I am trying now to deploy the setup that works on some APs and doesn't work on others.
For example, on an AIR-AP1231G-A-K9, the following setup works:
!
version 12.3
no service pad
service timestamps debug datetime msec
[Code].....
we have an heterogeneous network with Cisco devices (6509-E, 3750G and 3560) and Alcatel 6850 devices. We have to enable a PTP Wifi line as a backup for the fiber line between two buildings. For this purpose, we have connected a wifi device to GigabitEthernet 0/47 of SWIHGJ1 and configured it as: [code]
View 2 Replies View RelatedWe have 2 Cisco 5508 WLCs, each wtih 50 licenses. What I would like to do is split the 50 odd APs between the 2 controllers load balancing the traffic. If a controller goes down or there is a break in the path all APs would failover to their configured secondary controller. So far so good.
However there seems to be no way to 'replicate' the configurations between controllers unless I setup HA , but as I understand it HA is Active /Passive, so essentially, unless you get a failover situaltion, completely 'redundant'.
Is there a way or either replicating between controllers automatically with out HA, or is there a way of making HA Active / Active?
I have an AIR-AP1131AG-E-K9 running as root AP with three SSID's (mbssid), all WPA-2 PSK, IOS 12.4(25d)JA Now I would like to use an AIR-AP1231G-E-K9 as repeater for one of the SSID's (all three are AFAIK not possible), IOS 12.3.8-JEE(ED) So only one SSID is used.
I use exactly the same shared secrets and security settings on both devices, on the repeater the SSID is designated as infrastructure-ssid.Unfortunately I have the problem that the repeater AP cannot associate with the root AP.I have verified that aironet extensions are enabled, same security settings are used and checked many sites on the net which describe how to configure a repeater AP. Is there any incompatibility between these two APs? I have two of the AIR-AP1231-G-E-K9 APs available, do I need to use the same models?
Version 12.3 I currently have an open authenication customer network, I would like to add a second securt ssid for my sales department, is this possible, how do I do this, the more specific the better .
View 1 Replies View RelatedDoes WLC 2504 works with AIR-AP1231G-E-K9 and with AIR-BR1310G-E-K9 after I upgraded form AP to LAP the AP ?
View 4 Replies View RelatedI am trying to add an AP (1231G) with autonomous code (Version 12.3(8)JEC2) to WCS (v7.0.172.0). I recieved the following error:
Failed to add device to WCS Reason: Unified AP with same MacAddress already exists in WCS. Remove Unified AP first.
Does the Cisco vWLC support the cisco AIR-AP1231G-A-K9 platform?
View 4 Replies View RelatedBelow is he output from debug radius authentication from my AP.
I can see request is forwarding from AP to radius but Radius is not sending any response.Not sure why its not responding.
I also did not under stand few out outputs also
no sg in radius-timers and
RADIUS/DECODE: parse response no app start; FAIL
what does it mean.
I restarted radius server , changed secret key but no luck.
019639: May 1 16:15:08.727: RADIUS: User-Name [1] 32 "host/3KYGRH1.idcap.intdata.com"
019640: May 1 16:15:08.727: RADIUS: Framed-MTU [12] 6 1400
019641: May 1 16:15:08.727: RADIUS: Called-Station-Id [30] 16 "0012.01d6.f691"
[Code]...
I'm having the following issue with a couple of 1231's.
Some overall config info first:
This is a small office with 2x Catalyst 2950 (24-port, no PoE) switches and 4 AP1231G (autonomous). The APs get PoE from a PWRINJ3 each. The injectors are powered by the AP power supplies. Injectors and power supplies are mounted in the patch closet.
The 2 switches are connected together over 4 ports (20-23 on each switch), these ports are set to 1Q Trunk mode.
The APs are connected to the switches, 2 to each switch, on port 1-2. These ports again are configured as 1Q Trunk.
APs are connected to the switch as follows:
[switch] <- patch cable-> [injector] <- patch cable -> [patch panel] <- static cabling -> [outlet] <- patch cable -> [AP]
All this has been working without problems for a number of years.
A few weeks back, AP2 did not restart after a power cut (everything else did). All LEDs are off, port on switch has no LEDs lit. I did not get around to investigating this furtehr until last week. I unmounted (failed) AP2, took it to the spot where (working) AP3 hangs, and plugged it to the cable of AP3. AP2 came to life immediately. I unplugged it and plugged AP3 back in, which restarted immediately.
So I suspect a power supply issue on AP2. I took the injector and power supply that fed AP2 out of the patch closet. When connecting AP2 directly to the power supply, it came to life immediately. So I figure the injector is defective.
On the same day, I notice AP4 is also dead (again all LEDs off, no idea how long, could have been that day or could have been a few days - it has definitely been working after the power cut that appeared to have killed AP2).
So I order 2 new PWRINJ3s and for good measure 2 new power supplies. Later that day, I took the injector and power supply that fed AP4 out of the patch closet. When I try this combination (AP4, injector4 and P/S4), and connect it to a different wall outlet (and therefore a different port -16 - on the switch) IT WORKS! Should have triggered questions, but did not immediately.
Last Thursday I got the new injectors and power supplies. So I take one of each, hook them upto AP2 at my desk, and AP2 starts up. So I mount new injector2 and new P/S2 in the patch closet, put AP2 back in its place, connect all the cables - NOTHING. AP2 does not start. The "power" LED on the injecvtor lights up green, the "device status" LED remains off. I take AP2, new injector2 and new P/S2 to my desk, hook them upto a wall outlet (connected to switch port 17). AP2 starts immediately.
Meanwhile AP3 has (also) stopped working (no LEDs on at all). As far as I can tell, it stopped working after I briefly disconnected (and reconnected) the patch cable between injector3 and the patch panel in the patch closet. The LEDs on switch port 1 are off.
I have since tried to power cycle both switches (took power off both, waited a while, poewerd both back on). No change.
PS: the APs ran firmware 12.3(8)-JA until recently. AP1, AP3 and AP4 were upgraded to 12.3(8)-JEE after the the power cut that took AP2 out. THis is when I found out AP2 was dead. AP2 was still on 12.3(8)-JA. It was upgraded to 12.3(8)-JEE last week when it was on direct power on my desk.
I can't find any information that the AP1231G-A-K9 AP is supported in a 5508 Controller Based environment with Prime NCS.Could one of the experts confirm or deny?
View 1 Replies View Relatediam currently trying to replace AP1231G-E-K9 with new equipment / Cisco AP next generation maybe?The problem is that the system, that is going to use the AP is using aironet 350 PCMCIA adapter with LEAP. If in fact we are going to use a new Cisco AP, will the new generation work with Aironet 350 Adapter and support LEAP?
View 2 Replies View RelatedWe have this access point AIR-AP1231G-A-K9 for mobile users. current version is c1200-k9w7-mx.123-7.JA4. Sometimes users are able to associate but not getting IP address from dhcp. It shows 0.0.0.0 for the particular client.
View 2 Replies View RelatedI have this firewall working as active/standby. Everything seemed to be ok, but we noticed that confirgurations are not being replicated by saving configuration either copy run start or write. The workaround here is write standby command. Below the configs and stats, plus the show version, which is the same in both equipments:
Header 1
failover
failover lan unit primary
[Code].....
I have AP AIR-AP1231G-E-K9 with iOS c1200-k9w7-tar.123-7.JA2 and I want to convert it to Lightweight Mode with iOS image c1200-rcvk9w8 tar.124-21a.JA2. First of all, is it possible? Because I tried to convert from tftp server command (archive download-sw /overwrite /reload tftp://ipaddress/image.tar) and I cannot see in the controller. (controller and aps are in the same network)
View 11 Replies View RelatedI discover an issue with my CISCO ASA 5550 because I'm looking at the vlans that I have configured and some vlans on the Stand by device had not an IP address configured, checking the configuration of the failover
View 2 Replies View RelatedI have two switches, a 2960 (sw01) and a 2948 (sw02). The sw01 is trunking via dot1q on Gi0/24 to sw02 on 2/48. Why are VLANs 2-4 not active on sw02?
sw01#sh int Gi0/24 trunk
Port Mode Encapsulation Status Native vlan
Gi0/24 auto 802.1q trunking 1
Port Vlans allowed on trunk
Gi0/24 1-4094
[code].....
We have 2 ASA 5510's running in a Active/Standby configuration. It appears that most of the changes we make on the active unit are replicated to the standby unit. However, there are 3 AnyConnect Client Profiles on the active unit and none of them show up on the standby, the standby has no AnyConnect Profiles. We also have 1 OnConnect script on the active unit and it does not appear on the standby unit either.
I was under the assumption that all config items on the active unit would replicate to the standby. Is this not correct? Do I need to do something extra to get everything replicated? Are there other items that do not replicate?
I have two dinasour APs that I need to fix. They are configured in bridge mode to bridge a few VLANs between two sites. Right now the management IP on BVI 3 interface doesn't work. Does it have to be on BVI1 for it to work? When I say "work" I mean I am able to ping it and use SNMP to monitor it.
View 1 Replies View Relatedloading a new bin file onto a Cisco wirless access point ,the access point i have found is only in rommon stage
Access point model is : ap1231g-e-k9.
I recently setup our small office network using the following setup:
Cablemodem <--> router <--> 1231AP(role root bridge with wireless clients) <-> 1231AP(role non-root bridge with wireless clients)Code on both APs: 12.3(8)JEE.Office network generally has less than 3 wireless clients connected at any one time to either AP. AP's are a mere 50' apart; clients are all less than 30' from either AP; they all show excellent signal and connected at 54mbps signaling rates.
All is/has been working very well & very stable with the exception of speed. We have business class service from RR, approx 25mbps dl, 2mbps ul. Any hardwired client to the router switch ports are able to download at speeds averaging 23mbps. Any wireless client connected to either AP is never able to exceed download speeds of 5mbps. With no other wireless clients connected except my one test client, I was not able to exceed 5mbps throughput from either AP that I connected to.
I can confirm that the ethernet connection between the router and root bridge is up at 100mbps-FD and not showing any errors: [code]
Are these very slow thoughput speeds normal of this hardware combination?I did much searching/googling and found claims that by eliminating TKIP it almost doubles the actual wireless speeds our clients can obtain.
We have a cisco site to site vpn for two locations with cisco 871W devices. The VPN works fine for everything such as remote desktop, intranet and other applications.We have a Microsoft windows server 2008 at one site running Domain and a member server at another side, but the problem is with the DFS which also runs between two sites which is not replicating the folders properly.I am being told that before deploying cisco routers the vpn was on Tplink routers and the DFS worked fine and folders replicated with a full mesh topology. On the other hand since i am a cisco technician and a bit new to Microsoft therefore i have also been told by Microsoft technician that it is happening because Domain is not replicating with a member server properly which i doubt as few users login to the domain via member server and even if i create a new domain user on a member server it shows in the domain controller with in no time.
View 3 Replies View RelatedIs there a way to set up Quick VPN on the RV120W without changing the internal subnet? I have just taken over responsibility for a network and I don't know all of the nooks and crannies yet, so I'd rather not change the internal sub net. I've tried setting up a user then changing the LAN settings afterward, but it automatically removed the VPN user when I did so.
View 1 Replies View RelatedI've just purchased a couple of SRP527W routers. I've been unable to even browse to the default 192.168.15.1 to start my configuration. My local network is 192.168.1.x. At risk of showing my stupidity, what am I doing wrong.
View 5 Replies View RelatedI recently purchase my first Cisco products for a network for our church. I have a RV180W router, WAP 121 Access Point and a SR2016T switch for our network, which is just pier-to-pier at this point. We have 5 computers connected with ether net through the switch and all see the Internet and work fine. The wireless connection through the router is working fine with our wireless devices (laptops and i Pads). Where I am having issues is with the AP. It is in different area away from the router being powered through POE instead of the regular power connection.
My problem is this: it takes FOREVER to connect to the AP and to the Internet, even when sitting directly under the AP with full signal. Once connected, it appears to allow Internet connection just fine, but getting to that point takes 15-20 minutes sometimes. Also, when I come back the next day, I have NO signal at all, as it seems the AP has "timed out" due to inactivity or something. I have to reboot the AP and the router to get it all back up and running again. I need for the signal to stay up all the time or at least come on when someone connects.
So, what am I doing wrong here? I have recognized and authorized the AP through the router config, security is set up fine and I can see it once it comes up. I have the AP set up as a completely different SSID, although I would prefer to have the AP as merely an extension of the router's wireless network if possible.
I got the task of setting up a Guest wireless network for one of our remote campuses. We already have some APs that are connecting to our WLC.
The Enviroment:WLC Cisco 5500 is at our Corporate office. Connects to our Core Switch then to our Router Router connects to our remote campuses over mpls.
We currently already have APs at this campus that are connecting back to our WLC.
We have a DSL line at the remote campus that we want this Guest wireless routed to.
I have already created the guest network on the WLC and a guest VLAN on the Core switch.
My main question is how to configure the two routers for this and have this go out the DSL modem?
I work for a school system and we are currently entertaining the idea of BYOD. We have a Cisco 4404 controller and what I would like to do in order to prepare for BYOD is to create a wireless network that can be connected to with AD credentials. So basically, on any device, when users try and connect to this specific WLAN they will be prompted to put in their AD username and password to get access, that’s it, no other passwords. I will be using the Network Policy Server role in Server 2008 R2 as my radius server. how to actually set up the policy within NPS for this type of authentication. Also, on the controller side, am I basically just setting up the WLAN and then setting up the authentication server on the AAA Servers tab for security? Leave Layer 2 and Layer 3 tabs blank if I only want to use AD credentials?
View 3 Replies View RelatedCurrently I have a wireless router shared with a cable modem and three PC's. Would I be able to add the mac to this set up or do I need some kind of mac enabled router?The three PC's all run W7 Home Premium?
View 2 Replies View RelatedMy wireless wont let me set it up i've got the cd and everythimg. when it tells me to insert the usb i insert it then it tell me to wait but nothing happens ive done it for a day with out disconnecting and nothing happened.
View 2 Replies View RelatedI have a Linksys EA4500 setup on my corporate network for wireless access. I have enabled the guest network and from all I can tell it's on a seperate subnet from my internal network like it should be. 192.168.x.x My internal is on a 10.x.x.x network. I conenct to the guest network using a laptop and I'm prompted for a password to get to the internet, which I like. The one issue I'm seeing is when I'm connected to the guest network I can still do an RDP session to internal resources. How is this possible if the guest network is on a seperate subnet?I take a laptop which has not been joined to my domain, connect to the guest ssid, and then open an RPD session and enter an IP address for an internal server and it connects. Is there a setting to keep this from happening
View 6 Replies View RelatedI finally decided to go with a e3200 yesterday and picked up one at Walmart. Last night I went to hook it up and had no luck setting it up. Now I have able Internet with a phone VoIP service. After trying to connect several ways, all the router wants to do is sit with a flashing power light. I cannot access the setup page wireless or wired and have tried several methods I found last night.
View 1 Replies View RelatedI am trying to setup to wireless routers onto one network. One router is the ES4500 the other is the Apple Time Capsule. The apartment I am in has thick walls and because of this, there are some wifi gaps. Trying to set the second router in a different room to act as a wireless bridge/access point for the first router.
View 2 Replies View Relatedi have a cisco rv110w vpn/firewall/wifi and am trying to get vpn up and runing so vp can login from home and do his work.
View 1 Replies View Related