, the notebooks always drop to 18mbps while the desktop stays at 54mbps.
View 2 Replies
View Related
Feb 12, 2011
My LG BD570 is losing connection about 30mins in while I'm streaming an .avi from my desktop.This problem has only been happening since I setup my new wireless router. Belkin N300.I have no other network problems between my computers or simply using the internet.I did not have this problem previously when I was using an older Belkin Wireless G+ Router.
View 4 Replies
View Related
Aug 9, 2011
I bought a Linksys router last summer for my PC and Xbox. The PC and XBox are hardwired into the router. About two weeks ago, my router began dropping connection throughout the day. Sometimes it happens 3+ times in an hour. Other times it works for several hours before it drops.I upgraded the firmware as one fix and did a hard reset of the router. Still drops connection.I changed the MTU to 1400 and it worked fine for several hours but then dropped again the next morning. Also, like others on the forums, when I changed the MTU and hit Save Changes, it just ran and ran, never timed out...but never showed that it finished the command to save (if you get my meaning).I downloaded the Cisco Wireless Magic program to troubleshoot. It tells the same thing everytime. Unplug your router for 10 seconds and start over...My PC sometimes flashes a warning when I am restarting the router that I am getting Limited or NO Connectivity.
View 7 Replies
View Related
Oct 25, 2011
I bought a DIR-655 about 8 months ago. I had no problems connecting to the internet for the first couple of months. Then I would get a random connection problem where I would reset my modem or the router and all would be fine for a while. Then about a month and a half ago it started getting worse and worse and about 3 weeks ago it got to a point that I was resetting the router or modem daily to get a initial connection to the internet. And that would last until the next day when we would try to access the internet. Ocassionally, if I had a good initial connection, I would get a random loss of the connections a minute or two after I started surfing the web. Initially a modem or router reset would clear this up too. This happening both over wireless and through the hard wired connection. So it doesn't matter how I am using the Router. AND, most recently resets may not even get me a solid connection to the internet. So, I have bypassed the router for now.
The router was set up with changes to only passwords, network name, a changed router IP address and not broadcasting the wireless it has worked fine. After the reset, I left the router IP address as the default but changed the above security settings. Nothing else was changed. I have never had any issues logging into the router menus through the default or my defined IP addresses.
In doing some troubleshooting, I performed a reset on the modem several times, none of which resolved the problem, I was still losing the connection. Then I bypassed the router and did a direct connection to the modem and all is good and I have not had a connection issue since. I even tried changing the Ethernet connection on the back of the home computer to a different computer port but that changed nothing. I am currently trying a different cable. I am using the standard connection scheme:Cable from outside to modem, modem to router via Ethernet into the proper router port, Router to static computer via Ethernet. And a laptop accesses through the wireless. All cables have been working fine and are home built CAT 5e cables
It is really frustrating and I am not sure where to start now. Currently, I am running without the router for internet but I need it for the wireless to a laptop in another room. I use Time Warner Cable and have a Atlantic Scientific DPC2100 cable modem.
View 5 Replies
View Related
Jul 13, 2012
My wireless users are loosing the internet(http and https) connection many times per day. I just check the ports configuration in the switch, but The problem persist. The device is a Cisco Aironet 1130 AG.
View 4 Replies
View Related
Jul 12, 2011
I have to reboot my router a couple of times per day because I lose WAN access. This occurs with both the wireless and ethernet connections. Basically, I see that I'm connected to the router, but have a self-assigned IP. Power cycling the router does the trick. I never had this problem before, so I'm wondering what's up. The firmware has long been up to date. Router version is 8.0.
View 2 Replies
View Related
Oct 3, 2011
So i have this old WRT54GX v2. It have been running fine for the last ~5years. But since this morning i'm losing my wired connection after about 10 sec og connectivity, can't even ping it when it drops. If i turn it off for 10 sec the same problem occurs. Tried both static ip and dhcp. Wireless doesn't work either.
View 5 Replies
View Related
Jul 5, 2012
I have an E4200 v1 wireless router. Intermittently, my hard wired laptop (and hard wired desktop) loose Internet connnectivity and when I look at the 4200 I see the status light flashing slowly like it was just rebooted. I am runnong 1.0.04, have reset to factory, reflashed the 1.0.04 code and done a 30-30-30 reset (so far no drops since the 30-30-30 reset but we'll see).
View 9 Replies
View Related
Jul 8, 2012
I have a WRT400N that loses connections for my PC and other devices in my house (IPHONE, IPAD etc.).Sometimes it fixes itself other times I need to to a hard reset to boot the router and then evryone can signin again
The Firmware Version: 1.0.01 B19
The operating system on my PC is WIndows 7
View 9 Replies
View Related
