Cisco Wireless :: 5500 - Limiting Access To The Boardroom Access Point

Jun 4, 2013

I have a 5500 controller that we use to manage our lightweight access-points. We have had complaints that the 'guest' vlan in the boardroom is not usable. Our guest vlan is in fact overloaded.
 
I went back to the original site survey and noticed that coverage for the room is not ideal so I would like to have a new lightweight access-point installed in the boardroom and somehow limit the access to it to only a few people.

View 11 Replies


ADVERTISEMENT

Cisco Wireless :: 5500 - Image Loading On Access Point?

May 20, 2012

I have a new WLC 5500 series which i upgraded to a newer version. We got brand new AP's 1242 from Cisco. My ex-colleague had said that we can pre-image the AP's using the controller, so the new AP's get the image directly from the Controllers.
 
I have the following devices with me for this: A WLC 5500, 1242 AP ( 12 No.'s)  and a 2960 switch.  I tried to create dhcp pool in wlc so the ap get the ip and gets the image . However, i cant see the ap appearing in wireless tab.
The WLC & AP will be connected to this same switch.
 
What configuration needs to be done on the WLC & the Switch so that the 1242 AP's when connected physically to the ports on the switch will get the image from the WLC.

View 7 Replies View Related

Cisco Wireless :: 3602e Access Point To Work With 5500 Controller With Code 7.0

Jun 15, 2012

i have cisco CAP 3602e series access point to work with 5500 series controller with code 7.0i did not find VCI option 60 for this type of APs to configure DHCP. How I can let these APs will join the controller, i mean through which process DNS discovery methode and what about if i need to configure option 60 and 43 in dhcp for ap joining process to controllers.

View 4 Replies View Related

Cisco Wireless :: 2500 / 5500 - Wireless Access Point Identification By Clients

Apr 30, 2012

We have recently been given this unusual task.  The setup is a series of CAP3502P access points, and a wireless controller (either 2500 Series or 5500 Series), as well as other standard network infrastructure.
 
In this network, the client (mobile/wireless) devices must be able to detect when they change what access point they are communicating through, while also requiring a seamless transition.  Ie, if the client device is communicating via access point A, and displaying the application menus for A, when the user walks to the area services by access point B, it must detect that sot he application can display menus for B, without the user having to select "B".
 
Is there a way for the client device to detect which access point it is using and provide that to an application? Or alternatively a way for a host service residing on a server to get that information from the wireless controller?

View 2 Replies View Related

Cisco Wireless :: Upgrading 1042 Access Point To Lightweight Access Point

Apr 20, 2012

I had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.

View 4 Replies View Related

Linksys Access Point :: Connect And Configure WAP54G Access Point To New Cable Modem?

Nov 1, 2012

How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.

View 1 Replies View Related

Linksys Access Point :: WRT54G - Unable To Find Access Point In Home Network

Aug 29, 2009

I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1.  My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
 
I found directions in the forum for a setup using the LG BD390  but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold  from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
 
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi. 

View 3 Replies View Related

Cisco Wireless :: 3502p - Access Point Support MESH And Point-to-Point Bridging?

Apr 16, 2013

I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?

View 6 Replies View Related

Linksys Access Point :: WAP54G Access Point Setup After A Reset?

Jul 9, 2006

I had to reset my access point but the login screen fails to appear to lock the router.  I don't have the setup wizard disk.

View 9 Replies View Related

Linksys Access Point :: WAP54G Possible To Downgrade Firmware From Access Point

Jan 17, 2013

I have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?

View 1 Replies View Related

Linksys Access Point :: WRT320N Access Point Vs Range Extender

Dec 14, 2011

Have a WRT320N router at one end of the house in the basement.  Would like to boost signal to other end of the house.  Which product should i use, an access point or a range extender?  My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.

View 1 Replies View Related

Linksys Access Point :: WAP4410n MIBs Or OIDs For Access Point

Jul 3, 2012

I have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?

View 1 Replies View Related

Linksys Access Point :: WAP54G Access Point Unable To Connect To More Than One PC?

Apr 25, 2011

I've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
 
 The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
 
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
 
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.

View 3 Replies View Related

Cisco Wireless :: Point To Point Access Point 1262 Bridging

Feb 27, 2013

How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.

View 12 Replies View Related

Cisco Wireless :: 2960 - Autonomous Access Point / Get Guest To Access Internet?

May 9, 2012

I have two SSIDs on an Autonomous Access Point, that goes to a 2960 switch, that connects to a L3 3560. I have a vlan for admin/private internal access that uses the native vlan (1) and guest vlan (50). I have configured both and I am trying to get both to go out the same Internet connection.

I cannot get the guest access to access the Internet. It looks like my computer will go, but it just comes up saying no Internet access.All interfaces are trunking this vlan properly. I can communicate from the laptop to the 3560 but I just can't get to the Internet.          

View 10 Replies View Related

Linksys Access Point :: Cannot Access Configuration Page For WAP11 Access

Jun 12, 2007

Cannot access configuration page for WAP11 Access

View 9 Replies View Related

Linksys Access Point :: Repeat WAP54G Access Point?

Aug 25, 2011

What I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G. 

View 4 Replies View Related

Linksys Access Point :: WRT120N - Cannot Connect To An Access Point

May 10, 2013

I'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
 
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.

View 1 Replies View Related

Linksys Access Point :: Configure WRT120n As An Access Point?

May 1, 2012

Is it possible to configure WRT120n as an access point?

View 1 Replies View Related

Linksys Access Point :: E3000 Configuration As Access Point?

Apr 6, 2011

I have 3 E3000 Routers and would quality input regarding using 1 of the E3000 Routers connected to my Broadband Modem (Roadrunner) and would like to know how to configure the remaining 2 E3000 Routers to be hardwired to my main Router as Access Points located approximate segmented 1/3rd areas throughout my house which really is only 1800 Sq.Ft. in area. How to be configure these routers as access points as well as configuring the main router that will be connected to my broadband router. This is my first network to utilize streaming video, Internet Television Programs, Internet Radio, Accessing the Internet in all rooms of my house and outside the immediate adjacent patio area.

View 1 Replies View Related

Linksys Access Point :: Way To Find Mib For WAP54G Access Point?

Feb 10, 2012

I have tried to find mib for my Linksys WAP54G acces point  without succeed. Any body know how I could find it?? I want to program a software based on SNMP protocol. Is there some databses for mibs?

View 1 Replies View Related

Cisco Routers :: Limiting Web Access Using An RV110W

Feb 13, 2012

Is it possible to set up an RV110W to limit access to only specified websites according to a schedule? I can block access to specific sites using the Internet Access Policy settings under Firewall, but I can't figure out a successful way to block access to all sites except those specified.  I also tried establishing access rules but that did not work either.

View 4 Replies View Related

Cisco WAN :: Catalyst 3560G - Limiting VLan Access?

Jan 27, 2011

I have three VLANS set up on my Catalyst 3560G switch.  Each VLAN has its own subnet and I have enabled IP routing and set up my VLANS so that clients on VLANS 1 and 3 can get to VLAN 2 because they share a server located on VLAN 2.  However, now they can also see and get to each others VLANS! How I can allow my clients on VLANS 1 and 3 access a server on VLAN 2 but not access the other VLANS?  I don't want VLAN 1 to get to VLAN 3 or VLAN 3 to get to VLAN 1. 

View 17 Replies View Related

Cisco Wireless :: 5500 Cannot Access AP / How To Reset

Jan 30, 2013

I have a Cisco aironet 3502i access point which I am using with a 5500 Wireless Controller. I was configuring the AP for flexconnect and accidentally enabled PPPoE authentication - but never set configured login details for PPPoE. Now when the AP boots up it tries to use PPPoE but fails - it never even looks for an IP address. I have no way to get the AP connected to the controller again.I tried logging into the AP via console, the AP gives me output but I never get a login, even when I hold down the Mode button during startup.I also tried holding the Mode button and waiting for the AP to boot with its default IP (10.0.0.1) and connecting to the AP via telnet, but I was unable to connect or even ping with my PC on the same network configured as 10.0.0.2.What can I do to set this AP back to defaults, to become a normal DHCP client, and reconnect to the wireless controller where I can reconfigure it?

View 9 Replies View Related

Use A Netgear Wireless Card To Access Belkin Wireless Access Point?

Dec 23, 2012

have netgear pcmcia card need to connect to new belkin wireless access point.

View 1 Replies View Related

Cisco Routers :: RV042 - Limiting HTTP Access By IP Address?

Feb 22, 2013

I am trying to limit HTTP access to my server on the local network to a specific IP address.  I create an Access Rule in the firewall section, however that doesn't work.  The only way it works is if I add the internal IP address of the server to the Forwarding section where I create a new HTTP forwarding rule.However, that is not good because that allows ALL HTTP traffic to that server instead of just by the single IP address.

View 2 Replies View Related

Cisco Wireless :: WLC 5500 Guest Access Logging

Aug 8, 2012

In the ISE documentation is states that under a Guest_Activity report you must have guest access logging enabled on the NAD in the ISE network. My question is where do I enable  guest access logging in the WLC that is our NAD?

View 1 Replies View Related

Cisco Wireless :: WLC 5500 7.4 HTTPS Access On Service Ports Using HA AP SSO

Mar 5, 2013

I use the Service port connected to the managementVLAN to manage the WLCs. When configuring HA with AP SSO, I lost HTTPS connectivity to the WLC, telnet still works fine.I researched the deployment guide and it states:
 
- When AP SSO is enabled, there is no SNMP/GUI access on the service port for both the WLCs in the HA setup.Why is remote access disabled using GUI when using HA, and how can I keep management of my WLC using HTTPS and an address in the ManagementVLAN.

View 10 Replies View Related

Cisco Switches :: SG-200 Access Point Is Only Able To Access Internet / When It Is Plugged Into Port

Jun 22, 2012

I'm having some difficulties with the VLAN setup on the SG-200 and the WiFi access point. The access point (a TP-Link WA801N) is only able to access the internet when it is plugged into a port that is on the default VLAN (PVID 1). If I plug it into one of the other VLANs then any clients connected to the WiFi lose access to the internet and cannot access devices on the VLAN. I have previously used this setup with a first generation Cisco WAP4410N. [code]

View 4 Replies View Related

Cisco Wireless :: 5500 WLAN / AIR-LAP1142N - Joining Access Points

Nov 1, 2012

Got a bit of a quandary with joining new access points to our 5500 series W LAN Controller. It looks like the LAP is initially able to see the W LAN controller, but after that things go sideways. The LAP is pulling a valid IP address from DHCP, and the W LAN Controller is able to ping it.
 
In the controller's AP Join Statistics we get this: 
Last AP Message Decryption Failure  
Last AP Connection Failure   -Timed out while waiting for ECHO repsonse from the AP
Last AP Disconnect Reason  
[code]...

View 7 Replies View Related

Belkin Routers :: N600 - Unable To Access Dashboard In Access Point Mode?

Mar 6, 2013

Setup N600 DB as an access point using the most recent firmware,3.03.12? Once I do I'm not able to access the dashboard even through I enabled the remote management option.

View 2 Replies View Related

Connecting Tp-link Wa901nd Access Point As Repeater Without Access To Router

Oct 21, 2012

I have just moved into a new apartment that has a free wifi connection the problem is that my apartment is in the basement at the completly opposite side of the office and i cant get a strong enough signal to connect to the internet and im not very good with computers. the first time i tride setting up the repeater i was able to connect everything and get online but it had changed the ssid and when i tride to change it bacck to its origanil name i lost my internet connection and have not been able to get access the internet again.

Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows XP Professional, Service Pack 3, 32 bit
Processor: AMD Duron(tm) processor, x86 Family 6 Model 8 Stepping 1
Processor Count: 1
RAM: 479 Mb
Graphics Card: S3 Graphics ProSavageDDR (Microsoft Corporation), 32 Mb
Hard Drives: C: Total - 24385 MB, Free - 3678 MB; D: Total - 13776 MB, Free - 13649 MB;
Motherboard: , KM266-8235
Antivirus: None

View 3 Replies View Related

Linksys Access Point :: Cannot Change Channel On WAP45 - Unidentified / No Access?

Jul 5, 2012

How do I change the channel on my WAP45. I can't connect I get a message unidentied-no access

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved