I working with guest accounts on a WLC 5508.if there is possibilty to print out the account information directly from the controller. If possible how to print out this accounts ?
View 3 RepliesWe currently have ACS 5.4 and Cisco WLC 5508's deployed. We have wireless lobby admin accounts that can login and successfully create and modify guest wireless accounts. What we are trying to do, however, is give the lobby admins the ability to create wireless accounts with lifetimes longer than 30 days. Currently our setup will only allow the creation of permanent accounts (by entering all 0's in the lifetime fields) or accounts that last up to thirty days.
View 4 Replies View RelatedI have two 5508 WLCs. Both have APs attached to them. If I create a guest account with the lobby administrator on one, will that user account be able to log in to the network if the client is attached to the ohter WLC? So far, I have found that I need to create the same user on both WLC's, in order to have the user login.
View 2 Replies View RelatedMy customer has multiple sites, each with a 2504 WLC.A data center with a 5508 in the DMZ acting as Anchor for the remote sites.ACS 5.x and NCS Prime.All guest users will egress to the internet via a Vlan in the DMZ.Authentication is currently web-auth on the Anchor, but will move to NCS once that is fully deployed.
Is it possible to put a printer in each site for Guest WLAN users to use?
We have a wireless router on our network 192.168.23.xxx and if the main router SSID is enabled we can connect to the internet, but am also connected to the network. I want to allow guests to use the wireless but not be able to see our network, I disabled the SSID broadcast and setup the Guest account and enabled the guest SSID broadcast. The note in the configuration says that guest will have to open a web browser and enter the password to use the internet. When connecting to the guest account nothing happens. I never see a login screen, nothing. I typed 192.168.1.1 into the address bar and it did oopen a login page for the guest account but does not connect to the internet. The network viewer says it is connected but the webpage says limited or no connectivity.
View 1 Replies View RelatedI have followed the details here as closely as I can:URL
I've upgraded to 7.4. I've enabled IGMP snooping, increased the time out, decreased the query/hello interval, went into Controller> menu and set AP Multicast Mode to Multicast with the Bonjour multicast range of 224.0.0.251.
Went into my WLAN and enabled Multicast VLAN Feature, and enabled my Multicast Interface as the same VLAN as the WLAN range.
The Lantronix Bonjour device is on the same VLAN as the WLAN (13). Accessing the Lantronix device shows it polling printers on our wired VLAN. However, no iDevice that joins the WLAN/SSID can find these printers.
why datacard isn't connecting of my laptop in guest account?
View 1 Replies View RelatedI can connect to the guest account but it cannot resolve DNS addresses; how should the router be set up?
The regular (non-guest) account works as advertised. The E1200 is connected to my Verizon modem/router. I have tried disable/enable of DHCP on the E1200; I have tried setting the E1200 Static DNS 1 to my Verizon router IP address without success.
To enable our receptionits to print a guest user ticket on a small A8 ticket printer I'm looking for a way to adjust the layout and formatting of the guest account credentials page.
I have searched through the javascript and css files but with no success.
We are using WCS 7.0.172.0
I have an E2000 setup with the Cisco Connect Utility. I have a MAIN account and a GUEST account setup.I'm recently having a problem where I can only connect wireless through the "Guest" account. I can connect to my MAIN account, but it states that I have "Limited Access".
View 9 Replies View RelatedI haven't found a way to rename the Guest account on my E3000 router. If my router is named HomeRouter the Guest account automatically gets the name HomeRouter-guest. I have disabled the router's SSID broadcast, but it still broadcasts the almost identical Guest account.
View 4 Replies View RelatedI have setup my EA3500 for guest access however when my clients connect and start their browser they are never prompted for a password to continue their session. The browser times out. I can connect to the secured network by using the wireless password and the clients work.
I have the lastest firmware. I have a host of different clients, Kindle Fire HD, RIM Playbook, Windows 7 laptop. I have turned off guest account restarted, reconfigured and nothing changes. The browser always times out and the client is never prompted for a password. I bought this router because a friend that I visit has one so that visitors can use the internet...I know hers works, I have brought my Kindle along with me and connected to her Linksys router and it prompts for a password. I liked the feature so much I bought this one.
FYI. This router was replaced under warranty, I spent two days (I'm not kidding) on the phone with Linksys support trying to get the first one to work. I rebooted, reset to default, changed settings, tweaked, used different clients all with no effect so they replaced it.
I would like for Cisco to offer a firmware update for my 4200 so that the password for the guest account can be disabled.
View 1 Replies View RelatedWhen I turn on computer I can only work my internet on guest account will not work on the other account how can i fix this problem?
View 3 Replies View Relatedhow to set WLC 5508 to allow single create web authentication user account to get connected in a same time. i found that i can use the same username and password combo to be login in 2 machine in the same time.
View 4 Replies View Relatedhow can i delete a belkin wireless router guest account that was configures automatically upon setup?
View 1 Replies View RelatedMy friend was able to access my internet connection via my guest account WITHOUT having to enter the guest password. He was able to connect using a samsung galaxy phone with the android OS. However, when I connected to my guest account using my blackberry, I WAS asked for the guest account password.
View 3 Replies View RelatedI cannot sponsor a guest account using his/her email address. When I try to create a guest account, its show as file attached.
For example,
email.m@email-me.co.xx ->>>>>> cannot create
email.me@email-me.co.xx ->>>>>> can create
ISE version 1.1.1.268
Patch version 1
When setting up our router for Wifi, we made an account which is locked, but accidentally made one for guests which is not locked. How can we eliminate the guest account?
View 3 Replies View RelatedI want to prevent guest from doing peer - peer communication on my Guest (5508) controllers. Is this a feature on the WLC or only by applying an ACL on the router interface?
View 2 Replies View RelatedIs it possible to provide wireless guest access over the WAN from another office via the WLC. I have WLC 5508 in a central office and have other remote offices that have one Access Point in each office that are autonomous; I will be converting these to LWAPP. Is it possible to route guest traffic back to the WLC then forward this traffic out to the internet? How would I route this traffic out as well? install a secondary WLC in the DMZ and use anchor points. I only have one WLC
View 7 Replies View Related, I have a requirement by a customer that they will want to monitor the guest wireless access. Currently, we are proposing a Cisco Wireless Controller 5508 together with APs and the setup would be a dedicated VLAN for guest. I am wondering if Cisco ISE together with Cisco MSE would be sufficient?
Stuff to monitor and log are:
1. Guest username (I guess this would be self sponsored)
2. Company name
3. Websites accessed
4. Time, date and duration.
5. Logs are to be kept for 3 months at least.
I'm looking to implement guest WiFi access with web authentication on one of our 5508 WLC (currently deployed within a sandbox environment), but looking for some assistance. The WLC currently has a single connection from port 1 to the 'Test Site 2' switch. This is a dot1q trunk. On the WLC, the interface (for port 1) is configured as follows: [code] Currently, I have one WLAN configured with the profile name 'Guest Test 1', it's enabled and broadcasting the SSID. Security is L3 only with web authentication configured. The WLAN is configured to use the interface names "guest_wifi".
The issue is that when a client connects to the WLAN, it receives an IP address okay (10.99.254.x address), but doesn't seem to be able to contact the WLC to get the web authentication page. Eventually, the WLC terminates the connection due to an authentication failure.does it sound like I'm taking the correct approach here? The idea is that clients connect to the guest WLAN, which puts them on VLAN 99 and routes traffic through to the ASA and then onto the internet.
Where do you turn this option off? i have looked under security and did not see any thing.
View 1 Replies View RelatedI just got a new requirement for our wireless roll out and I need some help. Plan the best way to provide employee and guests wireless access w/ the guests separate from the production environment.
We have a 5508 controller w/ 1142 APs. I have two GBICs in the interfaces (only one is being used). I want to use a back haul connection for the guest access. I am having a hard time in visioning how to physically set up the cabling from the patch panel. Again, the requirement is to not allow guest users to connect to our production network but I still want/need to manage the AP. This will eventually need to be supported for remote sites tunneling back to the primary location.
I am running a 5508 WLC with 10 Access Point. we need to allow Internet Access to Guest. 10MB DSL Internet is dedicated for Guest. This link is terminated on a regular ADSL modem without being part of our network. We want all Guest Internet traffic to reach the ADSL Router. where should I create the Guest VLAN / where the DHCP for Guest users should be created. what is the best practise for similar setup.
Our Network is simple
ISP_Reuter-------ASA_Firewall--------------4505------------LAN-switch 2950
ADSL_modem------------ users connect via wireless but restricted to certain area only.
Could I setup wired guest Internet connection without layer 3 web authentication and how?I want guest users access Internet without going through web authentication.
View 2 Replies View RelatedWe have Cisco WLC 5508 in our network and right now ,this WLC is connected to two ports of each core switches.Both CORP and GUEST SSID are configured on this WLC. Now we want to segregate the traffic log GUEST to on core switches from WLC. SO my question is ,how can we achieve this without using guest anchor controller ? Can i use one interface Cisco WLC 5508 and connect it to the firewall or any device ?
View 17 Replies View Relatedi see there is an option to "allow password change" or "force password change" for guest roles in the NGS. But when i created a guest account using this guest role, after webauthentication , there is no prompt to change password. Is this the intended behaviour or is there anything else that i need to configure. Looking at it, i am not sure how the NGS would allow a "guest user" to really overwrite the password by allowing password change. ? is that not a security risk as well for the NGS ? my setup has 5508 anchor controller and NGS communicating via RADIUS.
View 7 Replies View RelatedGuestconnect SSID configured on 5508 WLC with Pass through athentication (NAC guest server). No issue with Laptops and Iphone/Ipad ver 4and 5. Only Iphone Ver 6 users unable to access Guest connect .
View 9 Replies View RelatedIn my Wireless network, I have two appliances WLC 5508 running version 7.0.116.0.I have a WCS running version 7.0.172.0, deployed on a windows 2003 server.I've imported the two WLCs in my WCS in order to centralize the monitoring and the configuration tasks.Now I'm facing an issue when I want to create a guest user from the WCS, rather than creating this user access on each WLC. The creation of the user account is working good, the replication is done on the both WLCs, but on one of my WLC the guest user account is deleted after one hour(around).On the second WLC, the same user account remains during all its life time.In attachment a screen shot of the advanced parameter of the guest user.You can see that the user was created on the both WLC but is only active on one ... and unfortunately the wrong because the AP is associated with the other WLC.
View 2 Replies View RelatedI've got a WLC5508 (7.0.116.0) that is managed by WCS (7.0.172.0). I set up another WLC5508 with the same code and managed by the same WCS. Now I'd like to export all the 800 guest user accounts with the passwords from the old WLC and import them into the new WLC.
View 10 Replies View RelatedI know that the recommendation from Cisco for the mobility anchor feature to work well is to use the same IOS version on the anchor WLC and local WLC controller. Now I´ll install on a new site a 5508 local WLC with a newer IOS version which is installed on the other controllers ( Guest and local ). Later I´ve planned to update also the other controllers to the same IOS version. Now my question is, must I upgrade all other controller at the same time ?
View 4 Replies View Related