Cisco Wireless :: CT2504-K9 / WPA2-TKIP - IPad And IPhone Not Connecting To WLAN?
May 22, 2013
I´m trying to connect them to my WLAN, for throubleshoot I create a new WLAN with WPA2-TKIP and a PSK, the devices didin´t connect to the WLAN.I also change the security to WPA2-AES with TKIP, it didn´t work too.
My best choice was to disable every security configuration in order to began the throubleshooting from zero, but even with no Layer 2 and 3 security, the devices didn´t connect to my Test WLAN.
I´m using a AIR-CT2504-K9 WLC with two AIR-CAP3502I-A-K9 AP, all the PCs and other brand cellphones and tablets work well.
Also I have a SOHO router on the office, and the IPad connect without a problem with that WLAN, but I need them to connect to my Cisco AP.
IPods and IPads to connect to stand alone AP1131? My scenario is as follows:
There is a section of a campus that is covered by 14 stand alone AP1131 were I experience the problem. The security parameters are: 802.1x, wpa enterprise, tkip
The other section is under WLC also AP1131 but in this case in WLANs/Scurity/Leyer 2 I checked boxes:
Wonder if the fact that I chose WPA2, AES makes a difference with stand alone mode? Anyways I tried configuring AES in stand alone APs and it didn't make a difference since I could not connect either.
Region : India Model : TD-W8951ND Hardware Version : V4 ISP : MTNL
I m using TD-W8951ND wifi router with MTNL connection. The LAN connection with PC works just fine but i m not able to connect my iphone or ipad with the router. I have reset the router many times and also retored my iphone but still no luck. Pl tell me what are the settings needed for wifi connections.. Currently i have set the wireless mode to 802.11 b+g+n. Setting it to just 802.11 b sometimes connects with the iphone but never with ipad.
I am looking to purchase the RV220W router. I am interested to know if I can use the iPhone/iPad to create a VPN connection to this router.I have seen a lot of conflicting information about this so I am looking for a confirmation.
My iPad cannot connect to my network wireless through WPA2 using router E4200 the way my Macbook is connected. Only using guest access i can get internet contact. Is this a known problem with this combination and/or is it meant to be, that only guest access gives an iPad connection?
We are implementing a new corporate wireless network with Cisco 5508 WLC's and C3602I LWAP's. We are not running any RADIUS or EAP at the moment and are starting with WPA2 w/ AES with a pre-shared key to begin piloting. The issue we are having is iOS based devices (iPhone/iPad) do not seem to want to connect. We just get a could not join wireless network messages. We have had success with several Windows based laptops, my MacBook connects, as well as several different Android devices.Looking at the logs on the WLC I see these entries which correspond to the MAC address of my iPhone.
*apfMsConnTask_6: Jul 17 17:25:20.620: %APF-3-CHECK_SUPP_RATES_FAILED: apf_utils.c:376 Could not check supported rates. Missing Supported Rate. Length :0. Mobile MAC: 24:ab:81:92:4d:97.
on a 5508 WLC can we create new SSID for I PAD / IPHONE Users without having ISE, only I phone / I PAD are allowed to be authenticated rest all should be denied. IS this possible?
I recently connected E1500 to time wanrner cable modem for my home. 3 laptops work fine, but iphone and ipad can not connect to wireless. But iphone and ipad connected to linksys guest automatically.
We have a centralized WLC with some branch office with AP's in Flexconnect Mode. The Wlans are configured to use Web Authentication (Landing Page). The Landing Page is Cisco Default.
We're experiencing some problem with Apple Devices, on some the Landing Page apperars on some not. The WLC Software is about 1 year old. On a XP machine the landing page doesn't appear too, but you can type in the address manually and it works.
Whats the best solution to include the Apple Devices successfully in the WLC Wireless World.
Can a WAP4410N be used as a repeater on an existing WPA2 + EAP-TLS WLAN? The existing WLAN is on a Cisco 871W router; we hope to use a WAP4410N as a repeater to extend it.
I've not had much luck so far with the "repeater" and "WDS repeater" AP modes on the 4410. I'm either configuring it wrong, or perhaps the 871W needs a config tweak? Or perhaps the 871's wireless can't be repeated like this?
Does my Belkin F5D8236-4 ver. 1 (firmware 1.00.02) router support Apple's Bonjour print application. I can't get my iPhone or iPad to recognize my new HP Photosmart 7520 wireless printer which is connected to my network through my router.
Is it possible to make Any Connect VPN from IPad/iPhone to 871w? IPSec VPN is working perfectly but cant get my Cisco AnyConnect iOS client to connect. I have config webvpn and it beeing user/pw prompted but keep getting the following error:
"the required license for this type of VPN client is not avaiable on the Secure gateway. Please contact Your network administrator".
My pc was working fine till I shut it down n restarted it and now it won't connect to the Internet I am running windows vista 32 bit service pack 1 and is wired to my router but I can connect my ipad(which I'm using now) and iPhone through wireless
I just setup 3 webcam DSC-930L for a friends with a router DI-655.
I run the setup for the 3 webcams. If I use my dlink on the local network it work, if I used my dlink from let say at work, it work too. If I used the i pad in WiFi it works.
The problem is when I try to use the i phone or the i pad in 3G mode, sometimes it work but most of the time it doesn't, after about 60sec it says something like check your network settings... When I'm able to see something in my dlink app on the i phone, if I return back to the list after that it doesn't work if I switch camera.
Question is, do I have to forward any port on the router in the virtual server section? I'm assuming no since sometime it work and sometimes no. Do I have to activate the UpnP on the router too?
How to make a non-client VPN connection to the RVS4000 SBR with an iPhone or iPad? I realize that I could setup some pass-through VPN just fine, but I would like to connect directly to the router and was under the impression from the Cisco product video and other research that IOS was now supported.
Currently the ACS 5 is authenticate the iPhone/iPad by using the MAC address (which is entered manually) and AD user/password, i need to do that with certificate, so it will be scalable.
I have an ASA5540 running AnyConnect premium (25 users). I know that I need the AnyConnect Mobile license in order to use an AnyConnect client on the IPADs/Iphones. My question is - can I do clientless SSL VPN? Do I need the AnyConnect Mobile license for this?
We're in the process of implementing an ISE 1.1 server for Guest Wireless Access / BYOD at our company and ran into an issue with authenticating from iPhones / iPads when the account is set with 'change password on next logon' (it's a local account created on the ISE server - not AD). It fails and displays 'unable to join network' on the iPhone. The ISE log shows a '5411: No response received in 120 seconds'. We're able to authenticate from Windows devices and are prompted to change the password during the authentication process. If we unchecked the 'change password' box we can authenticate from iPhones & iPads without any issue but we need to have a way for users to set their own password.
I really worked hard not to write this question here but here I am. I am trying to route all traffic through vpn but I cant browse the web. It seems no traffic goes through the vpn tunnel. Split tunneling works but it doesnt route the traffic through vpn tunnel. I have a cisco asa5505 with base license,
When I try to browse the web with one of the clients I see lots of
6Apr 07 201309:40:5510.10.50.136088410.10.10.153Built inbound UDP connection 834 for outside:10.10.50.13/60884 (10.10.50.13/60884) to outside:10.10.10.1/53 (10.10.10.1/53) (xxxx
messages but at the end I see " Safari could not open the page because the server stopped responding" message or smth similar.
I have an issue with my home network that is really stressing me out now. I have a Thomson TG585 v8 router that my laptop, iPad and iPhone connect to no problem but my iPad/iPhone won't talk to my laptop.. I want to be able to use my iPad to remote in to my laptop to watch movies etc. Network sharing is on the laptop and I've checked that all devices are on the same network..I can't ping the iPad or iPhone from the laptop either.
My iphone wireless connectivity to my Linksys router that I have put up with for a year, but as I now have the same issue with my ipad I've decided enough is enough.The issue is that they both connect OK to the router and therefore to the internet, but after a short period of time (minutes) whilst it appears that they are still connected to the router the connection seems to completely hang. At that point I have to go into settings on the iphone/ipad and turn off the wireless connection and turn it on again. This then allows connectivity and internet activity for 5-10 (15-20) minutes before it hangs again.I have no problems with connecting to any other router from the iphone and ipad. And I also have no problems with my PC's connecting to the Linksys router.
I have local WI-Fi network with 2 Macs, 2 PC's, iPhone, iPod and i Pad at home on Link sys WAG120N router. On i Pad when I try to connect to Internet I have to turn WiFi off and on. It works for a while but after waking i Pad from sleep I have to switch off and on again. It really drives me crazy. Sometimes (hardly ever) it happens on my iPhone 4 (same network setup as on i Pad). Other devices connect to Internet whenever I need.
My use case is very simple I want to connect iPhone/iPad using pptp to my home network. I purchased the 180W and looks like I am not able to connect mobile devices to it. My Setup is simple I have ST536v6 (firmware 7.4.4) modem in bridge mode and Cisco RV 180W connect to my ISP using Ppoe. I followed the Admin guide and created the pptp user. If I connect from internal network it connects but when I try to connect the device from WAN it just does not work.
I have a Wag 160n router which works fine with desktop pc connected by ethernet & wirelessly to laptop. My nokia phone finds the wi-fi signal but apple i-phone & ipad dont!
I have an ipad that is not able to connect to a 1142 Autonomous AP. This AP was originally a light weight AP and then downgraded to autonomous.A strange thing i see is that the AP shows me only two radios. 802.11 N(2.4 GHZ) and 802.11 N(5 GHZ). I suspected the AP not to support the b/g networks. i then downloaded the most recent software but i still cannot get it to connect and on the AP's GUI i only see the above two mentionned radios. i tried to connect to two SSID's. one using WPA2 and another with open authentication and no security.but this does not work. Is it possible that some 1142 do not support b/g networks?
recently we have purchased Reflection - an AirPlay mirroring software. Basically install Reflection in the laptop and you can view the screen of the iPad or iPhone via wireless network. we have tested in home wireless network no problem, but when connect to the cisco network, the iPad didn't recognize the REFLECTION installed in the laptop.
we are running WLC 5508, WLAP AP-1331AG, we can ping from laptop to the iPad laptop and ipad can access network without any issue. there is no any application port has been blocked between the client via wifi extra details for REFLECTION: [URL]
