Cisco Wireless :: WAP4410N 2.0.3.3 Firmware Totally Broken?

Oct 23, 2010

I have tried to upgrade from 2.0.2.1 ever since 2.0.3.3 was released back in July.  The firmware image file has remained the same, so I don't think they've ever changed it from the original July release.The download and installation go fine, I even reset to factory defaults.  The problem is that several menu selections are broken, and don't allow you to save your choices, i.e, you can't even rename your SSID.  You can type it in a Apply, but the fields just reset.  I figured this would be fixed with a minor update to 2.0.3.3, but we are now several months since original release and nothing has changed. I have tried this firmware at least three times now.  I have not bothered lately, because I don't want to waste another 30 minutes trying it and reverting back to 2.0.2.1 if this newest firmware is not going to work.

View 3 Replies


ADVERTISEMENT

Cisco Wireless :: WAP4410N-E V02 In Bridge Mode - Broken Connection

Dec 13, 2012

I have been using WAP4401N for almost a year in our office and I’m very happy of this device, never had any problem. So I bought 3 new ones for our customer which supposed to work in configuration below:
 
Network ----- AP1 –Bridge mode ----- AP2 – Bridge mode -----AP3 – Access Point mode.
 
Everything was working perfectly fine to the moment than bridge was broken. I can get access to all AP (obviously when connected to proper part of network) however not able to ping from AP2 -> AP1 or opposite so basically no link between AP1 and AP2. After reboot everything is working fine to next time (happens twice in two days). When I go to System Performance can see Connection is enabled but doesn’t work.
 
I upgraded firmware to latest version (2.0.5.3) but haven’t worked. When I’ve done some research found many users having similar problem with this device and basically they recommend to don’t buy. Unfortunately this is not an option for me as I’ve already purchased them.

View 6 Replies View Related

Linksys Wireless Router :: Incoming / Outgoing Logging Broken On E2500 Firmware

Jun 20, 2012

Have a few of these routers internally as well as at various clients.  The incoming and outgoing logs show up blank, even when there are 10-20 computers using the Internet and I know there is traffic being generated.  DHCP and security logging still works fine.  I also have a few E1200s on the latest firmware that are logging just fine... I'm just having issues with the E2500s.

View 6 Replies View Related

Cisco Routers :: RV110W Port Forwarding Still Broken In 1.2.0.9 Firmware

May 3, 2012

I installed firmware version 1.2.0.9 a couple weeks ago after seeing in the release notes that the port forwarding bug where clients would get 'no route to host' was resolved (one of the original posts found here:URL
 
After installing the firmware and confirming it's running I've seen no improvement. I still must reboot my router 2-3 times daily so clients can access the ports that are defined in the port forwarding module.

View 23 Replies View Related

Cisco Wireless :: New Firmware Required For WAP4410N

May 11, 2011

as the subject .. All those who have the WAP4410N ...want the new firmware 2.0.4.1 and solve the AP problems of stops an repeat.  believe in CISCO.

View 28 Replies View Related

Cisco Wireless :: WAP4410N Firmware Update Crashes Router

Sep 23, 2010

I recently upgraded the firmware from 2.0.2.1 to 2.0.3.3 and when the router rebooted the interface was missing many items.  On the basic setup page the boxes were missing to set the local ip address, subnet mask and anything below that.  On the Wireless Security page the security mode box was half it's size and did not have any options in it.  The wireless isolation wpa algorithm, preshared key and key renewal boxes were missing too.  I rebooted the router and still got the same thing.  I was able to get into administration and reset to the factory default.  Once the router rebooted I was unable to get into the interface at all.  It wouldn't come up at all. The power and light were blinking but I was unable to connect to it.  I tried to connect with 192.168.1.245 and the one I had set manually but no luck with either.  I was able send back the router for an exchange with Cisco.  I received the new one today.  It started up and everything worked great. I decided to try the firmware upgrade again.  I went from the firmware version that was on there(I didn't right down)  to 2.0.2.1 and the upgrade worked as the other 3 I have.  I than tried the 2.0.3.3 upgrade and I got the same thing as the other router I sent back. I have 3 other routers in place that I will not be upgrading at this point.  I should not have tried the upgrade again on the one today but being a bank the examiners like everything up to date and it's part of the monthly check.

View 2 Replies View Related

Cisco Wireless :: WAP4410N Loses Connection - Firmware Updated

Sep 17, 2012

We have three WAP4410N that loses the connection. We've updated the firmware, changed the equipment, repeatedly reconfigured,  but the problem persists.Is used the firmware 2.0.5.3 with WPA2 Enterprise Mixed authentication.

View 5 Replies View Related

Cisco Wireless :: WAP4410N Firmware 2.0.4.2 Bug - 300Mbps Data Rate Not Possible

Nov 17, 2011

I've spent parts of the past five days buying and exchanging several WAP4410N units because I was not able to achieve anything close to a 300Mbps data rate. I also tried various wireless-n network cards which were known to be configured correctly for 300Mbps speeds with no luck.
 
The highest speed I was able to achieve was 130Mbps, which is an indication that channel bonding is not in effect.
 
Then I came across another post in the forums:
 
WAP4410N does not exceed 130Mbps in N mode at close range.
 
where the OP mentions recently upgrading to firmware 2.0.4.2, though not treating that as the cause of his problems.
 
On a lark, I tried downgrading to both firmware 2.0.2.1 and firmware 2.0.3.3, and to my surprise, I was able to achieve the full 300Mbps data rate with both firmware versions.
 
When I reverted back to 2.0.4.2, I was not able to achieve the full 300Mbps data rate.
 
So, right now, I downgraded to firmware 2.0.3.3 so I can get the higher data rate, though there are other quirks to deal with.
 
Furthermore, when I do a web search of reviews, I can see that the inability to achieve the 300Mbps data rate is a huge source of complaints.

View 10 Replies View Related

Cisco Wireless :: WAP4410N Firmware Upgrade Turns AP Into Read-Only Device

Oct 16, 2012

My WAP4410N AP is running version 2.0.2.1 firmware which is quite old. There are newer firmware releases available which I'd like to upgrade to (fix the known bugs, etc.).
 
So I upgrade my firmware from version 2.0.2.1 to any of the following versions:

- 2.0.3.3
- 2.0.4.2
- 2.0.5.3
 
The AP reboots and my settings are all still there.
 
I go to change any of the settings I have - DNS, Time Zone, PSK, any field which can be edited and click Save.
 
The Save takes place and the screen refreshes to the old settings - the new settings don't stay in place after the Save.
 
I've also factory defaulted the AP prior to the upgrade, upgraded and then been in the same place unable to save any changed settings.
 
System details:
Information PID VID:  WAP4410N-E V02
Device: WAP4410N Wireless-N Access Point with Power Over Ethernet Software Version:  2.0.2.1

View 4 Replies View Related

Cisco WAN :: WAP4410n Firmware Upgrade?

Sep 17, 2012

I currently have 3 WAP4410n's (actually, they're WAP4410N-E V02s) that have been really unreliable since I got them - so much so that we've had to cron a restart script on another server which is frankly ridiculous - they've always run firmware version 2.0.2.1.
 
I've tried updating the firmware to new versions in the past with no success - when I do so, it looks like everything's fine, but when I log back in, the fixed IP address information isn't shown, and the wireless is disabled.  I can enable it, but I can't select a channel.
 
At this point, I have to revert back to the old firmware.  I've tried restoring to factory setttings before and after the firmware flash, but this hasn't changed anything.
 
However, recently I was able to flash firmware 2.0.5.3 onto only one of the routers - it worked fine and all information was displayed and wireless enabled correctly.  However on the other two, no matter what I try, the firmware won't upgrade succesfully - it looks like everything's fine, but the fixed IP information isn't shown and wireless/channels are disabled.

View 5 Replies View Related

Cisco Wireless :: Setup WRVS4400N To Isolate Guest Totally From Internal SSID

Jan 25, 2011

A query here with regards to Wireless isolation between SSID and wireless isolation within SSID.If we have 2 SSID, eg. InternalSSID, GuestSSID on AP1.Both SSID are set to Enabled for isolation between SSID, and within SSID, that would mean all machines connected thro' this AP1, would be isolated from one another.
 
1) If there's 1 laptop that connects to another AP, lets call it AP2, (doesn't have isolation function) on ssid01. Would this laptop still be isolated from those that connects to the first AP?
 
2) If there are wired PCs connected to the router. And the 2 APs are connected to the same router. Would the machines connected thro' the AP1 on either InternalSSID, GuestSSID be able to access those wired PCs? (My assumption is yes.)
 
3) Is there a quick and efficient way to setup on WRVS4400N to isolate GuestSSID totally from InternalSSID, and wired PCs. InternalSSID and wired PCs should be allowed to 'see' one another.

The challenge here is that, the network points are all installed already. Both AP are connecting thro' 2 separate unmanaged switch together with a couple of other PCs. 1 Port on the unmanaged switch, each,connects to the router.

View 1 Replies View Related

Linksys Wireless Router :: E4200 - Disable Wi-Fi Totally And Use Wired Connection?

Sep 6, 2011

Can we disable wireless totally in E4200 and just use wired connections? I didn't see any configuration for that, but just in case I missed it. I'm also aware we can disable SSID Broadcast.

View 1 Replies View Related

Ubuntu 10.04 - Wireless Connection Works Great But Wired Is Totally Dead

Mar 18, 2012

I am running Ubuntu 10.04 on my Acer Aspire One netbook.The wireless connection works great, but the wired is totally dead.

When I plug the Ethernet wire, the little led next to the port doesn't blink.

If I do ifconfig, this is the output:

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:1659 errors:0 dropped:0 overruns:0 frame:0
TX packets:1659 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0

[code]....

There is no eth0. Is that normal?

In the "Network Connections" GUI there is an entry "Wired connection 1", its "MAC address" field is blank.

How can I make the wired connection work?

View 2 Replies View Related

Cisco Wireless :: 802.11 WAP4410N To WAP4410N Backhaul Using N Protocol?

Apr 30, 2011

I have the following equipment:
 
Cisco 871W router
2x WAP 4410N APs running 2.0.3.3

I currently have 1 AP connected to the router via copper.  The AP to AP link is over 802.11.  I have attached a diagram reflecting the current topology.
 
The AP-to-AP link will come up utilizing B/G/N mixed mode; however, the connection is basically unusable.  About 30% of the traffic is dropped, while the packets that do make it have a consistently volatile latency, anywhere from 15 to 1500 ms. I have had success using G-only and B/G mixed.  The link is stable (I have had the best results with B/G).  The problem is, I didn't buy the 2nd 4410N to run the G protocol.  I would like to connect the APs running either B/G/N (hopefully negotiating to N) or N only.  I am wondering if there is a certain configuration I can utilize (perhaps using WDS repeater or bridge versus Wireless Client/Repeater?), or a firmware upgrade set for release that can make this happen for me.

View 1 Replies View Related

Combining Two Totally Different Networks?

Aug 10, 2012

I am trying to work out a way of combining two networks from two (Internet Service Providers or ISPs. One network is for Internet, and the second one is for CCTV cameras. Both networks exist and are working independently, each with its own servers. I want to re-design the whole system such that at any one time t, a supervisor with an Internet connection in his office can be able to see what is happening on cctv cameras without contacting the cctv personnel.

View 6 Replies View Related

When Check Internet Usage Log On Wireless Company The Usage Is Totally Off?

Apr 3, 2013

however recently when i check my internet usage log on my wireless company (Rogers) the usage is totally off from what my bandwidth tracker shows me. So i decide to turn off my wifi and see what happens, there has always been this weird wifi connection appearing whenever my wifi appears, then afterwards when i turn off my wifi the suspicious wifi connections disappear. is this possible that someone is using our wifi? i might just be overreacting but it has brought me to concern that if the usage continues my family will have to end up paying over $30 for extra internet use. it is very frustrating me because when i check my DHCP client table it only shows 3 connection, ethernet - my desktop which is not turned on, 2 wireless connection - my laptop and my sister's laptop.

View 6 Replies View Related

Cisco Wireless :: WLC5508 VoIP Connectivity Is Broken

Jun 22, 2012

I have a  WLC5508 and 25  LAP 1041. I use two wifi, one with RADIUS for data and other with wpa-psk for voip. The problem is the voip conectivity is broken.How can i improve the handover?

View 11 Replies View Related

Link Between Computer And Wireless Adapter Is Broken

Aug 26, 2012

I have a new wireless router (new network, entirely). I used to get intermittent "network access denied" messages. Now, I get intermittent connectivity loss: "No internet access." I typically just right click and troubleshoot. The problem is solved and I get the following message: "Problem with wireless adapter or access point." Once fixed, things go on well for a random time (never more then a day). Then, however, they just fall apart.

View 9 Replies View Related

Cisco Wireless :: 602-OEAP Access Point Broken After WLC Upgrade To 7.4.100.0

Mar 7, 2013

I have a TAC case open, but it doesn't seem to be making any progress.I upgraded my 5508 controller from 7.2.111.3 up to 7.4.100.0..Most of my APs are fine. 3500s, 1100s etc.except for 602i APs. The APs associate, they update software etc, but they won't broadcast the WLAN.An interesting thing, on the 602 AP, in the log, I see this:*Mar 06 15:08:12.667: SSID remote, WLAN Profile Name: RemoteOEAP, added to the slot[0], disabled..So the AP is definately talking to the WLC and being pushed the correct WLAN profile.On the controller, the AP shows the the Admin status of the radios is showing DOWN, but the Admin status on the AP itself shows UP
 
I've done a factory reset on the APs to no avail. I have a 2504 WLC as well that i'm in the process of implementing in a DMZ specificially for these APs, and for testing purposes, I associated the 602 Ap to that WLC as well. This one is running 7.4.100.0 too, same results. It would appear to be a problem with this version of software?

View 6 Replies View Related

Dell N5110 / Wireless Network Adapter Broken

May 30, 2012

My laptop's wireless network adapter is not working Eventually I managed to re install the driver but that did absolutely nothing and now it won't connect unless I have the ethernet cable plugged in. It also no longer will tell me there is a problem with the adapter, it just refuses to bring up any wireless connections. My laptop is a Dell N5110.

View 1 Replies View Related

Linksys Wireless Router :: EA6500 DHCP Is Broken?

Sep 30, 2012

Generally works on wireless Guest network. Only allows one IP on wired or wireless. Using latest cloud firmware.
 
Instead of giving out the 192.168.1.100-150 as configured. It will give out from the cable modem (i think) 192.168.100.x
 
Seting static IP on computers works fine.

View 9 Replies View Related

Linksys Wireless Router :: WRT54G Administrator Page Is Broken?

Sep 27, 2012

I recently "uninstalled" DD-WRT from my router and tried to install the actual firmware for the router, so I went to this page [URL] WRT54G and select version 5. My router is really version 5.1 but I read on this forum that this router works with version 5 so I downloaded it and installed it.
 
However, this is how my admin page looks like,
 
And I can't do anything at all. Is there a fix for this? Is there an actual version 5.1 firmware? Or must I switch to a different, proper router?

View 8 Replies View Related

Linksys Wireless Router :: SPAM Broken Packets By E4200

Nov 17, 2011

I have a problem with e4200. Buy it about 1 month ago with firmware 1002, link to ISP by simple LAN with DHCP IP lising without any method of identification like PPOE or other. 2 days ago tech support of ISP call me nd say that my router send bad packet to their hardware and all LAN collups include DNS server. I disconnect all device from router but same thing happened. I update firware to 1003 but this action work for 1 day, and again tech support call me. What wrong with router or may be with ISP technician's hands?

View 3 Replies View Related

Linksys Wireless Router :: WRTP54G Route Table - Broken Internet Access

May 2, 2011

I know that WRTP54G is a voip device, but it is router as well and my problem is related to routing part.I cannot access public internet servers with IP in subnet 2.0.0.0 / 8 and 1.0.0.0 / 8. In the 2.0.0.0 / 8 subnet are some akamai cdn servers (yes, the fbcdn .After some time I've found, that routing table in wrtp54g contains also entries:
 
1.0.0.0                 0.0.0.0                 255.0.0.0                 LAN&Wireless2.0.0.0                 0.0.0.0                 255.0.0.0                 LAN&Wireless

which cannot be deleted. It looks like someone wanted to filter dark space when the router was developed.Is there any way, to get rid of it? I've restored to factory defaults, no change. Firmware version is 3.1.27.ETSI

View 9 Replies View Related

Cisco WAN :: Router 2612 Having Broken NAT

Mar 22, 2013

I have a cisco router 2612 where NAT is defined ip nat inside source static tcp 192.168.1.63 80 175.x.x.x 80 extendable It appears that after sometime (may be in few hours) the NAT is broken and I no longer can access the server over port 80 externally.

View 3 Replies View Related

Cisco :: AP802GN - Broken Web Management

Jan 30, 2013

I recently upgraded an  AP802GN-E-K9 to version 15.2(2)JB (ap802-k9w7-mx.152-2.JB), which broke the web interface. The http server is still running, however the web interface is not available. The following is displayed instead Navigating to /ap_home.shtml etc shows the correct pages. Extracting the "tar" file from the Cisco site and looking in the /html/level/15/ directory in both the tar and flash shows files missing that I'd expect to exist ( frameHome.html , navHome.html etc ).
 
Alas, I have no SmartNet on this device (embeded into my 887VA-W) as it's for home

View 2 Replies View Related

Cisco Switches :: Broken SG 200-08p Switch - Blinking LED?

Aug 21, 2011

I turned unplugged it and plugged it back in.  Now its blinking green power LED.  Is it dead?

View 2 Replies View Related

Cisco WAN :: Broken Pat / Overload After Upgrade From 1711 To 891

Apr 26, 2011

Broken Pat/Overload after upgrade from 1711 to 891

View 7 Replies View Related

Ethernet Cable Not Recognized (not Broken)?

Sep 15, 2011

I have searched the forums and found that there have been others with the same problem as me,but none of the solution offered was working for me so I decided to start this thread.I have an Acer laptop that wont recognize my ethernet cable, it says that there is no cable connected.

View 1 Replies View Related

Internet Not Working / Firewall Is Broken

Jan 24, 2013

I can't find the problem in firewall..

View 3 Replies View Related

Is Wifi Broken On Toshiba Laptop

Jan 20, 2012

Yesterday I was on my toshiba satelite L550-OCD and the wireless wasn't working then it started working again. I closed my laptop and when I went back to it it wasn't working again and hasn't since. It says there's no wireless connection to plug in Ethernet cable now I have tried Fn F8 and it doesn't do anything. So I went into my toshiba assist and opened optimize. Then toshiba hardware settings and clicked LAN and it says it's turned on. But when I click radar it shows it is not connected and the light is off.

View 6 Replies View Related

Internet Port Broken On WNDR4500?

Dec 1, 2012

I recently swapped a router out for an old one to check an internet problem (to rule it out basically) and when I tried swapping the newer (better) one back in it networks fine (ie computers can see/stream off each other) but it doesnt recognize as being plugged into the internet.

After doing a factory reset via routerlogin.net I still have the same problem. The only thing I can think of is maybe the port got damaged? (The ethernet cables all work fine).

My process for hooking up the new router in case I was doing something wrong:

Unplug cable modem power, swap all the cords, on router while cable modem was rebooting and then once modem connected I turn on router. Did I need to restart the PC as well? Is that why this is screwing up?

View 2 Replies View Related

D-Link DIR-615 :: CD Broken - How To Get To Installation Wizard

Feb 23, 2011

i have already installed this, but it stop working so i unplugged it, now cant find the CD

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved