Cisco Wireless :: Aironet 1040 Access Point Managing
May 22, 2012
We are currently using several AP's in our organization. And in this one AP i want to give a user the power to change the password of the wireless network to prevent miss use. I was wondering if it was possible to create an account who only has the privilege to change the WPA key?? I want to prevent that he will accidently change other settings.
I'm working on setting up an Aironet 1040 Wireless Access Point for my company. It's my first time setting up something like this, and I've run into a bit of trouble.
I created my first SSID easily enough, following the manual and guides online. I set up VLAN 1 as my native VLAN and linked it to my SSID with the encryption and security that I was told to use and it works great. However, my boss asked me to set up a second connection as well for guests at the office, and this is where my trouble starts.
I created VLAN 2, and then another SSID which I linked here. I set up encryption and security the same way, and I can see the network when I open up my network and sharing manager. I can connect to the network as well, but I either get a spinning blue icon where my signal strength indicator is or a few bars with a yellow caution sign, and Windows says 'Identifying...'. I've compared the two SSIDs using the console and the GUI and I can't seem to spot any obvious differences between them.
On my Accespoint i have 2 vlans: 1 for my wifi phones and 1 for my network.Wifi Lan has the SSID LAN with WPA enterprise authentication to a radius server(ms server 2008).Wifi Phone has SSID PHONE and vlan 50 with local radius authentication.This Works all fine, Except when i enable AP for my wifi phones. When AP is enabled the authentication for my lan doesn’t go to my server but local.How do I configure my accesspoints so that the cisco phones use the local radius server with AP and my windows computers connect using the ms radius server?
I have been racking my brain for a while and cannot figure out why I am not getting 144Mbps out of my Aironet 1040. I was reading a previous thread ([URL]) and set it up exactly like it said. I have set the encryption to Cipher AES CCMP and set the SSID to open authentication. I also set the SSID's key management to enable WPA (WPAv2).
I was reading that WMM has to be set. I have 3 options: Disabled, Legacy, and dot11d. If i chose dot11d I have to put in a coutry code. Problem is there are no options in the country code pull down. I cannot even manually type it in.
Another problem is that cell phones cannot connect. It keeps saying authentication fails in the log.
I am attempting to configure two Aironet 1040 series wireless access points for the first time and am having some difficulty. This office does not have a RADIUS server so I would like to set them up to use WPA2 with a pre-shared key. However just how this is accomplished is not immediately apparent. I have attempted using both the command line interface and the web interface, but I get errors in both places. It doesn't seem like it is all that difficult, we're just talking about a few lines in the configuration file.
This is what I have so far:
Current configuration : 1684 bytes ! version 12.4 no service pad
I am trying to create a welcome screen for people who join the guest network on my aironet 1040.Webpage pass-through is really what I want but I know that doesn't work on a 1040.What does: IP redirect, Conditional Web redirect or Splashpage redirect?
we have several AP1040 in the office, but the latter is a Dual Band 2.4 GHz and 5 GHz. And we have problems with all workstations MAC OS X gets a lot of disconnections during the day, the strangest thing is that the OS X community is aware of the problem, and their only recommendation is to buy the external Aironport has better hardware.
I am trying to find a way to login to our wirless access point. I have a Aironet 1130AG series wireless router. I have the ip address. It is a POE device so i dont have a power supply for this device. When it is on I can see the Wireless Network but the passcode has been lost and no one knows it. Is there a default IP address for this equipment? There is an Ethernet port for a console but without the power supply i cannot access it.
I am looking at outdoor access points, I want to stick with Cisco aironet, we currently have 6 of them that are 6 years old and running great, one has had a problem because of humidity, dried it out and relocated and we are good again.
I was looking at the Aironet 1310 Outdoor access point, but I can't find much information on it. I am looking to see how many SSIDs can be setup, we currently have 2 one private, and one public, this is done with VLANS. I am also looking at finding out about the power injector, it converts to coaxial cable, it has 2 RJ-45 and 2 Coaxial, does this mean if we get 2 access points, then I only need 1 power injector?
Every device I've tried to connect to my WiFi network have no issues connecting at all, except for, as far as I can tell, Samsung Android phones. My sample set is very small, but both a Samsung Galaxy S3 (both before and after custom ROM install) and a stock Samsung Galaxy Nexus.
I've tried setting a vlan up with no encryption and open authentication, and the phones just halt on "connecting". This issue is both on the 2.4Ghz and 5Ghz Radios.
What is working is various computers with both intel and broadcom adapters, a Brother printer, and a Motorola Droid 3 and Motorola Photon Q. I'm starting to think that it's an issue with the radio in the Samsung phones, but the S3 is 5ghz compatible and the Nexus is only 2.4, so they must have different radios. I'm also pretty sure that it's not software on the phones since the S3 had the same problem with stock ROM and CM 10, and the Nexus is Vanilla Google ROM.
I'm waiting to get a chance to upgrade to the new FW for my aironet 1040, and I'm going to fire up an old 1130AG as well as test with an iphone or ipod when I get the chance; I'd just really like to find out what the heck is going on with these samsung phones.
Current configuration : 13969 bytes ! ! Last configuration change at 10:18:26 MST Sun Dec 23 2012 ! NVRAM config last updated at 10:18:26 MST Sun Dec 23 2012
I want to connect two buildings. Let's call them Building A (main) and Building B.
„A“ is the main building and provides a wired LAN to an AAA server (192.168.1.2) and the WAN gateway (192.168.1.1). There I placed a 1262N with the IP 192.168.1.3 connected to the wired LAN and configured it as Root-Bridge. Let's call it AP01.
„B“ is a pretty large building and has a wired LAN from one end to the other end. So I placed two 1262N there, each at one end.
The first 1262N is configured as non-root Bridge (AP02) and connects to the Root Bridge (AP01). The IP address of AP02 is 192.168.1.4.
The second 1262N is configured as Access Point (AP03) and connects to the non-root Bridge (AP02) via the wired LAN. The IP adress of AP03 is 192.168.1.5
1. Do I need tell AP02 about the AAA Server in Building A or acts AP01 like a AAA Proxy for AP02 because of it Root Bridge functionality?
2. How Do I tell AP03 that it should use AP02 as a gateway to building A?
I have a very special application where I need to connect as much as possible end devices to a single access point.The required data throughput per end device is very small - around 1 to 5 kbit/sec.I am using the Access Point Aironet 1242AG.
1. What is the maximum number of simultaneous users that can be connected to a Cisco Access point, is it 255 or can be more ?
2. If I define multiple SSID’s, what if the total numbers of users that can be connected to a Cisco Access point
3. I there a simulator tool that can be used to simulate multiple wireless connections to an AP
4. Have anyone tested so many users connected to 1 Access point ?
I would like to buy Cisco Aironet 1260 Access Points, i just want to use them independantly so i want to know do they work without the Wireless LAN Controller? or i have to have the controller for them to work? they will be in different locations so i cant have a controller per each location.
I must configure an Aironet 2602e Access Point, as a standalone access point (without WLC), but I can not find Configuration Guides for that. I have only found the "getting started guide" but there is described an installation combined with a WLC, which I have not. Is it provided no real guidance from Cisco? I did something never done before.
We are in need to perform a site survey with the Aironet 1041N Access Point.
Upon reviewing the site survey software, it seems you need to use an Aironet adapter. However from what i can tell, all the Aironet adapters are PCMICA cards, which most modern laptops do not have, and the PCMICA cards that do exist don't have drivers for windows 7.
Are there USB adapters w/ Windows 7 drivers that can be used to perform a site survey?
We have 2 aironet 1310 aps setup as infrastructure access points between 2 buildings. One went south on us & we placed it. Before the bad one went down, we were able to manage both remotely & could see them from the next device via CDP. Now, we can't connect or even ping either AP. And the weird part is that the switches that connected to each can see each other via CDP, but not the access points between them. I'm attaching the configuration. Before I make the 2.5 hour drive back to the site, what I may have misconfigured on either or both access points?
I have recently purchase Aironet Access Point. I'm pretty new to Cisco systems and what i'm try to do is have the access point broadcast multiple SSIDs lets call them Guest and Admin. My problems is when i config router to have a DHCP address it works perfectly fine but when i assign a static IP it shows all the any connected device as unkown with IP 0.0.0.0. So i'm guessing i will need to setup a dhcp server. Is there a way access point can have its own DHCP server and IP address ( i don't want to use any from my STATIC ip subnet as i dont know alot of empty ones left) like home wifi router where they assign each device an IP like 192.168.0.1. Is this possible?
Is any one can configure basic Point-toPoint wireless bridge. I need to connect two simple LAN with Cisco Aironet1310 AP. I required basic configuration with basic authentication between these two devices which is on IOS "123-8.JEA3".
I have dozens of Cisco Aironet 1100 access points, each is managing its own wi-fi with DHCP. I had to disable dhcp on them because they are on a wired subnet where I am using the static IPs and don't want my wired clients to get DHCP addresses, nor someone to be able to plug the wire into own laptop and get on the network. It's been working fine with one exception - I need to be able to ping my access points from the central site, and I can't. What IOS command would enable ICMP echo on my access points in this case?
I have CISCO Aironet access point C1130 , but not able to connect by users, I can see below logs from access point.
Jun 13 17:50:10.686: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000 Jun 13 17:50:10.686: RADIUS: Retransmit to (220.127.116.11:1645,1646) for id 1645/247 Jun 13 17:50:15.678: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000 Jun 13 17:50:15.678: RADIUS: Retransmit to (18.104.22.168:1645,1646) for id 1645/247 [Code] .....
I am trying to change wpa2 key on an Aironet 1231g access point. Once I change they key, clients cannot authenticate to the access point unless they either change the password or forget and re add the network on the client device. Is there any way to make the client ask for a new key if the key doesn't match when authenticating?
i've been looking for a way to isolate clients on a Cisco Aironet 1121 on a certain SSID, and i cant find anything, tried pretty much everything i coudl remember, but since im no expert on Cisco wireless.
Cisco IOS Software, C1100 Software (C1100-K9W7-M), Version 12.3(7)JA1, RELEASE SOFTWARE (fc1) Technical Support: [URL] Copyright (c) 1986-2005 by Cisco Systems, Inc.