Cisco Wireless :: Does VWLC Support AIR-AP1231G-A-K9 Platform
Mar 6, 2013Does the Cisco vWLC support the cisco AIR-AP1231G-A-K9 platform?
View 4 Replies
ADVERTISEMENT
Cisco Switching/Routing :: NAT-PT IOS Support 7600 Platform?
Dec 22, 2011I´m looking for an IOS on a 7609 SUP720/MSF3 that supports the NAT-PT feature (IPv4 to IPv6 translation). I searched on the Cisco Feature Navigator but the tool didn´t show up any IOS for the 760x platforms. I only got the feature "NAT-PT: Support for Overload (PAT)" with IOS 15.xS train.
View 2 Replies View RelatedCisco Switching/Routing :: 3750 - Platform Does Not Support More Than 32 HSRP Groups?
May 6, 2012I got the error in object when I try to add a new HSRP group in new vlan.All the HSRP group has the same HSRP group the 2.another way to provide clients's default gateway redundancy for each Vlan intead to use the HSRP?
View 4 Replies View RelatedCisco Wireless :: VWLC - 1142N AP Not Broadcasting SSID?
Apr 7, 2013I am running the demo of the virtual WLC and have one 1142N AP connected to it. I have two WLAN's created and they are configured to broadcast their SSID's. However, when I look on my laptop or Android, I cannot see either of them. I checked the AP to see if it has the WLAN's on it and it does. I did this by going to Wireless -> Access Points -> Radios -> 802.11a/n AP Interfaces -> Details. Under Station Configuration Parameters -> Number of WLAN's, there are 2, which is correct. I had this demo running on VMware workstation and had some bridging issues with it and thought that was the issue. I now have it running on ESX5.1 and am still having this issue. I am at a loss as to what is causing this problem.
View 2 Replies View RelatedCisco Wireless :: VWLC IOS 7.3.112 And 2602e AP Unable To Join Mac
Mar 7, 2013Below are the errors that i am getting while trying to register AP (2606e) with vWLC (7.3.112) .
That is the error on vwlc
[code]....
But in wlc statistis we are able to see the ap join mac, screen shot is attached
Cisco Wireless :: 1130AG APs / VWLC 7.4 LAP Flexconnect Configuration
Feb 17, 2013i have installed ISE1.1 on VM and other hand vWLC7.4 also there in VM i am using 1130AG APs in flexconnect mode and using central auth and central switch.i wan to configure it for CWA(central web Auth) from ISE but a little a bit confuse about ACLs.
View 2 Replies View RelatedCisco Switching/Routing :: Deploying A Virtual Wireless LAN Controller (vWLC 7.3)
Mar 13, 2013I am looking at deploying a Cisco Virtual Wireless LAN Controller (vWLC 7.3).
Do I need Prime Infrastructure to manage the environment, or can I manage my AP's (1200 series) using the vWLC alone?
Cisco Wireless :: 1131AG Can't Pass Traffic When In Centrally Switched Wlan Using VWLC
Sep 9, 2012Im using 1131AG AP.Locally switched WLAN don't have problem.Authentication used: open/wpa-psk/wpa2-psk.Pinging the IP Address of the vWLC dynamic interface (WLAN-SSID Mapping) is ok, but with the gateway failed.
View 12 Replies View RelatedCisco Wireless :: VWLC And Aironet 1252 - All Client Devices Such As IPhone / Laptop Can't Find SSID
Sep 6, 2012I'm facing a problem on vWLC. I configured the vWLC and Aironet 1252, I created 2 SSID with below settings.
1. WPA2 Auth 802.1X
2. Web-Auth
Inside Wireless, I configured this AP Mode as "Local", but all of the client device such as iPhone, Laptop can't find these SSID.
Cisco Wireless :: Using AIR-AP1231G-E-K9 As Repeater?
Apr 24, 2012I have an AIR-AP1131AG-E-K9 running as root AP with three SSID's (mbssid), all WPA-2 PSK, IOS 12.4(25d)JA Now I would like to use an AIR-AP1231G-E-K9 as repeater for one of the SSID's (all three are AFAIK not possible), IOS 12.3.8-JEE(ED) So only one SSID is used.
I use exactly the same shared secrets and security settings on both devices, on the repeater the SSID is designated as infrastructure-ssid.Unfortunately I have the problem that the repeater AP cannot associate with the root AP.I have verified that aironet extensions are enabled, same security settings are used and checked many sites on the net which describe how to configure a repeater AP. Is there any incompatibility between these two APs? I have two of the AIR-AP1231-G-E-K9 APs available, do I need to use the same models?
Cisco Wireless :: Adding A Second Ssid Air-ap1231g-a-k9?
Jun 20, 2012Version 12.3 I currently have an open authenication customer network, I would like to add a second securt ssid for my sales department, is this possible, how do I do this, the more specific the better .
View 1 Replies View RelatedCisco Wireless :: WLC 2504 Works With AIR-AP1231G-E-K9 And AIR-BR1310G-E-K9?
Feb 3, 2013Does WLC 2504 works with AIR-AP1231G-E-K9 and with AIR-BR1310G-E-K9 after I upgraded form AP to LAP the AP ?
View 4 Replies View RelatedCisco Wireless :: AP1231G - Failed To Add Device To WCS Reason
May 10, 2012I am trying to add an AP (1231G) with autonomous code (Version 12.3(8)JEC2) to WCS (v7.0.172.0). I recieved the following error:
Failed to add device to WCS Reason: Unified AP with same MacAddress already exists in WCS. Remove Unified AP first.
Cisco Wireless :: Radius Server Authentication AIR-AP1231G-A-K9
Apr 30, 2012Below is he output from debug radius authentication from my AP.
I can see request is forwarding from AP to radius but Radius is not sending any response.Not sure why its not responding.
I also did not under stand few out outputs also
no sg in radius-timers and
RADIUS/DECODE: parse response no app start; FAIL
what does it mean.
I restarted radius server , changed secret key but no luck.
019639: May 1 16:15:08.727: RADIUS: User-Name [1] 32 "host/3KYGRH1.idcap.intdata.com"
019640: May 1 16:15:08.727: RADIUS: Framed-MTU [12] 6 1400
019641: May 1 16:15:08.727: RADIUS: Called-Station-Id [30] 16 "0012.01d6.f691"
[Code]...
Cisco Wireless :: Strange Power Failure With AIR-AP1231G
Mar 25, 2012I'm having the following issue with a couple of 1231's.
Some overall config info first:
This is a small office with 2x Catalyst 2950 (24-port, no PoE) switches and 4 AP1231G (autonomous). The APs get PoE from a PWRINJ3 each. The injectors are powered by the AP power supplies. Injectors and power supplies are mounted in the patch closet.
The 2 switches are connected together over 4 ports (20-23 on each switch), these ports are set to 1Q Trunk mode.
The APs are connected to the switches, 2 to each switch, on port 1-2. These ports again are configured as 1Q Trunk.
APs are connected to the switch as follows:
[switch] <- patch cable-> [injector] <- patch cable -> [patch panel] <- static cabling -> [outlet] <- patch cable -> [AP]
All this has been working without problems for a number of years.
A few weeks back, AP2 did not restart after a power cut (everything else did). All LEDs are off, port on switch has no LEDs lit. I did not get around to investigating this furtehr until last week. I unmounted (failed) AP2, took it to the spot where (working) AP3 hangs, and plugged it to the cable of AP3. AP2 came to life immediately. I unplugged it and plugged AP3 back in, which restarted immediately.
So I suspect a power supply issue on AP2. I took the injector and power supply that fed AP2 out of the patch closet. When connecting AP2 directly to the power supply, it came to life immediately. So I figure the injector is defective.
On the same day, I notice AP4 is also dead (again all LEDs off, no idea how long, could have been that day or could have been a few days - it has definitely been working after the power cut that appeared to have killed AP2).
So I order 2 new PWRINJ3s and for good measure 2 new power supplies. Later that day, I took the injector and power supply that fed AP4 out of the patch closet. When I try this combination (AP4, injector4 and P/S4), and connect it to a different wall outlet (and therefore a different port -16 - on the switch) IT WORKS! Should have triggered questions, but did not immediately.
Last Thursday I got the new injectors and power supplies. So I take one of each, hook them upto AP2 at my desk, and AP2 starts up. So I mount new injector2 and new P/S2 in the patch closet, put AP2 back in its place, connect all the cables - NOTHING. AP2 does not start. The "power" LED on the injecvtor lights up green, the "device status" LED remains off. I take AP2, new injector2 and new P/S2 to my desk, hook them upto a wall outlet (connected to switch port 17). AP2 starts immediately.
Meanwhile AP3 has (also) stopped working (no LEDs on at all). As far as I can tell, it stopped working after I briefly disconnected (and reconnected) the patch cable between injector3 and the patch panel in the patch closet. The LEDs on switch port 1 are off.
I have since tried to power cycle both switches (took power off both, waited a while, poewerd both back on). No change.
PS: the APs ran firmware 12.3(8)-JA until recently. AP1, AP3 and AP4 were upgraded to 12.3(8)-JEE after the the power cut that took AP2 out. THis is when I found out AP2 was dead. AP2 was still on 12.3(8)-JA. It was upgraded to 12.3(8)-JEE last week when it was on direct power on my desk.
Cisco Wireless :: AIR-AP1231G-A-K9 - Replicating Setup Across Heterogeneous APs
Oct 17, 2012I am trying now to deploy the setup that works on some APs and doesn't work on others.
For example, on an AIR-AP1231G-A-K9, the following setup works:
!
version 12.3
no service pad
service timestamps debug datetime msec
[Code].....
Cisco Wireless :: AIR-AP1231G-A-K9 And Controller Based Environment With Prime NCS
Apr 15, 2012I can't find any information that the AP1231G-A-K9 AP is supported in a 5508 Controller Based environment with Prime NCS.Could one of the experts confirm or deny?
View 1 Replies View RelatedCisco Wireless :: Replacing AP1231G-E-K9 (LEAP) With New 1260 / Will It Work
Aug 24, 2011iam currently trying to replace AP1231G-E-K9 with new equipment / Cisco AP next generation maybe?The problem is that the system, that is going to use the AP is using aironet 350 PCMCIA adapter with LEAP. If in fact we are going to use a new Cisco AP, will the new generation work with Aironet 350 Adapter and support LEAP?
View 2 Replies View RelatedCisco Wireless :: AIR-AP1231G-A-K9 Standalone Access Point- Disconnection
Jun 9, 2013We have this access point AIR-AP1231G-A-K9 for mobile users. current version is c1200-k9w7-mx.123-7.JA4. Sometimes users are able to associate but not getting IP address from dhcp. It shows 0.0.0.0 for the particular client.
View 2 Replies View RelatedCisco Wireless :: AIR-AP1231G-E-K9 - Upgrading Autonomous Access Points To Lightweight Mode
Jun 6, 2013I have AP AIR-AP1231G-E-K9 with iOS c1200-k9w7-tar.123-7.JA2 and I want to convert it to Lightweight Mode with iOS image c1200-rcvk9w8 tar.124-21a.JA2. First of all, is it possible? Because I tried to convert from tftp server command (archive download-sw /overwrite /reload tftp://ipaddress/image.tar) and I cannot see in the controller. (controller and aps are in the same network)
View 11 Replies View RelatedCisco :: AIR-AP1231G-A-K9 Management IP?
Nov 18, 2012I have two dinasour APs that I need to fix. They are configured in bridge mode to bridge a few VLANs between two sites. Right now the management IP on BVI 3 interface doesn't work. Does it have to be on BVI1 for it to work? When I say "work" I mean I am able to ping it and use SNMP to monitor it.
View 1 Replies View RelatedCisco :: Ap1231g-e-k9 - Load New Bin Ios In Rommon Mode?
Jun 9, 2011loading a new bin file onto a Cisco wirless access point ,the access point i have found is only in rommon stage
Access point model is : ap1231g-e-k9.
Cisco Wireless :: Upgrade C240 MSE Platform Size And Maintain UID?
Mar 6, 2013When we originally deployed our Cisco Prime NCS and MSE Virtual Appliances, the VMsphere server they were on was not able to assign us the level of resources we requested. We installed the MSE as "LOW" system due to the memory and CPU requirements. It has a 2000 CAS element limit. At the time we were licensed for 1000, so no huge problem.
Now, we purchased a Cisco UCS C240 server to run our Prime NCS and MSE on, which gives us our own environment where we have plenty of resources. I also bought 6000 CAS element licensing.
The catch is, how can I either do a fresh install, using the same UID, on our new UCS server, so that our licensing is still valid when we move the box, or, is it possible to do some sort of platform reinstall or upgrade after moving our original MSE VM guest over to the UCS server? Sadly, I can't even utilize the additional 1000 CAS element licensing at this time because it won't allow me to add the 6000 license and use only 2000, on the LOW appliance. So I've got to get these VM guests moved, but maintain any UID's so that the licensing still works.
Is it possible to disconnect the licensing we have, from the UID, and move it to a different UID?
Cisco :: AP1231G-A-K9 Access Points / Very Slow Throughput
Jul 17, 2012I recently setup our small office network using the following setup:
Cablemodem <--> router <--> 1231AP(role root bridge with wireless clients) <-> 1231AP(role non-root bridge with wireless clients)Code on both APs: 12.3(8)JEE.Office network generally has less than 3 wireless clients connected at any one time to either AP. AP's are a mere 50' apart; clients are all less than 30' from either AP; they all show excellent signal and connected at 54mbps signaling rates.
All is/has been working very well & very stable with the exception of speed. We have business class service from RR, approx 25mbps dl, 2mbps ul. Any hardwired client to the router switch ports are able to download at speeds averaging 23mbps. Any wireless client connected to either AP is never able to exceed download speeds of 5mbps. With no other wireless clients connected except my one test client, I was not able to exceed 5mbps throughput from either AP that I connected to.
I can confirm that the ethernet connection between the router and root bridge is up at 100mbps-FD and not showing any errors: [code]
Are these very slow thoughput speeds normal of this hardware combination?I did much searching/googling and found claims that by eliminating TKIP it almost doubles the actual wireless speeds our clients can obtain.
Wireless :: Can Wireless Router Support Up To 100 User Including Support Network Printer
Feb 16, 2011can wireless router support up to 100 user including support network printer
View 1 Replies View RelatedCisco AAA/Identity/Nac :: C220 ISE On UCS Platform With UC
Mar 7, 2013We are looking to deploy ISE supporting 5000 devices and would like to use the Cisco UCS platform to host this. Looking at the spec required a C22 M3 would be sufficient; however we would also like to host some UC applications on the same server if resources allow.
Therefore we would like to deploy ISE on a C220 M3 server and connect the associated NIC to a DMZ. We would then like to deploy UC applications such as CUCM and CUPS on the same UCS server with a NIC attached to the internal network.
Also while the UC application would require a UC Foundation License (R-VMW-UC-FND5-K9) whould this also meet the requirements for ISE?
Cisco WAN :: ONS 15454 SONET MSPP As Platform
May 26, 2011I am doing a school research project in which I am setting up an OC-192 ring for a company (contract work through AT&T). I have chosen to use the Cisco ONS 15454 SONET MSPP as my platform. The company currently has locations in Chicago and Philadelphia and connects them through an OC-12C ATM connection and they are looking to add 2 gigabit ethernet connections.My question is what cards and parts will I need for the Cisco ONS 15454 SONET MSPP, and how much will everything cost? I have been searching the internet for components and prices and I have found it extremely difficult to find any information.
View 2 Replies View RelatedCisco WAN :: Recommended Router Platform As 2951
Oct 17, 2012I currently have a 50Mbps Internet Connection provided by an ethernet handoff for hosting some webservers. We are looking at adding an additional 10Mbps Internetn connection and route BGP between the two. For the 50Mbps connection, i'm using a Cisco 2951 router. I also have another 2951 router to terminate the 10Mbps connection. Does these router have enough horsepower to fully route BGP?
View 1 Replies View RelatedCisco Security :: Migrating From 3030 To ASA Platform?
Jun 13, 2007Is there any way to auto migrate my 3030 VPN configuration to an ASA platform?
View 3 Replies View RelatedCisco WAN :: 3560G What Platform And IOS Version Need To Implement IOS SLB
Nov 27, 2011I want to select catalyst 3560G for my network. But IOS SLB need to be implemented in my network. I only know catalyst 6500 series can support this feature and i am not sure whether 3560G can support this feature. what platform and IOS version i need to implement IOS SLB?
View 1 Replies View RelatedCisco VPN :: ASA5510 - SSL Essentials And SSL Premium On The Same Platform
Mar 22, 2011A make one BOM and i just ask my self can we order on the one platform ( for example 5510-SEC-BUN-K9 ) SSL Essentials license ( this license is on the platform by default we buy 250 users ) and i need 50 Users license from them to be Premium.
Can i buy those two license on the same platform and is this will work ?
Cisco WAN :: 2911 Platform - Clear Interface On IOS 15.1
Jan 3, 2012During WAN troubleshooting, I did a "clear interface ser0/0/0" on a branch router. It has two WAN links. I lost ssh/telnet connectivity but both WAN links were still replying to pings. We did a manual power off of the router to regain connectivity.Is there a known issue with this command on this IOS version? We're using Cisco 2911 platform with IOS 15.1-1.T2 version.
View 1 Replies View RelatedCisco Firewall :: ASA 5505 Voice Platform - Firewalls
Apr 23, 2012I am currently working on our Cisco voice platform at work.
Our Cisco firewall engineer has left and I have been given the task of looking after the firewalls as our Chief Exec seems to think that Cisco Voice is similar to Cisco ASA firewalls,
Are there any books/videos out that you can recommend to learn the about firewalls quickly.