Cisco Wireless :: Registering CAP 3502 In WLC
Nov 14, 2012
I have a Cisco Wireless LAN Controller AIR-CT5508-K9 running Software Version 7.0.98.218. This WLC has registered ten AP model 1240.Now I have configured fiive CAP3502 with static capwapp commands, when I connect the CAP-3502 in the network, in the WLC I see the status "downloading" then the CAP restart, and the console show the message *Mar 1 00:15:39.033: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER, and never the CAP3502 is registered in the WLC. [code]
View 1 Replies
ADVERTISEMENT
Feb 8, 2013
i have 2504 controller with 7.0.116.0 software and some 3502 APs. I also using 5 APs now and few days ago I bought some additional 3502 APs and I can't get them connected to the controller. My company admins decided to using DNS controller discovery instead of using DHCP option 43. I'm connecting APs to access ports of Linksys switches and APs not in the same subnet as ap-manager interface of controller. AP succesfully get IP and DNS from DHCP and could ping cisco-capwap-controller. However, I have such messages.
*Mar 1 00:12:32.014: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.Not in Bound state.
*Mar 1 00:12:40.533: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.
I can succesfully ping controller from AP AP30f7.0d2e.9a58#ping cisco-capwap-controller Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 10.23.16.30, timeout is 2 seconds:
View 6 Replies
View Related
May 12, 2012
There are a total of 25 Cisco 3502 APs installed. 24 APs were discovered except for 1 AP. I run SH CDP NE on the switch and the AP was discovered by the switch but it does not have an IP address. On the output of the SH CDP NE DE, I noticed that on the AP that is not joining, the Platform is "cisco AIR-SAP3502E-E-K9" while the APs that joined the WLC, the Platform is "cisco AIR-CAP3502E-E-K9". The software versions are also different but this could be because the WLC already upgraded the IOS when the APs joined.Why is the Platform "SAP3502E" for the AP that did not join.
View 9 Replies
View Related
Apr 2, 2012
Just a basic question regarding MAC based authentication of AP with ACS. The scenario is - If I have a ACS installed and I want all my Cisco 3502 APs to be authenticated on MAC basis via ACS. I know that AP mac is used as a username and password at ACS so that whenever we plugin the new AP in the network, it gets authenticated via ACS first and if the AP is authorized to be used in network then only it gets the IP address from DHCP.
My question is - What will happen, if the AP is connected in local mode on a remote location and the WLC, ACS & DHCP are in Data center. The traffic coming from remote location will pass through the Remote-site router and during that pass, it will remove the source mac address of AP and put the router interface MAC address as source, so how will the ACS authenticate the AP in that case.
When working in a LAN I know its possible, but how will it work over the WAN.
View 9 Replies
View Related
Mar 15, 2012
Using WISM with 7.0.220 and 1240 and 3502 APs. Just found that some of our 3502 AP didn't enbale their clean air and CDP when installed. This only happened on a few new APs. But the area these APs where we seem to have had a few problems with PCs. The only PCs effected where Computer On Wheels (COWs), Dell 780 Desktop with a Cisco Wireless Card.
Using an interl wireless card and others in thes areas worked.Once I enabled the CDP and Clean Air, the COWs worked.My question is with the APs not having CDP enabled, could this affect the cisco wirelss card in the COWs?
View 6 Replies
View Related
Nov 27, 2011
I know what the problemis i need to tell the AP what the mac of the switchport is but i can not figure it out because it is a CATos Switch?on a IOS I would just use the Show interface command and use the bia but i dont know how to figure out the bia on a CATos?
View 3 Replies
View Related
Oct 7, 2010
I have a Cisco WLC5508 controller which I recently upgraded to software 7.0.98.0 because I tried to add a Aironet 3502 and it gave me an invalid software. After the upgrade this is the error I get from the AP when I try to add. [code]
View 5 Replies
View Related
Jan 27, 2013
Our newly installed WAP's are constantly downloading code and seem to lose contact with our wism 1 version 7.0.235.3, causing them to restart the downloading process, over and over.
View 12 Replies
View Related
Jan 31, 2012
We have a secure ssid and a guest ssid. Is the a way to prompt for a single username and password and if that name is guest it will automatically connect to the guest ssid? If active directory user and password it will automatically use the secure ssid? we are using Microsoft NPS/Radius, 3502 ap's, and 5508 controller.
View 3 Replies
View Related
Aug 9, 2012
I found the 3502 waps are plenum rated, I found the cable on the antenna are plenum rated, but are the antenna plenum rated?
AIR-ANT5160NP-R?
AIR-ANT2451NV-R?
AIR-ANT2460NP-R?
View 8 Replies
View Related
Jul 5, 2012
I have one 5500 and about 15 Cisco 3502 APs.
The problem is that one of the clients loses the connection to the network time to time ,The error in the WLC logg is
*Dot1x_NW_MsgTask_0: Jul 06 17:42:38.934: %DOT1X-3-INVALID_WPA_KEY_MSG_STATE: 1x_eapkey.c:843 Received EAPOL-key M2 msg has invalid information when mobile is in START state - invalid secure bit; KeyLen 24, Key type 1, client 00:21:6a:af:be:70
View 4 Replies
View Related
Oct 19, 2011
I have got a 3502 setup and functioning in Office Extend mode. I have found one issue though. I have to set the checkbox on the my Management Interface to Enable NAT Address and put the external address in the box. Once this occurs no internal APs can join the controller.
Need setting this up with a single controller behind a router and not having to set the NAT Address for the Management interface? Should I setup a second interface on the controller to be for external management?
View 9 Replies
View Related
May 20, 2012
We have a 2504 on version 7.2.103.0 and 15 of the 1131 AG's.In short we cannot get the access points to register against the WLC, they seem to be caught up in a boot loop. They are seen on the WLC with a status of downloading, then once they have downloaded (Seen via CLI) I get an error message things I can confirm are The Country code is set to GB All ports are in Native VLAN Access points are ETSI type. It stops and restarts at syslog output DTLS-3-BAD-RECORD: Erroneous record recieved from x.x.x.x: Duplicate (replayed) record.
View 26 Replies
View Related
Mar 5, 2013
I have a 3502 AP that I am attempting to set back to factory default including clearing the username and password. It is going to work off of 4400 controllers. I have read numerous documents no how to clear the config and password but so far nothing has worked. I can get it into ap: mode but not sure what to enter here. When I do a dir there doesnt seem to be any files. It will pull an IP address via the local router but cannot communicate with WLC.
View 28 Replies
View Related
Feb 7, 2013
I am trying to configure a 1242 or 3502 WGB with PEAP. There is not ACS server involved as Windows RADIUS is used. I can get the WGB to work with OPEN Authentication but when I attempt to add in the authentication/security piece I get "no association." Below is my current config. The WLAN is set to use WPA/WPA2 802.1x + CCKM.
Current configuration : 1812 bytes
!
! Last configuration change at 00:56:39 CST Tue Mar 2 1993
version 15.2
[Code].....
View 1 Replies
View Related
Sep 25, 2012
We have installed a number of Cisco Wireless 3502-07 in China and i can not get the Clean Air Oper status to change to UP. At the meoment i have ERROR. I have have tried to disable and enable the the Clean Admin Status from the Access Point 802.11b/g/n and then select the AP and change configuration.
View 2 Replies
View Related
Apr 6, 2012
how an AP 3500 get to be registered in a controller 5508??, so, i have seen a lot of information of wireles deployment guide but i haven't understood yet how the process or flow is for getting the AP to be registered in a controller 5508, what exactly basic configuration must be done in a controller for doing it?
View 6 Replies
View Related
May 1, 2013
We have a couple of Access Points which are not registering with WLC 2500. I followed-up on the two LAPs in the dorm. They were cycling through red, amber, green, indicating they were trying to join the controller but could not.
Recently, we have changed our IP Schema for the Wireless Devices and I believe there is an IP Conflict between APs and WLC. Earlier APs were cofigured with Static IP Address assignment, thus they can't change their IP Address.
how to reset the Access Point? I know we can hard reset them by pressing the Mode button manually.
Is there another way via which this can be done witout removing the Access Points from their enclosures?
View 7 Replies
View Related
Oct 24, 2010
I am trying to locate the radiation pattern for a 3502 with an internal antenna. We have some high ceilings so the elevation pattern could impact our placement strategy.
View 6 Replies
View Related
Feb 14, 2011
I know the AP541N can support the 7921 phone but all the documentation I've read assumes the AP541N is registering the phone with a UC500 system. I was curious if there would be any problems using this AP with a 7921 at a remote site (881SRST gateway used). It would be tieing into a CUCM BE system at the central office.
View 0 Replies
View Related
Mar 2, 2012
I bought a used Aironet 3502 (air-cap3502i-a-k9) on craigslist last week and the seller said it was set up for autonomous mode. It has ap3g1-k9w7- tar. 124-25d.JA, which does allow it to run without a controller. I know it's not the latest version, but without a service contract I'm unable to access the latest firmware. When I go into the web management console, it only shows wireless N, without letting me enable A/G. The product sheet shows it should do A/G/N - is this just a byproduct of putting the autonomous ios on a 3502, or am I missing a setting somewhere to enable it?
View 3 Replies
View Related
May 20, 2012
I recently upgraded our controllers to the latest version 7 software, as I read this was one of the requirements to get them to connect. But I am not having any luck getting into a controller. Normally I plug them in to the network, they pop into the controller listed as something like AP5057.a844.xxxx and then I can finish configuring them, but a static IP on them, etc. This is the first of this model AP I have tried to deploy, so I am wondering what is different with these. or what I might be missing in the default config in the WLAN controllers. Niether of which are set to "Master" either.
View 10 Replies
View Related
Jul 30, 2012
We have been deploying 3502 APs remotely to locations with full T1s that backhaul to where I sit at HQ. Both the foreign and anchor controller are here at my location.
I am seeking to rate limit per user the bandwidth each client will get on the guest internet ssid. As you know this traffic is encapsulated in capwap between the AP and the controller so I cant use a standard ACL on the switch or router.
We are trying to keep the guest internet access usage in check on the T1 at any given site so the other ssid's & local lan traffic is not overly competing for the bandwidth.
I found the place to edit the default profiles in the controller but the documentation really isnt clear on best practices.
So I put it to you my fellow wireless engineers to suggest how you are implementing bandwidth management on your wireless guest internet.
Oh and here is my hardware & software levels.
5508wlc - forgeign
4402wlc - anchor
Software Version7.0.230.0
View 3 Replies
View Related
Jul 3, 2011
Why is my network magic software registering over 32 gigabites of memory being used?
View 1 Replies
View Related
Apr 29, 2011
Anyone gotten 7985g's to register with CME 4.0(3)? I have seen confilicting information, some say CME wont support 7985g's but some have posted configs and say its working....anyone have personal experience? Also with the "video" option configured in telephony service, will video automatically transfer when a session is started?
I tried to get this working last night, only had 30 minutes, they didnt register, but may be a seperate issue I overlooked. I have a 3845 with c3845-adventerprisek9-mz.151-4.M.bin. I just tried to throw together a quick ephone with the mac and type 7985g but no-go.
View 1 Replies
View Related
Jan 6, 2011
I have a CME on the other end of my MPLS network. When troubleshooting phone issues i setup a phone on the CME system in question and point its TFTP server to the address of the CME router. Now, i need to point this phone to another CME but it keeps registering with the previous one no matter what i do (the TFTP server is pointed to the new CME). I have tried turning off the auto register, and i have deleted the ephone and its mac address all together but it always registers with the wrong CME.
The phone is a 7962 with a 7914 expansion module.
View 10 Replies
View Related
Apr 12, 2011
register Panasonic Cordless phone - model - KX-TGP500.While configuring in CME - ephone - type (the list available is for only cisco models).how can i register this new model which the CME.
View 4 Replies
View Related
Feb 19, 2013
I am moving an IP Phone from one subnet to another subnet.I have deleted the IP Phone configuration in call manager(System version: 7.0.1.11000-2); however, when adding the same device (same MAC address) again in the call manager, the call manager associates the phone with the old IPv4 address (even though the phone is turned off). The phone is booting up and getting a different IP address on the new subnet, and is always in the "Registering" state. The phone has the right CM IP, TFTP IP, etc. the only difference is the phone IP address and the IP address that the CM is showing in the phone device configuration. I also tried resetting/rebooting and restore phone to default factory setting but it doesn't work, i have few more devices on this new subnet that are working fine.
View 5 Replies
View Related
Jan 1, 2007
Currently have a WLC4402 installed with 21 AP's reporting to it. The controller is running at LWAPP3 with version 3.2.116.21. The WLC was purchased prior to Cisco buying Air-e-space, and has a 36 AP license. When attempting to install additional 1242AG-A-K9 ap's, the controller will not acknowledge them. I have verified the LAN confiuration as correct, and working properly.
View 9 Replies
View Related
Jun 7, 2012
A couple of our remote users are saying that during the day, suddenly their 7965 that hangs off their 881 will start registering for 3 to 5 seconds, then it will be fine.
View 8 Replies
View Related
Oct 3, 2011
I have 2106WLC and 1522AP. when i connect AP wih controller it gets the IP from DHCP pool define in controller and then start downloading the image then comes in registerd statebut problem is that when i click on the Ap to configure then suddenly its disappear and message comes the device is not available currently. at that time i check the CLI of AP and AP again becomes in Discovery state. and start process forever again of discovery.
View 2 Replies
View Related
Feb 21, 2012
I try to remplace WLC because the old wlc (7.0) is capacity full.but the AP (3502) do not "registered" to new WLC (7.3),If you have a idea, without make a reset factory to AP.
View 1 Replies
View Related
Mar 11, 2013
I try to replace WLC because the old wlc (7.0) is capacity full. but the AP (3502) do not "registered" to new WLC (7.3). Don't want to make a reset factory to AP..
View 3 Replies
View Related