Cisco Wireless :: As 3500 Doesn't Work In Stand Alone Mode
May 2, 2012
We are deploying a new office and exploring the options for WLAN deployment. We were pretty impressed with 3500 series APs and that it supports CleanAir.However, we have decided to go for standalone AP deployment model now. As 3500 does not work in standalone mode, so we are looking for APs that can work in standalone mode ( and later can be converted to lightweight if needed). We can go for 1140 in that case. However, it would be better for us to know the main differences between features supported by 3500 lightweight AP and 1140 standalone AP. CleanAir looks like the main one. Are there other important ones as well?
View 2 Replies
ADVERTISEMENT
Sep 12, 2012
I have some old 1231 APs in the school in which I work.I would like to create a local network (no LAN, no internet, just a point to point wifi connection) managed by the access point (in DHCP).That's because we have an apple TV connected to a projector and some ipads. My idea was to put the devices locally in the same closed network for share via AIR Mirror the ipads on the apple TV.
View 3 Replies
View Related
Jan 10, 2012
I recently bought a Cisco E2500 for work, and after setting the router to Bridge Mode, I am unable to access the router web interface. I tried both the old IP address (192.168.1.1) and the IP address that I entered when I was configuring Bridge mode, but I couldn't get either to work. I have always tried resetting the switch to factory defaults and trying again to make sure I didn't type anything wrong, but to no avail. The wireless and everything works as it should, I just can't get back into the router to change any of my settings.
View 4 Replies
View Related
Aug 9, 2011
We have three brand new E4200 routers, all using the most current firmware (1.0.02). They are all in bridged mode, however when I attempt to enable the guest network on each of them, the config shows it as active, but it never shows up as visiible SSID. In previous posts, I've seen people saying that I need to do a complete hard reset of the router and re-enter all the configs again to get the guest network active. Is this true? I'd hate to think that I have to hard reset and reconfigure all three of these APs, just to get the guest network enabled.
View 2 Replies
View Related
May 7, 2011
hardware version D3, FW 4.10 and 4.11 same problem.
i tried with 4 wlan adapters: two of them support 802.11b/g, they always work find no matter which settings. the other two support 802.11b/g/n, as default "n" is enabled, so does DIR-615, both wlan adapters can be connected to DIR-615, they get their LAN-IP, but they can access neither DIR-615(no respone to ping) nor internet. but if i disable "n" mode either in the adapter or in DIR-615, everythin works fine, of course only with 54mbit max.
so what can i do to use the n mode?
View 1 Replies
View Related
May 22, 2012
Jason9 i'm having the exact same problem as above, don't mean to hijack but I'm using talktalk isp, I have AVG 9.0 and have a static IP and forwarded the required port on the router.
View 19 Replies
View Related
Jan 6, 2011
I have a DSL router Pirelli PDF A1000G.I have a Linksys e3000 and I have a dap-1522.When I bought a dap-1522 I thought it could do access point in fact i saw many videos in dlinktv before choosing an access point from DIY with mike etc to youtube there are 2 videos one showing bridged mode and another ap mode!Now what happens is this I have upgraded from firmware 1.11 that came as default to 1.21 i connect it wired to my linksys e3000 when it is connected with the ethernet cable wired I can connect to the internet and navigate and open sites and my ps3 can connect to it but my range is not very good only 40%!
Now I bring it downstairs remove the ethernet cable and connect it to the power and then you can connect to it but since it isn't connected to my router which is upstairs i can't access websites neither can I play on my ps3!I don't know does only ap mode works when it is connected to the router wired because what happens is if you don't put ethernet cables in the back of the dap-1522 and just connect it to power then here doewnstairs you can connect to the dap-1522 my signal is like 87% but while I'm connected with my laptop I can't access websites and in the ps3 I can't connect!
and choose access points there are (4) listed: dap-1522, dap-1160, dap-1353 and dap-2553, I thought of buying dap-1522 because it could support abgn while 1160 only supports g and 1353 only supports n to repeat to signal here downstairs and be a good access point!
View 3 Replies
View Related
Mar 12, 2012
I have a WAP54G v3.1 running firmware version 3.05.01 and a WRT54G v3 running Tomato v1.28. The WAP54G is configured client mode and works perfectly. However, I was not able to get the two to communicate with WPA2 security - maybe, I just didn't try hard enough? Both devices are capable of doing WPA2 with AES but client mode doesn't seem to work with WPA2? I had to drop back to WPA-AES to make it work. Why is this?
View 4 Replies
View Related
Oct 28, 2012
Will i need another RFS6000 controller to run a single AP650 (isolated remote location) or it can be set in stand-alone mode ? I might consider install one antenna per location in 5 different store.
View 6 Replies
View Related
Nov 16, 2011
we have 2 Access point WAP610N. The after some time goes in stand by and we doesn't able to connect to it. We updated at last firmware (1.0.02 build 3, Feb 25, 2011 ) Timeout inactivity 3600 Renewal key 600 Protection WPA2-PERSONAL
View 1 Replies
View Related
Mar 23, 2013
Devices are 3750-24TS Switches, software version is 12.2(55)SE6. how to troubleshoot this issue, I have a pair of ports which are not bundling, no matter what. Is the same behavior with LACP or PAgP. In this outputs I have only the PAgP case.
Output is similar to:
Group Port-channel Protocol Ports
------+-------------+-----------+-----------------------------------------------
12 Po12(SD) PAgP Fa1/0/23(I) Fa1/0/24(I)
Configuration on ports is simple:
SW1:
interface FastEthernet1/0/24
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 12 mode desirable
[code]....
View 3 Replies
View Related
Jul 14, 2011
I have a customer who bought Cisco Aironet 3500 Series. Currently 4404 WISM Controllers are installed with 1142 Access-Points. The WLC-Version is 6.0.199.
Will the 3500 Series Access-Points work? (Of course without the spectrum intelligence feature)?
The Q&A says the following: Are there any concerns with supporting the new Cisco Aironet 3500 Series Access Points with the older Cisco 2000, 2100, 4100, or 4400 Series Wireless LAN Controllers?
View 2 Replies
View Related
Sep 29, 2012
I have had the EA 3500 router for about three months.
The Parental Control of Cisco Connect Cloud block all site except YouTube ! I have the Parental Controls set up to "Block the Internet" at "Specific Times". The other popular sites are blocked: Facebook, The Chive, Tumblr, etc. But for some reason she is still about to view YouTube all day long!
It has the latest firmware. I spent about three hours on the phone with Cisco tech support about this. They uninstalled and re-installed the router - it still doesn't work!
View 4 Replies
View Related
Sep 6, 2011
Is there any chance the Wireless Repeater mode work with WPA2-AES ?If not, which model of AP should I buy to connect it with my wap54g as Wireless Repeater?
View 4 Replies
View Related
Jun 29, 2012
I bought cisco AP (air-ap1142-e-k9) and we know this ap works with 802.11a/g/n same the description note on the package cartoon but my problem is when i configure that ap its work only with 802.11a/g i tries to make it works with 802.11n but fail .
View 3 Replies
View Related
Jan 16, 2012
Whenever my main PC is turned on, i get no signal from the wireless, like i cannot use my phone or laptop on the internet i use an Ethernet cable which is directly connected to my main PC my windows is also window XP and my modem model is TG782T only if my PC is turned off the wireless works
View 2 Replies
View Related
Jun 16, 2011
I purchased a used Compaq laptop with a Realtek USB wireless adapter. The laptop came with XP Pro. I connected the adapter and everything worked great. My husband got a virus I couldn't remove. I have the CD for XP Home so I did a clean install.Windows works fine. I connected the USB wireless adapter and ran the installation disk. When I open Realtek to connect nothing appears in the available networks. I checked the device mgr and it says Realtek is working. I turned off my 2Wire gateway and then reconnected it. I doubled checked that the Windows wireless utility is disabled. Still no available networks. Everything was fine before the reinstall of Windows XP Home.
View 5 Replies
View Related
Jan 16, 2012
Whenever my main PC is turned on, i get no signal from the wireless, like i cannot use my phone or laptop on the interneti use an [COLOR=blue !important][COLOR=blue !important]ethernet[/COLOR][/COLOR] cable which is direclty connected to my main PCmy windows is also window XP and my modem model is TG782T
View 2 Replies
View Related
Mar 6, 2013
I´m trying to test anntenas in a AIR-CAP3062E-A-K9 the problem is that when I´m below the AP the speed is weak, the AP es with a WLC, so I was wondering if do you know a command or a form to test the anntenas or the Radio.
View 7 Replies
View Related
Dec 26, 2011
reset my Linksys E1000 and now I can't access wifi from my phone as neither my pw or my default ps work.
View 2 Replies
View Related
Jan 15, 2012
like today randomly my internet went down. And then everything changed back to its original like my SSID from Netcom it changed back to wireless and everything was default and also the PPP was off so i wasn't able to connect to the internet. So i went to my router setup page on the internet or whatever and turned it back on. So now like the internet on my computer which has a cable to the router works but the wireless internet doesn't work for my laptop nor ipod. I can see the connection on the laptop and ipod but when i try to connect it keeps saying that it is unable to connect.
View 7 Replies
View Related
Mar 25, 2011
I installed a Micro Edition of Windows 7. Everything is going properly with it except the wireless internet connection (its driver is installed and working properly as shown in Device Manager), by click Connect and typing the PW, it tries for few minutes then fail in connecting putting a yellow small circle on the wireless icon in Task bar
View 1 Replies
View Related
Mar 8, 2012
I upgraded my computer with a new graphics card and power supply. When I turned it on everything ran fine except for the internet. I either get a connection with 1 bar, a connection but no internet acess, or no internet at all. Did I damage something on the motherboard that could cause this?
View 11 Replies
View Related
May 2, 2011
My wireless is connected fine but the internet wont work.I have internet explorer and firefox and it doesnt work on either.
View 1 Replies
View Related
Feb 16, 2013
My fn f8 button doesnt work and doesnt seen when i click. and my wireless doesn't work. I tried to download new driver but it didnt work too.
View 1 Replies
View Related
Mar 29, 2011
I have this Belkin wireless g router, which I had for a year. I was using the wired connection since then until I, at last, was able to use it's wireless connection but it only lasted around a week. After that, the modem light on the router kept on blinking and the internet light wouldn't turn on. I also couldn't connect to the router anymore(wired and wireless), neither could I configure it. I reset it but it still didn't work.
View 1 Replies
View Related
Oct 7, 2011
I finished building my computer today, installed a fresh os and all the necessary drivers that came with the dvds provided, yet the wireless card doesn't even appear anywhere in the computer. The ethernet cabled one does, but not the wireless. Trying to connect to anything wireless just gives an endless searching process, with no results. I can't test the ethernet either, my router is all the way into the living room, way far out of reach.
Specs:
MB: Asus M4A88TD-V EVO/USB3
GPU: Asus 6870 HD
CPU: AMD Phenom II x4 955
I don't think anything else is necessary, is it?
View 1 Replies
View Related
Aug 10, 2011
The DIR-825 wireless simply doesn't work. When I called tech support, we cleared some settings and hard-powered the unit on/off and it finally turned on the wireless radio. A couple weeks later I pull out my laptop to use in the house via wireless and the wireless on the DIR-825 is OFFLINE AGAIN...fallen and it can't get UP.Is anyone having issues with keeping their wireless online? OK - powered it off for 5 minutes...now the wireless is working. I think changing configuration settings causes the thing to lock up.
View 1 Replies
View Related
Jan 7, 2011
Seems like there those saying they have gotten there DIR-655 and XBOX 360 Wireless N Adpater to work in 802.11n mode. The adapter will only connect in 802.11g mode (and yes I have the correct adapter). I have set the settings to following
802.11 Mode: Mixed 802.11n and 802.11g
Wireless Channel 2.462 ghz - Ch 11
Transmission Rate Best
Channel Width 20/40
WPA-Personal
WPA2 Only
Cipher Type: AES
Does this router really work with XBOX 360 Wirelss N Adapater. If so, how has others got this to work.
View 3 Replies
View Related
Jan 7, 2013
Trying to troubleshoot a Cisco Pix 501. We have a cable modem/router that goes to the Cisco box that then goes to my wife's computer. It's worked flawlessly since we hooked it up, even if we unplug/replug the router. Today, we unplugged the Cisco box itself to hook up a newer one. When the newer one didn't work, we tried to hook up the old one again to no avail. The led indicators seem to show that everything's working properly. We've unplugged and rebooted everything. Nothing works. The network monitor on the computer shows that it detects being connected to a network, but it always says no internet access.
View 1 Replies
View Related
May 5, 2013
i've upgraded our WLC 5508 from 7.0.220 to 7.2.115.1.For our guest WLAN we use web authentication with customized startpage, no login error page and no logout page. The customized login page is displayed correctly. After successful authentication the browser is forwarded to the default CISCO login page "login.html". No further autentication is possible, also no internet access.Reload the customized webauth bundle to the controller didn't change anything. Is there a change in the HTML/Java code of this controller version? I didn't find any hint in the release notes. Or do I need the newer web authentication bundle with version 1.0.2?
View 6 Replies
View Related
May 12, 2013
It looks like pretty basic config, but it does not work. I have 1x 2602i autonomous mode AP, 1x C2960 switch (with inter-vlan routing prefered SDM template) and 1x 1841 router.
I trunk between Switch and Router works smoothly, but it does not work between AP and Switch or AP and Router.
Configuration looks like this:
AP2602i:
interface GigabitEthernet0
no ip address
duplex full
speed 100
[code]....
View 12 Replies
View Related
Sep 11, 2012
I just upload firmware1.0.1.10 on 2 WAP121. After the update and reboot, I was able to confirm the firmware version in the System Summary menu. The update is uneventful.However, the functions WDS Bridge and WorkGroup Bridge no longer works on two WAP121:
- For WDS Bridge, when I configure a Remote MAC Address with WPA Encryption and then I click on the Save button, nothing happens there. But it works well when I choose without Encryption.
- For WorkGroup Bridge, when I click on the Save button (even without changing the configuration), I have a message "Certificate file uploaded successfully" and another error message in the background: "error occured for query you send path . device.sync ... "
1.0.0.3 firmware is not available on your site, it is imposible for me to go back.
View 2 Replies
View Related
